DC146
Micro Hi-Fi System
User manual
Register your product and get support at
www.philips.com/welcome
Pg001-pg021_DC146_79_Eng 3/30/10, 17:591
2
CAUTION
Use of controls or adjustments or
performance of procedures other
than herein may result in hazardous
radiation exposure or other unsafe
operation.
Pg001-pg021_DC146_79_Eng 3/30/10, 17:592
3
Pg001-pg021_DC146_79_Eng 3/30/10, 17:593
4
English
Contents
General Information
Supplied accessories ............................................ 5
Environmental Information ................................ 5
Safety Information ............................................ 5~6
Hearing Safety ....................................................... 6
Preparations
Rear connections ................................................. 7
Inserting batteries into the Remote Control 8
Using the Remote Control to operate
the system .............................................................. 8
Controls
Controls on the system and remote control 9
Controls available on the remote
control only ........................................................... 9
Basic Functions
Switching the system on ................................... 10
Power-saving automatic standby ..................... 10
Adjusting volume and sound ............................ 10
CD Operation
Loading a disc ...................................................... 11
Basic playback controls ..................................... 11
Different play modes: SHUFFLE and REPEAT
12
Programming track numbers ........................... 12
Reviewing the programme ............................... 12
Erasing the programme ..................................... 12
Radio Reception
Tuning to radio stations .................................... 13
Programming radio stations ............................. 13
Automatic programming
Manual programming
Tuning to preset radio stations ....................... 13
iPod
Playing iPod using the dock .............................. 14
Compatible dock adaptors
Dock adaptor
Playing iPod
Charging iPod battery using the dock ........... 14
Clock/Timer
Setting the clock ................................................. 15
Setting the timer................................................. 15
Activating and deactivating TIMER ................. 15
Activating and deactivating SLEEP .................. 15
Specifications ........................................... 16
Maintenance.............................................. 16
Tr oubleshooting ............................. 17~18
Pg001-pg021_DC146_79_Eng 3/30/10, 17:594
English
5
General Information
Congratulations on your purchase and welcome
to Philips!
To fully benefit from the support that Philips
offers, register your product at www.philips.com/
welcome.
Supplied accessories
–2 speaker boxes
– remote control
–4 x dock adaptors
Environmental Information
All unnecessary packaging has been omitted. We
have tried to make the packaging easy to
separate into three materials: cardboard (box),
polystyrene foam (buffer) and polyethylene (bags,
protective foam sheet).
Your system consists of materials which can be
recycled and reused if disassembled by a
specialized company. Please observe the local
regulations regarding the disposal of packaging
materials, exhausted batteries and old
equipment.
Disposal of your old product
Your product is designed and manufactured with
high quality materials and components, which
can be recycled and reused.
When this crossed-out wheeled
bin symbol is attached to a
product it means the product is
covered by the European
Directive 2002/96/EC
Please inform yourself about the
local separate collection system for electrical and
electronic products.
Please act according to your local rules and do
not dispose of your old products with your
normal household waste. The correct disposal of
your old product will help prevent potential
negative consequences for the environment and
human health.
Notes for battery disposal
Your product contains batteries covered by the
European Directive 2006/66/EC, which cannot
be disposed of with normal household waste.
Please inform yourself about the local rules on
separate collection of batteries. The correct
disposal of batteries helps prevent potentially
negative consequences on the environment and
human health.
Safety Information
● Before operating the system, check that the
operating voltage indicated on the typeplate (or
the voltage indication beside the voltage
selector) of your system is identical with the
voltage of your local power supply. If not, please
consult your dealer.
● Place the system on a flat, hard and stable
surface.
● Where the MAINS plug or an appliance coupler
is used as the disconnet device, the disconnet
device shall remain readily operable.
● The apparatus shall not be exposed to
dripping or splashing.
● Install the unit near the AC outlet and where the
AC power plug can be easily reached.
● Place the system in a location with adequate
ventilation to prevent internal heat build-up in
your system. Allow at least 10 cm (4 inches)
clearance from the rear and the top of the unit
and 5 cm (2 inches) from each side.
● The ventilation should not be impeded by
covering the ventilation openings with items,
such as newspapers, table-cloths, cur tains, etc.
● Do not expose the system, batteries or discs to
excessive moisture, rain, sand or heat sources
caused by heating equipment or direct sunlight.
● No naked flame sources, such as lighted candles,
should be placed on the apparatus.
● No objects filled with liquids, such as vases, shall
be placed on the apparatus.
● If the system is brought directly from a cold to a
warm location, or is placed in a very damp room,
moisture may condense on the lens of the disc
unit inside the system. Should this occur, the CD
player would not operate normally. Leave the
power on for about one hour with no disc in the
system until normal playback is possible.
Pg001-pg021_DC146_79_Eng 3/30/10, 17:595
6
English
General Information
● The mechanical parts of the set contain self-
lubricating bearings and must not be oiled or
lubricated.
● When the system is switched to Standby
mode, it is still consuming some power.
To disconnect the system from the
power supply completely, remove the AC
power plug from the wall socket.
Hearing Safety
Listen at a moderate volume.
● Using headphones at a high volume can impair
your hearing. This product can produce sounds
in decibel ranges that may cause hearing loss for
a normal person, even for exposure less than a
minute. The higher decibel ranges are offered
for those that may have already experienced
some hearing loss.
● Sound can be deceiving. Over time your hearing
"comfort level" adapts to higher volumes of
sound. So after prolonged listening, what sounds
"normal" can actually be loud and harmful to
your hearing. To guard against this, set your
volume to a safe level before your hearing
adapts and leave it there.
To establish a safe volume level:
● Set your volume control at a low setting.
● Slowly increase the sound until you can hear it
comfortably and clearly, without distortion.
Listen for reasonable periods of time:
● Prolonged exposure to sound, even at normally
"safe" levels, can also cause hearing loss.
● Be sure to use your equipment reasonably and
take appropriate breaks.
Be sure to observe the following
guidelines when using your headphones.
● Listen at reasonable volumes for reasonable
periods of time.
● Be careful not to adjust the volume as your
hearing adapts.
● Do not turn up the volume so high that you
can't hear what's around you.
● You should use caution or temporarily
discontinue use in potentially hazardous
situations.
● Do not use headphones while operating a
motorized vehicle, cycling, skateboarding, etc.; it
may create a traffic hazard and is illegal in many
areas.
Pg001-pg021_DC146_79_Eng 3/30/10, 17:596
English
7
Preparations
Rear connections
The type plate is located at the rear of the
system.
A Power
– Before connecting the AC power cord to the
wall outlet, ensure that all other connections
have been made.
WARNING!
–For optimal performance, use only the
original power cable.
–Never make or change any connections
with the power switched on.
To avoid overheating of the system, a safety
circuit has been built in. Therefore, your
system may switch to Standby mode
automatically under extreme conditions. If
this happens, let the system cool down
before reusing it (not available for all versions).
speaker
(right)
speaker
(left)
FM wire antenna
AC power cord
A
B
B Speakers Connection
Front Speakers
Connect the speaker wires to the SPEAKERS
terminals, right speaker to "RIGHT" and left
speaker to "LEFT", red wire to "+" and black
wire to "-".
● Fully insert the stripped portion of the speaker
wire into the terminal as shown.
Notes:
–For optimal sound performance, use the supplied
speakers.
– Do not connect more than one speaker to any
one pair of +/- speaker terminals.
– Do not connect speakers with an impedance
lower than the speakers supplied. Please refer to
the SPECIFICATIONS section of this manual.
1
2
Pg001-pg021_DC146_79_Eng 3/30/10, 17:597
8
English
Inserting batteries into the
Remote Control
1 Open the battery compartment.
2 Insert two R03 or AAA batteries following the
indications (+/-) inside the compartment.
3 Close the cover.
3
1
2
Using the Remote Control to
operate the system
1 Aim the Remote Control directly at the remote
sensor (IR) on the front panel.
2 Do not put any objects between the Remote
Control and the system while operating the
system.
CAUTION!
– Remove batteries if they are
exhausted or if the Remote Control is
not being used for a long time.
– Do not use old and new or different
types of batteries in combination.
– Batteries contain chemical substances,
so they should be disposed of properly.
Preparations
Pg001-pg021_DC146_79_Eng 3/30/10, 17:598
English
9
Controls (illustrations on page 3)
Controls on the system and
remote control
1 STANDBY-ON2 (POWER)
– switches the system to standby or on.
2 iR SENSOR
– infrared sensor for remote control.
3 SOURCE
– selects the respective sound source for CD/iPod/
TUNER/AUX.
– switches on the system.
4 PRESET +/-
for radio .............. selects a preset radio station.
5 DOCK
– selects the iPod source.
6 TUNING 4 ¢
for Tuner ............. tunes to radio stations.
for CD/iPod ...... skips to the beginning of the
current/previous/subsequent
track.
................................. fast searches back and forward
within a track/CD.
for clock/timer adjusts the hours and minutes
for the clock/timer function
VOL +/-
– adjusts the volume level.
7 2;
– starts or interrupts CD playback.
8 REPEAT
– repeats a track/ disc/ all programmed tracks.
9 DBB (Dynamic Bass Boost)
– enhances the bass.
0 9
– stops CD playback or erases a CD programme.
! PUSH TO OPEN
– opens/closes the DOCK door.
@ PULL TO OPEN
– opens/closes the CD door.
AUX jack (located on the back panel)
– connects an external source (3.5 mm socket)
HEADPHONE (located on the back panel)
–connects headphones
Controls available on the remote
control only
# REP ALL
– repeats a track/disc /all programmed tracks.
$ SHUF
– plays CD tracks in random order.
% CLOCK/DISPLAY
– sets/views the clock.
^ TIMER/SLEEP
–Turns on or off timer/sets the timer function.
– activates/deactivates or selects the sleeper time.
& MENU
for iPod ............... enters iPod menu.
* 3 / 4
for iPod ............... navigates in iPod menu.
4 / ¢
for Tuner ............. tunes to radio stations.
for CD/iPod ...... skips to the beginning of the
current/previous/subsequent
track.
................................. fast searches back and forward
within a track/CD.
for clock/timer adjusts the hours and minutes
for the clock/timer function.
OK
for iPod ............... confirms menu selection.
( V OL +/-
– adjusts the volume level.
) MUTE
– interrupts and resumes sound reproduction.
¡ PROG
for CD ................. programmes tracks and reviews
the programme.
for Tuner ............. programmes tuner stations
manually or automatically.
Pg001-pg021_DC146_79_Eng 3/30/10, 17:599
10
English
Basic Functions
IMPORTANT:
Before you operate the system, complete
the preparation procedures.
Switching the system on
● Press STANDBY-ON 2 or SOURCE
(POWER on the remote control).
➜ The system will switch to the last selected
source.
● Press DISC, iPOD, TUN or AUX on the
remote control.
➜ The system will switch to the selected source.
To switch the system to standby mode
● Press STANDBY-ON 2 on the system (or
POWER on the remote control).
To switch the system to Eco-power
standby mode
● Press and hold STANDBY-ON (POWER on
the remote control) for more than 2 seconds.
➜ The backlight for clock display is dim.
Power-saving automatic standby
The power-saving feature automatically switches
to standby 15 minutes after a CD playback has
ended and no control is operated.
MICRO SYSTE M DC146
SOURC E
DOCK
DBB
STANDBY
-
ON
VOL
VOL
TUNING
REPEAT
CD/CD
-
R/CD
-
RW COMPATIBLE
PRESE T
iR
Adjusting volume and sound
1 Press VOL +/- to adjust volume.
➜ Display shows the volume level: VOL and a
number from 0-32.
2 Press DBB to switch bass enhancement on or
off.
➜ Display shows: if the DBB is activated.
3 Press MUTE on the remote
control to interrupt sound
reproduction instantly.
➜ Playback will continue
without sound.
● To activate sound
reproduction you can:
– press MUTE again;
– adjust the volume controls;
– change source.
MUTE
OK
Pg001-pg021_DC146_79_Eng 3/30/10, 17:5910
English
11
CD Operation
Basic playback controls
To play a disc
● Press 2; to start playback.
➜ The current track number and the PLAY icon
are displayed during disc playback.
To select a different track
● Press TUNING 4 ¢ (on the remote
control 4 / ¢) once or repeatedly until
the desired track number appears in the display.
To find a passage within a track
1 Press and hold down on TUNING 4 ¢
(on the remote control 4 / ¢).
➜ The disc is played at high speed and low
volume.
2 When you recognise the passage you want,
release TUNING 4 ¢ (on the remote
control 4 / ¢).
➜ Normal playback continues.
To interrupt playback
● Press 2; during playback.
➜ The display freezes and the PLAY icon flashes
when playback is interrupted.
➜ To resume, press 2; again.
To stop playback
● Press 9.
Notes: CD play will also stop when;
– the CD door is opened.
– the disc has reached the end.
– you select another source: TUNER, iPod or AUX.
– you select standby.
IMPORTANT:
The lens of the CD player should never be
touched.
Loading a disc
This CD player plays Audio Discs including CD-
Recordables and CD-Rewritables.
● CD-ROM, CD-I, CDV, MP3 CD, VCD, DVD or
computer CDs, however, are not possible.
1 Select CD source.
2 Lift the CD door on the top
of the system to open the CD
compartment.
➜ “OPEn” is displayed when
you open the CD
compartment.
3 Insert a disc with the printed side facing up and
press down on PULL TO OPEN to close the
CD door.
➜ “rEAd” is displayed as the CD player scans
the contents of a disc, and then the total number
of tracks is shown.
MICRO SYSTE M DC146
SOURC E
DOCK
DBB
STANDBY
-
ON
VOL
VOL
TUNING
REPEAT
CD/CD
-
R/CD
-
RW COMPATIBL E
PRESE T
iR
PULL TO OPEN
Pg001-pg021_DC146_79_Eng 3/30/10, 17:5911
12
English
CD Operation
Different play modes: SHUFFLE
and REPEAT
You can select and change the various play
modes before or during playback. The play
modes cannot be combined with
PROGRAMME.
SHUF ................ tracks of the entire disc are
played in random order.
REP ALL ...........repeats the entire disc/
programme.
REP ................... plays the current track
continuously.
1 To select Repeat play mode, press REPEAT on
the main unit or REP ALL on the remote
control.
● To select Shuffle play mode, press SHUF on the
remote control.
2 Press 2; to start playback if in the STOP
position.
3 To return to normal playback, press the
respective REPEAT (on the main unit), REP
ALL or SHUF (on the remote control) button
until the various SHUFFLE/ REPEAT modes are
no longer displayed.
● Press 9 once during playback to stop repeat/
shuffle playback.
● Press 9 again to cancel repeat/shuffle play mode.
Note:
– The SHUFFLE and REPEAT functions can be used
simultaneously.
Programming track numbers
Programme in the STOP position to select and
store your disc tracks in the desired sequence. If
you like, store any track more than once. Up to
20 tracks can be stored in the memory.
1 In the stop position, use the TUNING 4
¢ (on the remote control 4 / ¢) to
select your desired track number.
2 Press PROG to store.
➜ Display: PROG flashes, and 01 is displayed
briefly, then the selected track number.
3 Repeat steps 1-2 to select and store all desired
tracks.
4 To start playback of your disc programme, press
2;.
Reviewing the programme
● Stop playback and press PROG.
Erasing the programme
You can erase the programme by:
● pressing 9 once in the STOP mode;
● pressing 9 twice during playback;
● opening the CD compartment;
➜ PROG disappears from the display.
Pg001-pg021_DC146_79_Eng 3/30/10, 17:5912
English
13
Radio Reception
Tuning to radio stations
1 Press SOURCE on the set repeatedly or press
TUN on the remote control repeatedly until
the desired waveband (FM or MW) is displayed.
2 Press down on TUNING 4 ¢ (4 /
¢ on the remote control) and release the
button.
➜ The radio automatically tunes to a station
with sufficient reception. Display indication during
automatic tuning: SrcH .
3 Repeat step 2 if necessary until you find the
desired station.
● To tune to a weak station, press TUNING 4
¢ (4 / ¢ on the remote control)
briefly and repeatedly until you have found
optimal reception.
Programming radio stations
You can store up to a total of 20 radio stations
in the memory.
Automatic programming
Automatic programming will start with a chosen
preset number. From this preset number
upwards, former programmed radio stations will
be overridden. The system will only programme
stations which are not in the memory already.
1 Press PRESET
++
++
+/
--
--
- to select the preset
number where programming should start.
Note:
– If no preset number is selected, default is preset
(1) and all your presets will be overridden.
2 Press PROG. for more than 2 seconds to
activate programming.
➜ “AUtO” is displayed and available stations are
programmed in order of waveband reception
strength. The first preset automatically stored will
then be played.
Manual programming
1 Tune to your desired station (see Tuning to radio
stations).
2 Press PROG to activate programming.
➜ PROG flashes in the display.
3 Press PRESET
++
++
+/
--
--
- to allocate a number
from 1 to 20 to this station.
4 Press PROG again to confirm the setting.
➜ PROG disappears, the preset number and the
frequency of the preset station are shown.
5 Repeat the above four steps to store other
stations.
● You can override a preset station by storing
another frequency in its place.
Tuning to preset radio stations
● Press PRESET
++
++
+/
--
--
- until the desired preset
station is displayed.
MICRO SYSTE M DC146
SOURC E
DOCK
DBB
STANDBY
-
ON
VOL
VOL
TUNING
REPEAT
CD/CD
-
R/CD
-
RW COMPATIBLE
PRESE T
iR
Pg001-pg021_DC146_79_Eng 3/30/10, 17:5913
14
English
iPod
Playing iPod using the dock
This system is equipped with a dock used for
iPod. You can listen to the sound of the docked
player through the powerful speakers of the
system.
Compatible portable player
● Apple iPod models with 30-pin dock connector
as follows:
iPod classic, iPod touch, iPod nano, iPod 5th
generation (video), iPod with color display, iPod
mini.
Dock adaptor
Before plugging your player in the dock, snap the
suitable dock adaptor into the dock to provide a
snug fit for the player to be docked.
Selecting the correct dock adaptor
● 4 iPod dock adaptors are included. Each adaptor
fits the iPod models that are indicated on the
adaptor.
Playing iPod
1 Press PUSH TO OPEN
to open the dock.
2 Select the dock adaptor
of the correct type and
size, and snap it into the
dock (See “Dock
adaptor” ).
3 Correctly place your
iPod in the dock.
4 Press SOURCE
repeatedly or DOCK
on the set (iPOD on the remote control) to
select iPod source.
● The connected player will play automatically.
Notes:
– By using the buttons ( 2;, ¡1, 2™ and
VOLUME ) on the set and its remote control, the
following playback features are available: Play/
Pause, selecting next/previous track, fast
forwarding/rewinding and changing volume.
– The buttons ( 2;, ¡1, 2™ and VOLUME ) on
the set and its remote control can work only with
playback of the audio contents stored on the
docked player.
– Stop (Ç) function of disc playback is not
available to the docked player.
– To navigate the iPod menu, you may use MENU,
34and OK buttons on the remote control.
Charging iPod battery using the
dock
Docking your iPod to DC146, you can charge
the iPod in the standby mode and power-on
mode of DC146.
Notes:
– In standby mode, when no iPod is plugged in for
15 minutes, the set will auto switch to Eco power
mode.
– In Eco power standby mode, iPod cannot be
charged.
MIC
PUSH TO OPEN
DOCK FOR iPOD
RO SYSTEM DC14 6
SOURCE
DOCK
STANDBY
-
ON
REPEAT DBB
CD/CD
-
R/CD
-
RW COMPATIBLE
PRESET
iR
VOL
VOL
TUNING
Pg001-pg021_DC146_79_Eng 3/31/10, 10:1714
English
15
Clock/Timer
5 Press TIMER/SLEEP again.
➜ The clock digits for the minutes flash.
6 Press TUNING 4 ¢ (4 ¢ on the
remote control) to set the minutes.
7 Press TIMER/SLEEP to confirm the time.
➜ The timer is now set and activated.
Notes: .
– If CD source is selected and no disc is in the CD
tray or the disc has an error, TUNER will be
selected automatically.
– If iPod source is selected and no iPod player is
docked, TUNER will be selected automatically.
Activating and deactivating
TIMER
● In standby mode, press TIMER/SLEEP once.
➜ Display shows if activated, and disappears if
deactivated.
Activating and deactivating
SLEEP
The sleep timer enables the system to switch off
by itself after a set period of time.
● When the system is turned on, press TIMER/
SLEEP on the remote control
once or more.
➜ Display shows and one
of the sleep time options in
sequence: 60, 45, 30,15, 0,
60... if you have selected a
time.
● To deactivate, press TIMER/SLEEP on the
remote control once or more until “ 0“
is shown,
or press STANDBY ON 2on the system (or
POWER on the remote control).
➜ disappears from the display.
Setting the clock
1 In standby mode, press and hold CLOCK/
DISPLAY on the remote control set for 2
seconds.
2 Press PROG to select 12-hour or 24-hour
display.
3 Press CLOCK/DISPLAY to confirm.
➜ The clock digits for the hours flash.
4 Press TUNING 4 ¢ (4 ¢ on the
remote control) to set the hours.
5 Press CLOCK/DISPLAY again.
➜ The clock digits for the minutes flash.
6 Press TUNING 4 ¢ (4 ¢ on the
remote control) to set the minutes.
7 Press CLOCK/DISPLAY to confirm the time.
Setting the timer
● The system can be used as an alarm clock,
whereby the CD, iPod or TUNER is switched on
at a set time. The clock time needs to be set first
before the timer can be used.
1 In standby mode, press and hold TIMER/
SLEEP about 2 seconds on the remote control.
2 Press SOURCE (or DISC/iPOD/TUN on
the remote control) to select sound source.
3 Press TIMER/SLEEP to confirm your desired
mode.
➜ The clock digits for the hours flash.
4 Press TUNING 4 ¢ (4 ¢ on the
remote control) to set the hours.
MICRO SYSTE M DC146
SOURC E
DOCK
DBB
STANDBY
-
ON
VOL
VOL
TUNING
REPEAT
CD/CD
-
R/CD
-
RW COMPATIBLE
PRESE T
iR
iPOD
PROG
MENU
OK
Pg001-pg021_DC146_79_Eng 3/30/10, 17:5915
16
English
Specifications
AMPLIFIER
Output power ....................................... 2 x 1.5W RMS
Signal-to-noise ratio .......................... ≥ 60 dBA (IEC)
Frequency response ....................... 125 – 16000 Hz
Impedance loudspeakers ........................................... 8Ω
CD PLAYER
Frequency range ............................... 125 – 16000 Hz
Signal-to-noise ratio ............................................ 65 dBA
TUNER
FM wave range ................................... 87.5 – 108 MHz
MW wave range ................................ 531 – 1602 kHz
Sensitivity
– FM 26 dB sensitivity .......................................... 20 µV
– MW 26 dB sensitivity ................................... 5 mV/m
Total harmonic distortion ..................................... ≤ 5%
SPEAKERS
Bass reflex system
Dimensions (w x h x d) . 134 x 230 x 152 (mm)
GENERAL INFORMATION
AC Power ..................................... 220 – 230 V / 50 Hz
Dimensions (w x h x d) .. 148 x 233 x 216 (mm)
Weight (with/without speakers) ..................................
......................................................... approx. 3.65 / 1.53 kg
Power consumption
Active .......................................................................... 15 W
Standby .................................................................... < 4 W
Specifications and external appearance are
subject to change without notice.
Maintenance
Cleaning the Cabinet
● Use a soft cloth slightly moistened with a mild
detergent solution. Do not use a solution
containing alcohol, spirits, ammonia or abrasives.
Cleaning Discs
● When a disc becomes dirty,
clean it with a cleaning cloth.
Wipe the disc from the centre
out.
● Do not use solvents such as
benzene, thinner, commercially
available cleaners, or antistatic
spray intended for analogue records.
Cleaning the disc lens
● After prolonged use, dir t or dust may accumulate
at the disc lens. To ensure good playback quality,
clean the disc lens with Philips CD Lens Cleaner
or any commercially available cleaner. Follow the
instructions supplied with cleaner.
Pg001-pg021_DC146_79_Eng 3/30/10, 17:5916
English
17
“NO CD” is displayed.
Radio reception is poor.
The system does not react when buttons
are pressed.
Sound cannot be heard or is of poor
quality.
The left and right sound outputs are
reversed.
✔ Insert a disc.
✔ Check if the disc is inserted upside down.
✔ Wait until the moisture condensation at the lens
has cleared.
✔ Replace or clean the disc, see “Maintenance”.
✔ Use a finalized CD-RW or CD-R.
✔ If the signal is too weak, adjus the antenna for
better reception.
✔ Increase the distance between the System and
your TV or VCR.
✔ Remove and reconnect the AC power plug and
switch on the system again.
✔ Adjust the volume.
✔ Disconnect the headphones.
✔ Check that the speakers are connec ted
correctly.
✔ Check if the stripped speaker wire is clamped.
✔ Check the speaker connections and location.
WARNING
Under no circumstances should you try to repair the system yourself, as this will invalidate the
warranty. Do not open the system as there is a risk of electric shock.
If a fault occurs, first check the points listed below before taking the system for repair. If you
are unable to remedy a problem by following these hints, consult your dealer or Philips for
help.
Problem
Solution
Tr oubleshooting
Pg001-pg021_DC146_79_Eng 3/30/10, 17:5917
18
English
The remote control does not function
properly.
The time is not working.
The Clock/Timer setting is erased.
✔ Select the source (CD or TUNER, for example)
before pressing the function button (2;, 4,
¢).
✔ Reduce the distance between the remote
control and the system.
✔ Insert the batteries with their polarities
(+/– signs) aligned as indicated.
✔ Replace the batteries.
✔ Point the remote control directly towards the IR
sensor.
✔ Set the clock correctly.
✔ Switch on the timer.
✔ Power has been interrupted or the power cord
has been disconnected. Reset the clock/timer.
Troubleshooting
Problem
Solution
Pg001-pg021_DC146_79_Eng 3/30/10, 17:5918
19
DC146_79_UM_Eng 3/31/10, 15:2419
20
DC146_79_UM_Eng 3/31/10, 15:2420
Page is loading ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Philips DC146/79 User manual
-
Philips DC146 User manual
-
-
-
-
-
-
-
-