2. Minka Group
  3. 4102-66

Minka Group 4102-66, 4102-84 User manual

  • Hello! I've analyzed the installation instructions for the 4102-66/84/172 light fixture. The document guides you through the complete installation process, from shutting off the power to installing the bulb. I'm ready to answer any questions you might have about the fixture setup, wiring, and safety precautions.
  • What should I do before starting the installation?
    How do I attach the mounting plate?
    How do I connect the wires?
    What type of bulb can I install?
INSTALLATION INSTRUCTIONS
Item#4102-66/84/172 (New. 2022/12/30)
READ AND SAVE THESE INSTRUCTIONS
W A R N I N G ! S H U T P O W E R O F F AT F U S E O R C I R C U I T B R E A K E R .
AVERTISSEMENT! COUPER LE COURANT AU NIVEAU DES FUSIBLES OU DU DISJONCTEUR.
Page: 1/1
Fig. 1
Fig. 2
LA-3619E
PREPARATION (Fig.1)
1. Shut off power at the fuse box or circuit breaker box and
remove the old fixture including the mounting hardware.
2. Carefully unpack your new fixture and lay out all the parts
in a clean area. Take care not to misplace any small parts
necessary for installation.
3. Determine the desired hanging height and thread rods
(F1, F2 and F3) onto all thread (G). Attach canopy (D)
by
threading onto rod (F1). Carefully pass
wires through each
rod during assembly.
4. Attach mounting plate (A) to the junction box (not
included) with mounting screws (B) (Size: #8-32N*L0.5”).
The side of the mounting plate (A) with “GND” marked on
it and two convex points must face out.
CONNECTING THE WIRES (Fig. 2)
5. Connect the electrical wires as shown in Fig 2, making
sure that all wire connectors are secured. If your
junction
box has a ground wire (green or bare copper), connect
fixture’s ground wire to it. Otherwise, connect fixture’s
ground wire directly to the mounting plate (A) using green
screw provided.
6. Tuck wire connectors neatly into the junction box.
COMPLETING THE INSTALLATION (Fig. 1)
7. Place canopy (D) over mountin
g plate (A) and secure with
screws (E).
8. Place large glass shade (I), metal cover (J), small glass
shade (K), metal ring (L) over the socket (H), then secure
with screw shell (M).
9. Install (1) one medium base bulb (N) up to100 watts each
or CFL or LED equivalent (not included) in accordance
with the fixture specification. —
DO NOT EXCEED THE
MAXIMUM WATTAGE RATING! (NE PAS DEPASSER
LA PUISSANCE NOMINALE MAXIMALE!)
Your insta
llation is now complete. Return power to the
junction box and test the fixture.
Note:
Illustration (Fig. 1) on this manual is for
installation purposes only. It may or may not be
identical to the fixture purchased.
Set# A-021-118DH
-Mounting plate
-Ground screw
-Mounting screw *2
WIRES
Black or
Smooth
HOUSE
WIRES
Black
(Hot)
FIXTURE
WIRES
White or
Ribbed
HOUSE
WIRES
White
(Neutral)
FIX
TURE
WIRES
Bare
Copper
(Ground)
HOUSE
WIRES
Green
(Ground)
Rod# W30-1-66/84/172 *1 (F1)
W30-1-66/84/172 *2 (F2)
W30-H-66/84/172 *1 (F3)
F1
G
I
J
K
L
M
N
H
F3
F2
A
B
E
D
/