1998

Ford 1998 User manual

  • Hello! I am an AI chatbot trained to assist you with the Ford 1998 User manual. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
Before driving
Introduction 2
Instrumentation 4
Controls and features 17
Seating and safety restraints 48
Starting and driving
Starting 76
Driving 83
Roadside emergencies 131
Servicing
Maintenance and care 152
Capacities and specifications 205
Reporting safety defects 215
Index 216
All rights reserved. Reproduction by any means, electronic or mechanical
including photocopying, recording or by any information storage
and retrieval system or translation in whole or part is not permitted without
written authorization from Ford Motor Company.
Copyright
r
1997 Ford Motor Company
Elemental Chlorine Free
Contents
1
ICONS
Indicates a warning. Read the
following section on Warnings for
a full explanation.
Indicates vehicle information
related to recycling and other
environmental concerns will follow.
Correct vehicle usage and the
authorized disposal of waste
cleaning and lubrication materials
are significant steps towards
protecting the environment.
WARNINGS
Warnings provide information
which may reduce the risk of
personal injury and prevent
possible damage to others, your
vehicle and its equipment.
BREAKING-IN YOUR VEHICLE
There are no particular breaking-in
rules for your vehicle. During the
first 1 600 km (1 000 miles) of
driving, vary speeds frequently.
This is necessary to give the
moving parts a chance to break in.
If possible, you should avoid full
use of the brakes for the first
1 600 km (1 000 miles).
INFORMATION ABOUT THIS
GUIDE
The information found in this
guide was in effect at the time of
printing. Ford may change the
Introduction
2
contents without notice and
without incurring obligation.
SPECIAL NOTICES
Using your vehicle with a
snowplow
For more information and
guidelines for using your vehicle
with a snowplow, refer to the
Driving chapter.
Using your vehicle as an
ambulance
Do not use this vehicle as
an ambulance.
Your vehicle is not equipped with
the Ford Ambulance Preparation
package.
Notice to owners of utility type
vehicles
Before you drive your vehicle,
please read this Owner’s Guide
carefully. Your vehicle is not a
passenger car. As with other
vehicles of this type, failure to
operate this vehicle correctly may
result in loss of control or an
accident.
Be sure to read Driving off road
in the Driving chapter as well as
the “Four Wheeling” supplement
included with 4WD and utility type
vehicles.
Introduction
3
10
H
C
20
30
40
50
60
70
80
90
100
0
0 RPMx1000
F
20•km/h
LOW
FUEL
40•
60
80
100
120
•140
1
2
3
4
5
CHECK
ENGINE
4 X 4
THEFT
6
E
18
8
H
L
ABS
+ -
+ -
0000
000
05
0
P
ON
OFF
RES
SET
ACCEL
COAST
SRS
Headlamp control
(pg. 17)
Instrument panel
dimmer switch
(pg. 18)
Turn signal and
wiper/washer
control
(pg. 34)
Instrument cluster
(pg. 6)
Speed control
(pg. 28)
Driver side air
bag
(pg. 60)
Instrumentation
4
VOL-PUSH ON
AM
FM
BASS
TREB
BAL FADE
AUTO
SET
SEEK
TUNE
DISCS
SCAN EJ
TAPE
CD
DOLBY 8 NR
REW
1
FF
2
SIDE 1-2
3
4
COMP
5
SHUFFLE
6
ST
FM 1
FM 1
FLOOR
PANEL
LO
HI
COOL WARM
DEF
FLR&
DEF
PANEL &
FLOOR
OFF
PASSENGER AIRBAG
OFF
OFF
ON
Passenger air bag
deactivate switch
(pg. 65)
Climate control
systems
(pg. 20)
Gearshift
(includes
overdrive button)
(pg. 88)
Auxiliary power
point
(pg. 19)
4WD Control*
(pg. 102)
Electronic sound
system; refer to
Audio Guide
(pg. 19)
Instrumentation
5
WARNING LIGHTS AND CHIMES
Standard instrument cluster
Optional instrument cluster
Low fuel
Illuminates when the fuel level is
low. The lamp will also illuminate
when the ignition key is turned to
ON and the engine is off.
Check engine
Your vehicle is equipped with a
computer that monitors the
engine’s emission control system.
This system is commonly known as
DOOR
AJAR
BRAKE
FUEL
RESET
CHECK
SUSP
LOW
RANGE
4 X 4
!
+ -
LOW
FUEL
ABS
CHECK
ENGINE
UNLEADED FUEL ONLY
E
F
H
C
L
H
8
18
0
0000
00000
MPH
20
km/h
40
60
80
100
120
140
160
0
PRN 21
10
20
30
40
50
60
70
80
90
100
D
LOW
FUEL
DOOR
AJAR
BRAKE
FUEL
RESET
CHECK
ENGINE
LOW
RANGE
4 X 4
!
ABS
+ -
THEFT
L
E
F
H
0
0000
RPM
1000
X
00000
MPH
20
km/h
40
60
80
100
120
140
160
0
0
1
2
3
5
6
4
PRN 21
10
20
30
40
50
60
70
80
90
100
8
C
18
H
D
CHECK
SUSP
FUEL DOOR
LOW
FUEL
CHECK
ENGINE
Instrumentation
6
the On Board Diagnostics System
(OBD II). This OBD II system
protects the environment by
ensuring that your vehicle
continues to meet government
emission standards. The OBD II
system also assists the service
technician in properly servicing
your vehicle.
The Check Engine indicator light
illuminates when the ignition is
first turned to the ON position to
check the bulb. If it comes on after
the engine is started, one of the
engine’s emission control systems
may be malfunctioning. The light
may illuminate without a
driveability concern being noted.
The vehicle will usually be drivable
and will not require towing.
What you should do if the
check engine light illuminates
Light turns on solid:
This means that the OBD II system
has detected a malfunction.
Temporary malfunctions may cause
your Check Engine light to
illuminate. Examples are:
1. The vehicle has run out of fuel.
(The engine may misfire or run
poorly.)
2. Poor fuel quality or water in the
fuel.
3. The fuel cap may not have been
properly installed and securely
tightened.
These temporary malfunctions can
be corrected by filling the fuel tank
Instrumentation
7
with good quality fuel and/or
properly installing and securely
tightening the gas cap. After three
driving cycles without these or any
other temporary malfunctions
present, the Check Engine light
should turn off. (A driving cycle
consists of a cold engine startup
followed by mixed city/highway
driving.) No additional vehicle
service is required.
If the Check Engine light remains
on, have your vehicle serviced at
the first available opportunity.
Light is blinking:
Engine misfire is occurring which
could damage your catalytic
converter. You should drive in a
moderate fashion (avoid heavy
acceleration and deceleration) and
have your vehicle serviced at the
first available opportunity.
Under engine misfire
conditions, excessive
exhaust temperatures could
damage the catalytic converter,
the fuel system, interior floor
coverings or other vehicle
components, possibly causing a
fire.
Air bag readiness
Momentarily illuminates when the
ignition is turned ON. If the light
fails to illuminate, continues to
flash or remains on, have the
system serviced immediately.
Instrumentation
8
Safety belt
Momentarily illuminates when the
ignition is turned ON to remind
you to fasten your safety belts. For
more information, refer to the
Seating and safety restraints
chapter.
Brake system warning
Momentarily illuminates when the
ignition is turned on and the
engine is off. Also illuminates when
the parking brake is engaged.
Illumination after releasing the
parking brake indicates low brake
fluid level.
Anti-lock brake system (ABS)
Momentarily illuminates when the
ignition is turned on and the
engine is off. If the light remains
on, continues to flash or fails to
illuminate, have the system
serviced immediately.
Turn signal
Illuminates when the left or right
turn signal or the hazard lights are
turned on. If one or both of the
indicators stay on continuously or
flash faster, check for a burned-out
turn signal bulb. Refer to Exterior
bulbs in the Maintenance and
care chapter.
!
BRAKE
ABS
Instrumentation
9
High beams
Illuminates when the high beam
headlamps are turned on.
Anti-theft system (if equipped)
Refer to Perimeter alarm system
in the Controls and features
chapter.
Charging system
Momentarily illuminates when the
ignition is turned ON and the
engine is off. The light also
illuminates when the battery is not
charging properly, requiring
electrical system service.
Oil pressure/Engine coolant
This light will come on when the
key is in the ON position and the:
engine coolant temperature is
very high
engine oil pressure is low
The light serves as a notice that a
system needs your attention and to
check the engine coolant
temperature gauge and the engine
oil pressure gauge.
Refer to Engine coolant
temperature gauge and Engine
THEFT
Instrumentation
10
oil pressure gauge in this chapter
for more information.
Four wheel drive low (if
equipped)
Illuminates when four-wheel drive
low is selected.
Four wheel drive indicator (if
equipped)
Illuminates when 4x4 range is
selected.
Check air suspension (if
equipped)
Illuminates briefly when the
ignition is turned to the ON
position and the engine is OFF.
The light also illuminates when the
air suspension system requires
servicing.
For information, refer to Air
suspension system in the Driving
chapter.
Door ajar
Illuminates when the ignition
switch is in the ON or START
position and any door is open.
LOW
RANGE
4x4
CHECK
SUSP
DOOR
AJAR
Instrumentation
11
Fuel reset
Illuminates when the ignition key
is turned to the ON position and
the fuel pump shut-off switch has
been triggered. For more
information, refer to Fuel pump
shut-off switch in the Roadside
emergencies chapter.
Safety belt warning chime
Chimes to remind you to fasten
your safety belts.
For information on the safety belt
warning chime, refer to the
Seating and safety restraints
chapter.
Supplemental restraint system
(SRS) warning chime
For information on the SRS
warning chime, refer to the
Seating and safety restraints
chapter.
Key-in-ignition warning chime
Sounds when the key is left in the
ignition in the OFF/LOCK or ACC
position and either front door is
opened.
Headlamps on warning chime
Sounds when the headlamps or
parking lamps are on, the ignition
is off (and the key is not in the
ignition) and either front door is
opened.
FUEL
RESET
Instrumentation
12
GAUGES
Standard instrument cluster
gauges
Optional instrument cluster
gauges
Fuel gauge
Displays approximately how much
fuel is in the fuel tank (when the
key is in the ON position). The
fuel gauge may vary slightly when
the vehicle is in motion. The
ignition should be in the OFF
position while the vehicle is being
refueled. When the gauge first
indicates empty, there is a small
amount of reserve fuel in the tank.
DOOR
AJAR
BRAKE
FUEL
RESET
CHECK
SUSP
LOW
RANGE
4 X 4
!
+ -
LOW
FUEL
ABS
CHECK
ENGINE
UNLEADED FUEL ONLY
E
F
H
C
L
H
8
18
0
0000
00000
MPH
20
km/h
40
60
80
100
120
140
160
0
PRN 21
10
20
30
40
50
60
70
80
90
100
D
FUEL
RESET
CHECK
ENGINE
LOW
RANGE
4 X 4
ABS
BRAKE
!
+ -
THEFT
LOW
FUEL
DOOR
AJAR
L
E
F
H
0
0000
RPM
1000
X
00000
MPH
20
km/h
40
60
80
100
120
140
160
0
0
1
2
3
5
6
4
PRN 21
10
20
30
40
50
60
70
80
90
100
8
C
18
H
D
CHECK
SUSP
FUEL DOOR
E
F
Instrumentation
13
When refueling the vehicle from
empty indication, the amount of
fuel that can be added will be less
than the advertised capacity due to
the reserve fuel.
Speedometer
Indicates the current vehicle
speed.
Engine coolant temperature
gauge
Indicates the temperature of the
engine coolant. At normal
operating temperature, the needle
remains within the normal area
(the area between the “H” and
“C”). If it enters the red section,
the engine is overheating. Stop the
vehicle, switch off the ignition and
let the engine cool. Refer to
Engine coolant in the
Maintenance and care chapter.
Never remove the coolant
recovery cap while the
engine is running or hot.
This gauge indicates the
temperature of the engine coolant,
not the coolant level. If the coolant
0
0000
00000
MPH
20
km/h
40
60
80
100
120
140
160
0
10
20
30
40
50
60
70
80
90
100
H
C
Instrumentation
14
is not at its proper level or
mixture, the gauge indication will
not be accurate.
Odometer
Registers the total kilometers
(miles) of the vehicle.
Trip odometer
Registers the kilometers (miles) of
individual journeys. To reset,
depress the control.
Tachometer
Indicates the engine speed in
revolutions per minute.
Driving with your tachometer
pointer continuously at the top of
the scale may damage the engine.
0
0000
00000
MPH
20
km/h
40
60
80
100
120
140
160
0
10
20
30
40
50
60
70
80
90
100
0
0000
00000
MPH
20
km/h
40
60
80
100
120
140
160
0
10
20
30
40
50
60
70
80
90
100
RPM
1000
X
0
1
2
3
5
6
4
FUEL DOOR
Instrumentation
15
Battery voltage gauge
This gauge shows the battery
voltage when the ignition is in the
ON position. If the pointer moves
and stays outside the normal
operating range (as indicated),
have the vehicle’s electrical system
checked as soon as possible.
Engine oil pressure gauge
This shows the engine oil pressure
in the system. Sufficient pressure
exists as long as the needle
remains in the normal range (the
area between the “H” and “L”).
If the gauge indicates low
pressure, switch off the engine
immediately. Check the oil level.
Add oil if needed (refer to
Checking and adding engine oil
in the Maintenance and care
chapter). If the oil level is correct,
have your vehicle checked at your
dealership or by a qualified
technician.
8
18
L
H
Instrumentation
16
HEADLAMP CONTROL
Rotate the headlamp control to the
desired position:
OFF.
Parking lamps on.
Headlamps on.
Foglamp control (if equipped)
The headlamp control also
operates the foglamps. The
foglamps can be turned on only
when the headlamps are in the
position.
Pull headlamp control towards you
to turn foglamps on. The foglamp
indicator light
(located to the
right of the control) will illuminate.
Daytime running light (Canadian
vehicles only)
The daytime running light system
turns the headlamps on, with a
reduced light output, when:
the vehicle is running
the parking brake is released
the headlamp system is in the
OFF position
PULL
FOR
FOG
P
PULL
FOR
FOG
P
Controls and features
17
The Daytime Running
Light (DRL) system will
not illuminate the tail lamps and
parking lamps. Turn on your
headlamps at dusk. Failure to do
so may result in a collision.
PANEL DIMMER CONTROL
Use to adjust the brightness of the
instrument panel.
Rotate up to brighten.
Rotate down to dim.
AUTOLAMP CONTROL (IF
EQUIPPED)
The autolamp system provides
light sensitive automatic on-off
control of the exterior lights
normally controlled by the
headlamp control.
The autolamp system also keeps
the lights on for a preselected
period of time after the ignition
switch is turned to OFF.
To turn autolamps on, rotate the
control up. The preselected time
lapse is adjustable up to
approximately three minutes by
continuing to rotate the control
upward.
To turn autolamps off, rotate the
control down until it clicks.
Controls and features
18
A small LED illuminates next to
the autolamp control to indicate
that the headlamps have been
turned on by the autolamps.
Foglamps are not controlled by
the autolamps. In order to turn
on the foglamps, you must turn
the lamp switch to the
position and pull for fog.
4WD CONTROL (IF EQUIPPED)
This control operates the 4WD.
Refer to Four-wheel drive (4WD)
operation in the Driving chapter
for more information.
AUXILIARY POWER POINT
The auxiliary power point is
located on the instrument panel.
Do not plug optional electrical
accessories into the cigarette
lighter. Use the powerpoint.
AUDIO SYSTEM
Refer to the “Audio Guide” for
instructions on how to operate the
audio system.
4H
2H
4L
Controls and features
19
CLIMATE CONTROL SYSTEM
Heater only system
(if equipped)
Fan speed control
Controls the volume of air
circulated in the vehicle.
Temperature control knob
Controls the temperature of the
airflow inside the vehicle. On
heater-only systems, the air cannot
be cooled below the outside
temperature.
Mode selector control
Controls the direction of the
airflow to the inside of the vehicle.
PANEL-Distributes outside air
through the instrument panel
registers.
OFF-Outside air is shut out and
the fan will not operate.
HI
COOL WARM
OFF
PANEL
FLOOR
DEF
FLR
& DEF
PANEL &
FLOOR
LO
HI
LO
COOL WARM
OFF
PANEL
FLOOR
DEF
FLR
& DEF
PANEL &
FLOOR
Controls and features
20
/