Bosch SGV43E43EU/33 Brief description

SGV43E43EU/33
Bosch
Brand
Bosch
Model
SGV43E43EU/33
Type
Brief description

This manual is also suitable for

Brief Instructions: Dishwasher
Short and handy: everything
your dishwasher needs...
Before using for the first
time, read the Installation
and Operating Instructions!
Switch appliance ON, off we go...
Press main switch, choose programme.
Close door.
Signal sounds, open door. End-of-programme
indicator flashes, press main switch.
Switch appliance OFF, everything OK...
Add rinse-aid.
Add detergent.
Select programme.
Add salt.
9000 277 719  
en
Setting the water softening system *
Quickly sorted
Find out the water
hardness at your water
utility company and
enter below
* only before using the
dishwasher for the first
time or if the water hard-
ness changes
Read off the setting
Setting°dH °fH °Clarke mmol/l
and then select a setting
– Hold down programme button B and switch on the main
switch, then release the buttons. The . display flashes and
buttons A and B illuminate (water hardness setting was set
to 2 at the factory).
– Each time button B is depressed, the setting increases by
one (0-3). If buttons A, B and C illuminate, the maximum
water hardness setting has been reached. If the water
hardness setting is now increased again, the lights go out
and the water hardness setting is set to 0.
– Switch off the main switch. The selected setting has been
stored in the appliance.
0
1
2
3
Reset
A B C
22–35
0–6
7–16
17–21
0–1,1
1,2–2,9
3,0–3,7
3,8–6,2
9–20
0–11
12–29
30–37
38–60
0–8
21–26
27–44
Dissolves limescale (not required for set value 0!)
Unscrew
the lid.
Only before using
the dishwasher
for the first time
pour approx. 1 l /
1 1/4 pt water into
the salt opening.
Pour in max.
1.5 kg / 3 lb 5 oz
salt (never deter-
gent!)
Screw on the
lid. Switch on
dishwasher
immediately.
Everything is sparkling clean ... Refill whenever level indicator is light!
Press mark 1,
lift up lid 2.
Pour in
rinse aid.
Close the
lid. CLICK!
Very dirty dishes, a lot of detergent ...
If required, open
the lid (press the
pin).
Warning,
combination
products are not
suitable for all
programmes,
follow manufac-
turer’s instructions.
Pour in
detergent.
Push the lid
shut, press.
PLOP!
Quick, economical or intensive ...
This overview indicates the max. possible number of
programmes. The programmes which correspond to your
appliance can be found on your appliance fascia.
The programme data are values measured in the
laboratory in compliance with Standard EN 50242.
Deviations is practice are possible.
Overview of programmes
115
1,70
21
140
1,05
14
75
0,90
15
30
0,70
10
19
0,10
4
35_ 50_ 70_ 65_ 40_
Duration in minutes
Power consumption in kWh
Water consumption in litres
Intensive
Normal Eco Gentle
Quick Prerinse
140
1,60
19
Additional programmes **
Increased flexibility ...
** on some models
Extra dry
... improves the drying
result by increased
temperature in the final
rinse (Please take care
with delicate dishes)
Upper basket cleaning
...Only the crockery in the
upper basket is cleaned
Half load
... for a few items, saves
water, energy and time
Maintenance and care
For perfect rinsing results
Waste water pump *
Filters
Check and,
if required,
clean:
Rotate filter cylinder,
remove filter system
Rinse under
running water
Insert
Screw on filter
system.
NOTE MARK!
* some models
– Set main switch to OFF
– Scoop out any water
– Remove the filters
– Remove the cover (⇒A)
– Check the inner compartment for foreign
objects and, if required, remove foreign
objects
– Re-insert the cover (⇒B)
– Re-insert the filters and screw into position
– Re-insert the cover (⇒B)
– Re-insert the filters and screw into position
Spray arms
Remove blockages/
deposits
Pull up lower arm
Clean under running
water (if required,
use a toothpick)
Insert lower arm
Screw on upper arm
click
3
deposits
Unscrew upper arm
A
2
3
B
Rectifying minor faults yourself ...
... as it is worth doing it yourself!
Fault Possible causes Remedial action
Plastic/utensils
discoloured
Too little detergent Follow manufacturer’s instructions
(detergent).
“Check water supply”
display lights up
Supply fitting jammed or calcified Open supply fitting.
Residual water in the
appliance and “Check
water supply” display
lights up
Waste water pump blocked Clean waste-water pump (see above).
1. Unscrew water connection.
2. Clean filter in the water connection.
3. Flow rate must be min. 9 l/min.
when water supply is open.
If the flow rate is less, replace the
supply fitting.
Install supply hose without kinks.
The programme has not yet ended
Waste water hose is blocked or kinked
Close the appliance and wait until
the programme ends
(end of programme display is lit)
or terminate the programme
(see Terminating the programme).
Install waste water hose without kinks.
Discoloration caused by food
colourings (tomato sauce)
Discoloration is harmless; subsequent
rinse cycles will cause it to fade.
Fault Possible causes Remedial action
Stains and streaks
Milky deposits
on the utensils
(can be removed)
Rust on the cutlery
Rinse-aid dosage too high/too low
Glasses not dishwasher-proof
Cutlery not rust-resistant
Hard knife blades are more susceptible
Streaks: reduce dosage.
Use dishwasher-proof glasses.
Use dishwasher-proof cutlery.
More information can be found in the operating instructions
Milky deposits, glasses
cloudy/tarnished
(cannot be removed)
Water softening system incorrectly set; Correctly set water softening system.
Utensils are not clean
Sand or gritty residue
on the utensils
Utensils are situated close together
or one above the other
Separate the utensils, prevent contact
points.
Too little detergent
Unsuitable programme selected
Spray arm nozzles blocked
Filters dirty, not seated firmly
Spray arms blocked
Follow manufacturer’s instructions
(detergent).
Select a more intensive programme.
Clean the spray arms (see above).
Clean the filters (see above).
Arrange the utensils so that the spray
arms can rotate freely.
Water or limescale stains: increase
dosage.
No salt Refill with salt.
Use a detergent suitable for glasses.
Extraneous rust Never wash rusting parts in the
appliance.
Interrupting the programme ... Terminating the programme ...
Arranging dishes correctly ...
– Open the door.
– Press the two RESET
buttons simultaneously
(approx. 3 seconds)
(RESET).
– Close the door.
– Open the door.
– Press the START/STOP
button.
– To continue, press the
START/STOP button again.
– Close the door.
Switch off the
appliance.
After 1 minute the
programme ends.
The ”signal
sounds and the
standby indicator
illuminates”.
Arrange dishwasher-proof dishes in accordance with the operating manual
(without residual ash, wax, lubricating grease, ink, sticky labels; remove any
large remnants of jam, milk products or food) and check that the spray arms
can rotate freely.
  • Page 1 1
  • Page 2 2

Bosch SGV43E43EU/33 Brief description

SGV43E43EU/33
Bosch
Brand
Bosch
Model
SGV43E43EU/33
Type
Brief description
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents