Pelco pelco hs1500 User manual

Brand: Pelco

Model: pelco hs1500

Category: Security camera accessories

Type: User manual

This manual is also suitable for

hs1500

Pelco hs1500 is a high-security camera enclosure designed for indoor corner mount installation. It is suitable for various applications such as elevators, parking garages, classrooms, detention cells, and other places that require protection from vandalism. Constructed of heavy gauge steel, the enclosure fits flush to the ceiling and has no exposed mounting hardware, making it difficult to open by unauthorized personnel. It features an impact-resistant clear Lexan window and a factory-installed tamper switch for added security.

HS1500 High-Security

Enclosure

INSTALLATION

C493M-G (11/97)

C493M-G (11/97) 3

Contents

Important Safeguards and Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4

Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5

Models . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5

Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5

Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6

Ceiling Mounting (Flush) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6

Mid-wall Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6

HB1500/HB1524 Heater/Blower Kit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9

Recommended Cable Size . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9

Heater/Blower Kit Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10

Tamper Switch installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11

Tamper Switch Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11

Exploded Assembly Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12

Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13

List of Illustrations

1 HS1500H Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6

2 Heather/Blower Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10

3 Heater/Blower Wiring Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10

4 Tamper Switch Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11

5 HS1500 Enclosure Exploded Assembly Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12

6 HS1500 Enclosure Dimension Drawing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13

List of Tables

A HS1500 Enclosure Exploded Assembly Parts Lists . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12

4 C493M-G (11/97)

Important Safeguards and Warnings

Prior to installation and use of this product, the following WARNINGS should be observed.

1. Installation and servicing should only be done by qualiﬁed service personnel and conform to all local codes.

2. Unless the unit is speciﬁcally marked as a NEMA Type 3, 3R, 3S, 4, 4X, 6, or 6P enclosure, it is designed for indoor use only and it must not

be installed where exposed to rain and moisture.

3. Only use replacement parts recommended by Pelco.

4. After replacement/repair of this unit’s electrical components, conduct a resistance measurement between line and exposed parts to verify

the exposed parts have not been connected to line circuitry.

5. The installation method and materials should be capable of supporting four times the weight of the enclosure, pan/tilt, camera and lens

combination.

6. The camera and lens combination shall not exceed 20 lbs (9.09 kg).

The product and/or manual may bear the following marks:

This symbol indicates that dangerous voltage constituting a risk of electric shock is

present within this unit.

This symbol indicates that there are important operating and maintenance instructions

in the literature accompanying this unit.

CAUTION:

To reduce the risk of electrical shock, do not remove cover. No user-

servicable parts inside. Refer servicing to qualiﬁed service personnel.

Please thoroughly familiarize yourself with the information in this manual prior to installation and operation.

CAUTION:

RISK OF ELECTRIC SHOCK.

DO NOT OPEN.

C493M-G (11/97) 5

Description

The HS1500 is a high security camera enclosure of medium size designed for indoor “corner mount” installation for such applications as

elevators, parking garages, classrooms, detention cells, etc., requiring maximum protection from vandalism in an unobtrusive package. Designed

to ﬁt ﬂush to the ceiling in a corner, an optional hood (HS1500H) allows the HS1500 to be mounted lower on the wall and still retain the

enclosure’s integrity. An impact-resistant clear Lexan window is supplied.

Constructed of heavy gauge steel, the HS1500 will accept most small CCD cameras with ﬁxed focal length lenses ranging in size from 4 mm to

75 mm. There is no exposed mounting hardware securing the HS1500 to its mounting surface. Opening the enclosure can only be accomplished

with a specially designed tool, eliminating the possibility of the enclosure being opened by unauthorized personnel. In addition, a factory-

installed tamper switch is mounted on the secured access cover.

MODELS

HS1500 High security corner mount enclosure designed to ﬁt ﬂush with the ceiling. For use in applications such as elevators,

parking garages, classrooms, detention cells, etc., requiring maximum protection from vandalism in an unobtrusive

package.

OPTIONS

HB1500 120 VAC thermostatically controlled heater. Provides 80 watts of heat which activates ON at 40°F; OFF at 60°F.

Also includes fan that provides continuous internal air circulation.

HB1524 Same as HB1500 except 24 VAC thermostatically controlled heater.

HS1500H Hood for mid-wall mounting of HS1500 enclosure.

6 C493M-G (11/97)

Installation

NOTE:

The four (4) fasteners required to secure the HS1500 to a wall (minimum 3/8” diameter recommended) are not supplied.

Before installing the HS1500 to a wall, make certain that the mounting surface is able to support the full weight of the enclosure plus the camera

and lens.

The tilt table and tilt table mounting brackets may be removed to provide adequate clearance for mounting the enclosure.

CEILING MOUNTING (FLUSH)

To mount the enclosure to a wall (tight to the ceiling), follow the steps outlined below.

1. Remove the cover from the mounting bracket. A special socket is provided (ﬁts 1/4" square drive).

2. Using the mounting bracket (see Figure 4) or the template provided, mark and drill holes in the mounting surface.

NOTE:

A plate is provided to prevent access through the top of this enclosure. If needed, it is mounted with the mounting bracket using the

same mounting holes and hardware

3. Attach the enclosure with the required fasteners.

4. Route the required cables through the back and/or top.

5. Mount the camera/lens to the tilt table.

6. Make all appropriate connections (i.e., camera power, video (coax), lens).

7. Position the camera and tighten the 1/4-20 fasteners to secure the tilt table in place.

8. Replace the cover and check that all components clear. Secure the cover with the 1/4-20 “Tampruf” screw provided.

MID-WALL MOUNTING

To mount the HS1500 enclosure mid-wall, use the optional hood, HS1500H, and

perform the following steps (see Figure 1):

1. Determine the position for the hood. Using it as a template, mark and drill

holes in the mounting surface.

2. Attach the hood with the required fasteners (minimum 3/8" diameter

recommended).

3. Continue with steps 1-8 listed above in Ceiling Mounting section.

Figure 1. HS1500H Installation

C493M-G (11/97) 7

(

8 C493M-G (11/97)

(This page intentionally left blank)

C493M-G (11/97) 9

HB1500/HB1524 HEATER/BLOWER KIT

The HB1500/HB1524 heater/blower kits require either 120 VAC or 24 VAC, respectively. The heater provides 80 watts of heat and is

thermostatically controlled to turn on at 40°F (4.44°C) and turn off at 60°F (15.56°C). The three-watt fan is on continously to provide internal air

circulation.

RECOMMENDED CABLE SIZE

The following cable sizes are the minimum recommended for use with the combination of blower/heater/camera.

CAUTION:

When using a single power source for both the camera and accessories, the camera power consumption must be taken into

consideration when determining the wire gauge.

Model Input Voltage Power Consumption Cable Size Cable Distance

HB1500 120 VAC 85 Watts 22 Awg

20 Awg

18 Awg

524 ft (160 m)

834 ft (254 m)

1327 ft (404 m)

2107 ft (642 m)

HB1524 24 VAC 85 Watts 20 Awg

18 Awg

16 Awg

14 Awg

33 ft (10 m)

53 ft (16 m)

84 ft (26 m)

134 ft (41 m)

10 C493M-G (11/97)

HEATER/BLOWER KIT INSTALLATION

To install the HB1500/HB1524 heater/blower kit, perform the following steps:

1. Remove the cover (Figure 5, item 4).

2. Attach the heater pads to each side of the mounting frame, below the tilt table assembly.

3. Attach the PC board/fan assembly to the mounting frame, to the left or right of the tilt table assembly (see Figure 2).

4. The blower is factory wired to the PCB assembly.

5. Close and lock the cover.

Figure 2.

Heather/Blower Installation

Connect the heaters to the PCB assembly as shown in Figure 3.

Figure 3.

Heater/Blower Wiring Diagram

C493M-G (11/97) 11

TAMPER SWITCH INSTALLATION

The HS1500 enclosure comes standard from the factory with a tamper switch installed. Should it become necessary to install a replacement

switch, refer to Figure 4 for the correct position of the bracket/switch and perform the following steps:

1. Remove the front cover.

2. Install the bracket/switch and secure with lockwashers and nuts.

TAMPER SWITCH WIRING

The tamper switch comes with both a “Normally Open” and a “Normally Closed” contact.

For a “Normally Open” circuit, use the “open” and “common” terminals; for a “Normally Closed” circuit, use the “closed” and “common”

terminals.

Figure 4.

Tamper Switch Installation

Maintenance

Maintenance performed at regularly scheduled intervals will help prolong the operational life and appearance of the equipment.

Clean the Lexan window with a mild non-abrasive detergent in water and a soft cloth regularly to help maintain picture clarity. For a heavily

soiled window, use vinyl cleaner.

12 C493M-G (11/97)

Exploded Assembly Diagram

Figure 5.

HS1500 Enclosure Exploded Assembly Diagram

Table A.

HS1500 Enclosure Exploded Assembly Parts Lists

Item No. Qty Description Part Number

Bracket, switch, break-in

Window, 10" x 9" x .50" drilled MR5 clear Lexan

Plate, mounting

Cover, front

Tilt table

Cover, top, corner mount

Bracket, mount, tilt table, left

Bracket, mount, tilt table, right

Switch, tamper

HS10004313COMP

HS150010009

HS15004001COMP

HS15004003COMP

HS15004008COMP

HS15004023COMP

HS20004115COMP

HS20004215COMP

SWI1DM401

Screw, 1/4-20 x 1/2", round, Tampruf #10, SS

Screw, 1/4-20 x 3/4", round, Tampruf #10, SS

Tape, two-sided, acrylic x inch

Bolt, 1/4-20 x 5/8" hex head C/S, SS

Nut, hex, 1/4-20, SS

Washer, split lock, 1/4" SS

Washer, ﬂat 3/16" special, SS

Washer, ﬂat 15/16", SS

Nut, lock 1-4/20 Nylon insert, SS

Socket, Tampruf #10, 1/4" drive (not shown)

ZH1/4-20X.50SRT

ZH1/4-20X.75SRT

ZHTAPE1.00X.025

ZH1/420X.625CH

ZH1/4-20NUTCH

ZH1/4LWSSL

ZH260X562X65C

ZH932X1.75X130

ZH1/420NUTCHN

ZTSOCKET10

C493M-G (11/97) 13

Speciﬁcations

MECHANICAL

Window 1/2" (12.7 mm) thick impact and abrasion resistant clear Lexan

Camera Mounting Adjustable tilt table

Maximum Camera/Lens Size Accepts camera/lens combinations (including BNC connector) up to: 8.0" L x 4.0" W x 4.0" H

(20.32 cm x 10.16 cm x 10.16 cm)

Enclosure Mounting Four (4) .390" (.99 cm) diameter holes on protected rear surface

Security Tamper-resistant screw. N.O./N.C. switch contact on cover

Tamper Switch Plunger type door switch with “pull to cheat” feature N.O/N.C. contacts clearly marked on body of switch.

DM electrical rating 10A, 125V.

ELECTRICAL

Cable Entry Access through back and top

Tamper Switch Wire Leads 1/4" (0.63 cm) quick connect

N.O./N.C. clearly marked on switch body

10A, maximum switching current

125V, maximum switching voltage

GENERAL

Construction Formed 10 gauge 0.134" (0.34 cm) steel

Finish Polyester powder coat

Dimensions See Figure 6

Environment Indoor; 32° to 120° (0° to 48.89° C)

Unit Weight 15 lbs 4 oz (6.77 kg)

(Design and product speciﬁcations subject to change without notice.)

Figure 6.

HS1500 Enclosure Dimension Drawing

14 C493M-G (11/97)

PRODUCT WARRANTY AND RETURN INFORMATION

WARRANTY

Pelco will repair or replace, without charge, any merchandise proved defective in material or

workmanship

for a period of one year

after the date of shipment.

Exceptions to this warranty are as noted below:

• Five years on FT/FR8000 Series ﬁber optic products.

• Three years on Genex

Series products (multiplexers, server, and keyboard).

• Three years on Camclosure

and ﬁxed camera models, except the CC3701H-2,

CC3701H-2X, CC3751H-2, CC3651H-2X, MC3651H-2, and MC3651H-2X camera models,

which have a ﬁve-year warranty.

• Two years on standard motorized or ﬁxed focal length lenses.

• Two years on Legacy

, CM6700/CM6800/CM9700 Series matrix, and DF5/DF8 Series

ﬁxed dome products.

• Two years on Spectra

, Esprit

, ExSite

™

, and PS20 scanners, including when used in

continuous motion applications.

• Two years on Esprit

and WW5700 Series window wiper (excluding wiper blades).

• Two years (except lamp and color wheel) on Digital Light Processing (DLP

) dis-

plays. The lamp and color wheel will be covered for a period of 90 days. The air

ﬁlter is not covered under warranty.

• Eighteen months on DX Series digital video recorders, NVR300 Series network video

recorders, and Endura

™

Series distributed network-based video products.

• One year (except video heads) on video cassette recorders (VCRs). Video heads will be

covered for a period of six months.

• Six months on all pan and tilts, scanners or preset lenses used in continuous motion

applications (that is, preset scan, tour and auto scan modes).

Pelco will warrant all replacement parts and repairs for 90 days from the date of Pelco

shipment. All goods requiring warranty repair shall be sent freight prepaid to Pelco, Clovis,

California. Repairs made necessary by reason of misuse, alteration, normal wear, or accident

are not covered under this warranty.

Pelco assumes no risk and shall be subject to no liability for damages or loss resulting from

the speciﬁc use or application made of the Products. Pelco’s liability for any claim, whether

based on breach of contract, negligence, infringement of any rights of any party or product

liability, relating to the Products shall not exceed the price paid by the Dealer to Pelco for

such Products. In no event will Pelco be liable for any special, incidental or consequential

damages (including loss of use, loss of proﬁt and claims of third parties) however caused,

whether by the negligence of Pelco or otherwise.

The above warranty provides the Dealer with speciﬁc legal rights. The Dealer may also have

additional rights, which are subject to variation from state to state.

If a warranty repair is required, the Dealer must contact Pelco at (800) 289-9100 or

(559) 292-1981 to obtain a Repair Authorization number (RA), and provide the following

information:

1. Model and serial number

2. Date of shipment, P.O. number, Sales Order number, or Pelco invoice number

3. Details of the defect or problem

If there is a dispute regarding the warranty of a product which does not fall under the

warranty conditions stated above, please include a written explanation with the product

when returned.

Method of return shipment shall be the same or equal to the method by which the item was

received by Pelco.

RETURNS

In order to expedite parts returned to the factory for repair or credit, please call the factory at

(800) 289-9100 or (559) 292-1981 to obtain an authorization number (CA number if returned

for credit, and RA number if returned for repair).

All merchandise returned for credit may be subject to a 20% restocking and refurbishing

charge.

Goods returned for repair or credit should be clearly identiﬁed with the assigned CA or RA

number and freight should be prepaid. Ship to the appropriate address below.

If you are located within the continental U.S., Alaska, Hawaii or Puerto Rico, send goods to:

Service Department

Pelco

3500 Pelco Way

Clovis, CA 93612-5699

If you are located outside the continental U.S., Alaska, Hawaii or Puerto Rico and are

instructed to return goods to the USA, you may do one of the following:

If the goods are to be sent by a COURIER SERVICE, send the goods to:

Pelco

3500 Pelco Way

Clovis, CA 93612-5699 USA

If the goods are to be sent by a FREIGHT FORWARDER, send the goods to:

Pelco c/o Expeditors

473 Eccles Avenue

South San Francisco, CA 94080 USA

Phone: 650-737-1700

Fax: 650-737-0933

This equipment contains electrical or electronic components that must be recycled properly to comply with Directive 2002/96/EC of the European Union

regarding the disposal of waste electrical and electronic equipment (WEEE). Contact your local dealer for procedures for recycling this equipment.

REVISION HISTORY

Manual # Date Comments

C493M 5/90 Original manual.

C493M 1/91 Rev. A. Revised to include HB1524 and HS1500H options and heater/blower kit information.

C493M 5/91 Rev. B. Figure 2, HS1500H Installation added.

C493M 11/93 Rev. C. Exploded assembly diagram and parts list updated.

C493M-D 9/95 Rev. D. Revised to include wiring instructions for tamper switch and metric equivalents for speciﬁcations. Heater/blower wiring diagram updated to include 24 VAC

model.

C493M-E 11/95 Rev. E. Revised to include updated tamper switch/bracket part numbers and exploded view diagram.

C493M-F 1/96 Rev. F. Revised to include updated speciﬁcation description, installation instructions, and part numbers for tamper switch update per ECO 95-397.

C493M-G 11/97 Rev. G. Revised to new format. Updated heater-blower information to indicate blower operated in continuous duty mode.

Endura and ExSite are trademarks of Pelco.

DLP is a registered trademark of Texas Instruments, Inc.