M
odel No. IMTL94106.2
Serial No.
CAUTION
Read all precautions and instruc
-
tions in this manual before using
this equipment. Save this man
-
ual for future reference.
Write the serial number in the
space above for future reference.
QUESTIONS?
As a manufacturer, we are com-
mitted to providing complete
customer satisfaction. If you
have questions, or if parts are
damaged or missing, PLEASE
CONTACT OUR CUSTOMER
SERVICE DEPARTMENT
DIRECTLY.
CALL TOLL-FREE:
1-800-753-4645
Mon.–Fri., 6 a.m.–6 p.m. MST
ON THE WEB:
www.iconservice.com
USER'S MANUAL
Serial Number
Decal
Visit our website at
www.weslo.com
new products, prizes,
fitness tips, and much more!
Visit our website at
www.jumpking.com
new products, prizes,
fitness tips, and much more!
Visit our website at
www.imagefitness.com
new products, prizes,
fitness tips, and much more!
V
Visit our website at
www.proform.com
new products, prizes,
fitness tips, and much more!
Visit our website at
www.healthrider.com
new products, prizes,
fitness tips, and much more!
Visit our website at
www.nordictrack.com
new products, prizes,
fitness tips, and much more!
V
TABLE OF CONTENTS
IMPORTANT PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
BEFORE YOU BEGIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
TREADMILL OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
HOW TO FOLD AND MOVE THE TREADMILL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22
TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23
EXERCISE GUIDELINES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25
PART LIST . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26
ORDERING REPLACEMENT PARTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Back Cover
LIMITED WARRANTY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Back Cover
Note: An EXPLODED DRAWING is attached in the center of this manual.
IMAGE is a registered trademark of ICON IP, Inc.
2
3
WARNING: T
o reduce the risk of burns, fire, electric shock, or injury to persons, read the
following important precautions and information before operating the treadmill.
1. It is the responsibility of the owner to ensure
t
hat all users of this treadmill are adequately
informed of all warnings and precautions.
2. Use the treadmill only as described in this
manual.
3. Place the treadmill on a level surface, with at
least eight feet of clearance behind it and two
feet on each side. Do not place the treadmill
on any surface that blocks air openings. To
protect the floor or carpet from damage, place
a mat under the treadmill.
4. Keep the treadmill indoors, away from mois-
ture and dust. Do not put the treadmill in a
garage or covered patio, or near water.
5. Do not operate the treadmill where aerosol
products are used or oxygen is administered.
6. Keep children under the age of 12 and pets
away from the treadmill at all times.
7. The treadmill should not be used by persons
weighing more than 350 pounds. Never allow
more than one person on the treadmill at a time.
8. Wear appropriate exercise clothes when
using the treadmill. Do not wear loose clothes
that could become caught in the treadmill.
Athletic support clothes are recommended
for both men and women.
Always wear ath
-
letic shoes. Never use the treadmill with bare
feet, wearing only stockings, or in sandals.
9. When connecting the power cord (see page 10),
plug the power cord into a surge suppressor
(not included) and plug the surge suppressor
into a grounded circuit capable of carrying 15
or more amps. No other appliance should be on
the same circuit. Do not use an extension cord.
10. Use only a single-outlet surge suppressor
that meets all of the specifications described
on page 10. To purchase a surge suppressor,
see your local IMAGE dealer or call the toll-
free telephone number on the front cover of
this manual and order part number 146148, or
see your local electronics store.
11. Failure to use a properly functioning surge
s
uppressor could result in damage to the con-
trol system of the treadmill. If the control sys-
tem is damaged, the walking belt may change
speed, accelerate, or stop unexpectedly,
which may result in a fall and serious injury.
12. Keep the power cord and the surge suppres-
sor away from heated surfaces.
13. Never move the walking belt while the power
is turned off. Do not operate the treadmill if
the power cord or plug is damaged, or if the
treadmill is not working properly. (See
BEFORE YOU BEGIN on page 6 if the tread-
mill is not working properly.)
14. Read, understand, and test the emergency
stop procedure before using the treadmill (see
TREADMILL OPERATION on page 10).
15. Never start the treadmill while you are stand-
ing on the walking belt. Always hold the
handrails while using the treadmill.
16. To protect the treadmill and TV during light-
ning storms, unplug the power cord from the
wall outlet and disconnect the cable system.
This will prevent damage due to lightning and
power line surges.
17. The treadmill is capable of high speeds.
Adjust the speed in small increments to avoid
sudden jumps in speed.
18.
The pulse sensor is not a medical device.
Various factors, including the user's move-
ment, may affect the accuracy of heart rate
readings. The pulse sensor is intended only
as an exercise aid in determining heart rate
trends in general.
19. Never leave the treadmill unattended while it
is running. Always remove the key, unplug
the power cord, and move the reset/off circuit
breaker to the “off” position when the tread
-
mill is not in use. (See the drawing on page 6
for the location of the circuit breaker.)
IMPORTANT PRECAUTIONS
20. Do not attempt to raise, lower, or move the
t
readmill until it is properly assembled. (See
ASSEMBLY on page 7, and HOW TO FOLD
A
ND MOVE THE TREADMILL on page 22.)
You must be able to safely lift 45 pounds (20
k
g) to raise, lower, or move the treadmill.
21. When folding or moving the treadmill, make
sure that the storage latch is fully closed.
22. Inspect and properly tighten all parts of the
treadmill every three months.
23. Never drop or insert any object into any open-
ing.
24.
DANGER: Always unplug the power
cord immediately after use, before cleaning
the treadmill, and before performing the main-
tenance and adjustment procedures de-
scribed in this manual. Never remove the
motor hood unless instructed to do so by an
authorized service representative. Servicing
other than the procedures in this manual
should be performed by an authorized service
representative only.
25. The treadmill is intended for in-home use
o
nly. Do not use the treadmill in any
commercial, rental, or institutional setting.
26. To reduce the risk of electric shock, do not
r
emove the cover or the back of the televi-
sion. There are no user serviceable parts in-
side. Refer servicing to qualified service per-
sonnel.
27. Upon completion of any service or repairs to
the treadmill or the television, ask the service
technician to perform safety checks to con-
firm that the unit is in proper operating con-
dition.
Note to CATV system installer: This reminder
is provided to call the CATV system in-
staller’s attention to Article 820-40 of the NEC
that provides guidelines for proper grounding
and, in particular, specifies that the cable
ground shall be connected to the grounding
system of the building, as close to the point
of cable entry as practical.
4
5
The decals shown here have been applied in the indicated locations. If a decal is miss-
ing, or if it is not legible, call the telephone number on the front cover of this man-
ual and request a free replacement decal. Apply the decal in the location shown.
Note: The decals are not shown at actual size.
50%
WARNING: Before beginning this or any exercise program, consult your physician. This
is especially important for persons over the age of 35 or persons with pre-existing health problems.
Read all instructions before using. ICON assumes no responsibility for personal injury or property
damage sustained by or through the use of this product.
SAVE THESE INSTRUCTIONS
P
ower Lines
Ground
Clamps
75 ohm Terminal
Service
Entrance
Equipment
Power Service Grounding
Electrode System (e.g.
Interior Metal Water Pipe)
Service
Entrance
Conductors
6
Congratulations for purchasing the IMAGE
®
AD-
VANCED 2200 treadmill. The ADVANCED 2200 tread-
mill offers an impressive array of features designed to
h
elp you achieve your fitness goals in the convenience
o
f your home. From the advanced console to the cush-
ioned walking platform, the ADVANCED 2200 treadmill
is designed to make each workout more effective and
enjoyable. And when you’re not exercising, the tread-
mill can be folded away, taking less than half the floor
space of conventional treadmills.
For your benefit, read this manual carefully before
you use the treadmill.
If you have questions after
reading this manual, please see the front cover of this
manual. To help us assist you, note the product model
number and serial number before contacting us. The
model number of the treadmill is IMTL94106.2. The se-
r
ial number can be found on a decal attached to the
t
readmill (see the front cover of this manual for the lo-
cation).
To avoid a registration fee for any service needed
under warranty, you must register the treadmill at
www.iconservice.com/registration.
Before reading further, please review the drawing
below and familiarize yourself with the labeled parts.
BEFORE YOU BEGIN
Handrail
Console
Television Screen
Tray
Key/Clip
Reset/Off
Circuit Breaker
Walking Belt
Foot Rail
Adjustable Cushioned
Walking Platform (see page 20)
Power Cord
RIGHT SIDE
Rear Roller
Adjustment Bolts
Fan
Handgrip Pulse Sensor
7
ASSEMBLY
To hire an authorized service technician to assemble the treadmill, call toll-free 1-800-445-2480. Assembly
r
equires two persons.
P
lace the treadmill in a cleared area and remove all packing materials. Do not
dispose of the packing materials until the treadmill is assembled.
Note: The underside of the treadmill walking belt is coated with high-performance lubricant. During shipping, a
s
mall amount of lubricant may be transferred to the top of the walking belt, the sides of the walking platform, or
the shipping carton. This does not affect treadmill performance. If there is lubricant on top of the walking belt or
on the sides of the walking platform, wipe off the lubricant with a soft cloth and a mild, non-abrasive cleaner.
Assembly requires a phillips screwdriver and the included hex key . To avoid
damaging plastic parts, do not use power tools for assembly.
1. With the help of a second person, carefully raise the
Uprights (65) to a vertical position.
Have the second person hold the console assembly near
the Uprights (65) as shown. Look under the console as-
sembly and locate the Console Wire Harness (71) and the
console TV cable.
Cut the plastic ties securing the Upright Wire Harness
(85) and the Upright TV Cable (100) to the Uprights (65).
Connect the Upright TV Cable to the console TV cable.
Connect the Upright Wire Harness to the Console Wire
Harness (71).
Make sure to connect the connectors
properly (see the inset drawing). The connectors
should slide together easily and snap into place. If the
connectors do not slide together easily and snap into
place, turn one connector and try again. IF THE CON-
NECTORS ARE NOT CONNECTED PROPERLY, THE
CONSOLE MAY BE DAMAGED WHEN THE POWER IS
TURNED ON.
65
65
85
100
Console TV Cable
71
1
2. Insert the slack in the Wire Harnesses (71, 85) and the
console TV cable into the Uprights (65).
Set the console assembly on the Uprights (65). While a
second person holds the console assembly, attach the
console assembly with four 1” Console Bolts (133) and
four Console Washers (69) as shown. Firmly tighten the
Console Bolts.
Console
Assembly
Console Assembly
69
71, 85
69
133
133
65
65
2
85
71
69
133
8
68
5
Collar
Spring
114
55
Knob
132
3
Small
Holes
3. With the help of a second person, raise the treadmill
F
rame (55). Hold the Latch Housing (68) and the Latch
Housing Cover (5) against the sides of the Frame as
shown. Loosely thread the two blunt-tipped 1/2” Screws
(132) into the Latch Housing Cover and the Latch Housing
as shown. Do not tighten the Screws yet.
Remove the knob from the pin. Make sure that the collar
a
nd the spring are on the pin. The collar should be on the
side of the spring shown. Insert the pin into the Latch
Housing (68), and tighten the knob back onto it.
Align the pin with the hole in the Left Handgrip (3) by slid-
ing the Latch Housing (68) up or down. Make sure that the
pin can be inserted fully into the hole. Hold the Latch
Housing in place as you tighten two 1/2” Tek Screws (114)
into the Latch Housing and the Frame (55). Then, tighten
the 1/2” Screws (132). Note: It may be necessary to pull
on the knob to access and tighten the Screws.
5. Make sure that all parts are properly tightened before you use the treadmill. Place a mat beneath the
treadmill to protect the floor or carpet. Note: Extra hardware may be included. Keep the included hex key
in a secure place; the hex key is used to adjust the walking belt (see pages 23 and 24). For your benefit, we
recommend that you familiarize yourself with the TROUBLESHOOTING section on pages 23 and 24.
Hole
Pin
3
114
132
4. Note the location of the 75 ohm terminal near the power
cord. For the television to operate properly, a CATV cable
must be connected to the 75 ohm terminal (see page 9).
4
75 Ohm Terminal
HOW TO CONNECT A 75 OHM CATV CABLE
1. Connect a 75 ohm
C
ATV cable to the 75
ohm terminal near the
power cord.
HOW TO CONNECT AN EXTERNAL SOURCE
USING A CATV CABLE
1
. Connect one end of a 75 ohm CATV cable to the 75
ohm output jack on your external source.
2. Plug in the power cord of your external source. See
your external source’s user’s manual for proper
grounding instructions.
3. Connect the 75 ohm CATV cable to the 75 ohm ter-
minal near the power cord.
9
75 Ohm Terminal
75 Ohm CATV Cable
Before operating the television, you must connect a 75 ohm CATV cable to the 75 ohm terminal on the
treadmill. Note: Use a CATV cable to connect to an external source such as a cable box, analog cable, satellite
T
V box, or VCR. No CATV cable is included.
10
THE PRE-LUBRICATED WALKING BELT
Your treadmill features a walking belt coated with high-
performance lubricant.
IMPORTANT: Never apply sil-
i
cone spray or other substances to the walking
belt or the walking platform. Such substances will
deteriorate the walking belt and cause excessive
wear.
HOW TO PLUG IN THE POWER CORD
Your treadmill, like any other type of sophisticated
electronic equipment, can be seriously damaged by
sudden voltage changes in your home’s power.
Voltage surges, spikes, and noise interference can
result from weather conditions or from other appliances
being turned on or off. To decrease the possibility of
your treadmill being damaged, always use a surge
suppressor with your treadmill (see drawing 1 at
the right). To purchase a surge suppressor, see
your local IMAGE dealer or call the toll-free tele-
phone number on the front cover of this manual
and order part number 146148, or see your local
electronics store.
Use only a single-outlet surge suppressor that is
UL 1449 listed as a transient voltage surge sup-
pressor (TVSS). The surge suppressor must have a
UL suppressed voltage rating of 400 volts or less
and a minimum surge dissipation of 450 joules.
The surge suppressor must be electrically rated for
120 volts AC and 15 amps. There must be a moni
-
toring light on the surge suppressor to indicate
whether it is functioning properly. Failure to use a
properly functioning surge suppressor could result
in damage to the control system of the treadmill. If
the control system is damaged, the walking belt
may change speed, accelerate or stop unexpect-
edly, which may result in a fall and serious injury.
This product must be grounded. If it should malfunc-
tion or break down, grounding provides a path of least
resistance for electric current to reduce the risk of elec
-
tric shock. This product is equipped with a cord having
an equipment-grounding conductor and a grounding
plug.
Plug the power cord into a surge suppressor,
and plug the surge suppressor into an appropriate
o
utlet that is properly installed and grounded in
accordance with all local codes and ordinances.
Important: The treadmill is not compatible with
GFCI-equipped outlets.
This product is for use on a nominal 120-volt circuit,
and has a grounding plug that looks like the plug illus-
trated in drawing 1 below. A temporary adapter that
looks like the adapter illustrated in drawing 2 may be
used to connect the surge suppressor to a 2-pole
receptacle as shown in drawing 2 if a properly
grounded outlet is not available.
The temporary adapter should be used only until a
properly grounded outlet (drawing 1) can be installed
by a qualified electrician.
The green-colored rigid ear, lug, or the like extending
from the adapter must be connected to a permanent
ground such as a properly grounded outlet box cover.
Whenever the adapter is used it must be held in place
by a metal screw.
Some 2-pole receptacle outlet box
covers are not grounded. Contact a qualified elec-
trician to determine if the outlet box cover is
grounded before using an adapter.
DANGER: Improper connection
of the equipment-grounding conductor can
result in an increased risk of electric shock.
Check with a qualified electrician or service-
man if you are in doubt as to whether the
product is properly grounded. Do not modify
the plug provided with the product—if it will
not fit the outlet, have a proper outlet
installed by a qualified electrician.
1
2
Grounded Outlet Box
Grounded Outlet Box
Grounding Plug
Surge Suppressor
Surge Suppressor
Grounding Pin
Adapter
Lug
Metal Screw
Grounded Outlet
Grounding Pin
TREADMILL OPERATION
1
1
ETRB13305
(RBTL13305)
FEATURES OF THE CONSOLE
The treadmill console offers an impressive array of
features designed to help you get the most from your
workouts.
When the manual mode of the console is selected, the
speed and incline of the treadmill can be changed with
the touch of a button. As you exercise, the console
will display continuous exercise feedback. You can
even measure your heart rate using the handgrip pulse
sensor.
In addition, the console offers ten preset programs.
Each program automatically controls the speed and in-
cline of the treadmill as it guides you through an effec-
tive workout. You can even create custom workout pro-
grams and store them in memory for future use.
Four heart rate programs are also offered. Each pro
-
gram automatically adjusts the speed and incline of the
treadmill to keep your heart rate near target heart rate
settings while you exercise.
Whether you select the manual mode or a program,
you can enjoy the shows of your choice on the per-
sonal television while you get in shape.
To use the manual mode of the console, follow the
steps beginning on page 12. To use a preset program,
see page 14. To create and use a custom program,
see pages 16 and 17. To use a heart rate program,
see page 18.
To operate the personal television, see
page 20.
Note: If there is a sheet of clear plastic on the face of
the console, peel off the plastic. To prevent damage to
the walking platform, wear clean athletic shoes while
using the treadmill. The first time the treadmill is used,
observe the alignment of the walking belt, and center
the walking belt if necessary (see page 24).
Clip
Key
12
H
OW TO TURN ON THE POWER
IMPORTANT: If the treadmill has been exposed to
c
old temperatures, allow it to warm to room tem-
perature before turning on the power. If you do not
do this, the console displays or other electrical
components may become damaged.
Plug in the power cord
(see page 10). Next, lo-
cate the reset/off circuit
breaker near the power
cord. Make sure that the
circuit breaker is in the
reset position.
Stand on the foot rails of the treadmill. Find the clip at-
tached to the key (see the drawing on page 11) and at-
tach the clip securely to the waistband of your clothes.
N
ext, insert the key into the console. After a moment,
the displays will light, and after a few seconds, the
television will turn on.
Important: In an emergency
situation, the key can be pulled from the console,
causing the walking belt to slow to a stop. Test the
clip by carefully taking a few steps backward until
the key is pulled from the console. If the key is not
pulled from the console, adjust the position of the
clip as needed.
HOW TO USE THE MANUAL MODE
Insert the key into the console.
See HOW TO TURN ON THE POWER above.
Select the manual mode.
When the key is inserted, the manual mode will be
selected. If you have selected a program, press
the Manual button to reselect the manual mode.
Start the walking belt.
To start the walking belt, press the Start button,
the Speed increase button, or one of the twelve
numbered Speed buttons.
If the Start button or the Speed increase button is
pressed, the walking belt will begin to move at 1
mph. As you exercise, change the speed of the
walking belt as desired by pressing the Speed in-
crease and decrease buttons. Each time a button
is pressed, the speed setting will change by 0.1
mph; if a button is held down, the speed setting
will change in increments of 0.5 mph. Note: After
t
he buttons are pressed, it may take a moment for
the walking belt to reach the selected speed setting.
If one of the numbered Speed buttons is pressed,
the walking belt will gradually increase in speed
until it reaches the selected speed setting.
To stop the walking belt, press the Stop button.
The time will begin to flash in the left display. To
restart the walking belt, press the Start button, the
Speed increase button, or one of the numbered
Speed buttons.
Change the incline of the treadmill as desired.
To change the incline of the treadmill, press the
Incline buttons. Each time a button is pressed, the
incline will change by 0.5%. To change the incline
setting quickly, press the numbered Incline buttons.
Note: After the buttons are pressed, it may take a
moment for the treadmill to reach the selected in-
cline setting.
Follow your progress with the displays.
The left display—This display will show the
elapsed time, your pace (in minutes per mile), and
the incline level of the treadmill
.
Note: When a pro-
gram is selected, this display will show the time
remaining in the program instead of the elapsed
time. Each time the incline of the treadmill
changes, the display will show the incline setting
for several seconds.
The left display will also show a training zone bar
that indicates the approximate intensity of your ex-
ercise. For example, if four to six segments of the
bar appear, the bar shows that your exercise inten-
sity is ideal for weight loss.
When the manual mode is selected, the left display
will also show a track. As you exercise,
the indica
-
tors around the
track will appear in succession
until the entire track is lit. The track will then dis-
appear the indicators will again begin to appear in
succession.
5
4
3
2
1
Reset
Position
Training Zone Bar
Track
13
The right display—This display will show the dis-
tance that you have walked or run, the number of
1
/4-mile laps you have completed, the speed of
the walking belt, and the approximate numbers of
c
alories
a
nd
f
at calories
y
ou have burned (see
FAT BURNING on page 25).
The right display will also show your heart rate
when you use the handgrip pulse sensor. In addi-
tion, during heart rate programs the right display
will show a heart rate bar that shows your heart
rate as a percentage of your estimated maximum
heart rate (see step 2 on page 18 for an explana-
tion of your estimated maximum heart rate). For
example, if four to six segments of the bar appear,
your heart rate is between 60% and 70% of your
estimated maximum heart rate.
Note: The console can display speed and dis-
tance in either miles or kilome
ters. The letters
“MPH” or “Km/H” will appear in the right display to
show which unit of measurement is selected. To
change the unit of measurement, see HOW TO
USE THE INFORMATION MODE on page 20.
For
simplicity, all instructions in this section refer
to miles.
To reset the displays, press the Stop button, re
-
move the key, and then reinsert the key.
Measure your heart rate if desired.
Before using
the handgrip
pulse sensor,
remove the
sheets of clear
plastic from the
metal contacts.
In addition,
make sure that your hands are clean. Next, hold
the handgrip pulse sensor with your palms resting
o
n the metal contacts;
a
void moving your hands
.
When your pulse is detected, the heart-shaped in-
d
icator in the right display will flash each time your
heart beats, one or two dashes (– –) will appear,
and then your heart rate will be shown.
For the
most accurate heart rate reading, continue to
hold the contacts for about 15 seconds.
Note: The handgrip pulse sensor is intended to be
used only for heart rate measurement.
Do not
use the handgrip pulse sensor as a handlebar.
Always hold the handrails for support when
you are not measuring your heart rate.
Turn on the fan if desired.
To turn on the fan, press the button below the fan.
To turn on the fan at high speed, press the button
a second time. To turn off the fan, press the but-
ton a third time. Note: If the fan is on when the
walking belt is stopped, the fan will automatically
turn off after a few minutes.
When you are finished exercising, remove the
key from the console.
Step onto the foot rails, press the Stop button, and
adjust the incline of the treadmill to the lowest
setting. The incline must be at the lowest setting
when the treadmill is folded to the storage posi-
tion or the treadmill will become damaged. Next,
remove the key from the console and put it in a se-
cure place. Note: If the displays remain lit after
the key is removed, the console is in the
“demo” mode. See HOW TO USE THE INFOR-
MATION MODE on page 20 and turn off the
demo mode.
When you are finished using the treadmill
,
switch the reset/off circuit breaker to the “off”
position and unplug the power cord.
8
7
6
Heart Rate Bar
Contacts
14
H
OW TO USE A PRESET PROGRAM
Insert the key into the console.
See HOW TO TURN ON THE POWER on
p
age 12.
Select a preset program.
To select a preset program, press the Speed &
Incline Programs button repeatedly. The right dis-
play will show which preset program (P-1 through
P-10) is selected.
When a preset program is selected, the left dis-
play will flash the maximum incline setting of the
program for a few seconds, and the right display
will flash the maximum speed setting. The left dis-
play will then show how long the program will last.
In addition, the first ten speed settings of the pro-
gram will appear in the matrix in the left display.
Press the Start button or the Speed increase
button to start the program.
A moment after the button is pressed, the tread-
mill will automatically adjust to the first speed and
incline settings of the program. Hold the handrails
and begin walking.
Each program is divided into several one-minute
segments. One speed setting and one incline set-
ting are programmed for each segment. Note: The
same speed setting and/or incline setting may be
programmed for two or more consecutive seg
-
ments.
The speed setting for the
first segment will be
s
hown in the flashing
Current Segment column
o
f the matrix. (The in-
cline settings are not
shown in the matrix.)
The speed settings for
the next seven segments
will be shown in the columns at the right.
When only three seconds remain in the first seg-
ment of the program, both the Current Segment
column and the column to the right will flash, and
a series of tones will sound. If the speed and/or in-
cline of the treadmill is about to change, the left
display and/or the right display will flash to alert
you. When the first segment ends,
all speed set-
tings in the matrix will move one column to the
left
. The speed setting for the second segment will
then be shown in the flashing Current Segment
column, and the treadmill will automatically adjust
to the speed and incline settings for the second
segment. Note: If all of the indicators in the
Current Segment column are lit after the speed
settings have moved to the left,
the speed settings
may move downward
so that only the highest indi-
cators appear in the matrix. If some indicators in
the Current Segment column are not lit when the
speed settings move to the left again, the speed
settings will move back up.
The program will continue in this way until the
speed setting for the last segment is shown in the
Current Segment column and the last segment
ends. The walking belt will then slow to a stop.
If the speed or incline setting is too high or too low
at any time during the program, you can manually
override the setting by pressing the Speed or
Incline buttons. Every few times a Speed button is
pressed, an additional indicator will appear or dis-
appear in the Current Segment column. (If any of
the columns to the right of the Current Segment
column have the same number of indicators as the
Current Segment column, an additional indicator
may appear or disappear in those columns as
well.) Note: When the next segment of the pro-
gram begins, the treadmill will automatically
adjust to the speed and incline settings for the
next segment.
3
2
1
Current Segment
Column
Matrix
15
To stop the program at any time, press the Stop
button. The time will begin to flash in the left dis-
p
lay. To restart the program, press the Start button
or the Speed increase button. The walking belt will
b
egin to move at 1 mph. When the next segment
of the program begins, the treadmill will automati-
cally adjust to the speed and incline settings for the
next segment.
Follow your progress with the displays.
See step 5 on pages 12 and 13.
Measure your heart rate if desired.
See step 6 on page 13.
Turn on the fan if desired.
See step 7 on page 13.
When you are finished exercising, remove the
key from the console.
When the program ends, make sure that the in-
cline of the treadmill is at the lowest setting.
Next, remove the key from the console and put it in
a secure place. Note: If the displays and various
indicators remain lit after the key is removed,
the console is in the “demo” mode. See HOW
TO USE THE INFORMATION MODE on page 20
and turn off the demo mode.
When you are finished using the treadmill,
switch the reset/off circuit breaker to the “off”
position and unplug the power cord.
7
6
5
4
16
H
OW TO CREATE A CUSTOM PROGRAM
I
nsert the key into the console.
S
ee HOW TO TURN ON THE POWER on
page 12.
Select a custom program.
To select a custom program, press the Custom
Programs button repeatedly until “P-15” or “P-16”
appears in the right display.
If the custom program has not yet been defined,
three columns of indicators will appear in the ma-
trix in the left display. If more than three
columns of indicators appear, see HOW TO
USE A CUSTOM PROGRAM on page 17.
Press the Start button or the Speed increase
button
and program the desired speed and in-
cline settings.
A moment after the button is pressed, the walking
belt will begin to move. Hold the handrails and
begin walking.
See the matrix in the left
display. Each custom
p
rogram is divided into
one-minute segments.
O
ne speed setting and
one incline setting can
be programmed for each
segment. The speed set-
ting for the first segment
will be shown in the flashing Current Segment col-
umn of the matrix. (The incline settings are not
shown in the matrix.) To program a speed setting
and an incline setting for the first segment, simply
adjust the speed and incline of the treadmill as de-
sired by pressing the Speed and Incline buttons.
Every few times a Speed button is pressed, an
additional indicator will appear or disappear in the
Current Segment column.
When the first segment of the program ends, the
current speed setting and the current incline set-
ting will be stored in memory.
The three columns
of indicators will then move one column to the left,
and the speed setting for the second segment will
be shown in the flashing Current Segment column.
Program a speed setting and an incline setting for
the second segment as described above.
Continue programming speed and incline settings
for as many segments as desired; custom pro-
grams can have up to forty segments. When you
are finished with your workout, press the Stop but-
ton twice. The speed and incline settings that you
have programmed and the number of segments
that you have programmed will then be saved in
memory.
When you are finished exercising, remove the
key from the console.
See step 7 on page 15.
4
3
2
1
Matrix
Current Segment
Column
17
H
OW TO USE A CUSTOM PROGRAM
I
nsert the key into the console.
S
ee HOW TO TURN ON THE POWER on
page 12.
Select a custom program.
To select a custom program, press the Custom
Programs button repeatedly until “P-15” or “P-16”
appears in the right display.
When a custom program is selected, the left dis-
play will flash the maximum incline setting of the
program for a few seconds, and the right display
will flash the maximum speed setting. The left dis-
play will then show how long the program will last.
In addition, the first ten speed settings of the pro-
gram will appear in the matrix in the left display.
Note: If only three columns of indicators ap-
pear, see HOW TO CREATE A CUSTOM PRO-
GRAM on page 16.
Press the Start button or the Speed increase
button to start the program.
A moment after the button is pressed, the tread-
mill will automatically adjust to the first speed and
incline settings that you programmed previously.
Hold the handrails and begin walking.
Each program is divided into several one-minute
segments. One speed setting and one incline set-
ting are programmed for each segment. The
speed setting for the first segment will be shown in
the flashing Current
Segment column of the
matrix. (The incline set-
tings are not shown in
the matrix.) The speed
settings for the next
several
segment
s will
be shown in the
columns to the right.
When only three seconds remain in the first seg-
ment of the program, both the Current Segment
column and the column to the right will flash, a se
-
ries of tones will sound, the speed setting and the
incline setting will flash in the displays, and
all
s
peed settings will move one column to the left.
The speed setting for the second segment will then
b
e shown in the flashing Current Segment column
and the treadmill will automatically adjust to the
second speed and incline settings that you pro-
grammed previously.
The program will continue until the speed setting
for the last segment is shown in the Current
Segment column and the last segment ends. The
walking belt will then slow to a stop.
If desired, you can redefine the program while
using it.
To change the speed or incline setting
during the current segment, simply press the
Speed or Incline buttons. When the current segment
ends, the new setting will be saved in memory. To
increase the length of the program,
first wait until
the program ends. Then, press the Start button, and
program speed and incline settings for as many ad-
ditional segments as desired. When you have
added as many segments as desired, press the
Stop button twice.
To decrease the length of the
program, press the Stop button twice at any time
before the program ends.
To stop the program at any time, press the Stop
button. The time will begin to flash in the left dis-
play. To restart the program, press the Start but-
ton or the Speed increase button.
Follow your progress with the displays.
See step 5 on pages 12 and 13.
Measure your heart rate if desired.
See step 6 on page 13.
Turn on the fan if desired.
See step 7 on page 13.
When you are finished exercising, remove the
key from the console.
See step 7 on page 15.
7
6
5
4
3
2
1
Current Segment
Column
18
H
OW TO USE A HEART RATE PROGRAM
Follow the steps below to use a heart rate program.
Insert the key into the console.
See HOW TO TURN ON THE POWER on
page 12.
Select a heart rate program.
To select a heart rate program, press the Heart
Rate Control Programs button repeatedly until
“P-11,” “P-12,” “P-13,” or “P-14” appears in the
right display.
If heart rate program 11 is selected, a pulse
symbol will scroll across the matrix in the left dis-
play. If heart rate program 12, 13, or 14 is se-
lected, a profile of the target heart rate settings of
the program will appear in the matrix in the left
display.
Note: During heart rate program 11, your heart
rate will remain near a target heart rate setting
that you select
.
During heart rate programs 12,
13, or 14, your heart rate will reach approximately
85% of your
estimated maximum heart rate.
Note:
Your maximum heart rate is estimated by sub-
tracting your age from 220. For example, if you
are 30 years old, your estimated maximum heart
rate is 190 beats per minute (220 – 30 = 190).
E
nter your age.
When a heart rate program is selected, the word
“AGE” and the current age setting will begin to
f
lash in the right display. If you have already en-
tered your age, press the Enter button. If you have
not entered your age, press the + or – button be-
side the Enter button to enter your age, and then
p
ress the Enter button.
Enter a target heart rate setting for the program.
If heart rate program 11 is selected,
the letters
“PLS” and the target heart rate setting for the pro-
gram will begin to flash in the right display. If de-
sired, change the target heart rate setting by
pressing the + or – button beside the Enter button
(see EXERCISE INTENSITY on page 25). Then,
press the Enter button.
If heart rate program 12, 13, or 14 is selected,
the letters “PLS” and the maximum target heart
rate setting for the program will begin to flash in
the right display. If desired, change the maximum
target heart rate setting by pressing the + or – but
-
ton beside the Enter button (see EXERCISE IN-
TENSITY on page 25). Then, press the Enter but-
ton. Note: If the maximum target heart rate setting
is changed, the intensity level of the entire pro-
gram will change.
4
3
2
1
CAUTION: If you have heart prob-
lems, or if you are over 60 years of age and
have been inactive, do not use the heart rate
programs. If you are taking medication regu-
l
arly, consult your physician to find whether
the medication will affect your exercise heart
rate.
19
Hold the handgrip pulse sensor.
I
t is not necessary to hold the handgrip pulse sen-
sor continuously during a pulse program; how-
e
ver, you must hold the handgrip pulse sensor fre-
quently.
Each time you hold the handgrip pulse
sensor, keep your hands on the metal con-
tacts for at least 15 seconds. Note: When you
are not holding the handgrip pulse sensor, the let-
ters “PLS” will appear in the display instead of
your heart rate.
Press the Start button or the Speed increase
button to start the program.
A moment after the button is pressed, the tread-
mill will automatically adjust to the first speed and
incline settings of the program. Hold the handrails
and begin walking.
Heart rate program 11 is divided into several
one-minute segments. The same target heart rate
setting is programmed for all segments. (For a
shorter workout, simply stop the program before it
ends.)
Heart rate programs 12, 13, and 14 are
divided into either 20 or 30 one-minute segments.
One target heart rate setting is programmed for
each segment. Note: The same target heart rate
setting may be programmed for two or more con-
secutive segments.
If heart rate program
12, 13, or 14 is se-
lected, the target heart
rate setting for the first
segment will be shown
in the flashing Current
Segment column of
the matrix. The target
heart rate settings for
the next several segments will be shown in the
columns to the right. When only three seconds re-
main in the first segment of the program, both the
Current Segment column and the column to the
right will flash and a series of tones will sound.
When the first segment ends,
all target heart rate
settings will move one column to the left.
The tar-
get heart rate setting for the second segment will
then be shown in the flashing Current Segment
column.
During all heart rate programs, the console will
regularly compare your heart rate to the target
h
eart rate setting for the current segment. If your
heart rate is too far below or above the target
h
eart rate setting, the speed of the walking belt
will automatically increase or decrease to bring
your heart rate closer to the target heart rate set-
ting.
If the speed or incline setting is too high or too low
at any time during the program, you can adjust the
setting with the Speed or Incline buttons. However,
when the console compares your heart rate to the
target heart rate setting, the speed of the treadmill
may automatically change to bring your heart rate
closer to the target heart rate setting.
If your pulse is not detected during the program,
the letters “PLS” will flash in the right display and
the speed of the treadmill may automatically de-
crease.
To stop the program at any time, press the Stop
button. To restart the program, press the Start but-
ton or the Speed increase button. The walking belt
will begin to move at 1 mph. When the console
compares your heart rate to the target heart rate
setting, the speed and/or incline of the treadmill
may automatically change to bring your heart rate
closer to the target heart rate setting.
Follow your progress with the displays.
See step 5 on pages 12 and 13.
Turn on the fan if desired.
See step 7 on page 13.
When you are finished exercising, remove the
key from the console.
See step 7 on page 15.
9
8
7
6
5
Current Segment
Column
H
OW TO OPERATE THE PERSONAL TELEVISION
IMPORTANT: Before operating the television, you
must connect a 75 ohm CATV cable to the 75 ohm
terminal on the treadmill. See page 9 for instruc-
t
ions.
Follow the steps below to operate the television.
Insert the key into the console.
See HOW TO TURN ON THE POWER on page
12.
Press the Power button to turn on the
television.
When the key is inserted, the television will auto-
matically turn on. If you have turned off the televi-
sion, turn it on by pressing the Power button.
Press the Channel buttons to select the
desired cable channel.
Note: Complete this step only if you are using
analog cable. Otherwise, change channels
through an external source such as your cable
box or your VCR.
When the television is turned on, the screen will
show the last cable channel that was selected. To
select a different channel, press the Channel but-
tons. The selected cable channel number will ap-
pear on the screen for a few seconds. Note: The
television is equipped with a channel memorizing
function that allows you to go directly from the cur-
rent channel to the next channel saved in mem-
ory. Before channels can be selected in this way,
they must be saved in the television’s memory.
See HOW TO USE THE INFORMATION MODE
at the right.
Press the Volume buttons to adjust the volume.
When either Volume button is pressed, the vol-
ume level indicator will appear on the screen for a
few seconds. To temporarily mute the sound,
press the Mute button. Press the Mute button
again to listen to the television. Note: To use ear-
phones or headphones (not included), plug them
into the headphone jack on the console.
When you are finished using the television,
press the Power button.
Press the Power button to turn off the television.
Note: Removing the key from the console will also
turn off the television.
H
OW TO USE THE INFORMATION MODE
The console features an information mode that allows
you to view treadmill usage information, select a sys-
t
em of measurement for the console, and turn on and
t
urn off the demo mode. The information mode also al-
lows you to adjust the settings of the television and to
save channels into the television’s memory.
Follow the steps below to use the information mode.
Hold down the Stop button while inserting the
key into the console.
When the information mode is selected, the left
display will show the total number of hours that the
treadmill has been used. The right display will
show the total number of miles or kilometers that
the walking belt has moved.
In addition, the right display will show the letter “E”
for English miles or the letter “M” for metric kilome-
ters. Press the Speed increase button to change
the unit of measurement if desired.
IMPORTANT: If the letter “d” appears in the right
display, the “demo” mode is selected. This mode
is intended to be used only when a treadmill is
displayed in a store. When the demo mode is se-
lected, the power cord can be plugged in, the key
can be removed from the console, and the dis-
plays and indicators on the console will automati-
cally light in a preset sequence. The buttons on
the console will not function. If a “d” appears in
the right display when the information mode is
selected, press the Speed decrease button.
Press the Power button and adjust the
brightness, contrast, color, sharpness, and/or
hue of the television.
When the Power button is pressed, the brightness
level indicator will appear on the television screen.
Press the Volume buttons to adjust the brightness
setting if desired.
Next, press the Channel buttons until the contrast,
color, sharpness, or hue level indicator appears.
Adjust the settings, if desired, by pressing the
Volume buttons.
2
1
5
4
3
2
1
20
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
/