Toshiba MW24FPX User manual

COMBINATION FLAT COLOR

TELEVISION AND VIDEO CASSETTE

RECORDER / DVD VIDEO PLAYER

MW24FPX

MW27FPX

OWNER’S MANUAL

2

13

18

33

38

42

Introduction

Connections

Basic setup

Playback

(VCR)

Recording

(VCR)

Other functions

(VCR)

DIGITAL VIDEO

44

47

57

61

Basic playback

(DVD)

Advanced

playback

(DVD)

Function setup

(DVD)

Others

This device does not tape-record copy protected DVD video discs.

23

TV operation

Illustration of MW24FPX

5Q10501A [E]Cover 4/17/04, 11:55 AM1

2

Introduction

CAUTION:

THIS DIGITAL VIDEO PLAYER EMPLOYS A LASER SYSTEM.

TO ENSURE PROPER USE OF THIS PRODUCT, PLEASE

READ THIS OWNER'S MANUAL CAREFULLY AND RETAIN

FOR FUTURE REFERENCE. SHOULD THE UNIT REQUIRE

MAINTENANCE, CONTACT AN AUTHORIZED SERVICE LO-

CATION-SEE SERVICE PROCEDURE.

USE OF CONTROLS, ADJUSTMENTS OR THE PERFORM-

ANCE OF PROCEDURES OTHER THAN THOSE SPECIFIED

HEREIN MAY RESULT IN HAZARDOUS RADIATION EXPO-

SURE.

TO PREVENT DIRECT EXPOSURE TO LASER BEAM, DO NOT

TRY TO OPEN THE ENCLOSURE. VISIBLE LASER RADIA-

TION MAY BE PRESENT WHEN THE ENCLOSURE IS OPENED.

DO NOT STARE INTO BEAM.

Location of the required Marking

The rating sheet and the safety caution

are on the rear of the unit.

CERTIFICATION: COMPLIES WITH

FDA RADIATION PERFORMANCE

STANDARDS, 21 CFR SUBCHAPTER J.

The lightning flash with arrowhead symbol, within an equilateral

triangle is intended to alert the user to the presence of

uninsulated dangerous voltage within the product's

enclosure that may be of sufficient magnitude to constitute a risk

of electric shock.

The exclamation point within an equilateral triangle is intended

to alert the user to the presence of important operating and

maintenance (servicing) instructions in the literature accompa-

nying the appliance.

WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TO RAIN

OR MOISTURE.

WARNING: This equipment has been tested and found to comply with the limits for a Class B digital device,

pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection

against harmful interference in a residential installation. This equipment generates, uses and can

radiate radio frequency energy and, if not installed and used in accordance with the instructions,

may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation. If this

equipment does cause harmful interference to radio or television reception, which can be

determined by turning the equipment off and on, the user is encouraged to try to correct the

interference by one or more of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the distance between the equipment and receiver.

- Connect the equipment into an outlet on a circuit different from that to which the receiver is

connected.

- Consult the dealer or an experienced radio/TV technician for help.

CAUTION: Changes or modifications not expressly approved by the party responsible for compliance with

the FCC (Federal Communications Commission) Rules could void the user's authority to operate

this equipment.

COPYRIGHT: It is permissible to record television programs, films, video tapes and other material only in the

event that third party copyrights and other rights are not violated.

IMPORTANT SAFEGUARDS

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION

CAUTION:

TO REDUCE THE RISK OF ELECTRIC

SHOCK, DO NOT REMOVE COVER

(OR BACK). NO USER-SERVICEABLE

PARTS INSIDE. REFER SERVICING TO

QUALIFIED SERVICE PERSONNEL.

5Q10501A [E]p02-05 4/17/04, 11:55 AM2

3

Introduction

1. READ INSTRUCTIONS

All the safety and operating instructions should be read before the unit is operated.

2. RETAIN INSTRUCTIONS

The safety and operating instructions should be retained for future reference.

3. HEED WARNINGS

All warnings on the unit and in the operating instructions should be adhered to.

4. FOLLOW INSTRUCTIONS

All operating and use instructions should be followed.

5. CLEANING

Unplug this unit from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners.

Use a damp cloth for cleaning the exterior cabinet only.

6. ATTACHMENTS

The manufacturer of this unit does not make any recommendations for attachments, as they may cause

hazards.

7. WATER AND MOISTURE

Do not use this unit near water. For example, near a bathtub, washbowl, kitchen sink, laundry tub, in a wet

basement, or near a swimming pool.

8. ACCESSORIES

Do not place this unit on an unstable cart, stand, tripod, bracket, or table.

The unit may fall, causing serious injury, and serious damage to the unit.

8A. An appliance and cart combination should be moved with care. Quick stops,

excessive force, and uneven surfaces may cause the appliance and cart

combination to overturn.

9. VENTILATION

Slots and openings in the cabinet back or bottom are provided for ventilation,

and to ensure reliable operation of the unit, and to protect it from overheating.

These openings must not be blocked or covered. The openings should never be blocked by placing the unit

on a bed, sofa, rug, or other similar surface. This unit should never be placed near or over a radiator or heat

source. This unit should not be placed in a built-in installation such as a bookcase or rack unless proper

ventilation is provided or the manufacturer’s instructions have been adhered to.

10. POWER SOURCE

This unit should be operated only from the type of power source indicated on the rating plate. If you are not

sure of the type of power supply to your home, consult your appliance dealer or local power company. For

units intended to operate from battery power, or other sources, refer to the respective pages on this Own-

er's Manual for their operating instructions.

11. GROUNDING OR POLARIZATION

This unit is equipped with a polarized alternating-current line plug (a plug having one blade wider than the

other). This plug will fit into the power outlet only one way. This is a safety feature. If you are unable to insert

the plug fully into the outlet, try reversing the plug. If the plug should still fail to fit, contact your electrician to

replace your obsolete outlet. Instead of the polarized alternating-current line plug, your unit may be

equipped with a 3-wire grounding-type plug (a plug having a third (grounding) pin). This plug will only fit into

a grounding-type power outlet. This too, is a safety feature. If you are unable to insert the plug into the

outlet, contact your electrician to replace your obsolete outlet.

Do not defeat the safety purpose of the grounding-type plug.

12. POWER-CORD PROTECTION

Power-supply cords should be routed so that they are not likely to be walked on or pinched by items placed

upon or against them, paying particular attention to cords at plugs, convenience receptacles, and the point

where they exit from the appliance.

S3126A

PORTABLE CART WARNING

(symbol provided by RETAC)

5Q10501A [E]p02-05 4/17/04, 11:55 AM3

4

Introduction

13. LIGHTNING

To protect your unit from a lightning storm, or when it is left unattended and unused for long periods of time,

unplug it from the wall outlet and disconnect the antenna or cable system. This will prevent damage to the

unit due to lightning and power line surges.

14. POWER LINES

An outside antenna system should not be located in the vicinity of overhead power lines or other electric

light or power circuits, or where it can fall onto or against such power lines or circuits. When installing an

outside antenna system, extreme care should be taken to keep from touching such power lines or circuits,

as contact with them might be fatal.

15. OVERLOADING

Do not overload wall outlets and extension cords, as this can result in a risk of fire or electric shock.

16. OBJECT AND LIQUID ENTRY

Do not push objects through any openings in this unit, as they may touch dangerous voltage points or short

out parts that could result in fire or electric shock. Never spill or spray any type of liquid into the unit.

17. OUTDOOR ANTENNA GROUNDING

If an outside antenna or cable system is connected to the unit, be sure the antenna or cable system is

grounded to provide some protection against voltage surges and built-up static charges, Section 810 of the

National Electrical Code (NEC), ANSI/NFPA 70, provides information with respect to proper grounding of the

mast and supporting structure, grounding of the lead-in wire to an antenna discharge unit, size of grounding

conductors, location of antenna discharge unit, connection to grounding electrodes, and requirements for

the grounding electrode.

18. SERVICING

Do not attempt to service this unit yourself as opening or removing covers may expose you to dangerous

voltage or other hazards. Refer all servicing to qualified service personnel.

For example:

a. When the power-supply cord or plug is damaged.

b. If liquid has been spilled, or objects have fallen into the unit.

c. If the unit has been exposed to rain or water.

d. If the unit does not operate normally by following the operating instructions. Adjust only those

controls that are covered by the operating instructions, as an improper adjustment of other controls may

result in damage and will often require extensive work by a qualified technician to restore the

unit to its normal operation.

e. If the unit has been dropped or the cabinet has been damaged.

f. When the unit exhibits a distinct change in performance, this indicates a need for service.

19. REPLACEMENT PARTS

When replacement parts are required, be sure the service technician uses replacement parts specified by

the manufacturer or those that have the same characteristics as the original part.

Unauthorized substitutions may result in fire, electric shock or other hazards.

20. SAFETY CHECK

Upon completion of any service or repairs to this unit, ask the service technician to perform safety checks to

determine that the unit is in proper operating condition.

21. HEAT

The product should be situated away from heat sources such as radiators, heat registers, stoves, or other

products (including amplifiers) that produce heat.

22. DISC TRAY

Keep your fingers well clear of the disc tray as it is closing. It may cause serious personal injury.

23. CONNECTING

When you connect the product to other equipment, turn off the power and unplug all of the equipment from

the wall outlet. Failure to do so may cause an electric shock and serious personal injury. Read the owner's

manual of the other equipment carefully and follow the instructions when making any connections.

24. SOUND VOLUME

Reduce the volume to the minimum level before you turn on the product. Otherwise, sudden high volume

sound may cause hearing or speaker damage.

25. SOUND DISTORTION

Do not allow the product output distorted sound for a longtime. It may cause speaker overheating and fire.

26. HEADPHONES

When you use the headphones, keep the volume at a moderate level. If you use the headphones continu-

ously with high volume sound, it may cause hearing damage.

IMPORTANT SAFEGUARDS

(Continued)

5Q10501A [E]p02-05 4/17/04, 11:55 AM4

5

Introduction

EXAMPLE OF ANTENNA GROUNDING AS PER THE

NATIONAL ELECTRICAL CODE

ANTENNA

DISCHARGE UNIT

(NEC SECTION 810-20)

ANTENNA LEAD

IN WIRE

GROUNDING CONDUCTORS

(NEC SECTION 810-21)

GROUND CLAMPS

POWER SERVICE GROUNDING

ELECTRODE SYSTEM

(NEC ART 250, PART H)

GROUND

CLAMP

ELECTRIC SERVICE

EQUIPMENT

27. LASER BEAM

Do not look into the opening of the disc tray or ventilation opening of the product to see the source of the

laser beam. It may cause sight damage.

28. DISC

Do not use a cracked, deformed, or repaired disc. These discs are easily broken and may cause serious

personal injury and product malfunction.

29. NOTE TO CABLE TV SYSTEM INSTALLER

This reminder is provided to call the Cable TV system installer’s attention to Article 820-40 of the NEC that

provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be con-

nected to the grounding system of the building, as close to the point of cable entry as practical.

NEC-NATIONAL ELECTRICAL CODE

S2898A

IMPORTANT RECYCLING INFORMATION

This product uses both Cathode Ray Tube (CRT) and other components that contain lead. In

your community there might be regulations that require you to dispose these materials

properly under environmental considerations. Please contact your local authorities, or the

Electronic Industries Alliance (http://www.eiae.org) for disposal or recycling information.

TO USE AC POWER SOURCE

Use the AC polarized line cord provided for operation on AC. Insert the AC cord plug

into a standard 120V 60Hz polarized AC outlet.

Notes:

•

Never connect the AC line cord plug to other than the specified voltage (120V

60Hz). Use the attached power cord only.

•

If the polarized AC cord does not fit into a non-polarized AC outlet, do not attempt to

file or cut the blade. It is the user’s responsibility to have an electrician replace the

obsolete outlet.

•

If you cause a static discharge when touching the unit and the unit fails to function,

simply unplug the unit from the AC outlet and plug it back in. The unit should return

to normal operation.

•

If the AC cord plug is plugged in for the first time, wait for approx. 5 seconds before

pressing the POWER button.

Polarized AC Cord Plug

(One blade is wider than the other.)

AC Outlet

Wider Hole

and Blade

Power source

5Q10501A [E]p02-05 4/17/04, 11:55 AM5

Introduction

6

Precautions

Notes on handling

When shipping the unit, the original shipping carton

and packing materials come in handy. For maximum

protection, repack the unit as it was originally packed

at the factory.

Do not use volatile liquids, such as insect spray, near

the unit. Do not leave rubber or plastic products in

contact with the unit for a long time. They will leave

marks on the finish.

The top and rear panels of the unit may become

warm after a long period of use. This is not a

malfunction.

When the

unit

is not in use, be sure to remove the disc

and the video cassette turn off the power.

If you do not use the unit for a long period, the unit

may not function properly in the future. Turn on and

use the unit occasionally.

Notes on locating

Place the unit on a level surface. Do not use it on a

shaky or unstable surface such as a wobbling table or

inclined stand. The loaded disc or the video tape may

come off the proper position and cause damage to

the unit.

When you place this unit near a TV, radio, or VCR,

the playback picture may become poor and the sound

may be distorted. In this case, place the unit away

from the TV, radio, or VCR.

Notes on cleaning

Use a soft, dry cloth for cleaning.

For stubborn dirt, soak the cloth in a weak detergent

solution, wring well and wipe. Use a dry cloth to wipe

it dry.

Do not use any type of solvent, such as thinner and

benzine, as they may damage the surface of the unit.

If you use a chemical saturated cloth to clean the unit,

follow that product’s instructions.

To obtain a clear picture

The unit is a high technology, precision device. If the

video head, the head drum, the optical pick-up lens and

disc drive parts are dirty or worn down, the picture

quality becomes poor. To obtain a clear picture, we

recommend regular inspection and maintenance

(cleaning or parts replacement) every 1,000 hours of

use depending on the operating environment. For

details, contact your nearest dealer.

Notes on moisture condensation

Moisture condensation damages the unit. Please

read the following carefully.

Moisture condensation occurs, for example, when you

pour a cold drink into a glass on a warm day. Drops of

water form on the outside of the glass. In the same way,

moisture may condense on the head drum or the optical

pick-up lens inside this unit, one of the most crucial

internal parts of the unit.

Moisture condensation occurs during the following

cases.

When you bring the unit directly from a cold place to a

warm place.

When you use the unit in a room where you just

turned on the heater, or a place where the cold wind

from the air conditioner directly hits the unit.

In summer, when you use the unit in a hot and humid

place just after you move the unit from an air

conditioned room.

When you use the unit in a humid place.

Do not use the unit when moisture condensation

may occur.

If you use the unit in such a situation, it may damage

discs and internal parts. Remove the disc or the video

tape, connect the power cord of the unit to the wall

outlet, turn on the unit, and leave it for two or three

hours. After two or three hours, the unit will have

warmed up and evaporated any moisture. Keep the unit

connected to the wall outlet and moisture condensation

will seldom occur.

E

x

a

m

p

l

e

o

f

m

o

i

s

t

u

r

e

c

o

n

d

e

n

s

a

t

i

o

n

!

Tape

Head drum

Wait!

Wall outlet

5Q10501A [E]p06-12 4/17/04, 11:55 AM6

Introduction

7

Structure of disc contents

Normally, DVD video discs are divided into titles, and

the titles are sub-divided into chapters. Video CDs and

Audio CDs are divided into tracks.

DVD video disc

Video CD/Audio CD

Each title, chapter or track is assigned a number, which

is called “title number”, “chapter number” or “track

number” respectively.

There may be discs that do not have these numbers.

Notes on copyright

It is forbidden by law to copy, broadcast, show,

broadcast on cable, play in public, and rent copyrighted

material without permission.

This device does not tape-record copy protected DVD

Video Discs.

The device is not to be used for copying copyrighted

content without the express written permission of the

copyright owner.

Obtaining such permission is the sole responsibility of

the user.

This product incorporates copyright protection

technology that is protected by method claims of certain

U.S. patents and other intellectual property rights owned

by Macrovision Corporation and other rights owners.

Use of this copyright protection technology must be

authorized by Macrovision Corporation, and is intended

for home and other limited viewing uses only unless

otherwise authorized by Macrovision Corporation.

Reverse engineering or disassembly is prohibited.

On handling discs

Do not touch the playback side of the disc.

Do not attach paper or tape to discs.

On cleaning discs

Fingerprints and dust on the disc cause picture and

sound deterioration. Wipe the disc from the center

outwards with a soft cloth. Always keep the disc

clean.

If you cannot wipe off the dust with a soft cloth, wipe

the disc lightly with a slightly moistened soft cloth and

finish with a dry cloth.

Do not use any type of solvent such as thinner,

benzine, commercially available cleaners or antistatic

spray for vinyl LPs. It may damage the disc.

On storing discs

Do not store discs in a place subject to direct sunlight

or near heat sources.

Do not store discs in places subject to moisture and

dust such as a bathroom or near a humidifier.

Store discs vertically in a case. Stacking or placing

objects on discs outside of their case may cause

warping.

Playback side

Title 1 Title 2

Chapter 1 Chapter 2 Chapter 1 Chapter 2 Chapter 3

Track 1 Track 2 Track 3 Track 4 Track 5

DVD video disc

Video CD/Audio CD

Notes on discs

5Q10501A [E]p06-12 4/17/04, 11:55 AM7

Introduction

8

DIGITAL VIDEO

Playable discs

This unit can play the following discs.

•You cannot play discs other than those listed above.

•You cannot play discs of DVD-RAM, DVD-ROM,

Photo CD, etc., or non standardized discs even if they

may be labeled as above.

• Some CD-R/RWs can not be played back depending

on the recording conditions.

• This unit uses the NTSC color system, and cannot

play DVD video discs recorded in any other color

system (PAL, SECAM, etc.).

DVD

video

discs

Disc Mark

Contents

Disc

Size

Maximum

playback time

Video

CDs

Approx. 4 hours

(single sided disc)

Approx. 8 hours

(double sided disc)

Approx. 80 minutes

(single sided disc)

Approx. 160 minutes

(double sided disc)

Approx. 74 minutes

Approx. 20 minutes

8 cm

12 cm

8 cm

12 cm

Audio

+

Video

(moving

pictures)

Audio

+

Video

(moving

pictures)

Audio

CDs

Approx. 74 minutes

Approx. 20 minutes

8 cm

(CD

single)

12 cm

Audio

The following discs are also available.

DVD-R/RW discs of Video format

CD-R/CD-RW discs of CD-DA, Video CD, MP3, WMA

or JPEG format

Kodak Picture CD and FUJICOLOR CD format

Some of these discs may be incompatible.

Notes on discs (Continued)

About this owner’s manual

This owner’s manual explains the basic instructions of

this unit. Some DVD video discs are produced in a

manner that allows specific or limited operation during

playback. As such, the unit may not respond to all

operating commands. This is not a defect in the unit.

Refer to instruction notes of discs.

“

” may appear on the TV screen during operation.

A “

” means that the operation is not permitted by the

unit or the disc.

For example, sometimes it is unable to stop the

playback of copyright message of the disc when the

STOP (3) button is pressed. Alternatively, the “

” may

also indicate that the feature is not available for the disc.

Notes on region numbers

The region number of this unit is 1. If region numbers,

which stand for their playable area, are printed on your

DVD video disc and you do not find

1

or

ALL

, disc

playback will not be allowed by the player. (In this case,

the unit will display a message on-screen.)

On Video CDs

This DVD supports Video CDs equipped with the PBC

(Version 2.0) function. (PBC is the abbreviation of

Playback Control.) You can enjoy two playback

variations depending on types of discs.

• Video CD not equipped with PBC function

(Version 1.1)

Sound and movie can be played on this DVD in the

same way as an audio CD.

• Video CD equipped with PBC function

(Version 2.0)

In addition to operation of a Video CD not equipped

with the PBC function, you can enjoy playback of

interactive software with search function by using the

menu displayed on the TV screen (Menu Playback).

Some of the functions described in this owner’s

manual may not work with some discs.

5Q10501A [E]p06-12 4/17/04, 3:21 PM8

Introduction

9

Contents

Introduction

IMPORTANT SAFEGUARDS........................... 2

Precautions ...................................................... 6

Notes on discs.................................................. 7

Contents ........................................................... 9

Identification of controls ................................. 10

Connections

Antenna connections...................................... 13

Cable TV connections .................................... 14

Connecting to optional equipment.................. 15

Basic setup

Starting setup ................................................. 18

Clock setting................................................... 19

Setting the language ...................................... 22

TV/VCR operation status ............................... 22

TV operation

TV operation................................................... 23

Closed captions.............................................. 25

To memorize channels ................................... 26

Setting the V-Chip .......................................... 27

To set the on timer.......................................... 29

To set the off timer.......................................... 30

Picture control adjustment.............................. 31

Adjusting the picture preference .................... 31

Sound control adjustment .............................. 32

Stereo and Second Audio Program (SAP) ..... 32

Playback (VCR)

Loading and unloading a cassette tape ......... 33

Cassette tape playback .................................. 34

Special playback ............................................ 35

Convenient function ....................................... 36

Recording (VCR)

Recording a TV program ................................ 38

One-touch Timer Recording (OTR) ................ 39

Timer recording .............................................. 40

Other functions (VCR)

Duplicating a video tape ................................. 42

Recording a DVD/CD disc .............................. 43

Basic playback (DVD)

Playing a disc ................................................. 44

Advanced playback (DVD)

Zooming ......................................................... 47

Locating desired scene .................................. 47

Repeat playback............................................. 48

A-B Repeat playback...................................... 48

Program playback .......................................... 49

Random playback........................................... 49

Changing angles ............................................ 50

Title selection ................................................. 50

DVD menu...................................................... 50

Changing soundtrack language ..................... 51

Subtitles ......................................................... 51

Karaoke playback........................................... 52

Disc status...................................................... 52

To turn off the PBC ........................................ 52

MP3/WMA/JPEG CD operation ..................... 53

Selecting PROGRESSIVE scan..................... 56

Function setup (DVD)

Customizing the function settings .................. 57

Temporary disabling of rating level

by DVD disc ................................................... 60

Others

Language code list ......................................... 61

Troubleshooting ............................................. 62

Reception disturbances.................................. 64

Specifications ................................................. 65

Limited warranty ............................................. 66

5Q10501A [E]p06-12 4/17/04, 11:55 AM9

Introduction

10

Front panel

Rear panel

Cassette loading slot

Remote sensor

OPEN/CLOSE button

VOLUME ▲/▼ buttons

SKIP button

STOP button

PLAY button

SKIP button

POWER button

POWER

indicator

REC/OTR

indicator

TIMER REC indicator

Disc tray

AC power cord

Identification of controls

See the page in for details.

*PHONES jack

Model MW27FPX has a door on the front panel. Please open it to access the *PHONES jack and the *AUDIO (L/R)/VIDEO

IN (LINE IN 2) jacks.

Illustration of MW24FPX

This owner’s manual uses the illustrations of MW24FPX. MW27FPX model has some differences in appearance

from the illustrations. Example: Model MW27FPX has a door on the front panel.

S-VIDEO IN (LINE 1 IN)

*AUDIO (L/R)/VIDEO IN (LINE IN 2) jacks

REW (Rewind) button

STOP/EJECT button

PLAY button

FF (Fast Forward) button

REC/OTR button

CHANNEL ▲/▼ buttons

COAXIAL DIGITAL AUDIO OUT jack

AUDIO (L/R)/VIDEO OUT jacks

AUDIO (L/R)/VIDEO IN (LINE 1 IN) jacks

RF IN (VHF/UHF) jack

5Q10501A [E]p06-12 4/17/04, 3:24 PM10

Introduction

11

Remote control

* DVD MENU button

Use the DVD MENU button to

display the menu included on

many DVD video discs. To

operate a menu, follow the

instructions in “DVD menu”.

50

FWDREV

STOP

PAUSE/STILL

DISPLAY

DVDTV/VCR

CHANNEL

POWER

AUDIO

SELECT

TIMER

REC

CHANNEL

RETURN

CLOSED

CAPTION

ENTER

VOLUMEMUTE

SLEEP

PLAY

0

8

79

654

321

CM SKIP/JUMP

SLOW

SKIP

POWER button

18

MUTE button

24

VOLUME / buttons

23

CHANNEL / buttons

24

( / / / )

Direction buttons

18

27

23

44

19

Direct channel

selection buttons (0

-

9)

Number buttons (0

-

9)

TV/VCR button

DVD button

DISPLAY button

22

SLEEP button

24

AUDIO SELECT button

32

REC buttons

36

TIMER REC buttons

40

PLAY button

34

REV button

34

COUNTER RESET

button

36

ANGLE

button

50

SP/SLP

button

38

RETURN

button

57

MENU

button

19

SETUP

button

57

CANCEL/CLEAR

button

27

PROGRESSIVE

button

56

JUMP button

47

CM SKIP button

35

CLOSED CAPTION button

25

SLOW button

SKIP button

35

46

CHANNEL RETURN button

24

STOP button

34

FWD button

34

PAUSE/STILL button

35

SUBTITLE button

51

ZERO RETURN button

37

REPEAT A-B button

48

PROGRAM button

29

INPUT SELECT button

42

ZOOM button

47

D.TRACKING button

35

TOP MENU button

50

TRK

+

button

35

*DVD MENU button

50

PLAY MODE button

48

TRK

-

button

35

ENTER button

18

SKIP button

46

44

46

44

The instructions in this manual describe the functions on the remote control. See the page in for details.

5Q10501A [E]p06-12 4/17/04, 11:55 AM11

Introduction

12

Operation:

• Aim the remote control at the remote sensor and press control buttons to

operate.

• Operate the remote control within 30° angle on either side of the remote

sensor, up to a distance of approx. 5 meters.

Replace the compartment

cover.

Install two “R03/AAA” batteries

(supplied),

paying attention to the

polarity diagram in the battery

compartment.

Slide the battery compartment

cover in the direction of the

arrow.

Battery precautions:

The precautions below should be followed when using batteries in this device:

1. Use only the size and type of batteries specified.

2. Be sure to follow the correct polarity when installing the batteries as indicated in the battery compartment.

Re-

versed batteries may cause damage to the device. To avoid a potential short circuit, insert the “–” end first.

3.

Do not mix different types of batteries together (e.g. Alkaline and Carbon-zinc) or old batteries with fresh ones.

4. If the device is not to be used for a long period of time, remove the batteries to prevent damage or injury from

possible battery leakage.

5. Do not try to recharge batteries not intended to be recharged; they can overheat and rupture. (Follow battery

manufacturer’s directions.)

• Press POWER to turn the unit on or off.

• Select your desired operating mode (TV/VCR or DVD) using TV/VCR or DVD.

•Tap CHANNEL

or to move through the channels one channel at a time.

• The Direction buttons ( / / / ) are also used to navigate on-screen menu system.

•You can directly access specific channels using Direct channel selection buttons.

1

23

Remote control basics

Inserting batteries

Approx. 5 meters

Illustration of MW24FPX

Identification of controls (continued)

5Q10501A [E]p06-12 4/17/04, 11:55 AM12

13

Connections

75 ohm coaxial cable

(not supplied)

300-75 ohm matching

transformer (supplied)

300-75 ohm matching

transformer (supplied)

UHF 300 ohm

twin-lead wire

(not supplied)

VHF 300 ohm

twin-lead wire

(not supplied)

UHF 300 ohm

twin-lead wire

(not supplied)

VHF 75 ohm

(not supplied)

Antenna

jack

Antenna

jack

Antenna

jack

Combiner

(not supplied)

Antenna

jack

Combiner

(not supplied)

Connect the 75 ohm cable from the combination

VHF/UHF antenna to the antenna jack.

If your combination VHF/UHF antenna has a 300

ohm twin-lead wire, the use of the 300-75 ohm

matching transformer may be necessary.

Connect the UHF 300 ohm twin-lead wire to the

combiner (not supplied). Connect the VHF 300

ohm twin-lead wire to the 300-75 ohm matching

transformer. Attach the transformer to the combiner,

then attach the combiner to the antenna jack.

Connect the VHF 75 ohm cable and UHF 300 ohm

twin-lead wire to the combiner (not supplied).

Attach the combiner to the antenna jack.

Combination VHF/UHF antenna (Separate VHF and UHF 300 ohm twin-lead wires)

Antenna connections

If you are using an indoor or outdoor antenna, follow the instructions below that correspond to your antenna system.

If you are using a cable TV service (CABLE), see page 14 for Cable TV connections.

Separate VHF/UHF antennas (75 ohm VHF cable and 300 ohm UHF twin-lead wires)

Combination VHF/UHF antenna (Single 75 ohm cable or 300 ohm twin-lead wire)

Connections

5Q10501A [E]p13-17 4/17/04, 4:03 PM13

14

Connections

For basic cable service not requiring a converter/descrambler

box, connect the Cable TV 75 ohm coaxial cable directly to the

Antenna jack on the back of the unit.

75 ohm

coaxial cable

If you subscribe to a cable TV service in which basic channels are unscrambled and premium channels require the

use of a converter/descrambler box, you may wish to use a signal splitter and an A/B Switch box (available from the

cable company or an electronics supply store). Follow the connections shown below. With the switch in the “B”

position, you can directly tune any nonscrambled channels on your unit. With the switch in the “A” position, tune your

unit to the output of the converter/descrambler box (usually channel 3 or 4) and use the converter/descrambler box

to tune scrambled channels.

Incoming

75 ohm

Cable TV

75 ohm cable to

the unit

Antenna

jack

Antenna

jack

Converter/

descrambler

If you subscribe to a cable TV service which requires the use of a converter/descrambler box, connect the

incoming 75 ohm coaxial cable to the converter/descrambler box. Using another 75 ohm coaxial cable, connect

the output jack of the converter/descrambler box to the antenna jack on the unit. Follow the connections shown

below. Set the unit to the output channel of the converter/descrambler box (usually channel 3 or 4) and use the

converter/descrambler box to select channels.

For subscribers to basic cable TV service

For subscribers to scrambled cable TV service

For subscribers to unscrambled basic cable TV service with scrambled

premium channels

Splitter

B

A

Incoming

75 ohm

Cable TV

A/B switch

75 ohm cable to

the unit

Converter/

descrambler

Antenna

jack

Cable TV connections

This unit has an extended tuning range and can tune most cable channels without using a Cable TV converter box.

Some cable companies offer “premium pay channels” in which the signal is scrambled. Descrambling these signals for

normal viewing requires the use of a descrambler device which is generally provided by the cable company.

5Q10501A [E]p13-17 4/17/04, 4:03 PM14

15

Connections

Connecting to optional equipment

Before connecting the unit to other equipment, be sure to turn off the power and

unplug all of the equipment from the wall outlet before making any connections.

You can enjoy the TV game, camcorder or high quality dynamic sounds of DVD

video discs or audio CDs by connecting the unit to optional audio equipment.

Connecting to an audio system

Connecting a camcorder or a TV game

To playback from the camcorder or playing a TV Game, connect the camcorder to the unit as shown.

Connect the unit to your audio system.

(white)

(red)

(white)

To ANALOG AUDIO OUT

To audio inputs of the amplifier

Audio system

To AUDIO (L/R)/VIDEO IN

(LINE IN 2)

To AUDIO (L/R)/VIDEO OUT

(red)

(white)

(yellow)

(red)

(white)

(yellow)

TV GAME

Camcorder

OR

Audio cable (not supplied)

Audio/Video cable (not supplied)

INPUT SELECT

Using the audio/video inputs

Press INPUT SELECT repeatedly to select the desired mode.

“LINE1”, “LINE2” or TV channel will display on the screen for 4 seconds.

Note: In the DVD mode this key will not operate.

TV Channel LINE1

(Back)

LINE2

(Front)

Signal flow

Illustration of MW24FPX

Note:

Model MW27FPX has a door on the front panel. Please open it to access the AUDIO (L/R)/VIDEO IN (LINE IN 2) jacks.

5Q10501A [E]p13-17 4/17/04, 11:56 AM15

16

Connections

*

Connecting to an amplifier equipped with a Dolby Digital decoder

Connecting to an amplifier equipped with Dolby Surround Pro Logic

Dolby Surround Pro Logic

You can enjoy the dynamic realistic sound of Dolby Surround Pro Logic by connecting an amplifier and speaker system (right and left

front speakers, a center speaker, and one or two rear speakers).

With an amplifier equipped with Dolby Digital

Connect the equipment the same way as described in “Connecting to an amplifier equipped with a Dolby Digital decoder.” Refer to

that amplifier’s owner’s manual and set the amplifier so you can enjoy Dolby Surround Pro Logic sound.

With an amplifier not equipped with Dolby Digital

Connect the equipment as follows.

• This connection is only suitable for Video CDs and Audio CDs.

Connecting to an amplifier equipped with a DTS decoder

Digital Theater Systems (DTS)

DTS is a high quality surround technology used in theaters and now available for home use, on DVD video discs or audio CDs.

If you have a DTS decoder or processor, you can obtain the full benefit of 5.1 channel DTS encoded sound tracks on DVD video discs

or audio CDs.

Manufactured under license

from Dolby Laboratories.

“Dolby”, “Pro Logic”, and the

double-D symbol are trademarks

of Dolby Laboratories.

*

Connect one or two rear

speakers. The output sound

from the rear speakers will

be monaural even if you

connect two rear speakers.

“DTS” and “DTS Digital Out”

are trademarks of Digital

Theater Systems, Inc.

Dolby Digital

Dolby Digital is the surround sound technology used in theaters showing the latest movies, and is now available to reproduce this

realistic effect in the home. You can enjoy motion picture and live concert DVD video discs with this dynamic realistic sound by

connecting the DVD video player to a 6 channel amplifier equipped with a Dolby Digital decoder or Dolby Digital processor. If you

have a Dolby Surround Pro Logic decoder, you will obtain the full benefit of Pro Logic from the same DVD movies that provide full 5.1-

channel Dolby Digital soundtracks, as well as from titles with the Dolby Surround mark.

Connecting to optional equipment

You can enjoy high quality dynamic sounds by connecting the unit

to optional audio equipment.

Amplifier equipped with

Dolby Surround Pro Logic

Amplifier equipped with a

Dolby Digital decoder

Amplifier equipped with

a DTS decoder

Audio cable (not supplied)

To audio

input

*

This section uses the following reference mark.

To AUDIO (L/R) OUT

: Rear speaker

: Sub woofer

: Front speaker

: Center speaker

: Signal flow

75 Ω coaxial cable (not supplied)

To COAXIAL

type digital

audio input

To COAXIAL

type digital

audio input

To COAXIAL DIGITAL

AUDIO OUT

75 Ω coaxial cable (not supplied)

To COAXIAL DIGITAL

AUDIO OUT

5Q10501A [E]p13-17 4/17/04, 4:04 PM16

17

Connections

MPEG2 sound

You can enjoy motion picture and live concert DVD video discs with dynamic realistic sound by connecting an amplifier

equipped with an MPEG2 audio decoder or MPEG2 audio processor.

Connecting to an amplifier equipped with a MPEG audio decoder

Connecting to an amplifier equipped with a digital audio input

2 channel digital stereo

You can enjoy the dynamic sound of 2 channel digital stereo by connecting an amplifier equipped with a digital audio input

and speaker system (right and left front speakers).

Notes:

• DO NOT connect the COAXIAL DIGITAL AUDIO OUT jack of the unit to the AC-3 RF input of a Dolby Digital Receiver.

This input on your A/V Receiver is reserved for Laserdisc use only and is incompatible with the COAXIAL DIGITAL AUDIO

OUT jack of the unit.

• Connect the COAXIAL DIGITAL AUDIO OUT jack of the unit to the “COAXIAL” input of a Receiver or Processor.

• Refer to the owner’s manual of the connected equipment as well.

• When you connect the unit to other equipment, be sure to turn off the power and unplug all of the equipment from the wall

outlet before making any connections.

• The output sound of the unit has a wide dynamic range. Be sure to adjust the receiver’s volume to a moderate listening

level. Otherwise, the speakers may be damaged by a sudden high volume sound.

•Turn off the amplifier before you connect or disconnect the unit’s power cord. If you leave the amplifier power on, the

speakers may be damaged.

Amplifier equipped with an

MPEG2 audio decoder

To COAXIAL

type digital

audio input

Amplifier equipped with a

Digital audio input

To COAXIAL

type digital

audio input

75 Ω coaxial cable (not supplied)

To COAXIAL DIGITAL

AUDIO OUT

75 Ω coaxial cable (not supplied)

To COAXIAL DIGITAL

AUDIO OUT

5Q10501A [E]p13-17 4/17/04, 11:56 AM17

18

Basic setup

Press POWER.

The starting setup function begins and the

Language setup menu appears on the screen.

Press

or to select your desired language,

then press ENTER.

Starting setup

The STARTING SETUP function makes installing your unit easily. It leads you

the Language selection, TV/CABLE selection and auto channel memory

automatically.

IMPORTANT: Make sure that the antenna or cable TV system connection

is made!

Starting setup

Press or to select “TV” or “CABLE”, then

press ENTER.

Press

or

to select “START”, then press

ENTER.

If you select “CANCEL” and press ENTER, the

STARTING SETUP stops and changes to the TV

screen.

1

2

3

Now the “AUTO CH MEMORY” and “AUTO

CLOCK”starts.

After the starting setup is completed, the TV

channel appears on the screen.

4

POWER

/

ENTER

POWER

LANGUAGE/IDIOMA/LANGUE

ENGLISH

ESPAÑOL

FRANCAIS

//

ENTER

><

CHANNEL PLAN

TV

CABLE

//

ENTER><

//

ENTER><

AUTO SETUP

START

CANCEL

AUTO CH MEMORY

STOP : CANCEL

ENTER

Notes:

• The starting setup function will work only when you press the

POWER button for the first time.

• In “AUTO CLOCK” setting, it may take more than 10 minutes

to read the EDS signal for one channel, which has only “Time

of day” or “Local time zone”.

5Q10501A [E]p18-21 4/17/04, 11:56 AM18

19

Basic setup

Clock setting

The auto clock function will automatically set the built-in clock (Month, Day,

Year and Time) when the unit is connected to an antenna or cable system

and it is turned off. As the unit searches for a receivable station in your area

and it receives a broadcast signal for auto clock, the auto clock needs

several minutes to set itself.

Preparation:

• Connect the antenna or cable system.

• If you use a cable box, turn it on.

• Plug the AC power cord to the AC outlet.

Auto clock setting

Make sure the unit is turned off.

• If you press POWER, the Auto Clock

set is not effective.

1

Wait at least three minutes and press POWER.

Then press TV/VCR to select TV/VCR mode.

The POWER indicator will light.

2

Press DISPLAY to check the clock on the

screen.

3

If the clock is not set, check the antenna

condition. The Auto clock may not function

properly if the reception condition is not

good.

4

Auto clock adjustment

To set auto clock to OFF

POWER

The Auto clock adjustment will be performed at

12:00 PM everyday if you turn off the unit.

• If you use a cable box and you want Auto Clock adjust

ment to be performed, the cable box must be left on.

• The Auto Clock adjustment is not effective when there is a

difference of more than 5 minutes exists between the

built-in clock time and the actual time.

When shipped from factory the AUTO CLOCK is set to “ON”.

But if you do not want auto clock set (Adjustment):

Press MENU, then press or to select

option.

1

Press or to select “AUTO CLOCK”.

2

Press

or

to select “OFF”.

3

Press MENU repeatedly until the menu

screen is cleared.

• When the AUTO CLOCK is set to

“OFF”, the Auto Clock adjustment

does not function.

• Set the clock manually

21

.

4

POWER

/ / /

DISPLAY

MENU

ENTER

TV/VCR

POWER

Notes:

• If the unit does not operate properly, or No key operation

(by the unit and/or the remote control): Static electricity,

etc., may affect the player's operation. Disconnect the AC power

cord once, then connect it again.

• The TV section has its own menu and also DVD section has

its own menu .

•

If no buttons are pressed for more than 60 seconds, the TV/VCR

menu screen will return to normal TV operation automatically.

5Q10501A [E]p18-21 4/17/04, 11:56 AM19

20

Basic setup

Press MENU, then press or to select

option.

1

Press

or

to select “STANDARD TIME”

, then

press

.

2

Press / / / to select your time zone, then

press ENTER.

3

Press MENU repeatedly until the menu

screen is cleared.

4

In the rare event that you live within broadcast range of two

stations in two different time zones, the unit may recognize

the wrong station for the auto clock set.

To correct the situation:

Note:

To be able to select the standard time, the clock must first be

set by “AUTO CLOCK” once.

Press or to select “DAYLIGHT SAVING

TIME”, then press

.

2

Press or to select one of the options, then

press ENTER.

3

Notes:

• When shipped from factory, the DAYLIGHT SAVING TIME is

set to “AUTO” position.

• When the clock is not set, Daylight Saving Time setting is not

available.

• When there is no Daylight Saving Time in your area, always

select “OFF” position in step 3.

When you want to set the Daylight Saving Time manually,

on the first Sunday in April you set to “ON”, and on the last

Sunday in October you set to “OFF”.

ON:

OFF:

AUTO:

for manual setting (forward one hour)

for manual setting (back one hour)

for automatic setting (read EDS in the signal)

ATLANTIC : GMT–4hours

EASTERN : GMT–5hours

CENTRAL : GMT–6hours

MOUNTAIN : GMT–7hours

PACIFIC : GMT–8hours

ALASKA : GMT–9hours

HAWAII : GMT–10hours

AUTO : AUTO SET

(GMT: Greenwich Mean Time)

To set daylight saving time

You can set the Daylight saving time automatically or

manually.

To set standard time

Press MENU repeatedly until the menu screen

is cleared.

4

ENTER

Press MENU, then press or to select

option.

1

ENTER

Clock setting (continued)

5Q10501A [E]p18-21 4/17/04, 3:28 PM20

Page is loading ...

Toshiba MW24FPX User manual

This manual is also suitable for

Toshiba MW24FPX User manual

Related papers

Other documents