Makeblock Smart Target Building Instructions

Makeblock
Brand
Makeblock
Model
Smart Target
Type
Building Instructions
Building Instructions
Smart Target
Take out the wood boards you need.
1
2
Pro tips
Use the sandpaper included to sand
a smooth finish on the wood board
before you start installing it.
Assemble the wood boards as shown.
Attach a rubber band.
3
Slot in the wood boards as shown and hold them in place with rubber bands.
4
Adjust the servo hub.
Attach a rubber band.
One more to attach.
Attach a rubber band.
Turn the servo hub clockwise all
the way down to the bottom.
Turn the servo hub's opening to the
side of the servo with a ring mark.
Attach a
rubber band.
6
Slot in the wood board as shown and secure it with rubber bands.
Install the servo.
5
Front (with marks)
Back (without
marks)
Make sure you correctly identify the
front and back sides. The front side
has marks while the back side has
no marks.
Rotate
Flip
The marked
side faces up.
Place the servo on
the wood board.
2
Pass the servo cable
through the opening
as shown.
1
M3 *14mm
1:1
Tighten the studs.
Attach a rubber band.
Attach a rubber band.
Attach a
rubber band.
7
Install Halocode.
8
10 cm
20 cm
Align the holes on the acrylic board
and wood board, then push the big
head rivets through the holes, and
press them all the way down.
Tighten the stud.
Do the same with the rest of
the screws and studs.
Peel off the protective
film on both sides.
M3 *14mm
1:1
9
10
Add the LED matrix.Use rubber bands to secure the Halocode-embedded disc to the stand.
Make sure the Micro USB port on Halocode faces down.
Micro USB port
faces down.
Hook four rubber bands
around the four big head
rivets and the four corners
on the stand.
11
Insert a 10 cm connection cable and a 20 cm connection
cable into the ports of the power module.
Install the power module.
12
Connect the power module and
LED matrix.
13
10 cm
20 cm
20 cm
10 cm
Thread the connection
cable through the hole.
1
Insert the connection
cable into the LED
matrix.
2
Insert a 10 cm connection cable
into the servo driver.
16
14
Take out the servo driver. Connect the
power module to the servo driver as
shown.
15
Insert the servo cable into the servo
driver.
Fix the servo driver to the power
module.
17
20 cm
10 cm
Take out the speaker and connect
the servo driver to the speaker as
shown.
18
Connect Halocode and the speaker.
19
Install the speaker.
20
22 23
Remove these wood boards from the sheet.
21
Attach a rubber band.
Rotate Rotate
Attach a rubber band.
24 25
Attach a rubber band.
Attach a rubber band.
Wow! You’ve made it!
27
26
Rotate
Flip
Attach a rubber band.
Attach a rubber band.
Attach a rubber band.
2
3
1
Now, return to mBlock on your PC or iPad and program your project.
28
mBlock
https://hezi.makeblock.com
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13

Makeblock Smart Target Building Instructions

Makeblock
Brand
Makeblock
Model
Smart Target
Type
Building Instructions
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Other documents