Sharp FV-DB1E Quick start guide

Brand: Sharp

Model: FV-DB1E

Type: Quick start guide

Connect the AC adaptor

Insert the memory batteries

This Quick Start Guide will help you to correctly install and operate your system.

If you require any advice or assistance regarding

your Sharp product, please visit our web-site

www.sharp.co.uk/customersupport.

Customers without Internet access may telephone

08705 274277 during office hours (or (01) 676 0648

if telephoning from Ireland).

0301

Accessories

Memory batteries maintain the clock setting and preset stations for

the tuner.

TINSEA026SJZZ

04D N AO 1

Turning on your unit

Press the ON/STAND-BY button to turn the power on.

When turned on for the first time, the unit scans radio sta-

tions automatically to create the station list.

After the scan:

The stations will be stored in alphanumeric order and the first

station on the list will be selected and you will hear it through

the speaker.

MODEL

FV-DB1E

DAB RECEIVER

AC adaptor × 1

(RADPAA001SJZZ)

“AA” size battery

(UM/SUM-3, R6, HP-7

or similar) × 2

1Open the battery compartment.

2Insert the supplied 2 “AA” size batteries (UM/SUM-3, R6, HP-

7 or similar) into the battery compartment.

3Close the battery compartment.

Plug the AC adaptor into the wall socket, and then insert the

plug on the other end into the DC 9V socket.

Wall socket

(AC 230 - 240V 50/60 Hz)

To the DC 9V socket

Adjusting the volume

Press the VOLUME (+ or -) button to increase or decrease the

volume.

21 39 40

.....

FV_DB1E_QG.pm 04.4.12, 6:40 PM1

Downloaded from: http://www.usersmanualguide.com/

Listening to the DAB Listening to the FM

1Press the BAND button until “FM” appears on the

display.

2Press the TUNING ( or ) button to tune in to the desired

station.

When the TUNING button is pressed for 2 seconds or more,

scanning will start automatically and the tuner will stop at the

first receivable broadcast station.

To receive an FM stereo transmission:

Press the BAND button to display the “ST” indicator.

“” will appear when an FM broadcast is in stereo.

FM stereo mode indicator

FM stereo receiving indicator

If trouble occurs

When this product is subjected to strong external interference

(mechanical shock, excessive static electricity, abnormal supply

voltage due to lightning, etc.) or if it is operated incorrectly, it may

malfunction.

If such a problem occurs, do the following:

1. Set the unit to the stand-by mode and turn the power on

again.

2. If the unit is not restored in the previous operation, unplug

and plug in the AC adaptor from the wall socket and re-

place the main batteries, memory batteries and then turn

the power on.

Caution:

This operation will erase all data stored in memory including clock,

alarm settings, tuner preset, and station list, etc.

Clearing all the memory (reset)

1. Press the ON/STAND-BY button to enter the stand-by mode.

2. Whilst pressing down the PRESET 1 button and the

PRESET SELECT button, press the ON/STAND-BY button

until “All clear ok?” appears.

3. Within 30 seconds, press the ENTER button.

“Complete” appears and the memory is cleared.

Caution:

This operation will erase all data stored in memory including clock,

alarm settings, tuner preset, and station list, etc.

Maintenance

Routine maintenance is required for continued optimum perfor-

mance, refer to the operation manual (page 19).

TINSEA026SJZZ

Retuning the unit (Auto tune)

You can retune the radio when you move the unit to other areas or

add multiplex channels to the station list.

There are two Auto tune options available.

Autotune UK:

All frequencies are scanned in the UK channel allocation.

This may take a few seconds.

Autotune Full:

The full range of digital frequencies is scanned in Band III.

This may take a minute or more.

1Press the BAND button until “DAB” appears on the

display.

2Autotune UK:

Press the AUTO TUNE button for less than 1 second.

Autotune Full:

Hold down the AUTO TUNE button for 2 seconds or more.

Selecting a station in the station list

Once a DAB station is received, you can select stations in the

station list.

1Press the BAND button until “DAB” appears on the

display.

2Whilst receiving a DAB station, press the TUNING ( or

) button repeatedly to select the desired station.

The upper part of the display shows the current station name,

and the name of the station being scanned (with “ ”) ap-

pears in the lower part.

3Within 30 seconds, press the ENTER button.

The current station name

The name of the station being

scanned

FV_DB1E_QG.pm 04.4.12, 6:40 PM2

Downloaded from: http://www.usersmanualguide.com/

This file has been downloaded from:

www.UsersManualGuide.com

User Manual and User Guide for many equipments like mobile phones, photo cameras, monther board, monitors, software, tv, dvd, and othes..

Manual users, user manuals, user guide manual, owners manual, instruction manual, manual owner, manual owner's, manual guide,

manual operation, operating manual, user's manual, operating instructions, manual operators, manual operator, manual product,

documentation manual, user maintenance, brochure, user reference, pdf manual

Downloaded from: http://www.usersmanualguide.com/

Sharp FV-DB1E Quick start guide

Sharp FV-DB1E Quick start guide

Sharp FV-DB1E Quick start guide

Related papers

Other documents