Wireless
150N UsB
MiNi
AdApter
User
MANUAl
MODEL 524773
INT-524773-UM-1009-01
2
INTRODUCTION
Thank you for purchasing the INTELLINET NETWORK SOLUTIONS
™
Wireless
150N USB Mini Adapter, Model 524773.
This ultra-compact high-speed adapter lets you connect your notebook or desktop
PC to wireless networks faster than ever before, with link speeds of up to 150 Mbps.
This adapter is also compatible with 802.11b and 802.11g wireless access points
and wireless routers, giving you the exibility to start upgrading your wireless
network without the need to replace your existing equipment.
The easy-to-follow instructions in this user manual help make setup and operation
relatively simple, so you’ll soon be enjoying the benets of these additional features:
• Supports WMM (Wi-Fi Multimedia) for increased multimedia data throughput
• Supports WEP (64/128 bit), WPA and WPA2 data encryption
• Supports Cisco CCX
• Supports the most popular operating systems: Windows XP, Vista and 7
• Supports Hi-Speed USB 2.0/1.1 interface
• Supports Software AP (turns your wireless client into a wireless access point)
• Lifetime Warranty
NOTE: For a quick install procedure, refer to the printed quick install guide enclosed
with this product.
3
CONTENTS
CoNteNts
sAfety & CoMpliANCe stAteMeNts
Federal Communications Commission (FCC) Statements
FCC PART 15
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of Federal Communications Commission (FCC)
Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged to
try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment to an outlet on a circuit different from the receiver.
• Consult the dealer or an experienced radio/TV technician for help.
1 INSTALLATION ...............................................................................................5
1.1 Installing the Driver and Utility ................................................................5
1.2 Connecting to a Wireless Access Point ..................................................7
2 CONFIGURATION UTILITY ..........................................................................10
2.1 General ............................................................................................... 11
2.2 Prole ...............................................................................................12
2.3 Available Network ................................................................................16
2.4 Status ...............................................................................................17
2.5 Statistics ...............................................................................................18
2.6 Wi-Fi Protected Setup ..........................................................................18
2.6.1 Network Setup Using PIN Input Cong ..................................18
2.6.2 Network Setup Using Push Button Cong .............................20
2.7 SoftAP ...............................................................................................21
2.7.1 AP General / Properties Settings ...........................................21
2.7.2 AP Advanced ..........................................................................22
2.7.3 AP Statistics ...........................................................................24
2.7.4 ICS .........................................................................................24
3 SPECIFICATIONS .........................................................................................25
4
REGUL ATORY STATEM ENTS
FCC CAUTION
This device and its antenna must not be co-located or operated in conjunction with
any other antenna or transmitter.
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that
may cause undesired operation.
Any changes or modications not expressly approved by the party responsible for
compliance could void the authority to operate equipment.
FCC RADIATION EXPOSURE STATEMENT
This EUT complies with SAR for general population / uncontrolled exposure limits in
ANSI/IEEE C95.1-1999 and has been tested in accordance with the measurement
methods and procedures specied in OET Bulletin 65 Supplement C. The version
marketed in the U.S. is restricted to usage of channels 1 through 11.
R&TTE Compliance Statement
This equipment complies with all the requirements of Directive 1999/5/EC of the
European Parliament and the Council of March 9, 1999, on radio equipment and
telecommunication terminal equipment and the mutual recognition of their conformity
(R&TTE). The R&TTE directive repeals and replaces Directive 98/13/EEC
(Telecommunications Terminal Equipment and Satellite Earth Station Equipment)
as of April 8, 2000.
SAFETY
This equipment is designed with the utmost care for the safety of those who install
and use it. However, special attention must be paid to the dangers of electric shock
and static electricity when working with electrical equipment. All guidelines must,
therefore, be followed at all times to ensure the safe use of the equipment.
EU COUNTRIES INTENDED FOR USE
T
he ETSI version of this device is intended for home and ofce use in Austria,
Belgium, Denmark, Finland, France, Germany, Greece, Ireland, Italy, Luxembourg,
the Netherlands, Portugal, Spain, Sweden and the United Kingdom. The ETSI
version of this device is also authorized for use in EFTA member states Iceland,
Liechtenstein, Norway and Switzerland.
EU COUNTRIES NOT INTENDED FOR USE
None.
5
INSTA LL ATION
1 iNstAllAtioN
NOTE: The following installation represents Windows XP procedures and screen
images, but both are similar for Windows 2000, Vista and 7. Some screen images
have been modied to t the format of this manual.
Prior to installation, un-install any previously installed versions of this adapter’s
driver or utility.
1.1 Installing the Driver and Utility
1 . Insert the included setup/installation CD into your CD-ROM drive and run the
“Setup.exe” program.
2. When the Choose Setup
Language screen displays,
highlight your preference
a nd click “Next” to proceed.
3. When the rst of the Driver
and Utility screens displays,
click “Next.”
INTELLINET NETWORK SOLUTIONS
INTELLINET NETWORK SOLUTIONS
INTELLINET NETWORK SOLUTIONS Wireless
150N USB Mini Adapter Driver and Utility
The InstallShield Wizard will install the INTELLINET
NETWORK SOLUTIONS Wireless 150N USB Mini
Adapter Driver and Utility on your computer. To
continue, click “Next.”
6
INSTA LL ATION
4. When the next screen
displays, click “Install” to
begin the installation. On
any of the screens where
they appear, click “Back” to
return to a previous screen;
click “Cancel” to exit the
w i z a r d .
5. The Setup Status screen
will display, presenting a
status bar that indicates the
progress of the installation.
6. When the InstallShield
Wizard Complete screen
displays, click “Finish.”
INTELLINET NETWORK SOLUTIONS
INTELLINET NETWORK SOLUTIONS
INTELLINET NETWORK SOLUTIONS
7
INSTA LL ATION
1.2 Connecting to a Wireless Access Point
1 . To begin the adapter conguration by
connecting to a wireless AP, double-click
the utility icon in the system tray (or right-
click the one that automatically appears on
the desktop), then select the “Open Cong
Utility” option from the popup menu.
2. When the Utility screen
displays, click on the
Available Network menu
tab, then double-click the
wireless access point you
want to connect to from
among those that appear
in the Available Network(s)
table, as shown at right.
3. When the Wireless Network
Properties screen displays,
enter your security settings
and click “OK” to initiate the
network connection.
INTELLINET NETWORK SOLUTIONS Wireless 150N USB Mini Adapter Utility
8
INSTA LL ATION
Windows Zero Conguration Option for Vista
Windows Vista users can connect to a wireless access point using the Windows
Zero Conguration option.
1. Go to Start, then
Control Panel on
the desktop, then
select Network and
Internet.
2. With the Network
and Internet screen
displayed, select
“Connect to a
network” under the
Network and
Sharing Center
heading.
9
INSTA LL ATION
3. Highlight the access
point you want to
use (if it’s shown),
then click “Connect.”
4 . If it’s an unnamed
access point (i.e.,
the SSID of the
wireless AP is
hidden), you’ll be
prompted to input
its name, which
must be entered
exactly — without
error or deviation —
in order to make a
valid connection.
5 . If the access point
is protected by an
encryption method,
you need to input
its security code or
passphrase here.
As with the SSID, it
must match the
encryption setting
exactly. (Typically,
you would obtain it
from the AP’s
administrator.)
10
CONfIGURATION
6 . Once the message
“Successfully
connected...”
(between your
computer and the
wireless AP you
selected) displays,
click “Close” to start
the network
connection.
2 CoNfigUrAtioN Utility
The Conguration Utility is a powerful application that helps you congure the
Wireless 150N USB Mini Adapter and monitor the link status and the statistics
during the communication process. The utility appears as an icon in the system
tray and on the desktop of Windows. You can open it by double-clicking the desktop
icon. Right-click the icon in the system tray and an options menu displays.
Open Cong Utility: Select to open the conguration utility.
About: Select to display utility information.
Hide: Select to hide the utility in the system tray.
Quit: Select to quit the utility in the system tray.
The Conguration Utility opens to the General screen, with another ve tabs near
the top of the screen you can select for specic conguration options. Whichever
of the tabs you select, several additional options are always displayed at the top,
left and bottom of the screen, as shown on the General screen in the rst of the
detailed sections that follow.
Above: utility system tray icon.
Right: utility options menu.
11
CONfIGURATION
Refresh: This updates the adapter list in the left-side window.
Mode: This allows you to select one of two modes: Station or Access Point.
• With Station, the adapter works as a wireless adapter.
• With Access Point, the adapter works as a wireless AP. (See SoftAP.)
View: This allows you to enable “Status Bar,” which will display the current status
of the utility at the bottom of the screen.
About: This lets you check the version of the utility.
Show Tray Icon: Select to show the utility icon in the system tray.
Radio Off: Select to turn off or turn on the radio of the adapter. If the radio is
turned off, the adapter will not work.
Disable Adapter: This allows you to disable or enable the adapter.
Windows Zero Cong: Select to congure the adapter using Windows XP Zero
Conguration.
2.1 General
This screen is primarily for checking connection-related items and information
about the selected adapter, some of which — Status, Speed, Signal Strength,
INTELLINET NETWORK SOLUTIONS Utililty
INTELLINET NETWORK SOL
HiMom
12
CONfIGURATION
Link Quality and Network Address — are self-explanatory. The other references on
this screen reect the settings congured on the Prole screen.
Type: This displays either “Infrastructure” (operating in conjunction with an access
point) or “Ad Hoc” (operating without an access point) based on the selection
made on the Prole screen.
Encryption: This displays the encryption setting of the current connection —
“None,” “WEP,” “TKIP” or “AES” — based on the selection made on the Prole
screen.
SSID: The Service Set ID (up to 32 printable ASCII characters) is the unique name
identied in a WLAN that prevents the unintentional merging of two co-located
wireless networks. This can be entered on the Prole screen.
Renew IP: Click to renew the IP address of the adapter.
2.2 Prole
This screen helps you manage the networks you connect to frequently. By creating
and using proles, you can avoid the need to re-establish settings each time you
make a connection.
INTELLINET NETWORK SOLUTIONS Utililty
INTELLINET NETWORK SOL
13
CONfIGURATION
Available Prole(s): This list shows the preferred networks for the wireless
connection. You can add, remove, edit and duplicate the preferred networks,
and you can also set one of the networks as the default connection.
Add/Remove/Edit: Click with a prole selected to make desired changes.
Duplicate: Click to create a new prole with the same settings as the current one.
Set Default: Click to designate a selected prole on the Available Prole(s) list as
the default network.
CONFIGURING A PROFILE
Clicking “Add” or “Edit” on the Prole screen will display a Wireless Network
Properties screen that allows you to set various parameters required to be in
synch with devices you connect to wirelessly.
Prole Name: Enter an easily recognizable name to quickly differentiate among
multiple networks.
Network Name (SSID): The SSID (up to 32 printable ASCII characters) is the
unique name identied in a WLAN. The ID prevents the unintentional merging
of two co-located WLANs. If you specify an SSID for the adapter, then only the
device with the same SSID can connect to the adapter.
This is a computer-to-computer (ad hoc) network; wireless access points
are not used.: When this option is selected, the adapter will operate in Ad Hoc
14
CONfIGURATION
mode (connecting to another wireless adapter in the WLAN without an access
point or router) vs. Infrastructure mode (which connects through an AP or router).
Channel: This setting is only available for Ad Hoc mode. Select the radio channel
used for the network you’re connecting to.
Network Authentication: This setting needs to be consistent with the wireless
networks the adapter is intended to be connected to. There are seven options.
• Open System means that no authentication is needed within the wireless
network.
• Shared Key means that only wireless stations using a shared key (WEP Key
identied) are allowed to connect to each other.
• WPA-PSK is a special mode designed for home and small business users
who don’t have access to network authentication servers. In this mode, also
known as Pre-Shared Key, the user manually enters the starting password in
her access point or gateway, as well as in each wireless station in the network.
WPA-PSK takes over automatically from that point, keeping unauthorized
users who don’t have the matching password from joining the network while
encrypting the data traveling between authorized devices.
• WPA2-PSK is also for homes and small businesses. It differs from WPA-PSK
in that it provides data encryption via the Advanced Encryption Standard (AES).
In contrast, WPA-PSK uses the Temporal Key Integrity Protocol (TKIP).
• WPA 802.1X (or just WPA) provides a scheme of mutual authentication using
either IEEE 802.1x / Extensible Authentication Protocol (EAP) authentication
or pre-shared key (PSK) technology. It provides a high level of assurance to
enterprises, small businesses and home users that data will remain protected
and that only authorized users may access their networks. For enterprises
that have already deployed IEEE 802.1x authentication, WPA offers the
advantage of leveraging existing authentication databases and infrastructure.
• WPA2 802.1X, like WPA, supports IEEE 802.1x / EAP authentication or PSK
technology. It also includes a new advanced encryption mechanism using the
Advanced Encryption Standard (AES). AES is required for corporate and
government users. The difference between WPA and WPA2 is that WPA2
provides data encryption via the AES, whereas WPA uses the Temporal Key
Integrity Protocol (TKIP).
• WEP 802.1X is a special mode for using IEEE 802.1x / EAP technology for
authentication and WEP keys for data encryption.
Data Encryption: All devices in the network should use the same encryption
method. The drop-down menu offers four options.
• Disabled disables the WEP data encryption.
• WEP enables the WEP data encryption. When this is selected, you need to
continue with the setting of the WEP encryption keys.
15
CONfIGURATION
• TKIP (Temporal Key Integrity Protocol) changes the temporal key every
10,000 packets. (A packet is a kind of message transmitted over a network.)
This ensures much greater security than standard WEP security.
• AES has been developed to ensure the highest degree of security and
authenticity for digital information. It’s the most advanced solution dened by
IEEE 802.11i for security in the wireless network.
ASCII / PASSPHRASE: WEP key entries can be in ASCII or passphrase format.
• ASCII uses alphanumeric values or signs, making it more easily recognizable
for users.
• PASSPHRASE entries require a text string with a maximum of 32 alphanumeric
characters; for example, “Test.” The same passphrase or WEP key settings
must be used for all wireless computers within the network. NOTE: Due to
possible incompatibility with other manufacturers’ passphrase generators, a
passphrase may not work with other product brands.
Key Length: When “WEP” and “PASSPHRASE” are selected, this option displays.
• 64-bit lets you input 10-digit hexadecimal values as the encryption keys; for
example, “0123456aef.”
• 128-bit lets you input 26-digit hexadecimal values as the encryption keys; for
example, “01234567890123456789abcdef.”
Key Index (advanced): Select one of the four keys to be the data encryption key.
Network Key: Enter the network security key here to make sure the password is
correct.
Conrm Network Key: Enter the network security key again.
EAP Type: The Extensible Authentication Protocol drop-down menu offers four
options.
• GTC is an authentication protocol that allows the exchange of clear text
authentication credentials across the network.
• TLS is the most secure of the EAP protocols, but isn’t easy to use. It requires
that digital certicates be exchanged in the authentication phase. The server
presents a certicate to the client and, after validating the server’s certicate,
the client presents a client certicate to the server for validation.
• LEAP is a pre-EAP, Cisco-proprietary protocol with many of the features of
EAP protocols. Cisco controls the ability of other vendors to implement this
protocol, so it should be selected for use only when limited brand choice for
client, access-point and server products is not a concern. Once you’ve set up
LEAP authentication, you need to enter the username and password of your
computer.
• PEAP & TTLS are similar to, yet easier than, TLS in that they specify a stand-
alone authentication protocol be used within an encrypted tunnel. TTLS
supports any protocol within its tunnel, including CHAP, MSCHAP, MSCHAPv2
16
CONfIGURATION
and PAP. PEAP species that an EAP-compliant authentication protocol must
be used; this adapter supports MD5, TLS, GTC (Generic Token Card) and
MSCHAPv2. That a client certicate be required for authentication is optional.
Tunnel: Options are MD5, GTC, TLS and MSCHAP-v2.
Username: This is the certicate username on the RADIUS server.
Identity: This is the user’s identity on the RADIUS server.
Password: This is the user’s password on the RADIUS server.
Certicate: Select the certicate for RADIUS server authentication.
2.3 Available Network
When you open the Conguration Utility, the system will scan all the channels to
nd all the access points/stations within the accessible range of your adapter, then
automatically connect to the wireless network with the highest signal strength. On
this screen, you can see all the nearby networks listed and you can change the
connection to another network.
INTELLINET NETWORK SOLUTIONS Utililty
INTELLINET NETWORK SOL
17
CONfIGURATION
Available Network(s): This list presents important connection information about
the available wireless networks within the range of your adapter. To connect to
any network on the list, highlight it and double-click.
Refresh: Click to update the Available Network(s) list. It is recommended that the
list be refreshed anytime a different network is selected.
Add to Prole: Click to add the selected network to a prole so you can connect
to a previously joined network quicker (see 2.2 Prole).
2.4 Status
This screen shows information about the manufacturer, driver version, settings of
the wireless network the adapter is connecting to (helpful if you don’t know this
when you’re trying to establish a connection), linking time and link status.
INTELLINET NETWORK SOLUTIONS Utililty
INTELLINET NETWORK SOL
INTELLINET NETWORK SOLUTIONS
INTELLINET
18
CONfIGURATION
2.5 Statistics
You can get the real-time information about packet transmissions and the receiving
status during wireless communications from this screen. To update the statistics
values, click “Reset.”
2.6 Wi-Fi Protected Setup (WPS)
Wi-Fi Protected Setup (WPS) is the latest wireless network technology and makes
wireless network setup very simple. If you have a WPS-enabled wireless access
point and you want to establish a secure connection to it, you don’t have to
congure the wireless access point and set up data encryption all by yourself. All
you need to do is go to this screen, click either “PBC” or “PIN,” then — on the
wireless access point you want to connect to — either press the WPS button on
the AP’s chassis or enter the eight-digit code found here on the adapter’s
Conguration Utility Wi-Fi Protected Setup screen.
2.6.1 NETWORK SETUP USING PIN INPUT CONFIG (PIN)
1. Enter the PIN code of your wireless adapter (displayed right above the “PIN”
button — see image below) on the wireless access point you want to connect to.
If necessary, refer to the user manual of the wireless AP for instructions.
INTELLINET NETWORK SOLUTIONS Utililty
INTELLINET NETWORK SOL
19
CONfIGURATION
2. Click “Pin Input Cong (PIN)” and the prompt at
right will display. Click “Yes” to select a specic
wireless access point or click “No” to start the
PIN method of WPS.
3. If you click “Yes,” the prompt at right
will display. Select the wireless AP
name you want to connect to and
click “Select.”
INTELLINET NETWORK SOLUTIONS Utililty
INTELLINET NETWORK SOL
20
CONfIGURATION
4. A Status screen will display
to indicate the progress of
the procedure, which can
take up to two minutes or
so. If a wireless access point
with the correct PIN code is
found, you’ll be connected
to it.
2.6.2 NETWORK SETUP USING PUSH BUTTON CONFIG (PBC)
1. Begin the PBC pairing procedure by setting up the access point. Refer to the
user manual of the wireless AP for instructions. Click “Push Button Cong (PBC)”
on the Wi-Fi Protected Setup screen to begin the wireless connection using
WPS. This procedure can take up to a minute to complete.
2. Once a successful WPS connection has been made between the wireless
adapter and the access point, details about the connected access point will be
displayed (as shown below).
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
/