Lenovo LXH-GJ17L3 User manual

Contents

CERTIFICATIONS -------------------------------------------------------------------- 2

NOTICE ---------------------------------------------------------------------------------- 2

PRECAUTIONS ---------------------------------------------------------------- 3

SPECIAL NOTES ON LCD MONITORS --------------------------------- 4

BEFORE YOU OPERATE THE MONITOR ------------------------------------- 4

FEATURES ---------------------------------------------------------------------- 4

PACKING LIST -----------------------------------------------------------------

4

INSTALLATION INSTRUCTIONS------------------------------------------

5

CONTROLS AND CONNECTORS ----------------------------------------

6

ADJUSTING THE VIEWING ANGLE -------------------------------------

7

OPERATING INSTRUCTIONS ----------------------------------------------------- 8

GENERAL INSTRUCTIONS ------------------------------------------------

8

HOW TO USE OSD -----------------------------------------------------------

10

ADJUSTING THE PICTURE --------------------------------------------

10-11

GREEN MONITOR------------------------------------------------------------

12

PLUG AND PLAY -------------------------------------------------------------

12

TECHNICAL SUPPORT(FAQ) ------------------------------------------------- 13-14

ERROR MESSAGE & POSSIBLE SOLUTION ----------------------

15

APPENDIX A SPECIFICATIONS ----------------------------------------- 16

APPENDIX B FACTORY PRESET TIMING TABLE -----------------

17

APPENDIX C CONNECTOR PIN ASSIGNMENT --------------------

18

Notice:

Please read the following words before assembling and using this monitor.

Any reference to an Lenovo product, program or service is not intended to

state or imply that only Lenovo ’s product, program, or service may be used.

Any functionally equivalent product, program, or service that does not infringe

any of Lenovo’s intellectual property rights or other legally protectable rights

may be used instead of the Lenovo product, program, or service. Evaluation

and verification of operation in conjunction with other products, programs, or

services, except those expressly designated by Lenovo, are the user’s

responsibility.

Lenovo may have patents or pending patent applications covering subject

matter in this document. The furnishing of this document does not give you

any license to these patents.

Information in this document is subject to change without notice.

Without the permission of Lenovo (Beijing) Limited, no part of this manual may

be reproduced or distributed in any form or by any means.

lenovo

®

is a lenovo (Beijing) Limited registered trademark.

1

CE certificate

This shipped version of this device complies with the

requirements of the EEC directive 89/336/EEC

“Electromagnetic compatibility” and 73/23/EEC “Low

voltage directive”.

FCC Class B Radio Frequency Interference Statement

WARNING: (FOR FCC CERTIFIED MODELS)

NOTE: This equipment has been tested and found to comply with the limits for

a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits

are designed to provide reasonable protection against harmful interference in

a residential installation. This equipment generates, uses and can radiate

radio frequency energy, and if not installed and used in accordance with the

instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular

installation. If this equipment does cause harmful interference to radio or

television reception, which can be determined by turning the equipment off

and on, the user is encouraged to try to correct the interference by one or

more of the following measures:

1. Reorient or relocate the receiving antenna.

2. Increase the separation between the equipment and receiver.

3. Connect the equipment into an outlet on a circuit different from that to

which the receiver is connected.

4. Consult the dealer or an experienced radio/TV technician for help.

NOTICE:

1. The changes or modifications not expressly approved by the party

responsible for compliance could void the user's authority to operate the

equipment.

2. Shielded interface cables and AC power cord, if any, must be used in

order to comply with the emission limits.

1. The manufacturer is not responsible for any radio or TV interference

caused by unauthorized modification to this equipment. It is the

responsibilities of the user to correct such interference.

WARNING:

To prevent fire or shock hazard, do not expose the monitor to rain or moisture.

Dangerously high voltages are present inside the monitor. Do not open the

cabinet. Refer servicing to qualified personnel only.

2

PRECAUTIONS

z Do not use the monitor near water, e.g. near a bathtub, washbowl, kitchen

sink, laundry tub, swimming pool or in a wet basement.

z Do not place the monitor on an unstable cart, stand, or table. If the monitor

falls, it can injure a person and cause serious damage to the appliance.

Use only a cart or stand recommended by the manufacturer or sold with

the monitor. If you mount the monitor on a wall or shelf, use a mounting kit

approved by the manufacturer and follow the kit instructions.

z Slots and openings in the back and bottom of the cabinet are provided for

ventilation. To ensure reliable operation of the monitor and to protect it

from overheating, be sure these openings are not blocked or covered. Do

not place the monitor on a bed, sofa, rug, or similar surface. Do not place

the monitor near or over a radiator or heat register. Do not place the

monitor in a bookcase or cabinet unless proper ventilation is provided.

z The monitor should be operated only from the type of power source

indicated on the label. If you are not sure of the type of power supplied to

your home, consult your dealer or local power company.

z Cut off the power source during a lightning storm or when it will not be

used for long periods of time. This will protect the monitor from damage

due to power surges.

z Do not overload power strips and extension cords. Overloading can result

in fire or electric shock.

z Never push any object into the slot on the monitor cabinet. It could short

circuit parts causing a fire or electric shock. Never spill liquids on the

monitor.

z Do not attempt to service the monitor yourself, opening or removing covers

can expose you to dangerous voltages and other hazards. Please refer all

servicing to qualified service personnel.

3

SPECIAL NOTES ON LCD MONITORS

The following symptoms are normal with LCD monitor and do not indicate a

problem.

NOTES

• You may find slightly uneven brightness on the screen depending on the

desktop pattern you use.

• The LCD screen has effective pixels of 99.99% or more. It may include

blemishes of 0.01% or less such as a missing pixel or a pixel lit all of the

time.

• Due to the nature of the LCD screen, an afterimage of the previous screen

may remain after switching the image, when the same image is displayed

for hours. In this case, the screen is recovered slowly by changing the

image or turning off the Power for hours.

BEFORE YOU OPERATE THE MONITOR

FEATURES

• 43.2cm(17”) TFT Color LCD Monitor

• Optimal Resolutions is 1280 X 1024@60Hz

• Low Power Consume & Power Saving Design

• Ergonomic Design

• Space Saving, Compact Case Design

CHECKING THE CONTENTS OF THE PACKAGE

The product package should include the following items:

1. LCD Monitor

2. Monitor’s Base

3. Owner's Manual

4. Adapter

5. Power cord

4

INSTALLATION INSTRUCTIONS

SWIVEL BASE

Install Remove

Figure 1 Installing and Removing the Swivel Base

1. During installation, place the display base the right-way up on a flat surface.

Place upper part of the display slowly on to the base and wait for the click

signifying that it is completely in place. Securely fasten the screw with

hands or tools then secure the screws on the bottom with a screwdriver.

2. When removing the rotating base, please place the monitor upside down

taking care not to damage the LCD surface. Manually unscrew the screws

then remove the display’s lower base.

Power Source:

1. Adapter use 12V DC, 4.16A.

2. Power cord user the power supply(90V-264V AC Voltage)

5

CONTROLS AND CONNECTORS

Adapter

Connecting the adapter: Connect one end of the adapter to back of the

monitor and connect the other end to the power cord.

Power cord

Connecting the power cord: Connect one end of the power cord to the AC

adapter and connect the other end to the power supply (90V-264V AC

Voltage).

SIGNAL CABLE

Connecting the Signal Cable: the LCD monitor comes with a built-in video

cable. Plug the signal cable′s 15-pin connector into the computer's video port

and tighten the two screws on the cable connector.

1

2

Figure 2 Connecting Cables

1. AC Adapter & Power cord 2. Signal Cable

6

ADJUSTING THE VIEWING ANGLE

• For optimal viewing it is recommended to look at the full face of the

monitor, then adjust the monitor’s angle to your own preference.

• Hold the stand so you do not topple the monitor when you change the

monitor’s angle.

• You are able to adjust the monitor’s angle from -5° to 20°.

-5

°

20

°

Figure 3

NOTES

• Do not touch the LCD screen when you change the angle. It may cause

damage or break the LCD screen.

• Careful attention is required not to catch your fingers or hands when you

change the angle.

7

OPERATING INSTRUCTIONS

GENERAL INSTRUCTIONS

Press the power switch to turn the monitor on or off. The other control knobs

are located at front panel of the monitor (See Figure 4). By changing these

settings, the picture can be adjusted to your personal preferences.

Figure 4 External Control Button

EXTERNAL CONTROLS

1.

Auto Config / Exit

2.

▲/ Brightness

3. ▼/ Contrast

4.

MENU / ENTER

5. Power / Power indicator

8

FRONT PANEL CONTROL

• Power / Power indicator :

Press this knob to switch ON/OFF of monitor’s power. and display the

monitor’s state.

Blue

— Power On mode.

Orange — Power Off mode.

• MENU/ENTER / :

Activate OSD menu or function adjusts confirmation.

• Contrast / ▼:

Adjust contrast or function adjustment.

• Brightness / ▲:

Adjust brightness or function adjustment.

• Auto Config Key / EXIT/ :

1. When OSD menu is in active status, this knob will act as EXIT-KEY

(EXIT OSD menu).

2. When OSD menu is in off status, press this knob over 1 seconds to be

in Auto Adjustment function.

The Auto Adjustment function is used to set the HPos, VPos, Clock and

Focus automatically.

NOTES

• Do not install the monitor in a location near heat sources such as radiators

or air ducts, or in a place subject to direct sunlight, or excessive dust or

mechanical vibration or shock.

• Save the original shipping carton and packing materials, as they will come

in handy if you ever have to ship your monitor.

• For maximum protection, repackage your monitor as it was originally

packed at the factory.

• To keep the LCD clean, periodically clean it with a soft cloth. Any kind of

liquids will damage the LCD.

• To keep the monitor looking new, periodically clean it with a soft cloth.

Stubborn stains may be removed with a cloth lightly dampened with a mild

detergent solution. Never use strong solvents such as thinner, benzene, or

abrasive cleaners, since these will damage the cabinet. As a safety

precaution, always unplug the monitor before cleaning it.

9

HOW TO USE OSD

The main menu will be displayed as follows (see figure 5). If OSD window is in

Chinese when power on, press ▲ or ▼

to choose the next window. Choose

the English, then press MENU Key . for confirming. OSD window will display

in English.

1. Press the MENU-Key . to show the OSD window. See figure 5.

2. Press ▲ or ▼ to select the adjusted item, then press the MENU-key

.

3. Press ▲ or ▼ to change the settings of selected item. Press MENU-key

.

when desired setting is done.

4. If you want to adjust any other items, repeat steps 2-4.

5. To exit and save the setting, press ▲ or ▼ to the exit item and press

MENU-key

, or leave the monitor alone for 10 seconds.

6. When the OSD window is active, it shows the input signal timing.

Figure 5 English OSD Message

ADJUSTING THE PICTURE

The description for function control LEDS

1. BRIGHTNESS & CONTRAST

1.1 BRIGHTNESS

Adjust the picture brightness.

1.2 CONTRAST

Adjust the picture contrast.

2. ADJUST POSITION

2.1 HORIZONTAL POSITION

Adjust the horizontal position of the picture.

2.2 VERTICAL POSITION

Adjust the vertical position of the picture.

3. VIDEO NOISE

10

3.1 FOCUS

Adjust the picture Focus.

3.2 CLOCK

Adjust the picture Clock.

4. LANGUAGE

Multi-Language selection.

5. OSD TIMER

Choose OSD window display time.

6. COLOR TEMPERATURE

6.1 7800K/6500K (COLOR TEMPERATURE)

The color temperature for 7800K is x=0.296, y=0.311

and 6500K is x=0.313, y=0.329. It presents two

different color sets on the screen. You can select

7800K or 6500K by pressing MENU Key.

6.2 USER MODE (Red / Green/ Blue)

If the 7800K normal white or 6500K warmer white do

not satisfy your desire, properly adjust R .G. B GAIN

controls to obtain your optimum whiteness level.

7. OSD POSITION

7.1 HORIZINTAL OSD

Adjust the horizontal position of the OSD Menu.

7.2 VERTICAL OSD

Adjust the vertical position of the OSD Menu.

8. EXIT OSD

Close OSD window.

9. RESET

Press RESET to restore the monitor to factory settings.

11

Green monitor

• The monitor has a power saving function that conforms to the VESA

standard. When the computer input no signal, the monitor will enter the

shuts off mode.

The power-saving mode can be indicated by the light-emitting diode (LED)

on the front panel:

Signal Power

Mode

Cable Picture Indicator Consumption

On Attached Active Blue ≤ 42 W

Off Attached None Orange ≤ 2 W

Off No attached None Orange ≤ 2 W

PLUG AND PLAY

Plug & Play DDC2B Feature

This monitor is equipped with VESA DDC2B capabilities according to the

VESA DDC STANDARD. It allows the monitor to inform the host system of its

identity and, depending on the level of DDC used, communicate additional

information about its display capabilities.

The DDC2B is a bidirectional data channel based on the I²C protocol. The

host can request EDID information over the DDC2B channel.

12

TECHNICAL SUPPORT (FAQ)

Problem & Question Possible Solution

Power LED is not on *Check if the Power Switch is in the ON

position

*Power Cord should be connected

*Check the Power socket.

*Replace new Power Cord.

No picture, the LED indicator is

light up

*The Signal Cable should be completely

connected to the computer.

*If it is orange, then the monitor and the

computer are in dormancy mode. You

need press your keyboard or move the

mouse to reactivate the system.

*If it is blue, please adjust the

brightness and contrast by OSD menu.

*Check that the computer is switched on.

*Check that the signal’s pin are bent or

broke.

Picture is gray *adjust the brightness and contrast

controls.

Picture bounces or a wave

pattern is present in the picture

*Move electrical devices that may cause

electrical interference.

Picture is fuzzy *17” LCD monitor’s true (physical)

resolution is 1280 x 1024. Under the

resolution, it will get the best display.

Missing one of the primary

colors (RED, GREEN, or

BLUE)

*Inspect the monitor’s video cable and

make sure that none of the pins are

bent or broke (the pin’s number

reference to figure 6)

13

Screen image is not centered or

sized properly.

*Adjust pixel frequency (CLOCK) and

FOCUS or press hot-key (AUTO).

Picture has color defects *Adjust RGB color or select color

temperature

(white does not look white)

Poor brightness or contrast *When the brightness of the screen

lowers after being used for a certain

period and the function of the display

is affected, send it to our authorized

service center for repair.

Horizontal or vertical disturbancies

on the screen

*Use Win 95/98/2000/ME shutdown

mode Adjust CLOCK and FOCUS or

perform hot- key (AUTO-key).

CLOCK (pixel frequency) controls the number of pixels scanned by one

horizontal sweep. If the frequency is not correct, the screen shows vertical

stripes and the picture has not correct width.

FOCUS adjust the phase of the pixel clock signal. With a wrong phase

adjustment the picture has horizontal disturbances in light picture.

For FOCUS and CLOCK adjustment use Win 95/98/2000/ME shutdown mode

pattern.

14

ERROR MESSAGE & POSSIBLE SOLUTION

NO SIGNAL INPUT

1. The computer is switched off.

2. The computer is dormancy.

CABLE NOT CONNECTED :

1. Check that the signal-cable is properly connected, If the connector is

loose, tighten the connector’s screws.

2. Check the signal-cable’s connection pins for damage.

INPUT THE RESOLUTION OUT OF THE RANGE:

Your computer has been set to unsuitable display mode, Set the computer to

display mode given in the following table.

15

APPENDIX A

SPECIFICATIONS

Type TFT Color LCD

Size 43.2cm(17")

LCD Panel

Pixel pitch 0.264mm( H ) x 0.264mm( V )

Video R,G,B Analog Interface

Separate Sync. H/V TTL

H-Frequency 30kHz - 80kHz

Input

V-Frequency 50Hz-75Hz

Display Colors 16.2M Colors

Dot Clock 135MHz

Max. Resolution 1280 x 1024

Plug & Play VESA DDC2B

TM

Input Connector D-Sub 15pin

Input Video Signal Analog:0.7Vp-p(standard),

75 OHM, Positive

Maximum Screen Size Horizontal : 337.92mm

Vertical : 270.34mm

Power Source 12V DC, 3.5A

Environmental

Considerations

Operating Temp.:

0°C to +40°C (32°F to 104°F)

Storage Temp.:

-20°C to 60°C (-4°F to 140°F)

Operating Humidity :

10% to 85%

Weight (N. W.) 4.5kg

Power Consumption 42 Watts

Regulatory Compliance CCC,TCO’95

16

APPENDIX B

FACTORY PRESET TIMING TABLE

STANDARD

RESOLUTION

HORIZONTAL

FREQUENCY

VERTICAL

FREQUENCY

Dos-modo

720 × 400 31.47kHz 70Hz

640 × 480 31.47kHz 60Hz

640 × 480 37.861kHz 72Hz

VGA

640 × 480 37.50kHz 75Hz

800 × 600 37.879kHz 60Hz

800 × 600 48.077kHz 72Hz

SVGA

800 × 600 46.875kHz 75Hz

1024 × 768 48.363kHz 60Hz

1024 × 768 56.476kHz 70Hz

XGA

1024 × 768 60.02kHz 75Hz

1280 × 1024 64.000kHz 60Hz

SXGA

1280 × 1024 80.000kHz 75Hz

17

APPENDIX C

CONNECTOR PIN ASSIGNMENT

15

6

10

11 15

Figure 6 15 - Pin Color Display Signal Cable

PIN NO.

DESCRIPTION

PIN NO.

DESCRIPTION

1. Red 9. +5V

2. Green 10. Ground

3. Blue 11. Ground

4. Ground 12. DDC-Serial Data

5. Ground 13. H-Sync

6. R-Ground 14. V-Sync

7. G-Ground 15. DDC-Serial Clock

8. B-Ground

18

Lenovo LXH-GJ17L3 User manual

Lenovo LXH-GJ17L3 User manual

Related papers

Other documents