Kenmore Elite 79079443600 User manual

Category
Cookers
Type
User manual
-°°.
E L I T E
®
Gas ar e
Estufa a as
Models, Modelos 790.7942 *, 7944*
*= color number, ntJmero de color
www.sears.com Sears Roebuck and Co., Hoffman Estates, {L 60179 U.S.A. pin 316417324 (0606)
Table of Contents
Freestanding Range Warranty ................................................. 2 , Setting
IMPORTANTSAFETYINSTRUCTIONS.....................................3-5 , Setting
Protection Agreements ............................................................ 6 , Setting
Before UsingYour Range .......................................................... 7 , Setting
Range Features ......................................................................... 8 , Setting
Before Setting Oven Controls .............................................. 9-10 , Setting
Before Setting Surface Controls ............................................ 10 , Setting
Surface Cooking ................................................................. 11-13 , Setting
Setting Warmer Drawer & Controls .................................. 13-15 , Setting
ElectronicOven Control Pad Features ................................... 16 , Setting
Minimum& MaximumControl PadSettings ......................... 16 , Setting
Setting Oven Controls ........................................................ 17-31 , Setting
, Setting the Clock ............................................................... 17
, Changing between 12 or 24 Hour Display ....................... 17
, Silent Control Operation.................................................... 17
, Continuous Bake or 12 Hour Energy Saving Mode .......... 18
, Timer ................................................................................. 18
, Oven Lockout..................................................................... 19
, Changing Temperature Display........................................ 19
Preheat .................................................................. 21
Bake ...................................................................... 22
Cook Time ............................................................. 23
Delay Start ............................................................. 24
Broil & Searing Grill .............................................. 25
Convection Roast ................................................. 26
Cakes and Breads ................................................ 26
Convection Bake ................................................... 27
Convection Convert ............................................... 28
Add 1 Minute Feature ............................................ 28
Slow Cook ............................................................. 29
the Sabbath Feature ........................................ 30-31
,, Setting Warm & Hold ......................................................... 31
Self-Cleaning ....................................................................... 32=34
Adjusting Oven Temperature .................................................. 35
General Care & Cleaning .................................................... 36=40
Before You Call for Service ................................................ 41 =42
Recipes for Slow Cook ............................................................ 43
Sears Service ............................................................ back cover
: _!_ _ .................................8_
Kenmore Elite Appliance Warranty
One Year Limited Warranty
When installed, operated and maintained according to all instructions supplied with the product, if this appliance fails due to
a defect in material or workmanship within one year from the date of purchase, call 1-800-4-MY-HOME ®to arrange for free
repair. If this appliance is used for other than private family purposes, this warranty applies for only 90 days from the date of
purchase.
This warranty covers only defects in material and workmanship. Sears will NOT pay for:
1. Expendable items that can wear out from normal use, including but not limited to filters, belts, light bulbs, and bags.
2. Aservice technician to instruct the user in correct product installation, operation or maintenance.
3. A service technician to clean or maintain this product.
4. Damage to or failure of this product if it is not installed, operated or maintained according to all instructions supplied with
the product.
5. Damage to or failure of this product resulting from accident, abuse, misuse or use for other than its intended purpose.
6. Damage to or failure of this product caused by the use of detergents, cleaners, chemicals or utensils other than those
recommended in all instructions supplied with the product.
7. Damage to or failure of parts or systems resulting from unauthorized modifications made to this product.
FIVE-YEAR LIMITED WARRANTY
For five years from the date of purchase, when this range is installed, operated, and maintained according to all instructions
supplied with this product, Sears will replace the following range parts free of charge if they fail for the reasons below.
Customer must pay labor cost of installation.
Cooktop glass if it fails due to thermal shock.
Cooktop elements if they are defective.
Disclaimer of implied warranties; limitation of remedies
Customer's sole and exclusive remedy under this limited warranty shall be product repair as provided herein, implied
warranties, including warranties of merchantability or fitness for a particular purpose, are limited to one year or the shortest
period allowed by law. Sears shall not be liable for incidental or consequential damages. Some states and provinces do not
allow the exclusion or limitation of incidental or consequential damages, or limitations on the duration of implied warranties of
merchantability or fitness, so these exclusions or limitation may not apply to you.
This warranty applies only while this appliance is used in the United States and Canada.
This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.
Sears, Roebuck and Co., Dept. 817WA, Hoffman Estates, IL 60179
Sears Canada Inc., Toronto, Ontario, Canada MSB 2B8
important Safety instructions
Read all instructions before using this appliance. Save these instructions for future reference.
This manual contains important safety symbols and instructions. Please payattention to these symbols and follow allinstructions given.
This Symb01 wil! help alert you to situations that may caus e se[i0us b0dily harml death or pr0perty damagel
This symbol will help alert you to Situations that may Cause bodily injury Orproperty damagel
If the information in this manual is not
followed exactly, a fire or explosion may result
causing property damage, personal injury or death.
FOR YOUR SAFETY:
-- Do not store or use gasoline or other flammable
vapors and liquids in the vicinity of this or any
otherappliance.
-- WHAT TO DO IF YOU SMELL GAS:
* Do not try to light any appliance.
* Do not touch any electrical switch; do not use
any phone in your building.
, immediately call your gas supplier from a
neighbor's phone. Follow the gas supplier's
instructions.
* if you cannot reach your gas supplier, call the
fire department.
-- installation and service must be performed by a
qualified installer, servicer or the gas supplier.
o All ranges can tip.
Injury to persons could result.
, Install anti-tip device packed with range.
See Installation Instructions.
_To reduce the risk of
tipping, the rangemust be secured by
properly installed anti-tip bracket provided
with the range. To check if the bracket is
installed properly, visually check that rear
leveling leg is inserted into and fully
secured by the anti-tip bracket by
removing lower panel or storage drawer.
For models with a warmer drawer, grasp
the top rear edge of the range and
carefully attempt to tilt it forward. Refer to
the installation instructions for proper anti-
tip bracket installation.
Remove all tape and packaging before using the range.
Destroy the carton and plastic bags after unpacking the range.
Never allow children to play with packaging material.
Proper Installation--Be sure your appliance is properly
installed and grounded by a qualified technician in
accordance with the National Fuel Gas Code ANSI Z223.-
latest edition, or in Canada CAN/CGA B149.1, and CAN/CGA
B149.2, and the the National Electrical Code ANSI/NFPA
No.70-1atest edition, or in Canada CSA Standard C22.1,
Canadian Electrical Code, Part 1, and local code
requirements. Install only per installation instructions
provided in the literature package for this range.
Ask your Sears dealer to recommend a qualified technician
and an authorized Sears repair service. Know how to
disconnect the power to the range at the circuit breaker or
fuse box in case of an emergency.
User servicing--Do not repair or replace any part of the
appliance unless specifically recommended in the manuals.
All other servicing should be done only by a qualified
technician, This may reduce the risk of personal injury and
damage to the range.
Never modify or alter the construction of a range by
removing leveling legs, panels, wire covers, anti-tip
brackets/screws, or any other part of the product.
Air curtain or other overhead range hoods, which operate
by blowing a downward airflow on to a range, shall not be
used in conjunction with gas ranges other than when the
hood and range have been designed, tested and listed by an
independent test laboratory for use in combination with
each other.
Stepping, leaning or sitting on the doors or
drawers of this range can result in serious injuries and also
cause damage to the range. Do not allow children to climb or
play around the range. The weight of a child on an open door
may cause the range to tip, resulting in serious burns or other
injury.
NEVER use this appliance as a space
heater to heat or warm the room. Doing so may result in
carbon monoxide poisoning.
NEVER cover any slots, holes or passages in
the oven bottom or cover an entire rack with materials such as
aluminum foil. Doing so blocks air flow through the oven and
may cause carbon monoxide poisoning. Aluminum foil linings
may trap heat, causing a fire hazard.
Do not use the oven or warmer drawer (if
equipped) for storage.
Storage in or on Appliance--Flammable materials should
not be stored in an oven, warmer drawer, near surface
burners or in the storage drawer. This includes paper, plastic
and cloth items, such as cookbooks, plasticware and towels,
as well as flammable liquids. Do not store explosives, such as
aerosol cans, on or near the range.
Do not store items of interest to children in
the cabinets above a range or on the backguard of a range.
Children climbing on the range to reach items could be
seriously injured.
important Safety instructions
Do Not Leave Children Alone--Children should not be left
alone or unattended in the area where appliance is in use.
They should never be allowed to sit or stand on any part of the
appliance.
+DO NOTTOUCH SURFACE BURNERS,AREAS NEARTHESE
BURNERS, OVEN BURNERS OR iNTERIOR SURFACES OF THE
OVEN. Both surface and oven burners may be hot even though
flames are not visible. Areas near surface burners may
become hot enough to cause burns. During and after use, do
not touch, or let clothing or other flammable materials touch
these areas until they have had sufficient time to cool. Among
these areas are the cook top, surfaces facing the cook top, the
oven vent openings and surfaces near these openings, oven
door and window.
Wear Proper Apparel--Loose-fitting or hanging garments
should never be worn while using the appliance. Do not let
clothing or other flammable materials contact hot surfaces.
Do Not Use Water or Flour on Grease Fires--Smother the
fire with a pan lid, or use baking soda, a dry chemical or
foam-type extinguisher.
When heating fat or grease, watch it closely. Fat or grease
may catch fire if allowed to become too hot.
Use Only Dry Potholders--Moist or damp potholders on hot
surfaces may result in burns from steam. Do not let
potholders touch hot heating burners. Do not use a towel or
other bulky cloth instead of a potholder.
Do Not Heat Unopened Food Containers--Buildup of
pressure may cause container to burst and result in injury.
Remove the oven door from any unused range if it is to be
stored or discarded.
IMPORTANT--ELECTRIC IGNITION MODELS ONLY: Do not
attempt to operate the oven during a power failure. If the power
fails, always turn off the oven. If the oven is not turned off and
the power resumes, the oven will begin to operate again. Once
the power resumes, reset the clock and oven function.
+Protective Liners--Do not use aluminum foil to line surface
burner pans, or oven bottom, except as suggested in this
manual. Improper installation of these liners may result in risk
of electric shock, or fire.
+Glazed Cooking Utensils--Only certain types of glass, glass/
ceramic, ceramic, earthenware, or other glazed utensils are
suitable for cooktop service without breaking due to sudden
change in temperatures. Check the manufacturer's
recommendations for cooktop use.
IMPORTANT INSTRUCTIONS FOR USING YOUR OVEN
Use Care When Opening Oven Door or Warmer Drawer--
Stand to the side of the range when opening the door of a hot
oven. Let hot air or steam escape before you remove or
replace food in the oven.
+Keep Oven Vent Ducts Unobstructed. The oven vent is
located below the backguard. Touching the surfaces in this
area when the oven is operating may cause severe burns.
Also, do not place plastic or heat-sensitive items on or near
the oven vent. These items could melt or ignite.
+Placement of Oven Racks. Always place oven racks in
desired location while oven is cool. If rack must be moved
while oven is hot use extreme caution. Use potholders and
grasp the rack with both hands to reposition. Do not let
potholders contact the hot heating elements in the oven.
Remove all utensils from the rack before moving.
Do not use the broiler pan without its insert. The broiler pan
and its insert allow dripping fat to drain and be kept away from
the high heat of the broiler.
Do not cover the broiler insert with aluminum foil. Exposed
fat and grease could ignite.
. Cold temperatures can damage the electronic control. When
using the appliance for the first time, or when the appliance
has not been used for an extended period of time, be certain
the unit has been in temperatures above 32°F (0°C) for at
least 3 hours before turning on the power to the appliance.
IMPORTANT INSTRUCTIONS FOR USING
YOUR COOKTOP
Use Proper Flame Size--Adjust flame size so
it does not extend beyond the edge of the utensil. The use of
undersized utensils will expose a portion of the burner flame to
direct contact and may result in ignition of clothing. Proper
relationship of utensil to flame will also improve efficiency.
+Know which knob controls each surface burner. Place a
pan of food on the burner before turning it on, and turn the
burner off before removing the pan.
,,Always turn knob to the full LITE position when igniting top
burners. Visually check that burner has lit. Then adjust the flame
so it does not extend beyond the edge of the utensil.
,,Utensi! Handles Should Be Turned inward and Not Extend Over
Adjacent Surface Burners--To reduce the risk of burns, ignition
of flammable materials, and spillage due to unintentional contact
with the utensil, the handle of the utensil should be positioned so
that it is turned inward, and does not extend over adjacent surface
burners.
,,Never Leave Surface Burners Unattended at High Heat
Settings--Boilovers cause smoking and greasy spillovers that
may ignite, or a pan that has boiled dry may melt.
IMPORTANT INSTRUCTIONS FOR CLEANING
YOUR RANGE
Clean the range regularly to keep all parts free of grease
that could catch fire. Pay particular attention to the area
underneath each surface element. Do not allow grease to
accumulate. Refer to the range manufacturer's instructions for
cleaning.
Kitchen cleaners and aerosols--Always follow the
manufacturer's recommended directions for use. Be aware
that excess residue from cleaners and aerosols may ignite
causing damage and injury.
SELF CLEANING OVENS
Clean in the self-cleaning cycle only the parts listed in this
Use & Care Guide. Before self cleaning the oven, remove the
broiler pan and any utensils or foods from the oven.
+Do Not Use Oven Cleaners--No commercial oven cleaner or
oven liner protective coating of any kind should be used in or
around any part of the oven.
+Do Not Clean Door Gasket--The door gasket is essential for
a good seal. Care should be taken not to rub, damage or
move the gasket.
important Safety instructions
FOR CERAMIC-GLASS COOK TOP MODELS (some models)
Do Not Cook on Broken Cook Top--If cook top should break, cleaning solutions and spillovers may penetrate the broken cook top
and create a risk of electric shock. Contact a qualified technician immediately.
Clean Cook Top with Caution--if a wet sponge or cloth is used to wipe spills on a hot cooking area, be careful to avoid a steam burn.
Some cleaners can produce noxious fumes if applied to a hot surface.
Grounding type
wall receptacle
Power supply cord
with 3=prong
grounding plug
Do not, under any |
circumstance, cut,
remove, or bypass
the grounding prong.
J
Grounding Instructions
(electric ignition models only)
Avoid fire hazard or electrical shock. Do not use an adapter plug,
an extension cord, or remove grounding prong from electrical power cord.
Failure to follow this warning can cause serious injury, fire or death.
This appliance is equipped with a 3-prong grounding plug for
your protection against shock hazard and should be plugged directly into a
properly grounded receptacle. DO NOT cut or remove the grounding prong from
this plug.
For personal safety, the range must be properly grounded. For maximum safety,
the power cord must be plugged into an electrical outlet that is correctly polarized
and properly grounded.
If a 2-prong wall receptacle is the only available outlet, it is the personal
responsibility of the consumer to have it replaced with a properly grounded 3-
prong wall receptacle installed by a qualified electrician.
See the INSTALLATION INSTRUCTIONS packaged with this range for complete
installation and grounding instructions.
Important Safety Notice
The California Safe Drinking Water and Toxic Enforcement Act requires the Governor of California to publish a list of substances
known to the state to cause cancer, birth defects or other reproductive harm, and requires businesses to warn customers of
potential exposure to such substances.
Conversion to Liquefied Petroleum Gas (or L.P. Gas)
The natural gas range isdesigned to allow for conversion to
Liquefied Petroleum (L.P.) Gas.
If L.P.conversion is needed, contact 1-800-4-MY-HOME® for
assistance. The L.P. Conversion Kit is provided with this range
and is located on the left lower REAR (back side) panel of the
range. Before installing the kit be sure to follow the L.P.
Installation Instructions carefully.
Personal injury or death from electrical
shock may occur if the range is not installed by a
qualified installer or electrician.
Any additions, changes or conversions
required in order for this appliance to satisfactorily meet
the application needs must be made by Sears Service.
PROTECTION AGREEMENTS ACUERDOS DE PROTECCION
In the U.S.A.
Master Protection Agreements
Congratulations on making a smart purchase. Your new
Kenmore C_product isdesigned and manufactured for years
of dependable operation. But like all products, it may require
preventive maintenance or repair from time totime. That's
when having a Master Protection Agreement can save you
money and aggravation.
Purchase a Master Protection Agreement now and protect
yourself from unexpected hassle and expense.
The Master Protection Agreement also helps extend the life
of your new product. Here's what's included in the
Agreement:
5_ Expert service by our 12,000 professional repair
specialists.
5_ Unlimited service and no charge for parts and labor
on all covered repairs.
5_ "No-lemon" guarantee- replacement
of your covered product iffour or more product failures
occur within twelve months.
5_ Product replacement if your covered product can't be
fixed.
5_ Annual Preventive Maintenance Check at your
request- no extra charge.
5_ Fast help by phone - phone support from a Sears
technician on products requiring in-home repair, plus
convenient repair scheduling.
5_ Power surge protection against electrical damage
due to power fluctuations.
5_ Rental reimbursement if repair of your covered
product takes longer than promised.
Once you purchase the Agreement, a simple phone call is
all that it takes for you to schedule service. You can call
anytime day or night, or schedule a service appointment
online.
Sears has over 12,000 professional repair specialists, who
have access to over 4.5 million quality parts and
accessories. That's the kind of professionalism you can
count on to help prolong the life of your new purchase for
years to come. Purchase your Master Protection
Agreement today!
Some limitations and exclusions apply.
For prices and additional information call
1-800-827-6655.
Sears Installation Service
For Sears professional installation of home
appliances, garage door openers, water heaters,
and other major home items, in the U.S.A. call
1-800-4-MY-HOME ®.
En los EE.UU.
Acuerdos maestros de protecci6n
Lo felicitamos por haber hecho una compra inteligente. Su
nuevo producto Kenmore®rue diseSado y fabricado para
ofrecer muchos aSos de servicio confiable. Sin embargo,
como todo producto, el mismo podrta requerir mantenimiento
preventivo o reparaciones ocasionales. Es por eso que el
tenet un Acuerdo maestro de protecci6n podrfa ahorrarle
dinero y molestias.
Adquiera ya un Acuerdo maestro de protecciOn y protejase de
gastos y frustraciones inesperados.
El Acuerdo maestro de protecci6n tambi_n ayuda a extender
la vida de su producto nuevo. El Acuerdo incluye Io siguiente:
5_ Servicio profesional por nuestros 12.000 profesionales
especialistas en reparaci6n.
5_ Servicio ilimitado sin cargos adicionales por piezas
y servicio en todas las reparaciones cubiertas.
5_ Garantia de "no-lim6n" - reemplaza su producto
cubierto si ocurren cuatro o mas desperfectos en los
primeros doce meses.
5_ Reemplazo del producto si el mismo no puede ser
reparado.
5_ Verificaci6n de mantenimiento preventivo anual a
su petici6n y sin cargos adicionales.
5_ Pronta ayuda pot tel_fono - apoyo por tel_fono por un
t_cnico de Sears en los productos que requieran
reparaci6n en casa, ademas de la conveniencia de hacer
una cita para la reparaci6n.
5_ Protecci6n contra picos de energia o da_os
el_ctricos causados pot fluctuaciones de la corriente
el_ctrica.
5_ Reembolso del alquiler si la reparaci6n de su producto
cubierto toma mas del tiempo prometido.
Una vez que adquiera este Acuerdo, una simple Ilamada
telef6nica es todo Io que necesita para hacer una cita de
servicio. Usted puede Ilamar a cualquier hora del dfa o de la
noche para programar una cita de servicio por Internet.
Sears cuenta con ma.sde 12.000 profesionales especialistas
de reparaci6n con acceso a mas de 4,5 millones de piezas y
accesorios de calidad. Esa es la clase de profesionalismo
con la que puede contar para extender la vida t_tilde su nueva
adquisici6n por muchos a_os. iAdquiera su Acuerdo maestro
de protecci6n hoy!
Algunas limitaciones y exclusiones podrian aplicarse.
Para precios e informaci6n adicional, Ilame al
1-800-827-6655.
Servicio de instalaci6n Sears
Para una instalaci6n profesional de Sears en
electrodom_sticos, abridores de puertas de garaje,
calentadores de agua y otros artfculos mayores del hogar,
Ilameal 1-888-SU-HOGAR®.
REV.030509
Before Using Your Range
Assembly of Burner Heads & Burner Caps (for Deep Well Cooktop models only)
Your range isshipped with the Burner Heads and Burner Caps in the correct locations. Packing material islocated between
the Burner Heads and the cooktop.
a. Be sure to follow the installation instructions before
installing and using your new range.
b. Remove all packing tape from cooktop area. Remove all
Burner Caps and Burner Heads.
c. Discard all packing material located under Burner Heads.
d. To replace Burner Heads & Caps, match the letters
located under center of Burner Caps with the letters
located inside Burner Heads (Fig. 1).
e. Match the letters stamped on Burner Skirts with Burner
Heads and Burner Caps (See Fig. 1). Replace the Burner
Heads and Caps on cooktop (See Fig. 2). Carefully align
the Electrodes into slot or hole of each Burner Head (Fig.
3). Note: The Burner Heads should sit flat on Cooktop
Burner Skirts.
f. Unpack Burner Grates and position on the cooktop.
Burner Skirt
Fig. 1
Fig. 2
_ctrodes must
align into slot or hole for each
Fig. 3 Burner Head
Assembly of Burner Heads & Burner Caps (for Ceramic Glass Cooktop models only)
Your range isshipped with the Burner Heads and Burner Caps in the correct locations. Packing material islocated between
the Burner Heads and burner skirts.
a. Be sure to follow the installation instructions before
installing and using your new range.
b. Remove any packing tape from cooktop. Remove all
Burner Caps and Burner Heads, except DO NOT RE-
MOVE Burner Head for Triple Ring Burner (right-front
burner position; See Fig. 4).
c. Discard any packing material located under the Burner
Heads (except Triple Ring Burner position).
d. Replace right rear Burner Head & Cap onto cooktop.
Match the letter for the right-rear burner located inside of
Burner Cap with the letter located inside Burner Head
(only the right-rear position is marked with letter A- See
Fig. 5). Carefully align the Electrode into slot of Simmer
Burner Head (Fig. 7).
e. CAREFULLY (DO NOT FORCE) align the Bridge Burner
Head over the 2 Bridge Burner Electrodes located on left
side of the cooktop. After placing the Bridge Burner Head
on the burner skirt, MAKE SURE that the Bridge Burner
Head lies evenly on burner skirt.
f. Replace Bridge Burner Caps. These include 1 Bridge
Burner Center Cap (rectangular shaped) and the 2 Bridge
Burner End Caps (The Bridge Burner End Caps will fit at
either the front or rear Bridge Burner Head locations).
Make sure that the tabs located under the Bridge Burner
Caps fall into the slots located in the Bridge Burner Head
(See black arrows in Fig. 6) and that the Bridge Burner
Caps lie flat and evenly on top the Bridge Burner Head.
g. Unpack Burner Grates. Position End Burner Grates on
cooktop. Place Center Burner Grate between the end
Burner Grates and check that all the Burner Grate legs lie
flat on the glass cooktop surface.
Fig. 4
Bridge Burner
Head
I
2 Electrode
hole
locations
through
Bridge
Burner
Head
Burner
Head
Burner
Cap
Fig. 5
must align into slot or hole
for Simmer Burner Head
Fig. 7
Fig. 6
Range Features
Your Elite Gas Range Features Include:
1. Electronic Oven Control with Timer.
2. Glass Touch Sensitive Control Panel.
3. Left Front Burner Valve & Knob.
4. Left Rear Burner Valve & Knob or Bridge Burner Valve & Knob
(some models).
5. Center Burner Valve & Knob (some models).
6. Right Rear Burner Valve & Knob.
7. Right Front Burner Valve & Knob.
8. Easy to clean Deep Well Cooktop (some models) or Ceramic
Gas through Glass Cooktop (some models).
9. Dishwasher safe Burner Grates (colors vary).
10. Dishwasher safe Center Burner Grate (colors vary).
11. Warmer Drawer Control & Indicator Light.
12. Self-Clean Oven Door Latch.
13. Automatic Oven Door Light Switch.
14. Dual Oven Interior Lights with Shields.
15. Self-Cleaning Oven interior.
16. Convection Bake Fan & Cover.
17. Adjustable Porcelain Coated Oven Racks (includes Handle &
Half Oven Racks).
18. Large 1 piece Oven Door Handle (styles & colors vary with
model).
19. Full width Oven Door (styles & colors vary with model).
20. Warmer Drawer with Handle & Warmer Drawer Rack.
21. 5,000 BTU Simmer Burner.
22. 9,500 BTU Center Burner (some models).
23. 9,500 BTU Power Burner (some models).
24. 14,200 BTU Power Burner (some models).
25. 17,200 BTU Power Burner (some models).
26. "9,000 BTU Burners (Bridge Burner with all 3 burners combined
is 27,000 BTU) (some models).
27.3,000 to 16,000 BTU Triple Ring Burner
(some models)
28. Broil Pan.
29. Broil Pan Insert.
30. Searing Grill.
31. Roasting Rack.
32. Griddle.
33. Leveling Legs and Anti-tip Bracket
(included).
NOTES: The features of your range
may vary according to model type &
color.
*Bridge Burner featured on Glass
Cooktop models only.
• @I
= iiiiiiii@ "
............. t[i
ii_ .............................
®
j
@
@
Deep Well Cooktop style
*Ceramic Glass Cooktop style
8
Before Setting Oven Controls
OVEN VENT Oven Vent Location
The oven vent islocated below the backguard (See Fig. t). When the oven is on,
warm air is released through this vent. This venting is necessary for proper air
circulation in the oven and good baking results. DO NOT BLOCK THE VENT.
Fig. 1
Fig. 2
Types of Oven Racks
Always use pot holders or oven mitts when adjusting the oven racks.
Wait until the oven has completely cooled if possible. Oven racks may be HOT and
may cause burns.
Removing & Replacing Oven Racks
To remove, pull the rack forward until it stops. Lift up front of rack and slide out.
To replace, fit the rack onto the guides on the oven walls. Tilt the front of the rack
upward and slide the rack back into place.This range has a total of 6 oven rack
postions.
Recommended Rack Positions for Broiling, Baking & Roasting:
Food Rack Position
Broiling hamburgers & steaks 5
Broiling meats, chicken or fish 5, 4 or 3
Cookies, cakes, pies, biscuits 2 or3
& Muffins
Frozen pies, angel food cake, 1 or Roasting Rack
yeast, bread, casseroles, small
cuts of meat or poultry
Turkey, roast or ham 1 or Roasting Rack
Flat Handle Oven Rack Flat Half Oven Rac_
Fig. 3
Your range may be equipped with one or more
of the oven rack types shown; a Porcelain
coated Flat Handle Oven Rack (Fig. 3) or a
Porcelain coated Flat Oven Half Rack (Fig.
4). The Flat Oven Half Rack has a removable
insert that can provide extra space for larger
food items. The right half rack portion may still
be used for other food items like a casserole
dish (See Fig. 4).
Fig. 5
Fig. 4
®g
Fig. 6
To remove the Half Oven Rack insert, squeeze on the left front insert side (See Fig. 5) of the rack and tilt out clockwise. To
reinstall insert rear hooks at back of insert (See 1-Fig. 6) and lay insert down. Make sure both insert front hooks snap into
rack (See 2-Fig. 6).
Do not use cookware that extends beyond the edge of the Oven Flat Half Rack. For best results, allow 2 inches between
the pan placed on the rack and oven side or rear walls.
Before Setting Oven Controls
Baking Layer Cakes with 1 or 2 Oven Racks
For best results when baking cakes using 2 oven racks, place cookware on oven rack positions 2 & 5 (See Fig. 1 and Fig.
2 on page 9). For best results when using a single oven rack, place cookware on oven rack position 4 (See Fig. 2 and Fig.
2 on page page 9).
Air Circulation in the Oven
For best air circulation and baking
results allow 2-4" (5-10 cm) around
the cookwa re for proper ai rcirculation
and be su re pans and cookwa re do not
touch each other, the oven door, sides
or back of the oven cavity. The hot air
must be able to circulate around the
pans and cookware in the oven for
even heat to reach around the food.
Fig. 1 Fig.2
Before Setting Surface Controls
Control Locations of the Gas Surface
Burners
(For models with a Deep Well Cooktop-See Fig. 3)
Ther SIMMER Burner is best used for simmering delicate
sauces, etc. This burner is located at the right rear burner
position on the cooktop.
The STANDARD Burners can be used for most surface
cooking needs. These burners are located at the left front
and center positions on the cooktop.
The POWER Burners are best used for bringing large
quantities of liquid rapidly up to temperature or when
preparing larger quantities of food. These burner are
located at the right front and left rear positions on the
cooktop.
(For models with a Ceramic Cooktop-See Fig. 4)
Ther SIMMER Burner is best used for simmering delicate sauces,
etc. This burner is located at the right rear burner position on the
cooktop.
The POWER Burner is best used for bringing large quantities of
liquid rapidly up to temperature or when preparing larger quantities
of food. This burner is located at the right front position on the
cooktop.
The BRIDGE Burner is best suited when using rectangular or long
shaped cookware. The left rear and left middle positions are
combined. The left front Burner may also be added for a total of 3
burners.
The TRIPLE RING Burner offers a complete range of gas surface
burner settings from simmering to the output of a Power Burner at
one location.
Fig. 3 Fig. 4
0 0 0 0 Power 0 0 Power 0 0 Q 0 Simmer
00 U _0 U Burner O_U Burner _0_ UO_ Burner
Front Rear Center Front Rear
Left Left Center Right Right
Front Rear Burner Front Rear
Burner Burner Burner Burner
POWER BURNER POWER BURNER SIMMER BURNER
RE,,,, E.ONT00 °EAR
@ +BRIDGE +TRIPLE
Left Left Rear & Right Right
Front Bridge Burner Front Rear
Burner Burner Burner
10
Surface Cooking
Operating Gas Surface Burners
Setting Proper Burner Flame Size
Operating Triple Ring Burner
Do not place plastic items such as salt and pepper shakers, spoon holders or plastic wrappings on
top of the range when it is in use. These items could melt or ignite. Potholders, towels or wood spoons could catch fire
if placed too close to a flame.
Operating the Gas Surface Burners:
1. Place cooking utensil on surface burner.
2. Push the knob in and turn counterclockwise out of the OFF position (See Fig. 1).
3. Release the knob and rotate to the LITE position. Note: All four electronic surface ignitors will
spark at the same time. However, only the burner you are turning on will ignite.
4. Visually check that the burner has lit.
5. Push the control knob in and turn counterclockwise to the desired flame size. The control
knobs do not have to be set at a particular setting. Usethe guides and adjust the flame as
needed. DO NOT cook with the surface control knob in the LITE position (The electronic ignitor
will continue to spark if the knob is left in the MTE position).
Fig. 1
Setting Proper Surface Burner Flame Size
The size and type of utensil used and the amount of food being cooked will
influence the setting needed for cooking.
High Flame Start most foods; bring water to a boil; pan broiling.
Medium Flame Maintain a slow boil; thicken sauces, gravies; steaming.
Low Flame Keep foods cooking; poach; stewing.
Always select cookware that is suitable for the amount and type of food being prepared.
Select a burner and flame size appropriate to the pan. Never allow flames to extend beyond
the outer edge of the pan.
iiMiiiiiiiiiii¸iiiii i!i!i i!ii! !ii!i !ii!ii!i!iiiiiii!i i !ii!i!i!i!iii!Jiiii ; iiif :2:
!i¸¸
ize ,
Improper
flame size
Fig. 2
Triple Ring Burner (some models):
The versatile Triple Ring Burner offers a complete range of gas surface settings from the same burner location. At the
lowest setting, only the inner ring isactive, providing a low flame for any simmering needs. If needed however, two additional
gas rings may be added quickly to provide a "Power Burner" output of 16,000 BTU. When set at the highest, the Triple Ring
may be used to bring a large pan of liquid to boil quickly.
Operating the Triple Ring Burner:
1. Push the right front surface control knob in and turn counterclockwise out of the OFF position (See Fig. 1).
2. Release the knob and rotate to the LITE position (See Fig. 1). Note: Although all electronic surface ignitors will spark at
the same time, only the selected surface Burner will lite.
3. Visually check that the inner ring of the right front Burner has lit.
4. Continue to rotate the gas control knob clockwise past the first LO setting to the arrow marked TRIPLE.
5. Visually check that both the inner and outer ring of the Triple Ring Burner are lit.
6. When both burners are lit, continue to turn the control knob counterclockwise to adjust to the desired flame size for
both burners together. Note: The markings between the 2rid HI and LO settings on the left rear control knob adjust the
flame size for both burners. Use the guide marks between the 2rid HI and LO settings and adjust the flame size as
needed (Refer to Fig. 3).
Off
Inner Ring
Inner Ring flame
LITE adjustment
postion
I F area 1
,Hi Lo
Entire Entire Triple
Burner Burner
LITE flame
position adjustment =l
I [= area |
Triple Hi Lo
_d__
I!
Fig. 3 - Triple Ring Burner Surface Control Knob markings
Fig. 4 Fig. 5
11
Surface Cooking
,, Operating Triple Ring Burner Conrd (some models)
Operating the Bridge Burner (some models)
Operating the Triple Ring Burner at the lowest setting:
1. Push the right front surface control knob in and turn counterclockwise out of the OFF position (See Fig. 1).
2. Release the knob and rotate to the LITE position (See Fig. 1). Note: Although all electronic surface ignitors will spark at
the same time, only the selected surface Burner will lite.
3. Visually check that the inner ring of the right front Burner has lit.
4. Continue to turn the control knob counterclockwise and stop at the first LO position. (Refer to Fig. 3). If a higher setting
is need adjust accordingly.
Setting the Bridge Burner (for Bridge Burner models only):
The Bridge Burner should be used with rectangular shaped cookware. Cookware like the cast- Left
Rear
iron Griddle that is supplied with your range isdesigned specifically for best results with the Burner
Bridge Burner. Left
The Bridge Burner feature may be used to combine the cooking power of 2 or ifneeded 3 gas Burner
surface Burners located along the left-hand side of the glass cooktop.The left rear and left center
Burners are controlled by the left rear surface Control Knob. In addition the left front Burner may Front
be added to the Bridge Burner with the left front gas Control Knob (See Fig. 1). Burner
Operating the Bridge Burner (for Bridge Burner models only): _
1. Push the left rear surface control knob inand turn counterclockwise out of the OFF position
(See Fig. 1).
2. Release the knob and rotate to the LITE position (See Fig. 1 on page 11). Note: All electronic _ _
surface ignitors will spark at the same time. However, only the selected surface Burner will
lite.
3. Visually check that the left rear Burner has lit.
4. Contine to rotate the gas control knob clockwise past the first LO setting to the arrow marked
BRIDGE.
5. Visually check that both the left rear and left center Burners are lit. Fig. 1
6. When both burners are lit, continue to turn the control knob counterclockwise to adjust to the desired flame size for
both burners together. Note: The markings between the 2rid Hi and LO settings on the left rear control knob adjust the
flame size for both burners. Use the guide marks between the 2nd Hi and LO settings and adjust the flame size as
needed (Refer to Fig. 3).
7. Add the left front Burner ifneeded. Once lit, visually adjust the flame size of the left front Burner to match the flame size
of the Bridge Burner.
8. Place cooking utensil centered over the left-hand cooktop surface Burner Grate. DO NOT cook with any of the surface
control knobs in the LITE position (The electronic ignitor will continue to spark ifthe knob is left in the LITE position).
Off
Left Rear Left Rear Bridge Bridge
Burner Burner Burner Burner
LITE flame UTE flame
position [=adjustment 7 position adjustment =
, /area / , F areat
_Hi Lo
Bridge Hi Lo
Fig. 3 - Left Rear Bridge Burner Surface Control Knob markings
Note: Ifonly the left rear surface Burner isneeded, follow the instructionsprovided below.
Operating only the Left rear Gas Surface Burner (for models equipped with Bridge Burner):
1. Place cooking utensil centered over the left-rear surface Burner Grate.
2. Push the left rear surface control knob in and turn counterclockwise out of the OFF position (See Fig. 2).
3. Release the knob and rotate to the LITE position. Note: Although all electronic surface ignitors will spark at the same
time, only the left rear Burner will ignite.
4. Visually check that the left-rear burner has lit. Adjust the flame size by turning the control knob between the first HI
and LO settings (See Fig. 3). DO NOT cook with the surface control knob in the LITE position (The electronic ignitor
will continue to spark ifthe knob isleft inthe LITE position).
12
Surface Cooking
Care & Seasoning of the Griddle
Using the Griddle
Care & Seasoning of the Griddle
Before first use:
Wash Griddle in hot soapy water. Rinse and then dry completely.
Apply a thin coat of vegetable oil to the entire surface (front and back of griddle).
Preheat your oven to 350°F. Place the griddle on the upper rack in your oven.
,,Bake griddle for 1 hour at 350°F,then turn oven OFF and letcool before removing.
,,The surface may appear to have a tacky feel to it from the seasoning process. If
desired, wash the griddle in hot soapy water, rinse well, and dry completely.
After each use:
To prevent rusting, store in a dry place and keep uncovered.
After each use, clean with a stiff brush and hot water only.
,,DO NOT CLEAN GRIDDLE IN DISHWASHER.
Dry Immediately and apply a light coating of vegetable oil to griddle before storing.
Using the Griddle:
Place either side of the griddle centered over the left side gas burners or over the
Bridge Burner (some models). For location refer to Fig. 1.
,, Preheat the griddle for 5 minutes on medium to medium low setting. Slow
preheat ensures even heat distribution during the cooking process.
DO NOT preheat the griddle on HI setting. Preheating on HI may warp the griddle
and prevent even heat distribution.
[ ¸ ;:iiii:i:
i .....
i
Fig. 1
Setting Warmer Drawer Controls
Arranging Warmer Drawer Racks
Using the Warmer Drawer
Arranging Warmer (Warm & Ready TM) Drawer Rack Positions
The rack can be used in two ways:
In the upward position (Fig. 2) to allow low profile food items to be placed both under and on top of the rack (for
example, rolls or biscuits on top of the rack and a casserole dish underneath).
In the downward position (Fig. 3) to allow you to place light weight food items and empty dishware (for example, rolls
or pastries and dinner plates) on the rack.
Always use
potholders or oven mitts
when removing food from
the Warmer Drawer as
cookware and plates will
be hot and you can be
burned.
Rack in upward
Fig. 2 position Fig. 3
Using the Warmer Drawer
WcarmerDrawer
k in downward
position
The purpose of the Warmer Drawer is to keep hot cooked foods at serving temperature. Always start with hot food. It is not
recommended to heat cold food in the Warmer Drawer. All food placed in the Warmer Drawer should be covered with a lid
or aluminum foil to maintain quality.
Do not use plastic wrap to cover food. Plastic may melt onto the drawer and be very difficult to clean. Use only
utensils and cookware recommended for oven use inthe Warmer Drawer.
Note: The Warmer Drawer will not operate during the Self-Clean cycle.
13
Setting Warmer Drawer Controls
,_ Warmer Drawer & Bread Proofing Indicator Lights
Setting Warmer Drawer & Bread Proofing Controls
Warmer Drawer Food Temperature Settings
Warmer (Warm & Ready TM) Drawer & Bread Proofing Indicator Lights
The control and indicator lights for the Warmer Drawer and Bread Proofing features are located on the control panel. The
indicator lights will turn ON when the control is set, and remain ON until the controls are turned OFF.
To Set the Warmer Drawer & Bread Proofing Controls:
2.
3.
4.
Touch the q I pad at the Warmer Drawer control position. The Warmer
Drawer indicator light will flash. Note: If no further pads are touched within 25
seconds the request to power the Warmer Drawer ON will clear.
Set the desired power level. Touch _/N_ once to turn ON the power level for HI
to turn ON the power level for LO (Fig. 4). The Warmer Drawer(Fig. 2)
or
v
indicator light will glow steady indicating the Warmer Drawer is ON.
Each touch of the CV-") or pads will decrease or increase through
6
v
power levels from Hi (Fig. 2) to MED (Fig. 3) to LO (Fig. 4) and to the Bread
Proofing feature (Fig. 5). Ifthe Warmer Drawer is set at the LO setting and the
(_pad is touched the Bread feature will be turned ON
again Proofing (The
Bread Proof indicator light will glow steady indicating the Bread Proofing feature
in ON (See Fig. 5 & bread dough preparation instructions on this page). To return
to standard Warmer Drawer settings touch CA_") pad at least once. Note: For
best results, preheat the Warmer Drawer before adding the food or bread dough.
An empty drawer will preheat in approximately 15 minutes.
When the food or dough is ready for removal, touch the ) pad once to turn
the Warmer Drawer or Bread Proof feature OFF. The Warmer Drawer indicator
light will turn OFF.
Warmer Drawer Food
Temperature Settings
Use the recommended Warmer Drawer
food temperature settings table (See Fig.
6). If a particular food is not listed, start
with the MED setting. If more crispness is
desired, remove the lid or aluminum foil
from the food.
Most foods can be kept at serving
temperatures on the MED setting. When a
combination of foods are to be kept warm
(for instance, a meat with 2 vegetables and
rolls), use the HI setting. To avoid heat
loss, do not open the Warmer Drawer
repeatedly while in use.
Warmer Drawer Recommended
Food Settings Table
Food item Setting
Bacon HI
Hamburger Patties HI
Poultry HI
Pork Chops HI
Fried Foods HI
Pizza HI
Gravies MED
Casseroles MED
Eggs MED
Roasts (Beef, Pork, Lamb) MED
Vegetables MED
Biscuits MED
Rolls, hard MED
Pastries MED
Rolls (soft) LO
Empty Dinner Plates LO
Fig. 6
' Hi
Med
Proof
Bread
Lo o
Warmer
Drawer
Fig. 1
Hi,
Med
Proof
Bread
Lo e
Fig. 2
Hio
0
Med
Proof
Bread
Lo o
Fig. 3
Hio
0
Med
Lo
Hi_
0
Med
Proof Proof
Bread _' Bread
'_ Lo
Fig. 4 Fig. 5
14
Warmer Drawer Removal
Preparing Bread Dough forthe Warmer Drawer
Removing & Replacing Warmer Drawer
Preparing Bread Dough for the Warmer Drawer
The Warmer Drawer has a "Proof Bread" feature that can be used to help
prepare bread dough. The recommended length of time to keep the bread
dough in the Warmer Drawer is about 45-60 minutes. Be sure however to
followthe recipe's recommended times.
The prepared bread dough should be placed in a large bowl because the
dough will nearly double in volume. Arrange the Warmer Drawer Rack in
the downward position (See Fig. 1). Place the bowl on the rack in the
Warmer Drawer and follow the Warmer Drawer and Bread Proof Control
setting instructions at the top of this page.
J
W_armer Drawer
Rackin downward
position
Fig.1
To Remove and Replace Warmer (Warm & Ready TM) Drawer
, Pullopw_thhogo_ To Remove Warmer Drawer:
1. _ Turn poweroff before removing the warmerdrawer.
2. Open the drawer to the fully opened position. ...........
3. Locate glide lever on each side of drawer, pull up on the left glide lever and
push down on the right glide lever (See Fig.2).
4. Pull the drawer away from the range. ....
To
1.
2.
3.
Replace Warmer (Warm & Ready TM) Drawer:
Pull the bearing glides to the front of the chassis glide (See Fig. 3).
Align the glide on each side of the drawer with the glide slots on the range.
Push the drawer into the range until levers "click" (approximately 2"). Pull
the drawer open again to seat bearing glides into position. If you do not
hear the levers "click" or the bearing glides do not feel seated
remove the drawer and repeat steps 1 thru 3. This will minimize
possible damage to the bearing glides.
Push down with fin_er
Fig. 2
Bearing Glide
Fig. 3
NOTE: The Warmer Drawer will NOT operate while in the Self,Clean and i!Oven
Lockout" modes
Electrical Shock Hazard can occur and result
in serious injury or death. Disconnect appliance from electric
power before cleaning and servicing the Warmer Drawer.
15
Electronic Oven Control Pad Features
DELAY START-- Use
with BAKE, COOK
TIME, and CLEAN to
program a Delayed
Timed Bake or Delay
Self-Cleaning cycle
start time.
COOKTIME--Use
to enter the length
of the baking time.
FLEX
CLEAN--Use
to select the
Self-Cleaning
feature (See
page 33).
READ THE INSTRUCTIONS CAREFULLY BEFORE USING THE OVEN. For
satisfactory use of your oven, become familiar with the various features and
functions of the oven as described below. Detailed instructions for each feature
and function follow later in this Use & Care Guide.
CONVROAST--
START-- Use to select the
Use to start Convection Roast
all oven BAKE--Useto for meats from a 0THRU 9
features enter the BROIL-- Use to variety of food NUMBER PADS-
(not used normal Bake select variable catagories. (See Use to enter
with Oven feature. Broil feature (See page 26). temperature and
Light). (See page 22). page 25). times.
-- Use to select
the Warm & Hold
feature (See
page 31).
SLOWCOOK--
Use to select the
Slow Cook feature
(See page 29).
CONV
CONVERT-- Use
to select the
Convection
Convert feature
(See page 28).
CLOCK--
Use to
set the
time of
day (See
page 17).
OVEN LIGHT--
Use to turn the TiMERON/
oven light ON OFF-- Use to
and OFF (See set or cancel
page 40). the Timer. The
Timer does not
start or stop the feature (See
cooking page 28).
process (See
page 18).
ADD 1 CONVBAKE-- PREHEAT-- CAKESor STOP -- Use to cancel
MINUTE-- Use to select Use to pre- BREADS--Use to any oven mode
Use to the Convection condition the select the cakes or previously entered
select Add 1 Bake feature oven breads from a except the time of day
Minute (See page 27). temperature variety of food and minute timer.
(See page catagories. (See Press STOP to stop
21). page 26). cooking. STOP also
controls the Oven
Lockout feature (See
page 19).
Minimum & Maximum Control Pad Settings
All of the features listed have
minimum and maximum time or
temperature settings that may be
entered intothe control. An ENTRY
acceptance beep will sound each
time a control pad istouched (the
Oven Lockout pad isdelayed by 3
seconds).
An ENTRY ERROR tone (3 short
beeps) will sound ifthe entry of the
temperature or time is below the
minimum or above the maximum
settings for the feature.
FEATURE
PREHEATTEMP.
BAKE TEMP.
BROILTEMP.
TIMER
CLOCKTIME
COOKTIME
STARTTIME
CLEANTIME
CONVECTION BAKE
12Hr.
24 Hr.
12Hr.
24 Hr.
12Hr.
24 Hr.
12Hr.
24 Hr.
MIN. TEMP./TIME MAX. TEMP./TIME
170°F / 77°C 550°F /288°C
170°F / 77°C 550°F /288°C
400°F / 205°C 550°F /288°C
0:01 Min. 11:59 Hr./Min.
0:01 Min. 11:59 Hr./Min.
1:00 Hr./Min. 12:59 Hr./Min.
0:00 Hr./Min. 23:59 Hr./Min.
0:01 Min. 11:59 Hr./Min.
0:01 Min. 23:59 Hr./Min.
1:00 Hr./Min. 12:59 Hr./Min.
0:00 Hr./Min. 23:59 Hr./Min.
2 hours 4 hours
170°F / 77°C 550°F /288°C
16
Setting Oven Controls
Setting the Clock
Changing between t 2 or 24 hour display
Silent Control Operation
Setting the Clock
The CLOCK _ pad is used to set the clock. The clock may be
set for 12 or 24 hour time of day operation. The clock has been
preset at the factory for the 12 hour operation. When the range is
first plugged in, or when the power supply to the range has been
interrupted, the timer in the display will flash with power failure "PF"
(See Fig. 1).
To set the clock (example below for 1:30):
1. Press (_. "CLO" will appear in the display (See Fig. 2).
to o, to
(See Fig. 3). Press (_. "CLO" will disappear and the clock
will start (See Fig. 4).
Changing between 12 or 24 hour time of day display:
1. Press and hold _ for 6 seconds untill "12h" or"24h"
appears in the display.
Press _cc_,-_to switch between the 12 and 24 hour time of
2.
day
display. "12h" or "24h" will be displayed (See Figs. 5 or 6).
3. Press _ to accept the desired change or press _ to
reject the change.
4. Reset the correct time as described in To set the clock above.
Please note that if the 24 hour time of day mode was chosen,
the clock will now display time from 00:00 through 23:59 hours.
Setting Silent Control Operation
G
Fig. 2
(_)for6seconds
Fig. 3
Fig. 4
Fig. 6
The DELAY START (,._'rtY)and FLEX CLEAN (,,_a'_ pads control the Silent Control operation feature. The Silent Control
operation feature allows the oven control to be operated without sounds or beeps whenever necessary. Ifdesired the control
can be programmed for silent operation and later returned to operating with all the normal sounds and beeps.
To change control from normal sound to silent control operation:
1. To tell if your range is set for normal or silent operation press
and hold _ss_a_tY-t_for 7 seconds.
(See Fig. 7)
Press _ to switch between normal sound operation and
2.
silent operation mode. The display will show either "SP" (See
Fig. 8) or" - -" (See Figs. 2 or 3).
_for 7seconds
If "SP" appears (See Fig. 2), the control will operate with normal
sounds and beeps. If " - -" appears (See Fig. 9), the control is
set for silent operation mode.
3. Press @ to accept the change or press Q to reject the @orQ
change.
17
Fig. 7
Fig. 8
Fig. 9
Setting Oven Controls
Continuous Bake or Twelve Hour Energy Saving Mode
]]mer
Setting Continuous Bake or 12 Hour Energy Saving
TIMER _-_si_oe_f_and FLEX CLEAN _ pads control the Continuous Bake or 12 Hour Energy Saving
The features. The
oven control has a factory preset built-in 12 Hour Energy Saving feature that will shut off the oven if the oven control is left
on for more than 11 hours and 59 minutes. The oven can be programmed to override this feature for Continuous Baking.
INSTRUCTIONS PRESS DISPLAY
To set the control for Continuous Bake or 12 Hour
Energy Saving features:
1. Press and hold _si_o_fr for 6 seconds or until the control beeps
once. (Fig.l). "12h" or "- - h" will appear in the display and the
control will beep once.
2. Press _c_,x,_to switch between the 12 Hour Energy Saving
and
continuous bake features. Note: "12h" (See Fig. 2) in the
display indicates the control is set for 12 Hour Energy Saving
feature and "- - h" (See Fig. 3) indicates the control is set for
the Continuous Bake feature.
(_ to accept the change (See Fig. 4) display
3. Press will
return to time of day) or press (_ to reject the change.
Fig. 1
Fig. 2
_for6seconds
Setting Timer
The TIMER _si_oef[_pad controls the Timer feature. The Timer serves as an extra reminder in the kitchen that will beep when
V
the set time has run out. The Timer will not START or STOP the cooking process. The Timer feature may be used during
any of the other oven control functions. Refer to "Minumum & Maximum Control Pad Settings" on page 16 for time amount
settings.
INSTRUCTIONS PRESS DISPLAY
Fig. 4
To set the Timer (example for 5 minutes):
1. Press _. (See Fig. 5).
2. Press the number pads to set the desired time in the display
_'-5_). Press _A'_. The timer will begin a count(example
v V
down. (See Fig. 6).
Note: If _ is not pressed the timer will return to the time of
day.
3. When the set time has run out, the clock will sound with 3 long
beeps every 5 seconds until _si_o_r is pressed (See Fig. 7).
Fig. 5
Fig. 6
To cancel the Timer before the set time has run out:
Press _. The display will return to the time of
day.
Fig. 7
18
Setting Oven Controls
Oven Lockout
Setting Temperature Display
OVEN
Setting Oven Lockout Feature IZCJLOCKOUT
The _ pad controls the Oven Lockout feature. The Oven Lockout feature automatically locks the oven door, prevents the
Warmer Drawer and most oven controls from being turned ON. It does not disable the clock, Timer or the interior oven light.
INSTRUCTIONS PRESS DISPLAY
To activate the Oven Lockout feature:
Press and hold _ for 3 seconds.
1.
2. After 3 seconds a beep will sound, Loc will appear and "DOOR
LOCKED" will flash in the display. Once the oven door is locked
the "DOOR LOCKED" indicator will stop flashing. (See Fig. 1)
Q for 3 seconds
Fig. 1
To reactivate normal oven operation:
Press and hold _ for 3 seconds. A beep will sound. Loc will
1.
clear. The "DOOR LOCKED" will continue to flash until the oven
door has completely unlocked (See Fig. 2).
Q for 3 seconds
2. The oven is fully operational.
Setting Temperature Display m Fahrenheit or Celsius
The BROIL ___Broil_and FLEX CLEAN _ pads control the Fahrenheit or Celsius temperature display modes. The oven
control can be programmed to display temperatures in Fahrenheit or Celsius. The oven has been preset at the factory to
display in Fahrenheit.
INSTRUCTIONS PRESS DISPLAY
Fig. 2
To change display from Fahrenheit to Celsius or
Celsius to Fahrenheit:
1. To tell if the display is set for Fahrenheit (F) or Celsius (C) press
_(See Fig. 3) 7 seconds; "550 °''
and hold for will first
appear in the display and then a beep will sound. If "F"
appears, the display is set to show temperatures in Fahrenheit
(See Fig. 4). If "C" appears, the display is set to show
temperatures in Celsius (See Fig. 5).
Press _cc_,-'_ to switch between Fahrenheit or Celsius
2.
display
V
modes. The display will show either "F" (See Fig. 4) or "C" (See
Fig. 5).
3. Press _ to accept the change or press _ to reject the
change.
_for 7 seconds
< orQ
19
Fig. 3
Fig. 4
Fig. 5
Setting Oven Controls
Saving & Recalling Recipe Settings
To Set the Recipe Recall Feature
The Recipe Recall feature may be used to record and recall your favorite recipe settings. This feature may store 1 setting
5 basic cooking pads. The key pads that a recipe may be stored with are BAKE _, CONV BAKE
A
for each of the
_, CONV ROAST _, CAKES _ & BREADS @. This feature will also store and recall Slow Cook,
Cook Time or Warm & Hold added setting. Pressing the START pad when entering cooking temperatures and times will
start the oven. if you wish to store the recipes but not start the oven press STOP after pressing the START pad.
Once a recipe has been stored with the recipe information will appear inthe display when pressing the pad in the future.
To store a typical cookie recipe: (example for baking at
375°F for 9 minutes and to shut=off automaticalJy):
INSTRUCTIONS
t. Arrange interior oven racks. Jfneeded, Preheat* the oven to the
desired set temperature. Place cookies on cookie sheet(s).
Place cookie sheet on the oven racks in the oven.
2. Press _ (See Fig.t).
3. Press ___ (See Fig. 2).
(See Fig. 2).
4. Press
5. Press _TCi°r,,°b (See Fig.3).
6. Enter the desired baking time. Press
(See Fig. 4).
7. Press _ and hold for 3 seconds (See Fig. 5 ). This recipe is
now stored with the BAKE key pad
When the Cook Time finishes:
t. "End" will display. The oven will shut-off automatically (See Fig. 7).
2. The control will beep 3 times. The control will continue to beep 3
times every 30 seconds until _ is
pressed.
*The Cook Time you enter does NOT include additional time required
to Preheat the oven. The oven will begin to count down the cooking
time as soon as the feature is activated.
To recalJ the cookie recipe stored under the _ key
1. Press _Sakej_ (See Fig. 6). The stored recipe is recalled.
(_ (See Fig. 5).
2. Press
To quickly erase all stored recipes:
1. Press and hold the _f7_'_ key pad until the first single beep sounds
(6 seconds).
beep press the _ key pad once. Any stored recipes
2. After the first
v
will be erased. Please Note: Clearing the recipes will also reset all other
adjustments back to the factory settings. These include 12 or 24 Hour
Time of Day display, Continuous Bake or 12 Hour Energy Savings
mode, Silent Control Operation, Fahrenheit or Celsius Temerature
Display, and any Oven Temperature adjustments.
PRESS DISPLAY
G
@
Hold for
3 seconds
@
Fig. 1
Fig. 2
Fig. 3
Fig. 4
Fig. 5
2O
Fig. 6
Fig. 7
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44

Kenmore Elite 79079443600 User manual

Category
Cookers
Type
User manual

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI