Myfox 4 Buttons Remote Control User manual

Myfox
Brand
Myfox
Model
4 Buttons Remote Control
Category
Remote controls
Type
User manual

Myfox 4 Buttons Remote Control

The Myfox 4 Buttons Remote Control allows you to easily and conveniently control your Myfox security system. With its four buttons, you can:

  • Arm your system in partial mode (only some of the intrusion detectors are active).
  • Arm your system in total mode (all of the intrusion detectors are active).
  • Disarm your system and stop the siren if it has been triggered.
  • Trigger the auxiliary function programmed on your main unit (panic alert or scenario).

Myfox 4 Buttons Remote Control

The Myfox 4 Buttons Remote Control allows you to easily and conveniently control your Myfox security system. With its four buttons, you can:

  • Arm your system in partial mode (only some of the intrusion detectors are active).
  • Arm your system in total mode (all of the intrusion detectors are active).
  • Disarm your system and stop the siren if it has been triggered.
  • Trigger the auxiliary function programmed on your main unit (panic alert or scenario).
Four-button remote control
User Instructions
2. Connection to the main unit
4. Technical characteristics
Go into learning mode on your main unit
Press buttons 1 and 4 together (Partial arming and Disarming) and hold for six seconds
After six seconds, the LED flashes.
The main unit emits an audible signal to confirm successful connection
You can personalize your remote control via your Internet user access
Compatibility: refer to the list of compatible units
on www.myfox.me/support
Cat. No. : FO 3004
Frequency: 433.92 MHz
Range: 200 m in free field
Operating temperature: -10°C to +50°c
CR2032 3V 230 mAh lithium battery
Dimensions: H=72 mm x L=38 mm x D=16 mm
Weight: 27 g
Myfox S.A.S.
Regent Park II – Bât 1
Rue du Lac
31 670 - Labège - FRANCE
© MyFOX. All rights reserved.
140409 – v1.6
Internet user interface
GB
DE
IT
ES
NL
EMAIL: contact@myfox.fr
HOTLINE: +33 5 61 00 07 11
When sorting your waste, please observe the
disposal regulations in force. Please place waste in
the facilities provided for that purpose and with all due
respect for the environment.
Note: Replacing the batteries with the wrong type of
battery will cause a risk of explosion. Dispose of used
batteries in accordance with instructions.
Myfox declares that this product complies with the
essential requirements of R&TTE Directive
1999/5/EC. A full version of the declaration of
compliance is available from www.myfox.fr/certificats
3. Replacing the battery
Open the battery hatch at the back of the remote control by sliding the hatch
downwards. Remove the used battery and insert the new one. Simply push it into
the battery slot provided. Reposition the hatch by sliding it upwards.
5
1 3
4
2
6
Partial arming
Press this button to arm your unit in
partial mode (only some of the
intrusion detectors are active).
1
Total arming
Press this button to arm your unit in
total mode (all of the intrusion
detectors are active).
2
Auxiliary key
Press this button to trigger the auxiliary
function programmed on your main unit
(panic alert or scenario).
3
Disarming
Press this button to disable the
protection of all the intrusion detectors. If
the siren has been triggered, press this
button to stop it.
4
Operation LED
This LED flashes to confirm that a signal
has been sent to the main unit.
5
Battery hatch
The remote control uses a lithium
battery. Its battery life is three years,
assuming two activations per day.
6
1. Description
EN
  • Page 1 1

Myfox 4 Buttons Remote Control User manual

Myfox
Brand
Myfox
Model
4 Buttons Remote Control
Category
Remote controls
Type
User manual

Myfox 4 Buttons Remote Control

The Myfox 4 Buttons Remote Control allows you to easily and conveniently control your Myfox security system. With its four buttons, you can:

  • Arm your system in partial mode (only some of the intrusion detectors are active).
  • Arm your system in total mode (all of the intrusion detectors are active).
  • Disarm your system and stop the siren if it has been triggered.
  • Trigger the auxiliary function programmed on your main unit (panic alert or scenario).
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Other documents