Agria 3600 Owner's manual

3600 911, 921 compact 2 + 2

3600 931, 941 comfort 3 + 3

3600 961, 971 premium 3 + 3 + Brake

Engine: EH 17 D

Before commissioning the machine, read operating

instructions and observe warnings and safety instructions.

Operating Instructions No.

998 762-A 04.12



Tool Carrier

3600 Unihamster

- compact

- comfort

- premium

Operating Instructions

Translation of the original operating instructions

2 Tool Carrier agria 3600 BM Unihamster

Symbols, Name Plate

Symbols

Warning – Danger

Important information

Choke

Fuel

Oil

Engine Start

Engine Stop

Engine speed

Engine oil level

Air filter

Air cooling

Transmission oil level

Visual check

Clutch

Mowing drive

Wheel drive

Forward

Reverse

PTO

Brake

Open (unlocked)

Closed (locked)

Clockwise

Anti clockwise

 agria-Service = contact your

agria workshop

Please complete:

Machine Type No.: .....................

Identification No.:

.................................................

Engine Type:

.................................................

Engine No.:

.................................................

Date of Purchase:

.................................................

For name plate, refer to page 3,

figure A/11.

For engine type and number, refer

to page 50, figure C/13.

Please state these data when

ordering spare parts to avoid

wrong deliveries.

Only use original agria spare

parts!

Specifications, figures and dimensi-

ons stated in these instructions are

not bind-ing. No claims can be de-

rived from them. We reserve the

right for improvements without chan-

ging these instructions.

This delivery comprises:

 Operating instructions

 Tool carrier

 Tool kit

 Knife driver

 2 Hex head boltsM 8

 2 Screw retentions M 8

Tool Carrier agria 3600 BM Unihamster 3

A

Designation of Parts

B

Compact Version

Comfort, premium Version

4 Tool Carrier agria 3600 BM Unihamster

Figure B

2 Hand lever for engine stop (safety circuit)

3 Hand clutch lever

4 Pawl for hand clutch lever

5 Eccentric lever for remote control of interlocking bolt

6 Shifter for wheel drive forfard and reverse

7 Shifter for attachment drive (mowing drive)

8 Shifter for wheel drive (gear shifter)

9 Locking screws for steering handle height adjustment

10 Locking lever for steering handle height adjustment

11 Speed control lever

12 Hand lever for forfard and reverse

13 Hand lever for operation brake, park brake - only premium version

14 Pawl for park brake - only premium version

Designation of Parts

Figure A

1 Mowing drive hood

2 Steering handle

3 Cutter bar

4 Mowing drive

5 Oil drain plug for mowing drive

6 Oil filler plug for mowing drive

7 Gearbox of basic machine

8 Hub with anti-winding tube

9 Transmission oil drain plug of basic machine

10 Transmission oil filling opening and dip-stick of basic machine

11 Name plate (in travel direction, right)

12 Engine

Tool Carrier agria 3600 BM Unihamster 5

Index

Symbols, Name Plate ....................... 2

Designation of Parts

Machine, Steering Handle ................ 3

Engine ............................................. 50

1. Safety Instructions ............... 7

Due Use ............................................ 7

2. Specifications

Gearbox compact, comfort ............. 13

Gearbox premium ........................... 14

Vibration Acceleration Value ..... 13, 14

Dimensions ..................................... 15

Track Width Plan ............................. 15

Mowing Drive .................................. 15

Engine ............................................. 16

Operation on Slopes ....................... 16

Noise Levels ................................... 16

3. Devices and Operating

Elements

Engine ............................................. 17

Safety Circuit ................................... 18

Clutch .............................................. 18

Brake Premium Version .................. 18

Gearbox .................................... 19, 20

Mowing Drive ............................ 19, 20

Steering Handle Adjustment ..... 19, 20

Coupling Attachments ..................... 21

Mowing Attachment ........................ 22

Drive-Wheels .................................. 24

Snow Chains ................................... 24

Twin-Wheels ................................... 24

Strake Wheels ................................. 24

4. Commissioning and

Operation

Commissioning the Machine .......... 26

Starting the Engine ......................... 28

Switching off the Engine ................. 29

Mowing ............................................ 30

5. Maintenance

Engine ............................................. 33

Air Filter ........................................... 34

Machine .......................................... 37

Safety Circuit ................................... 38

Mowing Drive .................................. 39

Mowing Attachment ........................ 40

Re-Grinding Mowing Knives ........... 41

General Maintenance, Cleaning ..... 42

Storage ........................................... 43

6. Troubleshooting ........... 46 - 47

Varnishes, Wear Parts ............ 44

Diagram: Electric Circuit ....... 44

Lubrication Chart ................... 45

Inspection and Maintenance

Chart ........................................ 48

Conformity Declaration ......... 51

Recommendations ................... 6

Note fold-out pages!

Fig. A + B................................... 3

Fig. C ....................................... 50

1

3

5

6

4

2

6 Tool Carrier agria 3600 BM Unihamster

Lubricants and Anti-

Corrosive Agents:

Use the specified lubricants for engine

and gearbox (see “Specifications”).

We recommend using bio- lubricating

oil or bio-lubricating grease for “open”

lubricating points or nipples (as

specified in the operating instructions).

We recommend using bio-slushing oil

for preservation of machines and im-

plements (do not apply on painted

external covers). Oil can be brushed or

sprayed on

Anti-corrosive agents are environ-

mentally friendly and degrade fast.

Using ecologically safe bio-lubricants

and bio-anti-corrosives, you contribute

to environmental protection and to the

wellbeing of humans, animals and

plants.

Fuel:

This engine runs perfectly using

commercially available lead-free Nor-

mal and Super petrol (also E10) as

well as Super plus.

Do not add oil to petrol.

If, for environmental reasons, you use

unleaded petrol, make sure the fuel is

drained completely when shutting down

the engine for more than 30 days. This

is to prevent resin residue from

depositing in the caburetor, fuel filter,

and tank. Or add a fuel stabilizer.

For further instructions see "Engine

Preservation".

Maintenance and Repair:

The trained mechanics of your agria

workshop carry out expert mainte-

nance and repair.

You should only carry out major mai-

tenance work and repairs on your own,

if you have the proper tools and

knowledge of machines and internal

combustion engines.

Do not hammer against the flywheel

with a hard object or metal tools as it

might crack and shatter in operation

causing injuries and damage. Only use

suitable tools for pulling the fly-wheel.

Recommendations

Tool Carrier agria 3600 BM Unihamster 7

1. Safety Instructions

Before starting the engine, read the op-

erating instructions and note:

Warning

W

This symbol marks all paragraphs

which affect your safety. Pass all safety

instructions to other users and opera-

tors.

Due use

The tool carrier is a hand-controlled

automatic single-axle machine which

can power and/or pull various imple-

ments approved by the manufacturer.

Areas of application are for such as

turning over the ground, mowing grass

and meadowland, snow clearance and

sweeping (due use).

Any other type of operation is consid-

ered undue. The manufacturer is not li-

able for any damages resulting from

undue use, for which the risk lies with

the user alone.

When the tool carrier is used on public

roads, the local national road traffic

rules must be observed, e.g. reflectors,

lights.

The tool carrier is not intended for use

with a trailer on public roads or as as a

tractor unit without implements.

Due use includes compliance with

manufacturer’s instructions on opera-

tion, maintenance and repair.

Any unauthorized changes to the

mower render manufacturer liability null

and void.

General Instructions on

Safety and Accident

Prevention

Basic Rule:

The standard accident prevention regu-

lations must be adhered to, as well as

all other generally accepted rules gov-

erning operational safety, occupational

health and road traffic regulations.

For drives on public roads, the national

traffic code applies.

Accordingly, check the tool carrier for

road and operational safety each time

you take up operation.

Only persons familiar with the mower

and instructed on the hazards of opera-

tion are allowed to use, maintain and

repair the mower.

Teenagers of 16 years or younger may

not operate the tool carrier!

Only work in good light and visibility.

Operator’s clothes should fit tight. Avoid

wearing loose fitting clothes. Wear solid

shoes.

Note the warning and instruction signs

on the mower for safe operation. Com-

pliance is for your own safety.

When transporting the mower on vehi-

cles or trailers outside the area to be

mowed, ensure that the engine is

turned off.

Careful with rotating tools – keep at a

safe distance!

1

8 Tool Carrier agria 3600 BM Unihamster

1. Safety Instructions

Beware of coasting tools. Before you

start any maintenance or repair on

them, wait until tools have come to a

complete stop.

Foreign powered parts shear and crush!

Riding on the attachment during opera-

tion is not permitted.

Implements and their weight affect the

driving, steering, braking, and tip-over

characteristics of the mower. Therefore,

ensure steering and braking functions

are sufficient. Match operating speed

to conditions.

Do not change settings of governor.

High engine speed increases risk of ac-

cidents.

Working Area and

Hazardous Area

The user is liable to third parties work-

ing within the mower’s working range.

Staying in hazardous area is not per-

mitted.

Check the immediate surroundings of

the mower before you start it. Watch out

for children and animals.

Before you start work, clear the area

from any foreign object. During opera-

tion, always watch out for further ob-

jects and remove them in time.

For operation in enclosed areas, ensure

that a safety distance is kept to enclo-

sures to prevent damage to tools.

Operation and Safety

Devices

Before you start the Engine

Become familiar with the devices and

operating elements and their functions.

Above all, learn how to turn the engine

off quickly and safely in an emergency.

Ensure that all protective devices are

mounted and positioned to provide pro-

tection.

With no implement mounted, make sure

PTO-shaft is covered with the protec-

tive cap.

Starting the Engine

Do not start engine in closed rooms.

The carbon monoxide contained in the

ex-haust fume is extremely toxic when

in-haled.

Before you start the engine set all op-

erating elements to neutral or idling po-

sition.

For starting the engine, do not step in

front of the mower and the implement.

Do not use assist-starting liquids when

using electrical assist-starting devices

(jumper cable). Danger of explosion!

Operation

Never leave the operator’s position at

the steering handle while mower is at

work.

Never adjust the operating handles dur-

ing work – danger!

During operation the operator must

keep at a distance as defined by the

steering handle, especially when turn-

ing the machine.

1

Tool Carrier agria 3600 BM Unihamster 9

1. Safety Instructions

Riding on the implement during opera-

tion or in transport is not permitted.

If clogging occurs in the implement, turn

off the engine and clean the implement

with an appropriate tool.

In case of damage to the tool carrier or

to the implement, immediately turn off

the engine and have it repaired.

If steering causes problems, immedi-

ately bring the mower to a halt and turn

it off. Have the malfunction removed

without delay.

To prevent the mower from sliding on

slopes, make sure it is secured by an-

other person using a bar or a cord. This

person must be located at a higher po-

sition than the vehicle and at a safe dis-

tance from the attachment at work.

If possible, always work horizontally on

the slope!

End of Operation

Never leave the mower unattended with

the engine running.

Before you leave the tool carrier, turn

off the engine.

Secure tool carrier against unauthor-

ized use. If mower is equipped with ig-

nition key, remove the key. For all other

versions, remove spark plug connector.

Implements

Only fit implements with the engine and

PTO switched off.

Always use appropriate tools and wear

gloves when changing implements and

parts thereof.

For fitting and dismounting implements

bring support leg into proper position

and ensure stability.

Secure mower and implements against

rolling off (parking brake, wheel

chocks).

Beware of injuries while coupling im-

plements.

Fit implements as specified and only

couple at specified points.

Secure mower and implement against

unauthorized use and rolling off when

you leave the machine. If necessary, in-

stall transport or security devices and

secure.

Mowing attachment

Handle with care! Sharp blades of the

cutter bar may cause injuries! Remove

protective knife strips only for mowing

and refit immediately after work has fin-

ished.

For transport and storage always fit the

protective knife strips. Secure finger

bars additionally with tension springs.

Do not transport the dismounted cutter

bar without protective strips.

Before fitting and dismounting the cut-

ter bar, make sure all blades are pro-

tected by the protective strip.

1

10 Tool Carrier agria 3600 BM Unihamster

1. Safety Instructions

To exchange the mowing knife and to

fit/dismount the knife driver, make sure

that you turn screws away from cutting

edges.

For grinding the mowing knives, always

wear safety goggles and gloves.

Weights

Always fit weights onto appropriate

weight fitting devices.

Snow clrearing

Ensure snow dozer is mounted cor-

rectly! Wear slip-proof shoes.

When swivelling the snow dozer watch

out for crush and shear points. Adjust

working speed to conditions. Operator

may be injured when the mache comes

in contact with solid objects.

Maintenance

Never carry out any maintenance or

cleaning with the engine running.

Before you work on the engine, always

remove spark plug connector (petrol

engine only).

Check regularly and, if necessary, re-

place all protecting devices and tools

subject to wear and tear.

Replace damaged cutting tools!

Always wear safety gloves and use

proper tools when exchanging cutting

tools!

Do not carry out repairs like welding,

grinding, drilling, etc. on structural and

safety-relevant parts (e.g. steering han-

dle, coupling devices)!

Keep mower and implement clean to

avoid risk of fire.

Check nuts and screws regularly for

tight fit and re-tighten, if necessary.

After maintenance and cleaning, en-

sure that you re-install all safety and

protective devices and adjust them

properly.

Only use original agria spare parts.

All other commercial spare parts must

correspond to quality and technical re-

quirements specified by agria.

Storage

It is not allowed to store the mower in

rooms with open heating.

Never park the mower in closed rooms

with fuel left in tank. Fuel vapours are

hazardous.

1

Tool Carrier agria 3600 BM Unihamster 11

1. Safety Instructions

Engine, Fuel and Oil

Never let the engine run in closed

rooms. Extreme danger of intoxication!

For the same reason, also replace dam-

aged exhaust parts immediately.

Caution with hot engine parts!

The exhaust and other engine parts

become very hot, if the engine runs and

immediately after turning off. Hold for

sufficient distance from hot surfaces

and keep children away from the

running engine.

Be careful when dealing with fuel. Great

danger of fire! Never refill fuel close to

open fire, inflammable sparks or hot

engine parts. Do not refill fuel in closed

rooms. Do not smoke when refilling!

Refill only with the engine switched off

and cooled down.

Do not spill any fuel, use a proper fill-

ing device.

In case of fuel spillage, pull the tool

carrier away from the spillage before

you start the engine.

Make sure fuel is of specified quality.

Store fuel in approved cans only.

For safety reasons the petrol tank and

fuel cap should be replaced regularly.

Store anti-corrosive agents and stabiliz-

ing liquids out of reach of children. If sick-

ness and vomiting occur, see a doctor. If

fuel has contacted eyes, rinse them thor-

oughly, avoid inhaling of vapours.

Read and observe enclosed instruc-

tions.

Before you dispose of opened and

seemingly empty pressurised tins (e.g.

of assist-starting liquids) make sure

they are completely empty. Empty them

1

in ventilated places safe from spark for-

mation or flames. If necessary, dispose

of tins in hazardous waste deposits.

Be careful when draining hot oil, dan-

ger of burns.

Make sure oil is of specified quality.

Storage is in approved cans only.

Dispose of oil, greases, and filters

seperately and properly.

Tyres and Tyre Air

Pressure

When working on tyres, make sure tool

carrier is parked properly and secured

against rolling off.

Any repairs are to be carried out by

trained mechanics only and with the

appropriate tools.

Regularly check tyre air pressure. Ex-

cessive pressure may cause bursts.

Use appropriate tyre air pressure when

fitting weights or implements.

Re-tighten attachment bolts of drive-

wheels or check tightness when doing

maintenance work.

Electrical System

Persons having a pacemaker must not

touch live parts of ignition system when

the engine is running!

12 Tool Carrier agria 3600 BM Unihamster

1. Safety Instructions

Explaining of Warning

Signs

Before any cleaning, maintenance, and

repair work switch off the engine and

pull spark plug connector.

With engine running, keep at a safe dis-

tance from cutting tools!

Do not work without protective devices!

Do not start the engine without having

the protective devices positioned to pro-

vide protection.

With engine running, keep a safe dis-

tance to cutting tools!

Do not touch coasting tools. Wait until

tools have come to a complete stop.

With engine running, keep at a safe dis-

tance.

Signs

When working with the

machine, wear individual

protective ear plugs.

Wear protective gloves.

Wear solid shoes.

1

Tool Carrier agria 3600 BM Unihamster 13

2. Specifications

2

Comfort Version

Type: ...................................................

............ Unihamster comfort 3600 931

with mowing drive

............ Unihamster comfort 3600 941

without mowing drive

Tyre: .............. 16 x 6.5-8 (Ackerprofil)

Tyre air pressure: .................. 1,2 bar

Weight: with mowing drive ................

...................................... approx. 99 kg

(without cutter bar)

without mowing drive approx. 83 kg

Clutch:

.................................... Disc dry clutch

Getriebe: .......... Mechanical gearbox,

Reversing gearbox

2 forward speeds and 2 reverse

speeds

Filling quantity:

....................................... approx. 1,5 l.

Transmission oil SAE 90-API GL5

(e. g. BP Energear Hypo)

Travel Speeds:

Steering handle: ..... rubber mounted

height adjustable without tools.

Vibration acceleration value:

on handlebar grip ..... a

hw

= 13,68 m/s

2

in accordance with 2002/44/EG; EN 12733:2001

Compact Version

Type: ...................................................

.......... Unihamster compact 3600 911

with mowing drive

.......... Unihamster compact 3600 921

without mowing drive

Tyre: .................... 4.00-8 (Ackerprofil)

Tyre air pressure: .................. 1,2 bar

Weight:with mowing drive .................

...................................... approx. 90 kg

(without cutter bar)

without mowing drive approx. 74 kg

Clutch:

.................................... Disc dry clutch

Getriebe: .......... Mechanical gearbox,

2 forward speeds and 2 reverse

speeds

Filling quantity:

....................................... approx. 1,5 l.

Transmission oil SAE 90-API GL5

(e. g. BP Energear Hypo)

Travel Speeds:

Steering handle: .. height adjustable.

Vibration acceleration value:

on handlebar grip ....... a

hw

= 31,2 m/s

2

in accordance with 2002/44/EG; EN 12733:2001

1. 2. R 1. R 2.

km/h 1,93 3,82 1,21 2,37

4.00-8

1. 2. 3.

km/h 1,73 2,78 3,88

km/h 1,35 2,16 3,02

16 x 6.5-8

14 Tool Carrier agria 3600 BM Unihamster

2. Specifications

Premium Version

Type: ...................................................

......... Unihamster premium 3600 961

with mowing drive

......... Unihamster premium 3600 971

without mowing drive

Tyre: ................. 16 x 6.5-8 (field tyre)

Tyre air pressure: .................. 1,2 bar

Weight: with mowing drive ................

.................................... approx. 102 kg

(without cutter bar)

without mowing drive approx. 86 kg

Clutch:

.................................... Disc dry clutch

Gearbox: .......... Mechanical gearbox,

Reversing gearbox

3 forward speeds and 3 reverse speeds

operation and park brake

Filling quantity:

....................................... approx. 1,5 l.

Transmission oil SAE 90-API GL5

(e. g. BP Energear Hypo)

Travel Speeds:

Steering handle: ..... rubber mounted

height adjustable without tools.

Vibration acceleration value:

on handlebar grip ..... a

hw

= 13,68 m/s

2

in accordance with 2002/44/EG; EN 12733:2001

2

1. 2. 3.

km/h 1,73 2,78 3,88

km/h 1,35 2,16 3,02

16 x 6.5-8

Tool Carrier agria 3600 BM Unihamster 15

2. Specifications

Mowing drive

 Centrally driven oil bath rocker

arm mowing drive

for universal, municipal cutter bar and

cutting bar

Stroke: ...................................... 76 mm

Stroke speed: ..................... 943 min

-1

Transmission oil for mowing drive:

................................. SAE 90-API GL5

Filling quantity approx. 0,5 l.

Track Width Plan

[mm]

a = 910

b = 570

e = 510

h = ca. 990

l = 1780

m = 1170

S=

A=

}

refer to track width plan

Dimensions [mm]

AS i A A

4.00-8

510 400 290 900 880

16 x 6.5-8

610 455 290 - -

2

16 Tool Carrier agria 3600 BM Unihamster

2. Specifications

Engine

Manufacturer: ........................... Robin

Type: ..................................... EH 17 D

Version:

Fan-cooled 1-cylinder 4-stroke engine

(petrol)

Bore: ........................................ 67 mm

Stroke: ..................................... 49 mm

Cubic capacity: ................... 172 ccm

Output: ............ 4,0 kW at 3600 min

-1

Torque:

................. max. 11 Nm at 2600 min

-1

Spark plug: ............. BOSCH WR7AC

NGK BR 6 HS

Electrode gap: 0,6 - 0,7 mm

Ingnition system::

Contactless electronic magnet

ignition, ignition point is pre-set, radio

remote, screened according to VDE

0879

Valve lash (engine cold)

Intake ......................... 0,08 - 0,11 mm

Outlet ......................... 0,08 - 0,11 mm

Starter: ......................... Recoil starter

Fuel tank capacity: ...... approx. 3,6 l.

Fuel: ........................... lead-free petrol

(refer to fuel recommendations)

Air filter: ................. Dry filter element

with foamed preliminary filter

Carburetor: ...... orizontal throttle float

carburetor

Mixture Control Screw:

Base setting approx. 1 3/8 revs. open

Main jet ......................................... 105

Idle jet ............................................. 50

Rated speed: ................... 3600 min

-1

Top no-load speed: ......... 4000 min

-1

Idling speed: ................... 1200 min

-1

Engine oil: ................. Filling quantity

..................................... approx. 0,65 l.

Multi-grade oil SAE 10 W-40 API-SC

or higher quality

Operability on Slopes:

Engine is suited for use on slopes

(with oil level at “max” = upper level

mark)Continuous operation possible

up to.................45° inclination (100%)

Noise level:

In accordance with EN 12733 and

EN ISO 11201:

Noise level at operator’s ear ..............

................................... L

pA

= 84,5 dB(A)

Acoustic power level: ..........................

................................ L

WA

= 103,3 dB(A)

2

Tool Carrier agria 3600 BM Unihamster 17

3. Devices and Operating Elements

The agria tool carrier 3600 is a basic

mtorised unit and is always used with

an implement. Therefore it is most suit-

able for normal use in landscape gar-

dening and in agriculture and forestry

work for such as turning over the

ground, mowing grass and

meadowland, snow clearing and

sweeping.

When the single-axle tractor/the tool

carrier/the all-purpose machine is used

on public roads, the local national road

traffic rules must be observed, e.g. re-

flectors, lights.

Available attachments:

 Cutter bars in different versions and

work widths.

 For attachments as sickle mower,

tedder, road-sweeper, rotary snow

cleaning and snow-plough refer to our

price-list.

 For a choice of further attachments

z. B. Gitterräder, refer to our price-list.

Engine

 The four-stroke petrol engine runs on

commercial petrol.

 refer to fuel recom-mendations p 6.

During the first 20 operating hours

(break-in period) do not use engine to

maximum power. Even after break-in

period never use engine at higher

speed than necessary for the work in

hand.

I

High engine speed is harmful

to any engine and considerably

affects its durability. This applies es-

pecially for no load operation. Any

overspeed (have the engine roar) can

result in immediate damage.

Cooling system

Cooling system is fan-cooled. Therefore

keep grille at recoil starter and cooling

fins of cylinder clean and free from

sucked-in plant trash.

Idling speed

Always ensure that idling-speed is ad-

justed correcty. At low speeds and with

the speed control lever set to idle, the

engine is supposed to run smoothly and

without run-out.

Air filter

The air filter purifies the air taken in. A

clogged filter affects engine output.

Ignition system

The engine is equipped with a mainte-

nance-free, contactless electronic igni-

tion system. We recommend to have

necessary check-ups done by an ex-

pert only.

Speed control lever

The speed control lever (B/11) on the

steering handle is for stepless control

of engine speed from min = IDLING to

max = FULL THROTTLE to fit require-

ments.

3

18 Tool Carrier agria 3600 BM Unihamster

Safety circuit

 Stop position: When releasing the lever (B/2) the igni-

tion system is switched off (engine is shut off).

- Beware! Engine keeps running due to centrifugal mass.

Start position: For starting the engine and for short

breaks press down the safety circuit lever, pull the clutch

lever (B/3) and lock with pawl (B/4).

 Operating position:To operate the machine, press

down the safety circuit lever (B/2).

W

Do not tie down the safety circuit lever! Check

safety circuit for proper function each time you

take up operation!

I

Release the safety circuit lever in an emergency,

the lever will automatically go to STOP position!

Clutch

 The mower is equipped with a disc dry clutch which is

operated via the hand clutch lever (B/3).

With hand clutch lever pulled to position “0”, the clutch is

decoupled, i.e. the engine stops driving the tool carrier.

 Watch for the correct clutch play to avoid clutch slip-ping

away during operation.

I

With the engine running, do not park the power

mower for an extended period of time while the clutch

is pulled because this may result in damage to the clutch

release bearing.

 With the engine stopped, always park the tool carrier

with the hand lever pulled (pawl is locked into place), oth-

erwise clutch problems may occur due to corrosion.

Brake only premium version

 Brake unlocked

 Operation brake - Pull hand lever (B/13)

 Park brake - Pull hand lever (B/13)

- lock with pawl (B/14)

3. Devices and Operating Elements

3

B/2

B/4

B/3







37













Tool Carrier agria 3600 BM Unihamster 19

3

Gearbox compact Version

I

Only change gears when the machine is stopped

(decoupled)!

The tool carrier is eqipped with a mechanical gearbox with 2

forward speeds and 2 reverse speeds.

Changing gears

 Gear change V1, V2 and R1, R2 is via gear shifter (B/6)!

 Gears are changed via neutral position in the shift gate.

Mowing Drive Compact Version

(PTO driven)

The mowing knives are driven by rocker arm drive via PTO on

basic machine.

PTO Speed Change

Shifter (B/7) is for turning on/off the mowing drive or the PTO

driven implement.

 Move shifter forward = off;

 Move shifter backward = on.

Steering Handle Compact

Version

Steering Handle Height Adjustment

 Loosen the locking bolts (B/9).

Adjust handlebar to desired height.

Fasten the locking bolts.

3. Devices and Operating Elements

B/6

B/7







20 Tool Carrier agria 3600 BM Unihamster

3

Gearbox Comfort and Premium Version

I

Only change gears when the machine is stopped

(decoupled)!

The tool carrier is eqipped with a mechanical gearbox with 3

forward speeds and 3 reverse speeds.

Changing gears

 Gear change 1-2-3 is via gear shifter (B/8)!

 Gears are changed via neutral position in the shift gate.

Shifter V-R

Travelling direction change via shifter V-R (B/12).

PTO Drive Comfort and Premium Version

The drive for the attachments is obtained from the power take-

off shaft on the base unit.

The mowing knives are driven by rocker arm drive via PTO on

basic machine.

PTO Speed Change

Shifter (B/7) is for turning on/off the mowing drive or the PTO

driven implement.

 Move shifter forward = off;

 Move shifter backward = on.

Steering Handle Comfort and

Premium Version

Steering Handle Height Adjustment

 Press down locking lever (B/10) until notches

are free.

 djust handlebar to desired height.

 Release locking lever and fit handle-bar into

proper notch, so that locking lever wivels back

into its original position.

3. Devices and Operating Elements

B/8

B/12

B/7

B/10

Page is loading ...

Agria 3600 Owner's manual

Agria 3600 Owner's manual

Related papers

Other documents