Central Machinery Item 61483 Owner's manual

Brand: Central Machinery

Model: Item 61483

Category: Power tools

Type: Owner's manual

This manual is also suitable for

Page 2 For technical questions, please call 1-800-444-3353. Item 61483

SAFETY OPERATION MAINTENANCESETUP

Table of Contents

Safety ......................................................... 2

Specifications ............................................. 6

Setup .......................................................... 6

Operation .................................................... 9

Maintenance .............................................. 12

Parts List and Diagram .............................. 14

Warranty .................................................... 16

WARNING SYMBOLS AND DEFINITIONS

This is the safety alert symbol. It is used to alert you to potential personal injury hazards.

Obey all safety messages that follow this symbol to avoid possible injury or death.

Indicates a hazardous situation which, if not avoided,

will result in death or serious injury.

Indicates a hazardous situation which, if not avoided,

could result in death or serious injury.

Indicates a hazardous situation which, if not avoided,

could result in minor or moderate injury.

Addresses practices not related to personal injury.

IMPORTANT SAFETY INFORMATION

General Tool Safety Warnings

Read all safety warnings and instructions.

Failure to follow the warnings and instructions may result in electric shock, fire and/or serious injury.

Save all warnings and instructions for future reference.

1. KEEP GUARDS IN PLACE and in working order.

2. REMOVE ADJUSTING KEYS AND

WRENCHES. Form habit of checking to

see that keys and adjusting wrenches are

removed from tool before turning it on.

3. KEEP WORK AREA CLEAN.

Cluttered areas and benches invite accidents.

4. DON’T USE IN DANGEROUS ENVIRONMENT.

Don’t use power tools in damp or wet locations,

or expose them to rain. Keep work area well lighted.

5. KEEP CHILDREN AWAY. All visitors should

be kept safe distance from work area.

6. MAKE WORKSHOP KID PROOF with padlocks,

master switches, or by removing starter keys.

7. DON’T FORCE TOOL. It will do the job better

and safer at the rate for which it was designed.

8. USE RIGHT TOOL. Don’t force tool or attachment

to do a job for which it was not designed.

Page 3For technical questions, please call 1-800-444-3353.Item 61483

SAFETYOPERATIONMAINTENANCE SETUP

Table A: RECOMMENDED MINIMUM WIRE GAUGE

FOR EXTENSION CORDS

(120 VOLT)

NAMEPLATE

AMPERES

(at full load)

EXTENSION CORD

LENGTH

25′ 50′ 100′ 150′

0 – 6 18 16 16 14

6.1 – 10 18 16 14 12

10.1 – 12 16 16 14 12

12.1 – 16 14 12 Do not use.

9. USE PROPER EXTENSION CORD. Make sure your

extension cord is in good condition. When using

an extension cord, be sure to use one heavy

enough to carry the current your product will

draw. An undersized cord will cause a drop in line

voltage resulting in loss of power and overheating.

Table A shows the correct size to use depending

on cord length and nameplate ampere rating.

If in doubt, use the next heavier gauge.

The smaller the gauge number, the heavier the cord.

10. WEAR PROPER APPAREL. Do not wear

loose clothing, gloves, neckties, rings, bracelets,

or other jewelry which may get caught in moving

parts. Nonslip footwear is recommended.

Wear protective hair covering to contain long hair.

11. ALWAYS USE SAFETY GLASSES. Also use

face or dust mask if cutting operation is dusty.

Everyday eyeglasses only have impact resistant

lenses, they are NOT safety glasses.

12. SECURE WORK. Use clamps or a vise to hold

work when practical. It’s safer than using your

hand and it frees both hands to operate tool.

13. DON’T OVERREACH. Keep proper

footing and balance at all times.

14. MAINTAIN TOOLS WITH CARE. Keep

tools sharp and clean for best and safest

performance. Follow instructions for

lubricating and changing accessories.

15. DISCONNECT TOOLS before servicing;

when changing accessories, such as

blades, bits, cutters, and the like.

16. REDUCE THE RISK OF UNINTENTIONAL

STARTING. Make sure switch is in

off position before plugging in.

17. USE RECOMMENDED ACCESSORIES.

Consult the owner’s manual for recommended

accessories. The use of improper accessories

may cause risk of injury to persons.

18. NEVER STAND ON TOOL. Serious injury

could occur if the tool is tipped or if the

cutting tool is unintentionally contacted.

19. CHECK DAMAGED PARTS. Before further use

of the tool, a guard or other part that is damaged

should be carefully checked to determine that

it will operate properly and perform its intended

function – check for alignment of moving parts,

binding of moving parts, breakage of parts,

mounting, and any other conditions that may

affect its operation. A guard or other part that is

damaged should be properly repaired or replaced.

20. DIRECTION OF FEED. Feed work into

a blade or cutter against the direction of

rotation of the blade or cutter only.

21. NEVER LEAVE TOOL RUNNING UNATTENDED.

TURN POWER OFF. Don’t leave tool

until it comes to a complete stop.

General Tool Safety Warnings (cont.)

Page 4 For technical questions, please call 1-800-444-3353. Item 61483

SAFETY OPERATION MAINTENANCESETUP

Grounding Instructions

TO PREVENT ELECTRIC SHOCK AND DEATH FROM INCORRECT GROUNDING WIRE

CONNECTION

READ AND FOLLOW THESE INSTRUCTIONS:

110-120 V~ Grounded Tools: Tools with Three Prong Plugs

1. In the event of a malfunction or breakdown,

grounding provides a path of least resistance for

electric current to reduce the risk of electric shock.

This tool is equipped with an electric cord having an

equipment-grounding conductor and a grounding

plug. The plug must be plugged into a matching

outlet that is properly installed and grounded in

accordance with all local codes and ordinances.

2. Do not modify the plug provided – if it will

not fit the outlet, have the proper outlet

installed by a qualified electrician.

3. Improper connection of the equipment-grounding

conductor can result in a risk of electric shock.

The conductor with insulation having an outer

surface that is green with or without yellow

stripes is the equipment-grounding conductor.

If repair or replacement of the electric cord or

plug is necessary, do not connect the equipment-

grounding conductor to a live terminal.

4. Check with a qualified electrician or service

personnel if the grounding instructions are

not completely understood, or if in doubt as

to whether the tool is properly grounded.

5. Use only 3-wire extension cords that

have 3-prong grounding plugs and 3-pole

receptacles that accept the tool’s plug.

6. Repair or replace damaged or

worn cord immediately.

125 V~ 3-Prong Plug and Outlet

(for up to 125 V~ and up to 15 A)

Grounding

7. This tool is intended for use on a circuit that has

an outlet that looks like the one illustrated above in

125 V~ 3-Prong Plug and Outlet. The tool has a

grounding plug

that looks like the plug illustrated above

in 125 V~ 3-Prong Plug and Outlet.

8. The outlet must be properly installed and grounded

in accordance with all codes and ordinances.

9. Do not use an adapter to connect

this tool to a different outlet.

Drill Press Safety Warnings

For Your Own Safety Read Instruction

Manual Before Operating Drill Press

1. Wear eye protection.

2. Do not wear gloves, necktie, or loose clothing.

3. Clamp workpiece or brace against

Column to prevent rotation.

4. Use recommended speed for drill

accessory and workpiece material.

5. The included Chuck Key is specially designed

to be self-ejecting, reducing the risk of ejecting

at high speed. Only use the included Chuck

Key or an identical replacement key.

6. DO NOT OPERATE WITH ANY GUARD

DISABLED, DAMAGED, OR REMOVED. Moving

guards must move freely and close instantly.

7. The use of accessories or attachments not

recommended by the manufacturer may

result in a risk of injury to persons.

8. When servicing use only identical replacement parts.

9. Only use safety equipment that has been approved

by an appropriate standards agency. Unapproved

safety equipment may not provide adequate

protection. Eye protection must be ANSI-approved

and breathing protection must be NIOSH-approved

for the specific hazards in the work area.

Page 5For technical questions, please call 1-800-444-3353.Item 61483

SAFETYOPERATIONMAINTENANCE SETUP

10. Stay alert, watch what you are doing and use

common sense when operating a power tool.

Do not use a power tool while you are tired or

under the influence of drugs, alcohol or medication.

A moment of inattention while operating power

tools may result in serious personal injury.

11. Industrial applications must follow OSHA guidelines.

12. Maintain labels and nameplates on the tool.

These carry important safety information.

If unreadable or missing, contact

Harbor Freight Tools for a replacement.

13. Avoid unintentional starting.

Prepare to begin work before turning on the tool.

14. People with pacemakers should consult their

physician(s) before use. Electromagnetic fields in

close proximity to heart pacemaker could cause

pacemaker interference or pacemaker failure.

15. WARNING: Some dust created by power

sanding, sawing, grinding, drilling, and other

construction activities, contains chemicals

known [to the State of California] to cause

cancer, birth defects or other reproductive harm.

Some examples of these chemicals are:

• Lead from lead-based paints

• Crystalline silica from bricks and cement or other

masonry products

• Arsenic and chromium from

chemically treated lumber

Your risk from these exposures varies,

depending on how often you do this type of work.

To reduce your exposure to these chemicals:

work in a well ventilated area, and

work with approved safety equipment, such

as those dust masks that are specially

designed to filter out microscopic particles.

(California Health & Safety Code § 25249.5, et seq.)

16. WARNING: Handling the cord on this product will

expose you to lead, a chemical known to the State

of California to cause cancer, and birth defects or

other reproductive harm. Wash hands after handling.

(California Health & Safety Code § 25249.5, et seq.)

17. The warnings, precautions, and instructions

discussed in this instruction manual cannot

cover all possible conditions and situations

that may occur. It must be understood by the

operator that common sense and caution are

factors which cannot be built into this product,

but must be supplied by the operator.

Vibration Safety

This tool vibrates during use. Repeated or

long-term exposure to vibration may cause

temporary or permanent physical injury,

particularly to the hands, arms and shoulders. To

reduce the risk of vibration-related injury:

1. Anyone using vibrating tools regularly or for an

extended period should first be examined by a

doctor and then have regular medical check-ups

to ensure medical problems are not being caused

or worsened from use. Pregnant women or

people who have impaired blood circulation to

the hand, past hand injuries, nervous system

disorders, diabetes, or Raynaud’s Disease should

not use this tool. If you feel any medical or

physical symptoms related to vibration (such as

tingling, numbness, and white or blue fingers),

seek medical advice as soon as possible.

2. Do not smoke during use. Nicotine reduces

the blood supply to the hands and fingers,

increasing the risk of vibration-related injury.

3. Use tools with the lowest vibration when there

is a choice between different processes.

4. Include vibration-free periods each day of work.

5. Grip tool as lightly as possible (while still keeping

safe control of it). Let the tool do the work.

6. To reduce vibration, maintain the tool as

explained in this manual. If any abnormal

vibration occurs, stop use immediately.

SAVE THESE INSTRUCTIONS.

Drill Press Safety Warnings (cont.)

Page 6 For technical questions, please call 1-800-444-3353. Item 61483

SAFETY OPERATION MAINTENANCESETUP

Specifications

Spindle Speeds (RPM) 220, 290, 360, 430, 500, 570, 630, 760, 830, 920, 1430,

1620, 1850, 2260, 2580, 3600

Electrical Rating 120VAC, 60Hz, 7.2A, Single-Phase

Drill Chuck Capacity 7/64″ to 5/8″ (3mm to 16mm)

Spindle Stroke 3-1/8″

Spindle Taper MT2

Swing 13-1/2″

Column Diameter 2-3/4″

Table Size 11-3/8″ Diameter

Table Tilt 0º - 45º Left and Right

Table Rotation 360º

Overall Height 62-1/2″

Setup - Before Use:

Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the beginning of this

manual including all text under subheadings therein before set up or use of this product.

TO PREVENT SERIOUS INJURY FROM ACCIDENTAL OPERATION:

Turn the Power Switch of the tool off and unplug the tool from its electrical

outlet before performing any procedure in this section.

Note: For additional information regarding the parts listed in the following pages,

refer to the Assembly Diagram near the end of this manual.

Mounting

Before assembling and using the Drill Press,

secure the Base to a supporting structure.

1. Verify that the intended installation surface has no

hidden utility lines before drilling or driving screws.

2. Bolt the Base to a flat, level, solid floor

location capable of supporting the weight

of the Drill Press and any workpieces.

Assembly

Column Assembly to Base

1. With the Base (1) on a flat level surface, bolt on the

Column Support (2) using the four M10x30 Bolts

(5), Flat Washers (3) and Spring Washers (4).

2. Firmly tighten the Bolts.

3. Insert the Column (7) into its Support (2) and firmly

secure it with the Socket Head Cap Screws (6).

Note: It may be necessary to back the Cap

Screws out beforehand, as they may protrude

into the tube, preventing the Column from

sliding fully into the Column Support.

227541

Page 7For technical questions, please call 1-800-444-3353.Item 61483

SAFETYOPERATIONMAINTENANCE SETUP

Table and Support Arm to Column

1. Remove the Rack (8) from the Column (7)

by loosening the Collar Set Screw (19) and

removing the Collar (18). The Rack is stowed

in this position only for transit purposes.

2. Gently slide the Table Support Assembly over

the Column and hold it steady. With the long

smooth end of the Rack uppermost, insert the

Rack down through the Assembly so it meshes

with the gear inside the Assembly. Locate the

bottom end of the Rack in the groove formed

between the Column Support and the Column.

3. Hold the assembly and Rack in this position

while replacing the Collar on the Column, and

ensure that the top end of the Rack is firmly

engaged in the groove formed between the Collar

and the Column. IMPORTANT: Make sure

the Rack is not pinched and there is a working

clearance between the Rack and Collar.

4. Firmly secure the Collar to the Column

with the Collar Set Screw.

5. Tighten the Arm Locking Handle (23) to secure

the Table Support Assembly to the column.

6. Attach the Table Crank (30) to the

shaft protruding from the Table Support

and tighten its Securing Screw (29).

7. Loosen the Arm Locking Handle and turn the Crank,

testing to ensure that the Support Assembly easily

travels up and down the full length of the Rack

without binding, and that it also rotates freely all

the way around the Column without binding.

8. IF THE SUPPORT ASSEMBLY IS TOO TIGHT:

• Slightly loosen the Arm Locking Handle

and loosen the Collar Set Screw.

• Adjust the Collar slightly to provide a

greater working clearance between

the Rack and the Collar.

• Tighten the Collar Set Screw, and

test the assembly again.

9. Insert the Work Table (25) into its

housing on the Support Assembly and

secure with the Table Clamp (35).

Head to Column

1. It may be necessary to back the Set Screws

(6) out slightly to ensure they do not protrude

internally, as this would prevent the Head

Assembly from sliding fully into position.

2. With assistance, raise the Head assembly

and locate it on top of the Column.

3. Align the Head with the Base, and

firmly secure with the Set Screws.

4. Screw the three Spindle Feed Handle Bars (10)

firmly into the Spindle Feed Handle Seat (64).

Installing the Chuck

1. Loosen Arm Locking Handle (23) and slide the

Table up the Column to within 6″ of the Spindle

(42). Tighten the Arm Locking Handle.

2. Open the jaws of the Chuck (40) to their

maximum, using the supplied Chuck Key.

3. Put a piece of scrap wood on the

table to protect the Chuck nose.

4. Ensuring all parts are thoroughly clean, dry

and burr free, insert the Arbor (41) firmly

into the end of the Chuck with its pointed

end facing away from the Chuck.

5. With the Chuck now attached, insert the pointed end

of the Arbor into the end of the Spindle Shaft (42).

If necessary, rotate the Arbor to ensure that the

point on the end of the Arbor locates correctly

with the drive slot in the Spindle Shaft.

6. Using the Spindle Feed Handles (10),

lower the Spindle and press the Chuck nose

hard against the piece of scrap wood on the

Table to secure the Chuck into place.

Pulley Cover Knob

Attach the Pulley Cover Knob (91) to the

Pulley Cover (92). Screw on tightly.

Page 8 For technical questions, please call 1-800-444-3353. Item 61483

SAFETY OPERATION MAINTENANCESETUP

Installing the Drive Belts

1. Undo the Belt Tension Locking Knobs (14) on

both sides of the Head. Turn the Belt Tension

Lever (66) clockwise to bring the Motor Pulley

(74) towards the Spindle Pulley (52), allowing

the Belts to be easily slipped over the Pulleys.

2. Lubricate the Idler Pivot Shaft (86) and

Idler Pulley (87) with light grease, and install

the Pivot Shaft in its mounting between

the Motor Pulley and Spindle Pulley.

3. Consult the chart inside the pulley cover

(or Figure D on page 10), and install the

Belts (53, 88) in the positions corresponding

to the required spindle/drill speed.

4. Turn the Belt Tension Lever (66) counterclockwise

so that tension is applied to the belts.

IMPORTANT: Tension is correct when the belts

deflect by approximately 1/2″ at their centers of

run when using reasonable thumb pressure.

Deflection

Distance = 1/2"

Figure A

5. Use the Belt Tension Locking Knobs to

lock the Motor Pulley in this position.

Functions

Page 9For technical questions, please call 1-800-444-3353.Item 61483

SAFETYOPERATIONMAINTENANCE SETUP

Operating Instructions

Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the beginning of this

manual including all text under subheadings therein before set up or use of this product.

Tool Set Up

TO PREVENT SERIOUS INJURY FROM ACCIDENTAL OPERATION:

Turn the Power Switch of the tool off and unplug the tool from its electrical

outlet before performing any procedure in this section.

TO PREVENT SERIOUS INJURY: DO NOT OPERATE WITH ANY GUARD DISABLED,

DAMAGED, OR REMOVED. Moving guards must move freely and close instantly.

Table Adjustment

The Table is capable of moving in

four directions. See Figure B.

1. Raise or lower the Table by loosening the

Arm Locking Handle (A) and turning the

Table Crank (C): clockwise to raise the Table

and counterclockwise to lower the Table.

2. Swivel the Table around the column by loosening

the Arm Locking Handle. The table assembly, arm

and rack (B), move as one around the column.

3. Tilt the table by loosening the Bolt (E), and tilting the

Table to the required angle.

A scale (F) is provided on the arm to assist

in setting the required angle. For all normal

operations the Table angle should be set at 0°.

IMPORTANT: TO ENSURE THAT THE DRILL

IS ENTIRELY PERPENDICULAR TO THE

TABLE: Insert a piece of straight round bar in

the Chuck, place a square on the Table and

raise the table to bring the square up to the

round bar. Adjust the Table tilt if necessary

so that the Table is correctly aligned.

4. Spin the Table about its axis by loosening

the Table Locking Handle (D).

Figure B: Table Adjustments

Setting Drilling Depth

See Figure C.

Located around the Spindle Feed Shaft is a

Depth Stop Collar (A) carrying a graduated scale.

The Collar will turn around the Shaft, and can

be locked in place by a Lock Knob (B).

1. With the power to the Drill Press switched OFF, use

the Spindle Feed Handles to lower the drill until the

bit contacts the workpiece and hold it in that position.

2. Loosen the Lock Knob and turn the Collar so

that the measurement for the required hole

depth is aligned with the Pointer (C).

3. Tighten the Lock Knob to lock

the Collar in this position.

Figure C: Drill Depth Adjustment

Page 10 For technical questions, please call 1-800-444-3353. Item 61483

SAFETY OPERATION MAINTENANCESETUP

Changing Drill Speed

See Functions on page 8 for illustrations.

1. WARNING! TO PREVENT SERIOUS

INJURY: Turn off and unplug the Drill

Press before changing drill speed.

2. Open the Pulley Cover.

3. Loosen the Belt Tension Lock Knobs

on both sides of the Head and turn the

Belt Tension Lever clockwise. This will bring

the Motor Pulley towards the Spindle Pulley,

removing all tension from the drive Belts.

4. Consult Figure D (or the chart inside the

Pulley Cover) and install the Belts on the

Pulleys in the positions that correspond

to the required spindle/drill speed.

5. When the Belts have been correctly positioned,

tighten them by turning the Belt Tension Lever

counterclockwise. The tension is correct when

the belts deflect by approximately 1/2″ at their

centers of run when using reasonable thumb

pressure. (See Figure A on page 8.) Lock this

position in with the two Belt Tension Lock Knobs.

Note: If a belt is too long to be properly

tensioned, it must be replaced.

430

760

1620

3600

220

500

830

1850

290

570

920

2260

360

630

1430

2580

Figure D: Belt Speed Settings

The table above shows the belt arrangements for given drill speeds (A full

chart is also located on the inside of the pulley cover).

Installing the Bit

CAUTION! Wear heavy-duty work gloves to provide

protection when inserting and removing drill bits. Drill

bits become very hot during use. Do not remove a drill

bit until it has cooled.

1. Use the supplied Chuck Key to open the

jaws of the drill enough to fit the drill bit.

2. Insert the drill bit approximately 1″ into

the jaws of the Chuck, ensuring that the

jaws do not touch the flutes of the bit.

3. Hand tighten the Chuck until the bit is held

securely in place. Confirm that the bit is

centered between the Chuck jaws.

4. Use the Chuck Key to tighten the Chuck.

• Insert the tip of the Chuck Key into a hole on the

side of the Chuck so that the teeth on the Key

engage the gear on the Chuck. Use the Key to

tighten the Chuck securely and remove the Key.

NOTICE: Use sharp bits. Dull, bent, or damaged

bits will cause stress on the drill and/or break.

Page 11For technical questions, please call 1-800-444-3353.Item 61483

SAFETYOPERATIONMAINTENANCE SETUP

Workpiece and Work Area Set Up

1. Designate a work area that is clean and well-lit.

The work area must not allow access by children

or pets to prevent distraction and injury.

2. Route the power cord along a safe route to reach

the work area without creating a tripping hazard or

exposing the power cord to possible damage. The

power cord must reach the work area with enough

extra length to allow free movement while working.

3. Secure loose workpieces using a vise or clamps

(not included) to prevent movement while working.

4. There must not be objects, such as utility lines,

nearby that will present a hazard while working.

5. Set the Table height and position so

that the drill travel range is sufficient

for the workpiece to be drilled.

6. Set the drilling depth (see Setting Drilling

Depth on page 9) so that the bit will not

contact the table, or align the table so that

the hole in its center is in line with the bit.

7. Make sure the workpiece is securely clamped.

That is, held in a drill vise, or bolted to the table.

WARNING! Do not hold the workpiece

with your bare hands while drilling.

Serious injury may be caused if the workpiece

is flung out of the operator’s hand.

8. IF THE WORKPIECE IS IRREGULARLY SHAPED

and cannot be laid flat on the table, securely block

and clamp it. Any tilting, twisting or shifting will

result not only in a roughly drilled hole but also

increases the chances of damage to the drill.

9. FOR FLAT WORK, lay the workpiece on

a wooden base and clamp it down firmly

against the table to prevent it from turning.

10. FOR SMALL WORKPIECES that cannot be

clamped to the table, use a drill press vise (not

supplied). Clamp or bolt the vise to the table.

11. WHEN DRILLING COMPLETELY THROUGH

WOOD, position a piece of scrap wood

between the workpiece and the table to prevent

splintering on the underside of the workpiece

as the bit breaks through. Brace one end

of the scrap wood against the left side of

the column (see Figure E). Securely clamp

the other end of the scrap wood to the table.

Figure E: Bracing workpiece against column

General Operating Instructions

1. Use the Spindle Feed Handles to bring the drill bit

down to where the hole is to be drilled. Make minor

workpiece alignment adjustments as required.

2. Make sure that the Drill Press′ Power

Switch is in the ″Off″ position, then plug the

Power Cord into an electrical outlet.

3. Turn the Drill Press on.

4. Pull down on the Spindle Feed Handles and

slowly drill the hole into the workpiece.

WARNING! If the drill bit grabs and spins the workpiece,

do not attempt to stop the spinning with your hands.

Step back, and turn the Drill Press off. Wait for the

Spindle to stop turning before dislodging the workpiece.

5. To prevent accidents, turn off the tool and

disconnect its power supply after use. Clean, then

store the tool indoors out of children’s reach.

Page 12 For technical questions, please call 1-800-444-3353. Item 61483

SAFETY OPERATION MAINTENANCESETUP

Maintenance and Servicing

Procedures not specifically explained in this manual must

be performed only by a qualified technician.

TO PREVENT SERIOUS INJURY FROM ACCIDENTAL OPERATION:

Turn the Power Switch of the tool off and unplug the tool from its electrical

outlet before performing any procedure in this section.

TO PREVENT SERIOUS INJURY FROM TOOL FAILURE:

Do not use damaged equipment. If abnormal noise or vibration

occurs, have the problem corrected before further use.

Cleaning, Maintenance, and Lubrication

1. BEFORE EACH USE, inspect the general

condition of the tool. Check for:

• loose hardware,

• misalignment or binding of moving parts,

• cracked or broken parts,

• damaged electrical wiring, and

• any other condition that may

affect its safe operation.

2. AFTER USE, wipe external surfaces

of the tool with clean cloth.

WARNING! If the supply cord of this

power tool is damaged, it must be replaced

only by a qualified service technician.

Belt Inspection and Tensioning

1. Examine all belts for cracks, tears in

the backing, and other damage.

2. Replace a belt if damaged, following the instructions

under Installing the Drive Belts on page 8.

Page 13For technical questions, please call 1-800-444-3353.Item 61483

SAFETYOPERATIONMAINTENANCE SETUP

Troubleshooting

Problem Possible Causes Likely Solutions

Tool will not start. 1. Cord not connected.

2. No power at outlet.

3. Tool’s thermal reset breaker

tripped (if equipped).

4. Internal damage or wear. (Carbon

brushes or switch, for example.)

1. Check that cord is plugged in.

2. Check power at outlet. If outlet is unpowered,

turn off tool and check circuit breaker.

If breaker is tripped, make sure circuit is right

capacity for tool and circuit has no other loads.

3. Turn off tool and allow to cool. Press reset button on tool.

4. Have technician service tool.

Tool operates

slowly.

Extension cord too long or

wire size too small.

Eliminate use of extension cord. If an extension cord

is needed, use one with the proper diameter for its

length and load. See Table A on page 3.

Motor runs, but

Spindle does

not turn.

Belt(s) improperly installed or missing. Properly install belt(s). See Installing

the Drive Belts on page 8.

Performance

decreases

over time.

1. Accessory dull or damaged.

2. Carbon brushes worn or damaged.

3. Belt(s) are loose

1. Keep cutting accessories sharp. Replace as needed.

2. Have qualified technician replace brushes.

3. Properly tension belts. See Installing

the Drive Belts on page 8.

Excessive noise

or rattling.

1. Internal damage or wear. (Carbon

brushes or bearings, for example.)

2. Belts too loose (slipping) or too

tight (bearing damage).

1. Have technician service tool.

2. Properly tension belt(s). See Installing the Drive Belts on

page 8.

Overheating. 1. Forcing machine to work too fast.

2. Accessory dull or damaged.

3. Blocked motor housing vents.

4. Motor being strained by long or

small diameter extension cord.

1. Allow machine to work at its own rate.

2. Keep cutting accessories sharp. Replace as needed.

3. Wear ANSI-approved safety goggles and

NIOSH-approved dust mask/respirator while

blowing dust out of motor using compressed air.

4. Eliminate use of extension cord. If an extension cord

is needed, use one with the proper diameter for its

length and load. See Table A on page 3.

Follow all safety precautions whenever diagnosing or servicing

the tool. Disconnect power supply before service.

Record Product’s Serial Number Here:

Note: If product has no serial number, record month and year of purchase instead.

Note: Some parts are listed and shown for illustration purposes only,

and are not available individually as replacement parts.

PLEASE READ THE FOLLOWING CAREFULLY

THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY DIAGRAM

IN THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER OR DISTRIBUTOR

MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS

QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT, OR THAT HE OR SHE IS QUALIFIED TO REPLACE

ANY PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER AND/OR DISTRIBUTOR EXPRESSLY

STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTIFIED AND

LICENSED TECHNICIANS, AND NOT BY THE BUYER. THE BUYER ASSUMES ALL RISK AND LIABILITY

ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS

THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO.

Page 14 For technical questions, please call 1-800-444-3353. Item 61483

SAFETY OPERATION MAINTENANCESETUP

Parts List and Diagram

Parts List

Part Description Qty

1 Base 1

2 Column Support 1

3 Flat Washer 10 4

4 Spring Washer 10 4

5 Bolt M10×30 4

6 Socket Head Cap Screw M10×10 4

7 Column 1

8 Rack 1

9 Handle Knob 3

10 Spindle Feed Handle Bar 3

11 Spring Pin 5×30 1

12 Spindle Feed Shaft 1

13 Depth Stop Collar 1

14 Lock Knob 3

15 Scale Label 1

16 Rivet 2×3 4

17 Pointer 1

18 Collar 1

19 Collar Set Screw M8×10 1

20 Axis Pin 1

21 Helical Gear 1

22 Support 1

23 Arm Locking Handle 1

24 Handle Cover 1

25 Work Table 1

26 Socket Head Cap Screw M8×90 1

27 Handle Grip 1

28 Nut M8 2

29 Securing Screw M5×8 2

30 Table Crank 1

31 Worm Gear 1

32 Scale Label 1

33 “0 Degree″ Label 1

34 Support Arm 1

35 Table Locking Handle 1

36 Handle Cover 1

37 Socket Head Cap Screw M6×10 2

38 Flat Washer 16 1

39 Bolt M16×25 1

40 Drill Chuck 1

41 Arbor 1

42 Spindle 1

43 Ball Bearing 6005 3

44 Wedge Key 1

45 Collar Bushing 1

46 Rubber Ring 1

47 Ball Bearing 6003 2

48 Retainer Ring 16 1

49 Retainer Ring 47 2

50 Bearing Space Ring 1

51 Spindle Housing 1

52 Spindle Pulley 1

Part Description Qty

53 V-Belt O-685 1

54 Thin Nut M24×1.5 1

55 Tapping Screw T3.5×10 3

56 Switch 1

57 Flat Washer 5 3

58 Junction Box 1

59 Screw M4×8 4

60 Spring Washer 4 2

61 Wire 2

62 Tooth Washer 4 2

63 Round Pin 1

64 Spindle Feed Handle Seat 1

65 Handle Cover 1

66 Belt Tension Lever 1

67 Jackstay (A) 1

68 Flat Washer 12 4

69 Bolt M8×25 4

70 Washer 8 8

71 Motor Base Plate 1

72 Motor 1

73 Spring Washer 8 4

74 Motor Pulley 1

75 Nut M12 2

76 Spring Washer 12 2

77 Jackstay (B) 1

78 Pull Pin 1

79 Cam 1

80 Hex Head Cap Screw M6×12 1

81 Rubber Pad 4

82 Protective Pin 2

83 Wire Clamp (A) 1

84 Flat Washer 6 1

85 Cross-Shaped Screw M6×10 1

86 Pulley Adjusting 1

87 Idler Pulley 1

88 V-Belt O-625 1

89 Ball Bearing 6202 2

90 Retainer Ring 35 1

91 Pulley Cover Knob 1

92 Pulley Cover 1

93 Cross-Shaped Screw M5×12 1

94 Nut M6 2

95 Wire Clamp (B) 1

96 Plug Cord 1

97 Tension Spring 1

98 Spring Cap 1

99 Nut M10 2

100 Screw 1

101 Head 1

Page 15For technical questions, please call 1-800-444-3353.Item 61483

SAFETYOPERATIONMAINTENANCE SETUP

Assembly Diagram

100

101

Limited 90 Day Warranty

Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards,

and warrants to the original purchaser that this product is free from defects in materials and workmanship for the

period of 90 days from the date of purchase. This warranty does not apply to damage due directly or indirectly,

to misuse, abuse, negligence or accidents, repairs or alterations outside our facilities, criminal activity, improper

installation, normal wear and tear, or to lack of maintenance. We shall in no event be liable for death, injuries

to persons or property, or for incidental, contingent, special or consequential damages arising from the use of

our product. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the

above limitation of exclusion may not apply to you. THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER

WARRANTIES, EXPRESS OR IMPLIED, INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS.

To take advantage of this warranty, the product or part must be returned to us with transportation charges

prepaid. Proof of purchase date and an explanation of the complaint must accompany the merchandise.

If our inspection verifies the defect, we will either repair or replace the product at our election or we may

elect to refund the purchase price if we cannot readily and quickly provide you with a replacement. We will

return repaired products at our expense, but if we determine there is no defect, or that the defect resulted

from causes not within the scope of our warranty, then you must bear the cost of returning the product.

This warranty gives you specific legal rights and you may also have other rights which vary from state to state.

3491 Mission Oaks Blvd. • PO Box 6009 • Camarillo, CA 93011 • (800) 444-3353

Central Machinery Item 61483 Owner's manual

Brand: Central Machinery

Model: Item 61483

Category: Power tools

Type: Owner's manual

This manual is also suitable for

Download PDF

report

Central Machinery Item 61483 Owner's manual

This manual is also suitable for

Central Machinery Item 61483 Owner's manual

Related papers

Other documents