Digital Projection M-Vision Laser 18K User manual

Rev C December 2017

M-Vision Laser 18K Series

High Brightness Digital Video Projector

4INSTALLATION AND QUICK-START GUIDE

4CONNECTION GUIDE

4OPERATING GUIDE

4REFERENCE GUIDE

118-056C

page i

Digital Projection M-Vision Laser 18K Series

Rev C December 2017

About This Document

Follow the instructions in this manual carefully to ensure safe and long-lasting use of the projector.

Symbols used in this manual

Many pages in this document have a dedicated area for notes. The information in that area is accompanied by the following symbols:

WARNING: this symbol indicates that there is a danger of physical injury to yourself and/or damage to the equipment

unless the instructions are closely followed.

ELECTRICAL WARNING: this symbol indicates that there is a danger of electrical shock unless the instructions are closely

followed.

LIGHT HAZARD WARNING: this symbol indicates that there is a danger of exposure to intensive light that may result in

personal injury unless the instructions are closely followed.

LASER WARNING: this symbol indicates that there is a potential hazard of eye exposure to laser radiation unless the

instructions are closely followed.

NOTE: this symbol indicates that there is some important information that you should read.

Product revision

Because we at Digital Projection continually strive to improve our products, we may change specications and designs, and add new features

without prior notice.

Updates may be available online - visit the Digital Projection website for all latest documents.

Legal notice

Trademarks and trade names mentioned in this document remain the property of their respective owners.

Digital Projection disclaims any proprietary interest in trademarks and trade names other than its own.

Notes

page ii

Digital Projection M-Vision Laser 18K Series

Rev C December 2017

Risk Group 3 Information

Light hazard warning

Failure to comply with the following may result in serious injury:

• No direct exposure to the beam is permitted, RG3 IEC 62471-5:2015.

• Operators control access to the beam within the hazard distance or install the projector at sufcient height to prevent

exposures of spectators’ eyes within the hazard distance.

The hazard distance (Fig. 1) is the distance measured from the projection lens at which the intensity or energy per unit of surface is lower

than the applicable exposure limit on the cornea or skin. If the person is within the hazard distance, the beam is considered unsafe for

exposure.

The hazard distance for this projector is 600 cm.

Notes

Fig. 1: hazard distance

page iii

Digital Projection M-Vision Laser 18K Series

Rev C December 2017

Light hazard labels on the body of the projector

Light hazard labelling is part of the product label.

1Product label

2Risk Group 3 label

3Hazard Warning symbol

4Not For Home Use logo

WIRED

REMOTE

RJ45

LAN

HDBaseT HDMI 1 DisplayPort 2DisplayPort 1 HDMI 2 3D SYNC - IN3G SDI

IN

3G SDI

OUT

3D SYNC - OUT

RS-2321 2TRIGGER

AC MAINS

交流電源輸入

AC POWER

SWITCH

交流電源開關

POWER

MENU EXIT

LENS

SHIFT

INPUT ASPECT PIC MUTE

AUTO

SYNC

CENTER

LENS

FOCUS ZOOM

CLASS 1 LASER PRODUCT

一类激光产品

IEC/EN 60825-1:2014

PRODUIT LASER DE CLASSE 1

第一類雷射產品

IEC/EN 60825-1:2014

GB 7247.1-2012 / IEC/EN 60825-1:2007

激光辐射

避免眼睛受到直接照射

3R类激光产品

波长 : 450-460 nm

最大脉冲能量: 0.48 mJ,

脉冲时间: 0.93 ms

激光輻射

避免眼睛受到直接照射

3R類激光產品

波長: 450-460 nm

最大脈衝能量: 0.48 mJ,

脈衝時間: 0.93 ms

警告！请勿直视镜头。

眼睛不要直接暴露于光辐射。

RG3

危险距离：0-600厘米

警告！請勿直視鏡頭。

眼睛不要直接暴露於光輻射。

RG3

危險距離：0-600公分

RAYONNEMENT LASER

EXPOSITION DIRECTE DANGEREUSE

POUR LES YEUX

APPAREIL À LASER DE CLASSE 3R

longueur d'onde : 450-460nm

maximum énergie de impulsion : 0.48 mJ,

durée de impulsion : 0.93 ms

LASER RADIATION

AVOID DIRECT EYE EXPOSURE

CLASS 3R LASER PRODUCT

Emitted wavelength : 450-460 nm

Max. Pulse energy: 0.48 mJ,

Pulse duration: 0.93 ms

Warning ! Do not look into the beam.

No direct eye exposure to the beam

is permitted.

RG3

Hazard Distance : 0-600cm

Avertissement ! Ne Pas Regarder

Directement Dans Le Faisceau.

L’exposition Directe Des Yeux Au

Faisceau Est Interdite.

RG3

Distance À Risque : 0-600cm

3262163400

QR

Code

Part No.: 118-053A

*XXXXXXXXXXXXX*

MANUFACTURED YYYY.MM.DD

Code 39 or 128 of serial no

DLP PROJECTOR / DLP Projecteur

(

數位投影機/数字投影机

)

制造商 : Digital Projection Limited

Greenside Way Middleton Manchester, M24 1XX UK

製造地:中國 / 制造地:中国 / Made in China

326XXXXXXX WJ XXXX

Model/Modèle

(型號 / 型号) :

AC Input / Entrée CA

(輸入 / 输入)

:

200-240V 50/60Hz 9.3A

AC Input / Entrée CA

(輸入 / 输入)

:

110-130V 50/60Hz 11.7A

Complies with FDA performance standards for laser

products except for deviations pursuant to Laser

Notice No. 50, dated June 24, 2007

M-Vision Laser yyyyyy

This device complies with part 15 of the FCC rules.

Operation is subject to the following two conditions:

(1) this device may not cause harmful interference, and

(2) this device must accept any interference received,

including interference that may cause undesired operation.

CAN ICES-3(A) /NMB-3(A)

警告使用者: 此为A级产品，在生活环境中，该产品可能会造成无线

电干扰。在这种情况下，可能需要用户对干扰采取切实可行的措施。

警告使用者：此為甲類資訊技術設備，於居住環境中使用，可能會

造成射頻擾動，在此中情況下，使用者會被要求採取某些適當的對策。

+822-515-5303

KTLZUXXXXX-XXXXX

MSIP-REM-DVP-XXXXXXXXX

:

/ :

:

델타 비디오 디스플레이

시스템 (우장) 리미티드

R41086

RoHS

12

WIRED

REMOTE

RJ45

LAN

HDBaseT HDMI 1 DisplayPort 2DisplayPort 1 HDMI 2 3D SYNC - IN3G SDI

IN

3G SDI

OUT

3D SYNC - OUT

RS-2321 2TRIGGER

AC MAINS

交流電源輸入

AC POWER

SWITCH

交流電源開關

POWER

MENU EXIT

LENS

SHIFT

INPUT ASPECT PIC MUTE

AUTO

SYNC

CENTER

LENS

FOCUS ZOOM

CLASS 1 LASER PRODUCT

一类激光产品

IEC/EN 60825-1:2014

PRODUIT LASER DE CLASSE 1

第一類雷射產品

IEC/EN 60825-1:2014

GB 7247.1-2012 / IEC/EN 60825-1:2007

激光辐射

避免眼睛受到直接照射

3R类激光产品

波长 : 450-460 nm

最大脉冲能量: 0.48 mJ,

脉冲时间: 0.93 ms

激光輻射

避免眼睛受到直接照射

3R類激光產品

波長: 450-460 nm

最大脈衝能量: 0.48 mJ,

脈衝時間: 0.93 ms

警告！请勿直视镜头。

眼睛不要直接暴露于光辐射。

RG3

危险距离：0-600厘米

警告！請勿直視鏡頭。

眼睛不要直接暴露於光輻射。

RG3

危險距離：0-600公分

RAYONNEMENT LASER

EXPOSITION DIRECTE DANGEREUSE

POUR LES YEUX

APPAREIL À LASER DE CLASSE 3R

longueur d'onde : 450-460nm

maximum énergie de impulsion : 0.48 mJ,

durée de impulsion : 0.93 ms

LASER RADIATION

AVOID DIRECT EYE EXPOSURE

CLASS 3R LASER PRODUCT

Emitted wavelength : 450-460 nm

Max. Pulse energy: 0.48 mJ,

Pulse duration: 0.93 ms

Warning ! Do not look into the beam.

No direct eye exposure to the beam

is permitted.

RG3

Hazard Distance : 0-600cm

Avertissement ! Ne Pas Regarder

Directement Dans Le Faisceau.

L’exposition Directe Des Yeux Au

Faisceau Est Interdite.

RG3

Distance À Risque : 0-600cm

3262163400

QR

Code

Part No.: 118-053A

*XXXXXXXXXXXXX*

MANUFACTURED YYYY.MM.DD

Code 39 or 128 of serial no

DLP PROJECTOR / DLP Projecteur

(

數位投影機/数字投影机

)

制造商 : Digital Projection Limited

Greenside Way Middleton Manchester, M24 1XX UK

製造地:中國 / 制造地:中国 / Made in China

326XXXXXXX WJ XXXX

Model/Modèle

(型號 / 型号) :

AC Input / Entrée CA

(輸入 / 输入)

:

200-240V 50/60Hz 9.3A

AC Input / Entrée CA

(輸入 / 输入)

:

110-130V 50/60Hz 11.7A

Complies with FDA performance standards for laser

products except for deviations pursuant to Laser

Notice No. 50, dated June 24, 2007

M-Vision Laser yyyyyy

This device complies with part 15 of the FCC rules.

Operation is subject to the following two conditions:

(1) this device may not cause harmful interference, and

(2) this device must accept any interference received,

including interference that may cause undesired operation.

CAN ICES-3(A) /NMB-3(A)

警告使用者: 此为A级产品，在生活环境中，该产品可能会造成无线

电干扰。在这种情况下，可能需要用户对干扰采取切实可行的措施。

警告使用者：此為甲類資訊技術設備，於居住環境中使用，可能會

造成射頻擾動，在此中情況下，使用者會被要求採取某些適當的對策。

+822-515-5303

KTLZUXXXXX-XXXXX

MSIP-REM-DVP-XXXXXXXXX

:

/ :

:

델타 비디오 디스플레이

시스템 (우장) 리미티드

R41086

RoHS

43

Notes

page iv

Digital Projection M-Vision Laser 18K Series

Rev C December 2017

Laser Information

Caution - use of controls or adjustments or performance of procedures other than those specied herein may result in

hazardous radiation exposure.

Notes

LASER LIGHT

AVOID DIRECT EYE EXPOSURE

CLASS 3R LASER PRODUCT

455-470nm <13Watts

CLASSIFIED EN/IEC 60825-1 2007

page v

Digital Projection M-Vision Laser 18K Series

Rev C December 2017

Introduction

Congratulations on your purchase of this Digital Projection product.

Your projector has the following key features:

• WUXGA native resolution projector delivering 18,000 ISO lumens.

• Support for Frame Sequential and Dual Pipe 3D formats as well as Frame Packed, Side-by-Side etc. formats.

• HDBaseT® for transmission of uncompressed High Denition Video up to 100 m from the source.

• 3G-SDI with loop-through.

• Blanking control for custom input window sizing.

• Edge Blending with black level correction.

• Cornerstone, Vertical & Horizontal Keystone, Pincushion & Barrel, and Image Rotation.

• Non-Linear warp for irregular projection surfaces.

• Separate control of screen and source aspect ratio.

• Contstant brightness mode maintains light output at selected levels.

• Control via LAN and RS232.

• Motorised lens mount.

A serial number is located on the side of the projector. Record it here:

Notes

page vi

Digital Projection M-Vision Laser 18K Series

Rev C December 2017

CONTENTS

INSTALLATION AND QUICK-START GUIDE ..............................1

WHAT’S IN THE BOX? ................................................................... 3

CONNECTING THE POWER SUPPLY ............................................. 4

PROJECTOR OVERVIEW ............................................................... 5

Front and rear views ............................................................................. 5

Control panel ......................................................................................... 6

Projector indicators ................................................................................ 7

REMOTE CONTROL ....................................................................... 8

Infrared reception ................................................................................ 11

POSITIONING THE SCREEN AND PROJECTOR ........................... 12

Roll and pitch ...................................................................................... 13

Stacking instructions ........................................................................... 14

CHANGING THE LENS ................................................................. 17

Inserting a new lens ............................................................................ 17

Removing the lens .............................................................................. 18

OPERATING THE PROJECTOR .................................................... 19

Switching the projector on ................................................................... 19

Switching the projector off ................................................................... 19

Selecting an input signal ..................................................................... 20

Selecting a test pattern ....................................................................... 20

Adjusting the lens ................................................................................ 21

Adjusting the image............................................................................. 21

CONNECTION GUIDE ............................................................................23

SIGNAL INPUTS AND OUTPUTS .................................................. 25

Digital inputs and outputs .................................................................... 25

EDID on the DisplayPort, HDMI and HDBaseT inputs ........................ 26

Using DisplayPort/HDMI/HDBaseT switchers with the projector ........ 26

3D connections ................................................................................... 27

Frame sequential 1080p and WUXGA 3D sources at 100 and 120 Hz ............... 27

Dual Pipe 1080p, WUXGA and WQXGA 3D sources at 100 and 120 Hz ............ 27

3D Sync............................................................................................... 28

3D Sync In ......................................................................................... 28

3D Sync Out ....................................................................................... 28

CONTROL CONNECTIONS ........................................................... 29

LAN connection examples .................................................................. 30

RS232 connection example ............................................................... 31

page vii

Digital Projection M-Vision Laser 18K Series

Rev C December 2017

OPERATING GUIDE ................................................................................33

USING THE MENUS ..................................................................... 35

Opening the OSD ................................................................................ 35

Opening a menu.................................................................................. 35

Exiting menus and closing the OSD.................................................... 35

Inside a menu...................................................................................... 36

Accessing sub-menus ........................................................................... 36

Executing commands............................................................................ 36

Editing projector settings ..................................................................... 37

Using a slider to set a value .................................................................... 37

Editing numeric values .......................................................................... 37

USING THE PROJECTOR ............................................................. 38

Main menu .......................................................................................... 38

Lens menu .......................................................................................... 39

Lens Control ....................................................................................... 39

Lens Memory ...................................................................................... 40

Image menu ........................................................................................ 41

Color menu.......................................................................................... 42

Color Space ....................................................................................... 42

Color Mode ........................................................................................ 43

Geometry menu .................................................................................. 48

Aspect Ratio ....................................................................................... 48

Digital Zoom ....................................................................................... 50

Overscan ........................................................................................... 51

Blanking ............................................................................................ 52

Keystone ........................................................................................... 53

4 Corners .......................................................................................... 55

Rotation ............................................................................................ 56

Pincushion / Barrel ............................................................................... 57

Arc ................................................................................................... 58

Custom Warp ..................................................................................... 58

Edge Blend menu................................................................................ 59

Blend Width........................................................................................ 60

Black Level Uplift ................................................................................. 61

3D menu.............................................................................................. 62

3D types ............................................................................................ 63

Some 3D settings explained ................................................................... 64

Laser menu ......................................................................................... 65

Setup menu ......................................................................................... 66

ColorMax Setting ................................................................................. 68

Power On/Off ...................................................................................... 69

Clock Adjust ....................................................................................... 70

OSD Settings ...................................................................................... 71

Memory ............................................................................................. 71

Network menu ..................................................................................... 72

PIP menu ............................................................................................ 73

Information menu ................................................................................ 74

Signal Format ..................................................................................... 74

System Status .................................................................................... 75

Thermal Status.................................................................................... 75

Factory Reset ..................................................................................... 76

CONTENTS (continued)

page viii

Digital Projection M-Vision Laser 18K Series

Rev C December 2017

REFERENCE GUIDE ................................................................................77

THE DMD™ .................................................................................. 79

CHOOSING A LENS ..................................................................... 81

Basic calculation ................................................................................. 82

Basic calculation example ................................................................... 83

Full lens calculation ............................................................................. 84

Introducing TRC .................................................................................. 84

Calculating TRC .................................................................................. 85

Calculating the throw ratio with TRC ......................................................... 86

Full lens calculation example .............................................................. 87

POSITIONING THE SCREEN AND PROJECTOR ........................... 88

POSITIONING THE IMAGE ........................................................... 89

FRAME RATES AND PULLDOWNS EXPLAINED ........................... 91

Interlaced and progressive scan ......................................................... 91

Frame rates of image sources ............................................................ 91

Pulldowns - conversion into destination formats ................................. 92

2:3 (normal) pulldown ........................................................................... 92

2:3:3:2 (advanced) pulldown ................................................................... 93

APPENDIX A: LENS PART NUMBERS .......................................... 94

APPENDIX B: SUPPORTED SIGNAL INPUT MODES .................... 95

2D formats........................................................................................... 95

3D formats........................................................................................... 98

APPENDIX C: WIRING DETAILS ................................................ 100

RS232 ............................................................................................... 100

Trigger 1 & Trigger 2 ......................................................................... 101

Wired remote control ......................................................................... 101

Sync IN and Sync OUT ..................................................................... 101

APPENDIX D: GLOSSARY OF TERMS ....................................... 102

CONTENTS (continued)

Digital Projection M-Vision Laser 18K Series

This page is intentionally left blank.

Rev C December 2017

M-Vision Laser 18K Series

High Brightness Digital Video Projector

INSTALLATION AND QUICK-START GUIDE

4

Digital Projection M-Vision Laser 18K Series

Installation and Quick-Start Guide

IN THIS GUIDE

Rev C December 2017

IN THIS GUIDE

WHAT’S IN THE BOX? .....................................................................................3

CONNECTING THE POWER SUPPLY ...........................................................4

PROJECTOR OVERVIEW .................................................................................5

Front and rear views ...................................................................................................5

Control panel ...............................................................................................................6

Projector indicators ........................................................................................................... 7

REMOTE CONTROL ..........................................................................................8

Infrared reception ......................................................................................................11

POSITIONING THE SCREEN AND PROJECTOR .....................................12

Roll and pitch ............................................................................................................13

Stacking instructions ................................................................................................14

CHANGING THE LENS ..................................................................................17

Inserting a new lens ..................................................................................................17

Removing the lens ....................................................................................................18

OPERATING THE PROJECTOR ...................................................................19

Switching the projector on .......................................................................................19

Switching the projector off .......................................................................................19

Selecting an input signal ..........................................................................................20

Selecting a test pattern .............................................................................................20

Adjusting the lens .....................................................................................................21

Adjusting the image ..................................................................................................21

page 3

Digital Projection M-Vision Laser 18K Series

Installation and Quick-Start Guide

WHAT’S IN THE BOX?

Rev C December 2017

What’s In The Box? Notes

Make sure your box contains

everything listed. If any pieces are

missing, contact your dealer.

You should save the original box

and packing materials, in case you

ever need to ship your projector.

The projector is shipped without a

lens.

Only one power cable - dependent

on the destination territory - will be

supplied with the projector.

A stacking kit is also provided in

some regions.

Remote control

Pic Mute

OFF ON

MENU

EXIT INFO

HDMI1

OK

OFF ON

ALT

LENS

FOCUS ZOOM

IN

OUT

IN

OUT

SHIFT

21 3

HDMI2 DVI

DISPLAYPORT

HD-T 3GSDI

VGA COMP1 COMP2

BRI

TEST

CON GAMMA

R G B ALL

3D EYE PIP SWAP

456

7 8 9 0

ALT

ADDR

OSD

OFF ON

DEFAULT

FREEZE RE-SYNC

A B C D

USER PRESET

2x AAA batteries

User Manual on disc Important Information

Power cable, Europe Power cable, North America

Projector

Power cable, United Kingdom Power cable, China

HDMI cable

page 4

Digital Projection M-Vision Laser 18K Series

Installation and Quick-Start Guide

CONNECTING THE POWER SUPPLY

Rev C December 2017

Connecting The Power Supply

Firmly push the mains connector into the socket 1, then press the ON/OFF switch 2.

Notes

Use only the power cable

provided.

Ensure that the power outlet

includes a ground connection as

this equipment MUST be earthed.

Handle the power cable carefully

and avoid sharp bends. Do not

use a damaged power cable.

When operating on 110V Light

output power is reduced by approx

35%.

1 2

page 5

Digital Projection M-Vision Laser 18K Series

Installation and Quick-Start Guide

PROJECTOR OVERVIEW

Rev C December 2017

Projector Overview

Front and rear views

1 Indicators: TEMP, LIGHT, STATUS and POWER

2 Lens mount

3 Air inlet

4 Lifting handle

5 Air inlet

6 Front infrared window

7 Stacking feet

8 Air outlet

9 Rear infrared window

10 Connections panel

11 Lifting handle

12 Control panel

13 Adjustable feet

14 Stacking feet

15 Mains socket and switch

Notes

Front view

5

3

2

1

7

6

4

Rear view

12108

14 1513

119

page 6

Digital Projection M-Vision Laser 18K Series

Installation and Quick-Start Guide

PROJECTOR OVERVIEW

Rev C December 2017

Control panel

1 POWER

Switches the projector on and off

(STANDBY).

2 INPUT

Switches to the next input source.

3 AUTO SYNC

Re-synchronises with the current input

signal.

4 ASPECT

Changes the aspect ratio.

5 CENTER LENS

Centers the lens.

6 PIC MUTE

Shows and hides the projected image.

When OFF, the light source is completely

switched off and the screen is black.

7 MENU

Displays and exits the OSD.

8 Arrow buttons & ENTER

Navigation buttons used to highlight menu

entries in the OSD.

Press ENTER to open or execute the

highlighted menu entry.

9 EXIT

Exits the current OSD page and enters the

level above.

10 LENS SHIFT arrow buttons

Each of these buttons moves the lens in the

specied direction.

11 FOCUS plus and minus buttons

Used to move the focus in and out.

12 ZOOM plus and minus buttons

Used to zoom in and out.

POWER

INPUT AUTO

SYNC ASPECT CENTER

LENS PIC MUTE

1 2 3 4 5 6

7 8 9 10 11 12

Notes

AUTO SYNC and ASPECT do not

work when the projector uses HDMI

3 or 4.

page 7

Digital Projection M-Vision Laser 18K Series

Installation and Quick-Start Guide

PROJECTOR OVERVIEW

Rev C December 2017

Projector indicators

TEMP. Off = no problem

Flashing red = temperature error

LIGHT Off = light is switched off

Flashing green = light is preparing to switch on

Flashing red (cycles of six ashes) = light module failure

On, green = light is switched on

STATUS Off = no problem

Flashing red (continuously) = cover error

Flashing red (cycles of four ashes) = fan error

On, red = system error

POWER Off = the projector is switched off

Flashing green = the projector is warming up

Flashing amber = the projector is cooling down

On, red = STANDBY mode

On, green = the projector is switched on

Notes

POWERSTAT USLIGHTTEMP.

page 8

Digital Projection M-Vision Laser 18K Series

Installation and Quick-Start Guide

REMOTE CONTROL

Rev C December 2017

Remote Control

1 Power ON / OFF

Turns power on and off.

2 Pic Mute OPEN / CLOSED

Shows and hides the projected image.

When CLOSED, the light source is completely switched off and the screen is black.

2 OSD ON / OFF

Enable and disable screen timeout messages and control whether to show the OSD

during projection.

4 MENU

Access the OSD. If the OSD is open, press this button to go back to the previous menu.

5 Navigation (arrows and OK)

Navigate through the menus with the arrows, conrm your choice with OK.

In lens adjustment modes, the arrows are used to move, zoom or focus the lens. See 11

below.

In lens adjustment modes, or when the OSD is not showing, the OK button switches

between modes: Shift Adjustment and Zoom / Focus Adjustment.

6 EXIT

Go up one level in the OSD. When the top level is reached, press to close the OSD.

7 FREEZE

Freeze the current frame.

8 DEFAULT

When editing a parameter, press this button to restore the default value.

9 INFO

Access information about the projector.

10 RE-SYNC

Re-synchronise with the current input signal.

continues on next page...

Pic Mute

OPEN CLOSE

MENU

EXIT INFO

HDMI1

OK

OFF ON

ALT

LENS

FOCUS ZOOM

IN

OUT

IN

OUT

SHIFT

21 3

HDMI2 DVI

DisplayPort1

HD-T 3GSDI

VGA COMP1 COMP2

HDMI3

TEST

HDMI4

DisplayPort2

R G B ALL

3D EYE PIP SWAP

456

7 8 9 0

ALT

ADDR

OSD

OFF ON

DEFAULT

FREEZE RE-SYNC

A B C D

USER PRESET

1

2

5

6

8

4

9

7

3

10

Notes

FREEZE and RE-SYNC are not

available when the projector uses

input HDMI 3 or 4.

This projector does not use the

following options on the remote:

DVI, VGA, COMP 1 and COMP 2.

Remote control

page 9

Digital Projection M-Vision Laser 18K Series

Installation and Quick-Start Guide

REMOTE CONTROL

Rev C December 2017

11 LENS adjustment

FOCUS IN / OUT: adjust focus.

SHIFT: press and hold this button, then use the Navigation arrow

buttons to move the lens.

ZOOM IN / OUT: adjust zoom.

12 USER PRESET A, B, C, D

Load user presets.

13 ALT

Press and hold this button to access alternative functions for all

buttons with a green label.

14 DVI / DisplayPort2 / numeric input 3

There is no DVI input on this projector.

Use with ALT to select the DisplayPort 2 input.

15 HDMI 2 / HDMI 4 / numeric input 2

Select the HDMI 1 input.

Use with ALT to select the HDMI 4 input.

16 HDMI 1 / HDMI 3 / numeric input 1

Select the HDMI 1 input.

Use with ALT to select the HDMI 3 input.

17 TEST / SWAP / numeric input 0

Show a test pattern. Press again to show the next test pattern:

...Off, White, Black, Red, Green, Blue, CheckerBoard,

CrossHatch, V Burst, H Burst, ColorBar...

When PIP mode is on, use this button with ALT to swap the main and

sub images.

continues on next page...

Notes

This projector does not use the

following options on the remote:

HDMI 3 and HDMI 4

DVI, VGA, COMP 1 and COMP 2.

Remote control

Pic Mute

OPEN CLOSE

MENU

EXIT INFO

HDMI1

OK

OFF ON

ALT

LENS

FOCUS ZOOM

IN

OUT

IN

OUT

SHIFT

21 3

HDMI2 DVI

DisplayPort1

HD-T 3GSDI

VGA COMP1 COMP2

HDMI3

TEST

HDMI4

DisplayPort2

R G B ALL

3D EYE PIP SWAP

456

7 8 9 0

ALT

ADDR

OSD

OFF ON

DEFAULT

FREEZE RE-SYNC

A B C D

USER PRESET

13

11

12

14

15

16

17

page 10

Digital Projection M-Vision Laser 18K Series

Installation and Quick-Start Guide

REMOTE CONTROL

Rev C December 2017

17 DISPLAYPORT 1 / R / numeric input 4

Select DisplayPort 1 input.

18 HD-T / G / numeric input 5

Select the HDBaseT input.

19 3GSDI / B / numeric input 6

Select the 3G-SDI input.

20 VGA / 3D / numeric input 7

There is no VGA input on this projector.

Use with ALT to toggle the 3D Format setting between Off and Auto.

21 COMP1 / EYE / numeric input 8

There is no Component 1 input on this projector.

Use with ALT to switch between left and right eye 3D dominance.

22 COMP2 / PIP / numeric input 9

There is no Component 2 input on this projector.

Use with ALT to switch on Picture In Picture (PIP) mode.

23 ADDR / ALL (with red indicator at the top)

Assign and unassign an IR remote address.

To assign an address:

1. Press and hold this button until the indicator starts ashing.

2. Release this button and while the indicator is still ashing, enter

a two-digit address using the numeric input buttons. The indicator

will ash three times quickly to conrm the change.

To unassign an address and return to the default address 00,

• Press and hold ALT and this button simultaneously until the

indicator ashes to conrm the change.

Notes

This projector does not use the

following options on the remote:

HDMI 3 and HDMI 4

DVI, VGA, COMP 1 and COMP 2.

Remote control bottom

Pic Mute

OPEN CLOSE

MENU

EXIT INFO

HDMI1

OK

OFF ON

ALT

LENS

FOCUS ZOOM

IN

OUT

IN

OUT

SHIFT

21 3

HDMI2 DVI

DisplayPort1

HD-T 3GSDI

VGA COMP1 COMP2

HDMI3

TEST

HDMI4

DisplayPort2

R G B ALL

3D EYE PIP SWAP

456

7 8 9 0

ALT

ADDR

OSD

OFF ON

DEFAULT

FREEZE RE-SYNC

A B C D

USER PRESET

23

18

19

17

20

21

22

Pic Mute

OPEN CLOSE

MENU

EXIT INFO

HDMI1

OK

OFF ON

ALT

LENS

FOCUS ZOOM

IN

OUT

IN

OUT

SHIFT

21 3

HDMI2 DVI

DisplayPort1

HD-T 3GSDI

VGA COMP1 COMP2

HDMI3

TEST

HDMI4

DisplayPort2

R G B ALL

3D EYE PIP SWAP

456

7 8 9 0

ALT

ADDR

OSD

OFF ON

DEFAULT

FREEZE RE-SYNC

A B C D

USER PRESET

Remote control top

Page is loading ...

Digital Projection M-Vision Laser 18K User manual

Digital Projection M-Vision Laser 18K User manual

Related papers

Other documents