Digital Projection M-Vision Laser 18K User manual

Digital Projection
Brand
Digital Projection
Model
M-Vision Laser 18K
Category
Data projectors
Type
User manual
Rev C December 2017
M-Vision Laser 18K Series
High Brightness Digital Video Projector
4INSTALLATION AND QUICK-START GUIDE
4CONNECTION GUIDE
4OPERATING GUIDE
4REFERENCE GUIDE
118-056C
page i
Digital Projection M-Vision Laser 18K Series
Rev C December 2017
About This Document
Follow the instructions in this manual carefully to ensure safe and long-lasting use of the projector.
Symbols used in this manual
Many pages in this document have a dedicated area for notes. The information in that area is accompanied by the following symbols:
WARNING: this symbol indicates that there is a danger of physical injury to yourself and/or damage to the equipment
unless the instructions are closely followed.
ELECTRICAL WARNING: this symbol indicates that there is a danger of electrical shock unless the instructions are closely
followed.
LIGHT HAZARD WARNING: this symbol indicates that there is a danger of exposure to intensive light that may result in
personal injury unless the instructions are closely followed.
LASER WARNING: this symbol indicates that there is a potential hazard of eye exposure to laser radiation unless the
instructions are closely followed.
NOTE: this symbol indicates that there is some important information that you should read.
Product revision
Because we at Digital Projection continually strive to improve our products, we may change specications and designs, and add new features
without prior notice.
Updates may be available online - visit the Digital Projection website for all latest documents.
Legal notice
Trademarks and trade names mentioned in this document remain the property of their respective owners.
Digital Projection disclaims any proprietary interest in trademarks and trade names other than its own.
Copyright © 2017 Digital Projection Ltd. All rights reserved.
Notes
page ii
Digital Projection M-Vision Laser 18K Series
Rev C December 2017
Risk Group 3 Information
Light hazard warning
Failure to comply with the following may result in serious injury:
• No direct exposure to the beam is permitted, RG3 IEC 62471-5:2015.
• Operators control access to the beam within the hazard distance or install the projector at sufcient height to prevent
exposures of spectators’ eyes within the hazard distance.
The hazard distance (Fig. 1) is the distance measured from the projection lens at which the intensity or energy per unit of surface is lower
than the applicable exposure limit on the cornea or skin. If the person is within the hazard distance, the beam is considered unsafe for
exposure.
The hazard distance for this projector is 600 cm.
Notes
Fig. 1: hazard distance
page iii
Digital Projection M-Vision Laser 18K Series
Rev C December 2017
Light hazard labels on the body of the projector
Light hazard labelling is part of the product label.
1Product label
2Risk Group 3 label
3Hazard Warning symbol
4Not For Home Use logo
WIRED
REMOTE
RJ45
LAN
HDBaseT HDMI 1 DisplayPort 2DisplayPort 1 HDMI 2 3D SYNC - IN3G SDI
IN
3G SDI
OUT
3D SYNC - OUT
RS-2321 2TRIGGER
AC MAINS
交流電源輸入
AC POWER
SWITCH
交流電源開關
POWER
MENU EXIT
LENS
SHIFT
INPUT ASPECT PIC MUTE
AUTO
SYNC
CENTER
LENS
FOCUS ZOOM
CLASS 1 LASER PRODUCT
一类激光产品
IEC/EN 60825-1:2014
PRODUIT LASER DE CLASSE 1
第一類雷射產品
IEC/EN 60825-1:2014
GB 7247.1-2012 / IEC/EN 60825-1:2007
激光辐射
避免眼睛受到直接照射
3R类激光产品
波长 : 450-460 nm
最大脉冲能量: 0.48 mJ,
脉冲时间: 0.93 ms
激光輻射
避免眼睛受到直接照射
3R類激光產品
波長: 450-460 nm
最大脈衝能量: 0.48 mJ,
脈衝時間: 0.93 ms
警告 ！请勿直视镜头。
眼睛不要直接暴露于光辐射 。
RG3
危险距离：0-600厘米
警告 ！ 請勿直視鏡頭。
眼睛不要直接暴露於光輻射。
RG3
危險距離：0-600公分
RAYONNEMENT LASER
EXPOSITION DIRECTE DANGEREUSE
POUR LES YEUX
APPAREIL À LASER DE CLASSE 3R
longueur d'onde : 450-460nm
maximum énergie de impulsion : 0.48 mJ,
durée de impulsion : 0.93 ms
LASER RADIATION
AVOID DIRECT EYE EXPOSURE
CLASS 3R LASER PRODUCT
Emitted wavelength : 450-460 nm
Max. Pulse energy: 0.48 mJ,
Pulse duration: 0.93 ms
Warning ! Do not look into the beam.
No direct eye exposure to the beam
is permitted.
RG3
Hazard Distance : 0-600cm
Avertissement ! Ne Pas Regarder
Directement Dans Le Faisceau.
L’exposition Directe Des Yeux Au
Faisceau Est Interdite.
RG3
Distance À Risque : 0-600cm
3262163400
QR
Code
Part No.: 118-053A
*XXXXXXXXXXXXX*
MANUFACTURED YYYY.MM.DD
Code 39 or 128 of serial no
DLP PROJECTOR / DLP Projecteur
(
數位投影機/数字投影机
)
制造商 : Digital Projection Limited
Greenside Way Middleton Manchester, M24 1XX UK
製造地:中國 / 制造地:中国 / Made in China
326XXXXXXX WJ XXXX
Model/Modèle
(型號 / 型号) :
AC Input / Entrée CA
(輸入 / 输入)
:
200-240V 50/60Hz 9.3A
AC Input / Entrée CA
(輸入 / 输入)
:
110-130V 50/60Hz 11.7A
Complies with FDA performance standards for laser
products except for deviations pursuant to Laser
Notice No. 50, dated June 24, 2007
M-Vision Laser yyyyyy
This device complies with part 15 of the FCC rules.
Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received,
including interference that may cause undesired operation.
CAN ICES-3(A) /NMB-3(A)
警告使用者: 此为A级产品，在生活环境中，该产品可能会造成无线
电干扰。在这种情况下，可能需要用户对干扰采取切实可行的措施。
警告使用者：此為甲類資訊技術設備，於居住環境中使用，可能會
造成射頻擾動，在此中情況下，使用者會被要求採取某些適當的對策。
+822-515-5303
KTLZUXXXXX-XXXXX
MSIP-REM-DVP-XXXXXXXXX
:
:
:
/ :
:
델타 비디오 디스플레이
시스템 (우장) 리미티드
R41086
RoHS
12
WIRED
REMOTE
RJ45
LAN
HDBaseT HDMI 1 DisplayPort 2DisplayPort 1 HDMI 2 3D SYNC - IN3G SDI
IN
3G SDI
OUT
3D SYNC - OUT
RS-2321 2TRIGGER
AC MAINS
交流電源輸入
AC POWER
SWITCH
交流電源開關
POWER
MENU EXIT
LENS
SHIFT
INPUT ASPECT PIC MUTE
AUTO
SYNC
CENTER
LENS
FOCUS ZOOM
CLASS 1 LASER PRODUCT
一类激光产品
IEC/EN 60825-1:2014
PRODUIT LASER DE CLASSE 1
第一類雷射產品
IEC/EN 60825-1:2014
GB 7247.1-2012 / IEC/EN 60825-1:2007
激光辐射
避免眼睛受到直接照射
3R类激光产品
波长 : 450-460 nm
最大脉冲能量: 0.48 mJ,
脉冲时间: 0.93 ms
激光輻射
避免眼睛受到直接照射
3R類激光產品
波長: 450-460 nm
最大脈衝能量: 0.48 mJ,
脈衝時間: 0.93 ms
警告 ！请勿直视镜头。
眼睛不要直接暴露于光辐射 。
RG3
危险距离：0-600厘米
警告 ！ 請勿直視鏡頭。
眼睛不要直接暴露於光輻射。
RG3
危險距離：0-600公分
RAYONNEMENT LASER
EXPOSITION DIRECTE DANGEREUSE
POUR LES YEUX
APPAREIL À LASER DE CLASSE 3R
longueur d'onde : 450-460nm
maximum énergie de impulsion : 0.48 mJ,
durée de impulsion : 0.93 ms
LASER RADIATION
AVOID DIRECT EYE EXPOSURE
CLASS 3R LASER PRODUCT
Emitted wavelength : 450-460 nm
Max. Pulse energy: 0.48 mJ,
Pulse duration: 0.93 ms
Warning ! Do not look into the beam.
No direct eye exposure to the beam
is permitted.
RG3
Hazard Distance : 0-600cm
Avertissement ! Ne Pas Regarder
Directement Dans Le Faisceau.
L’exposition Directe Des Yeux Au
Faisceau Est Interdite.
RG3
Distance À Risque : 0-600cm
3262163400
QR
Code
Part No.: 118-053A
*XXXXXXXXXXXXX*
MANUFACTURED YYYY.MM.DD
Code 39 or 128 of serial no
DLP PROJECTOR / DLP Projecteur
(
數位投影機/数字投影机
)
制造商 : Digital Projection Limited
Greenside Way Middleton Manchester, M24 1XX UK
製造地:中國 / 制造地:中国 / Made in China
326XXXXXXX WJ XXXX
Model/Modèle
(型號 / 型号) :
AC Input / Entrée CA
(輸入 / 输入)
:
200-240V 50/60Hz 9.3A
AC Input / Entrée CA
(輸入 / 输入)
:
110-130V 50/60Hz 11.7A
Complies with FDA performance standards for laser
products except for deviations pursuant to Laser
Notice No. 50, dated June 24, 2007
M-Vision Laser yyyyyy
This device complies with part 15 of the FCC rules.
Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received,
including interference that may cause undesired operation.
CAN ICES-3(A) /NMB-3(A)
警告使用者: 此为A级产品，在生活环境中，该产品可能会造成无线
电干扰。在这种情况下，可能需要用户对干扰采取切实可行的措施。
警告使用者：此為甲類資訊技術設備，於居住環境中使用，可能會
造成射頻擾動，在此中情況下，使用者會被要求採取某些適當的對策。
+822-515-5303
KTLZUXXXXX-XXXXX
MSIP-REM-DVP-XXXXXXXXX
:
:
:
/ :
:
델타 비디오 디스플레이
시스템 (우장) 리미티드
R41086
RoHS
43
Notes
page iv
Digital Projection M-Vision Laser 18K Series
Rev C December 2017
Laser Information
Caution - use of controls or adjustments or performance of procedures other than those specied herein may result in
hazardous radiation exposure.
Notes
LASER LIGHT
AVOID DIRECT EYE EXPOSURE
CLASS 3R LASER PRODUCT
455-470nm <13Watts
CLASSIFIED EN/IEC 60825-1 2007
page v
Digital Projection M-Vision Laser 18K Series
Rev C December 2017
Introduction
Congratulations on your purchase of this Digital Projection product.
Your projector has the following key features:
• WUXGA native resolution projector delivering 18,000 ISO lumens.
• Support for Frame Sequential and Dual Pipe 3D formats as well as Frame Packed, Side-by-Side etc. formats.
• HDBaseT® for transmission of uncompressed High Denition Video up to 100 m from the source.
• 3G-SDI with loop-through.
• Blanking control for custom input window sizing.
• Edge Blending with black level correction.
• Cornerstone, Vertical & Horizontal Keystone, Pincushion & Barrel, and Image Rotation.
• Non-Linear warp for irregular projection surfaces.
• Separate control of screen and source aspect ratio.
• Contstant brightness mode maintains light output at selected levels.
• Control via LAN and RS232.
• Motorised lens mount.
A serial number is located on the side of the projector. Record it here:
Notes
page vi
Digital Projection M-Vision Laser 18K Series
Rev C December 2017
CONTENTS
INSTALLATION AND QUICK-START GUIDE ..............................1
WHAT’S IN THE BOX? ................................................................... 3
CONNECTING THE POWER SUPPLY ............................................. 4
PROJECTOR OVERVIEW ............................................................... 5
Front and rear views ............................................................................. 5
Control panel ......................................................................................... 6
Projector indicators ................................................................................ 7
REMOTE CONTROL ....................................................................... 8
Infrared reception ................................................................................ 11
POSITIONING THE SCREEN AND PROJECTOR ........................... 12
Roll and pitch ...................................................................................... 13
Stacking instructions ........................................................................... 14
CHANGING THE LENS ................................................................. 17
Inserting a new lens ............................................................................ 17
Removing the lens .............................................................................. 18
OPERATING THE PROJECTOR .................................................... 19
Switching the projector on ................................................................... 19
Switching the projector off ................................................................... 19
Selecting an input signal ..................................................................... 20
Selecting a test pattern ....................................................................... 20
Adjusting the lens ................................................................................ 21
Adjusting the image............................................................................. 21
CONNECTION GUIDE ............................................................................23
SIGNAL INPUTS AND OUTPUTS .................................................. 25
Digital inputs and outputs .................................................................... 25
EDID on the DisplayPort, HDMI and HDBaseT inputs ........................ 26
Using DisplayPort/HDMI/HDBaseT switchers with the projector ........ 26
3D connections ................................................................................... 27
Frame sequential 1080p and WUXGA 3D sources at 100 and 120 Hz ............... 27
Dual Pipe 1080p, WUXGA and WQXGA 3D sources at 100 and 120 Hz ............ 27
3D Sync............................................................................................... 28
3D Sync In ......................................................................................... 28
3D Sync Out ....................................................................................... 28
CONTROL CONNECTIONS ........................................................... 29
LAN connection examples .................................................................. 30
RS232 connection example ............................................................... 31
page vii
Digital Projection M-Vision Laser 18K Series
Rev C December 2017
OPERATING GUIDE ................................................................................33
USING THE MENUS ..................................................................... 35
Opening the OSD ................................................................................ 35
Opening a menu.................................................................................. 35
Exiting menus and closing the OSD.................................................... 35
Inside a menu...................................................................................... 36
Accessing sub-menus ........................................................................... 36
Executing commands............................................................................ 36
Editing projector settings ..................................................................... 37
Using a slider to set a value .................................................................... 37
Editing numeric values .......................................................................... 37
USING THE PROJECTOR ............................................................. 38
Main menu .......................................................................................... 38
Lens menu .......................................................................................... 39
Lens Control ....................................................................................... 39
Lens Memory ...................................................................................... 40
Image menu ........................................................................................ 41
Color menu.......................................................................................... 42
Color Space ....................................................................................... 42
Color Mode ........................................................................................ 43
Geometry menu .................................................................................. 48
Aspect Ratio ....................................................................................... 48
Digital Zoom ....................................................................................... 50
Overscan ........................................................................................... 51
Blanking ............................................................................................ 52
Keystone ........................................................................................... 53
4 Corners .......................................................................................... 55
Rotation ............................................................................................ 56
Pincushion / Barrel ............................................................................... 57
Arc ................................................................................................... 58
Custom Warp ..................................................................................... 58
Edge Blend menu................................................................................ 59
Blend Width........................................................................................ 60
Black Level Uplift ................................................................................. 61
3D menu.............................................................................................. 62
3D types ............................................................................................ 63
Some 3D settings explained ................................................................... 64
Laser menu ......................................................................................... 65
Setup menu ......................................................................................... 66
ColorMax Setting ................................................................................. 68
Power On/Off ...................................................................................... 69
Clock Adjust ....................................................................................... 70
OSD Settings ...................................................................................... 71
Memory ............................................................................................. 71
Network menu ..................................................................................... 72
PIP menu ............................................................................................ 73
Information menu ................................................................................ 74
Signal Format ..................................................................................... 74
System Status .................................................................................... 75
Thermal Status.................................................................................... 75
Factory Reset ..................................................................................... 76
CONTENTS (continued)
page viii
Digital Projection M-Vision Laser 18K Series
Rev C December 2017
REFERENCE GUIDE ................................................................................77
THE DMD™ .................................................................................. 79
CHOOSING A LENS ..................................................................... 81
Basic calculation ................................................................................. 82
Basic calculation example ................................................................... 83
Full lens calculation ............................................................................. 84
Introducing TRC .................................................................................. 84
Calculating TRC .................................................................................. 85
Calculating the throw ratio with TRC ......................................................... 86
Full lens calculation example .............................................................. 87
POSITIONING THE SCREEN AND PROJECTOR ........................... 88
POSITIONING THE IMAGE ........................................................... 89
FRAME RATES AND PULLDOWNS EXPLAINED ........................... 91
Interlaced and progressive scan ......................................................... 91
Frame rates of image sources ............................................................ 91
Pulldowns - conversion into destination formats ................................. 92
2:3 (normal) pulldown ........................................................................... 92
2:3:3:2 (advanced) pulldown ................................................................... 93
APPENDIX A: LENS PART NUMBERS .......................................... 94
APPENDIX B: SUPPORTED SIGNAL INPUT MODES .................... 95
2D formats........................................................................................... 95
3D formats........................................................................................... 98
APPENDIX C: WIRING DETAILS ................................................ 100
RS232 ............................................................................................... 100
Trigger 1 & Trigger 2 ......................................................................... 101
Wired remote control ......................................................................... 101
Sync IN and Sync OUT ..................................................................... 101
APPENDIX D: GLOSSARY OF TERMS ....................................... 102
CONTENTS (continued)
Digital Projection M-Vision Laser 18K Series
This page is intentionally left blank.
Rev C December 2017
M-Vision Laser 18K Series
High Brightness Digital Video Projector
INSTALLATION AND QUICK-START GUIDE
4
Digital Projection M-Vision Laser 18K Series
Installation and Quick-Start Guide
IN THIS GUIDE
Rev C December 2017
IN THIS GUIDE
WHAT’S IN THE BOX? .....................................................................................3
CONNECTING THE POWER SUPPLY ...........................................................4
PROJECTOR OVERVIEW .................................................................................5
Front and rear views ...................................................................................................5
Control panel ...............................................................................................................6
Projector indicators ........................................................................................................... 7
REMOTE CONTROL ..........................................................................................8
Infrared reception ......................................................................................................11
POSITIONING THE SCREEN AND PROJECTOR .....................................12
Roll and pitch ............................................................................................................13
Stacking instructions ................................................................................................14
CHANGING THE LENS ..................................................................................17
Inserting a new lens ..................................................................................................17
Removing the lens ....................................................................................................18
OPERATING THE PROJECTOR ...................................................................19
Switching the projector on .......................................................................................19
Switching the projector off .......................................................................................19
Selecting an input signal ..........................................................................................20
Selecting a test pattern .............................................................................................20
Adjusting the lens .....................................................................................................21
Adjusting the image ..................................................................................................21
page 3
Digital Projection M-Vision Laser 18K Series
Installation and Quick-Start Guide
WHAT’S IN THE BOX?
Rev C December 2017
What’s In The Box? Notes
Make sure your box contains
everything listed. If any pieces are
missing, contact your dealer.
You should save the original box
and packing materials, in case you
ever need to ship your projector.
The projector is shipped without a
lens.
Only one power cable - dependent
on the destination territory - will be
supplied with the projector.
A stacking kit is also provided in
some regions.
Remote control
Pic Mute
OFF ON
MENU
EXIT INFO
HDMI1
OK
OFF ON
ALT
LENS
FOCUS ZOOM
IN
OUT
IN
OUT
SHIFT
21 3
HDMI2 DVI
DISPLAYPORT
HD-T 3GSDI
VGA COMP1 COMP2
BRI
TEST
CON GAMMA
R G B ALL
3D EYE PIP SWAP
456
7 8 9 0
ALT
ADDR
OSD
OFF ON
DEFAULT
FREEZE RE-SYNC
A B C D
USER PRESET
2x AAA batteries
User Manual on disc Important Information
Power cable, Europe Power cable, North America
Projector
Power cable, United Kingdom Power cable, China
HDMI cable
page 4
Digital Projection M-Vision Laser 18K Series
Installation and Quick-Start Guide
CONNECTING THE POWER SUPPLY
Rev C December 2017
Connecting The Power Supply
Firmly push the mains connector into the socket 1, then press the ON/OFF switch 2.
Notes
Use only the power cable
provided.
Ensure that the power outlet
includes a ground connection as
this equipment MUST be earthed.
Handle the power cable carefully
and avoid sharp bends. Do not
use a damaged power cable.
When operating on 110V Light
output power is reduced by approx
35%.
1 2
page 5
Digital Projection M-Vision Laser 18K Series
Installation and Quick-Start Guide
PROJECTOR OVERVIEW
Rev C December 2017
Projector Overview
Front and rear views
1 Indicators: TEMP, LIGHT, STATUS and POWER
2 Lens mount
3 Air inlet
4 Lifting handle
5 Air inlet
6 Front infrared window
7 Stacking feet
8 Air outlet
9 Rear infrared window
10 Connections panel
11 Lifting handle
12 Control panel
13 Adjustable feet
14 Stacking feet
15 Mains socket and switch
Notes
Front view
5
3
2
1
7
6
4
Rear view
12108
14 1513
119
page 6
Digital Projection M-Vision Laser 18K Series
Installation and Quick-Start Guide
PROJECTOR OVERVIEW
Rev C December 2017
Control panel
1 POWER
Switches the projector on and off
(STANDBY).
2 INPUT
Switches to the next input source.
3 AUTO SYNC
Re-synchronises with the current input
signal.
4 ASPECT
Changes the aspect ratio.
5 CENTER LENS
Centers the lens.
6 PIC MUTE
Shows and hides the projected image.
When OFF, the light source is completely
switched off and the screen is black.
7 MENU
Displays and exits the OSD.
8 Arrow buttons & ENTER
Navigation buttons used to highlight menu
entries in the OSD.
Press ENTER to open or execute the
highlighted menu entry.
9 EXIT
Exits the current OSD page and enters the
level above.
10 LENS SHIFT arrow buttons
Each of these buttons moves the lens in the
specied direction.
11 FOCUS plus and minus buttons
Used to move the focus in and out.
12 ZOOM plus and minus buttons
Used to zoom in and out.
POWER
INPUT AUTO
SYNC ASPECT CENTER
LENS PIC MUTE
1 2 3 4 5 6
7 8 9 10 11 12
Notes
AUTO SYNC and ASPECT do not
work when the projector uses HDMI
3 or 4.
page 7
Digital Projection M-Vision Laser 18K Series
Installation and Quick-Start Guide
PROJECTOR OVERVIEW
Rev C December 2017
Projector indicators
TEMP. Off = no problem
Flashing red = temperature error
LIGHT Off = light is switched off
Flashing green = light is preparing to switch on
Flashing red (cycles of six ashes) = light module failure
On, green = light is switched on
STATUS Off = no problem
Flashing red (continuously) = cover error
Flashing red (cycles of four ashes) = fan error
On, red = system error
POWER Off = the projector is switched off
Flashing green = the projector is warming up
Flashing amber = the projector is cooling down
On, red = STANDBY mode
On, green = the projector is switched on
Notes
POWERSTAT USLIGHTTEMP.
page 8
Digital Projection M-Vision Laser 18K Series
Installation and Quick-Start Guide
REMOTE CONTROL
Rev C December 2017
Remote Control
1 Power ON / OFF
Turns power on and off.
2 Pic Mute OPEN / CLOSED
Shows and hides the projected image.
When CLOSED, the light source is completely switched off and the screen is black.
2 OSD ON / OFF
Enable and disable screen timeout messages and control whether to show the OSD
during projection.
4 MENU
Access the OSD. If the OSD is open, press this button to go back to the previous menu.
5 Navigation (arrows and OK)
Navigate through the menus with the arrows, conrm your choice with OK.
In lens adjustment modes, the arrows are used to move, zoom or focus the lens. See 11
below.
In lens adjustment modes, or when the OSD is not showing, the OK button switches
between modes: Shift Adjustment and Zoom / Focus Adjustment.
6 EXIT
Go up one level in the OSD. When the top level is reached, press to close the OSD.
7 FREEZE
Freeze the current frame.
8 DEFAULT
When editing a parameter, press this button to restore the default value.
9 INFO
Access information about the projector.
10 RE-SYNC
Re-synchronise with the current input signal.
continues on next page...
Pic Mute
OPEN CLOSE
MENU
EXIT INFO
HDMI1
OK
OFF ON
ALT
LENS
FOCUS ZOOM
IN
OUT
IN
OUT
SHIFT
21 3
HDMI2 DVI
DisplayPort1
HD-T 3GSDI
VGA COMP1 COMP2
HDMI3
TEST
HDMI4
DisplayPort2
R G B ALL
3D EYE PIP SWAP
456
7 8 9 0
ALT
ADDR
OSD
OFF ON
DEFAULT
FREEZE RE-SYNC
A B C D
USER PRESET
1
2
5
6
8
4
9
7
3
10
Notes
FREEZE and RE-SYNC are not
available when the projector uses
input HDMI 3 or 4.
This projector does not use the
following options on the remote:
DVI, VGA, COMP 1 and COMP 2.
Remote control
page 9
Digital Projection M-Vision Laser 18K Series
Installation and Quick-Start Guide
REMOTE CONTROL
Rev C December 2017
11 LENS adjustment
FOCUS IN / OUT: adjust focus.
SHIFT: press and hold this button, then use the Navigation arrow
buttons to move the lens.
ZOOM IN / OUT: adjust zoom.
12 USER PRESET A, B, C, D
Load user presets.
13 ALT
Press and hold this button to access alternative functions for all
buttons with a green label.
14 DVI / DisplayPort2 / numeric input 3
There is no DVI input on this projector.
Use with ALT to select the DisplayPort 2 input.
15 HDMI 2 / HDMI 4 / numeric input 2
Select the HDMI 1 input.
Use with ALT to select the HDMI 4 input.
16 HDMI 1 / HDMI 3 / numeric input 1
Select the HDMI 1 input.
Use with ALT to select the HDMI 3 input.
17 TEST / SWAP / numeric input 0
Show a test pattern. Press again to show the next test pattern:
...Off, White, Black, Red, Green, Blue, CheckerBoard,
CrossHatch, V Burst, H Burst, ColorBar...
When PIP mode is on, use this button with ALT to swap the main and
sub images.
continues on next page...
Notes
This projector does not use the
following options on the remote:
HDMI 3 and HDMI 4
DVI, VGA, COMP 1 and COMP 2.
Remote control
Pic Mute
OPEN CLOSE
MENU
EXIT INFO
HDMI1
OK
OFF ON
ALT
LENS
FOCUS ZOOM
IN
OUT
IN
OUT
SHIFT
21 3
HDMI2 DVI
DisplayPort1
HD-T 3GSDI
VGA COMP1 COMP2
HDMI3
TEST
HDMI4
DisplayPort2
R G B ALL
3D EYE PIP SWAP
456
7 8 9 0
ALT
ADDR
OSD
OFF ON
DEFAULT
FREEZE RE-SYNC
A B C D
USER PRESET
13
11
12
14
15
16
17
page 10
Digital Projection M-Vision Laser 18K Series
Installation and Quick-Start Guide
REMOTE CONTROL
Rev C December 2017
17 DISPLAYPORT 1 / R / numeric input 4
Select DisplayPort 1 input.
18 HD-T / G / numeric input 5
Select the HDBaseT input.
19 3GSDI / B / numeric input 6
Select the 3G-SDI input.
20 VGA / 3D / numeric input 7
There is no VGA input on this projector.
Use with ALT to toggle the 3D Format setting between Off and Auto.
21 COMP1 / EYE / numeric input 8
There is no Component 1 input on this projector.
Use with ALT to switch between left and right eye 3D dominance.
22 COMP2 / PIP / numeric input 9
There is no Component 2 input on this projector.
Use with ALT to switch on Picture In Picture (PIP) mode.
23 ADDR / ALL (with red indicator at the top)
Assign and unassign an IR remote address.
To assign an address:
1. Press and hold this button until the indicator starts ashing.
2. Release this button and while the indicator is still ashing, enter
a two-digit address using the numeric input buttons. The indicator
will ash three times quickly to conrm the change.
To unassign an address and return to the default address 00,
• Press and hold ALT and this button simultaneously until the
indicator ashes to conrm the change.
Notes
This projector does not use the
following options on the remote:
HDMI 3 and HDMI 4
DVI, VGA, COMP 1 and COMP 2.
Remote control bottom
Pic Mute
OPEN CLOSE
MENU
EXIT INFO
HDMI1
OK
OFF ON
ALT
LENS
FOCUS ZOOM
IN
OUT
IN
OUT
SHIFT
21 3
HDMI2 DVI
DisplayPort1
HD-T 3GSDI
VGA COMP1 COMP2
HDMI3
TEST
HDMI4
DisplayPort2
R G B ALL
3D EYE PIP SWAP
456
7 8 9 0
ALT
ADDR
OSD
OFF ON
DEFAULT
FREEZE RE-SYNC
A B C D
USER PRESET
23
18
19
17
20
21
22
Pic Mute
OPEN CLOSE
MENU
EXIT INFO
HDMI1
OK
OFF ON
ALT
LENS
FOCUS ZOOM
IN
OUT
IN
OUT
SHIFT
21 3
HDMI2 DVI
DisplayPort1
HD-T 3GSDI
VGA COMP1 COMP2
HDMI3
TEST
HDMI4
DisplayPort2
R G B ALL
3D EYE PIP SWAP
456
7 8 9 0
ALT
ADDR
OSD
OFF ON
DEFAULT
FREEZE RE-SYNC
A B C D
USER PRESET
Remote control top
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84
  • Page 85 85
  • Page 86 86
  • Page 87 87
  • Page 88 88
  • Page 89 89
  • Page 90 90
  • Page 91 91
  • Page 92 92
  • Page 93 93
  • Page 94 94
  • Page 95 95
  • Page 96 96
  • Page 97 97
  • Page 98 98
  • Page 99 99
  • Page 100 100
  • Page 101 101
  • Page 102 102
  • Page 103 103
  • Page 104 104
  • Page 105 105
  • Page 106 106
  • Page 107 107
  • Page 108 108
  • Page 109 109
  • Page 110 110
  • Page 111 111
  • Page 112 112
  • Page 113 113
  • Page 114 114
  • Page 115 115
  • Page 116 116
  • Page 117 117
  • Page 118 118
  • Page 119 119

Digital Projection M-Vision Laser 18K User manual

Digital Projection
Brand
Digital Projection
Model
M-Vision Laser 18K
Category
Data projectors
Type
User manual
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents