Silvercrest 282713 Owner's manual

DESIGNER POWER BANK

CARGADOR CENTRAL SPBD 5000 A1

IAN 282713

DESIGNER POWER

BANK

Operating instructions

CARGADOR CENTRAL

Instrucciones de uso

US-EN Operating instructions Page 1

US-ES Instrucciones de uso Página 23

Before reading, unfold the page containing the illustrations and

familiarize yourself with all functions of the device.

Antes de empezar a leer abra la página que contiene las

imágenes y, en seguida, familiarícese con todas las funcio-

nes del dispositivo.

SPBD 5000 A1 US-EN │ 1 ■

Contents

Introduction ..............................3

Information about these operating instructions ...........3

Copyright .......................................3

Intended use .....................................4

Safety ..................................6

Basic safety instructions ............................6

Description of components .................9

Use ....................................10

Check package contents ......................... 10

Disposal of the packaging ........................ 10

Charging the power bank ........................ 11

Checking the charge level ........................ 12

Handling and use ........................13

Charging mobile devices with the power bank ........ 13

Troubleshooting .........................14

Cleaning. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Storage when not in use ..................15

Disposal ................................16

SPBD 5000 A1

■ 2 │ US-EN

Appendix ...............................17

Technical data ................................. 17

FCC Compliance Statement ....................... 18

Warranty ..................................... 20

Distributor ..................................... 22

SPBD 5000 A1 US-EN │ 3 ■

Introduction

READ ALL INSTRUCTIONS BEFORE USE

Information about these operating

instructions

Congratulations on the purchase of your new

device.

■ You have selected a high-quality product.

■ The operating instructions are part of this product.

■ They contain important information about safety, use and

disposal.

■ Before using the product, please familiarize yourself with

all operating and safety instructions.

■ Use the product only as described and for the range of

applications speciﬁed.

■ Retain these instructions for future reference.

■ Please also pass these operating instructions on to any

future owner.

Copyright

USB® is a registered trademark of USB Implementers Forum, Inc.

All other names and products may be trademarks or registered

trademarks of their respective owner.

SPBD 5000 A1

■ 4 │ US-EN

Intended use

■ This device is an information technology device and is

intended exclusively for charging mobile devices that are

charged via a USB port as standard.

■ The device is not intended for any other purpose, nor for

use beyond the scope described.

■ The device is not intended for use in commercial or indus-

trial environments.

■ The manufacturer accepts no responsibility for damage

caused by failure to observe these instructions, improper

use or repairs, unauthorized modiﬁcations, or the use of

unapproved replacement parts. The risk is borne solely by

the user.

Warnings used

The following warning types are used in these operating

instructions:

► WARNING indicates a hazardous situation which, if not

avoided, could result in death or serious injury.

► CAUTION indicates a hazardous situation which, if not

avoided, could result in minor or moderate injury.

SPBD 5000 A1 US-EN │ 5 ■

► NOTICE indicates information, which is considered impor-

tant, but not hazardous (e. g. messages related to property

damage).

A "Tip" indicates additional information that will assist you in

using the device.

Terminology

As used in this instruction manual in general and with

regard to safety information and warnings, the following

words are assumed to mean:

■ May: This word is understood to be permissive.

■ Shall: This word is understood to be mandatory.

■ Should: This word is understood to be advisory.

SPBD 5000 A1

■ 6 │ US-EN

Safety

This section contains important safety instructions for hand-

ling the device. This device complies with statutory safety

regulations. Improper use may result in personal injury and

property damage.

Basic safety instructions

■ Check the device for visible external damage before use.

Do not operate a device that has been damaged or

dropped.

■ Risk of suﬀocation!

Do not allow children to play with the packaging material!

Keep all packaging materials away from children.

■ This device may be used by children aged 8 years and

above and by persons with limited physical, sensory or

mental capabilities or lack of experience and knowledge.

Only, if it is provided that they are under supervision or

have been told how to use the device safely and are

aware of the potential risks.

■ Children must not play with the device.

■ Cleaning and maintenance shall not be carried out by

children unless they are supervised.

■ Always place the device on a stable

and level surface. It can be damaged if dropped.

SPBD 5000 A1 US-EN │ 7 ■

■ Do not place the product near heat sources such as radia-

tors or other heat-generating devices.

■ Do not operate the device close to

open ﬂames (e.g. candles).

■ The device is not designed for use in rooms with high

temperatures or humidity (e.g. bathrooms) or where there

is excessive dust.

■ Do not expose the device to direct

sunlight or high temperatures and do not cover it during

charging. Otherwise, it may overheat and be irreparably

damaged. This particularly applies to storage in a car.

Extreme temperatures can occur in car interiors and glove

compartments during long periods of immobilization.

Remove electrical and electronic devices from the vehicle.

■ Do not use the device immediately after moving it from a

cold room to a warm room. Always allow the device to

acclimatize before turning it on.

■ Never open the device housing.

None of the components in the device can be serviced or

replaced by the user.

■ Do not make any unauthorized modiﬁcations or altera-

tions to the device.

SPBD 5000 A1

■ 8 │ US-EN

■ All repairs must be carried out by

authorized service centers or by the customer service

department. Improper repairs may put the user at risk. It

will also invalidate any warranty claims.

■ Do not expose the device to water spray or dripping

water, and do not place liquid-ﬁlled objects such as

vases or open drink containers on or near the device.

■ Turn the device oﬀ immediately and disconnect any con-

nected charging cables from the device if you smell

fumes, or notice any smoke. Have the device checked

by a qualiﬁed specialist before using it again.

■ If you are using a USB power supply, the socket you use

must always be easily accessible so that the USB power

supply can be quickly disconnected from the socket in a

hazardous situation. You should also observe the operat-

ing instructions for the USB power supply.

■ Improper use of the batteries can cause

ﬁres, explosions, leakages or other hazards! Do not throw

the device into a ﬁre as the integrated battery could

explode.

SPBD 5000 A1 US-EN │ 9 ■

■ Note any restrictions or prohibitions on use for battery-

powered appliances in locations with speciﬁc hazard

risks, such as gas stations, airplanes, hospitals, etc.

Description of components

(See fold-out page for illustrations)

Power Bank SPBD 5000 A1 (model example)

micro-USB charging port (IN)

Charge level LEDs

USB socket (OUT)

ON/OFF button (ON/OFF)

Charging cable (USB to micro-USB)

Operating instructions (symbol image)

SPBD 5000 A1

■ 10 │ US-EN

Use

Check package contents

(See fold-out page for illustrations)

The product includes the following components:

▯ Designer Power Bank SPBD 5000 A1

▯ Charging cable

▯ These operating instructions

♦ Remove all parts of the device from the packaging and

remove all packaging materials.

Check the package for completeness and for signs of visible

damage.

If the delivery is incomplete or damage has occurred as a

result of defective packaging or during transport, contact

the service hotline (see Warranty section).

Disposal of the packaging

The packaging protects the device from damage

during transport. The packaging materials have

been selected for their environmental friendliness

and ease of disposal and are therefore recyclable.

SPBD 5000 A1 US-EN │ 11 ■

Returning the packaging to the material cycle conserves raw

materials and reduces the amount of waste that is generated.

Dispose of packaging materials that are no longer needed in

accordance with applicable local regulations.

Charging the power bank

Before using the power bank, the integrated battery must be

fully charged.

► Due to the high battery capacity and bearing in mind the

charging time, the power bank must be charged using a

USB power adapter.

► Use only a USB power adapter with an output voltage of

5V and an output current of at least 2.1A to charge the

power bank.

► Charging takes about 3 hours.

♦ Connect the USB plug of the charger cable to suitable

USB power supply (not supplied).

♦ Connect the micro-USB plug on the charging cable to

the micro-USB charging port (IN) on the power bank.

The current charge level is shown during charging by

means of the charge level LEDs :

LED display Charge level

One LED is ﬂashing < 20%

SPBD 5000 A1

■ 12 │ US-EN

LED display Charge level

One LED is on, the second

LED is ﬂashing 20–49%

Two LEDs are on, the third

LED is ﬂashing 50–74%

Three LEDs are on, the fourth

LED is ﬂashing 75–99%

All LEDs are on 100%

Checking the charge level

You can also check the charge level of the power bank when

it is not charged or while it is being used for charging.

♦ Press the ON/OFF button brieﬂy. The charge level

LEDs show the current charge level of the power bank

for about 30 seconds.

LED display Charge level

All LEDs are on 100%

Three LEDs are on 75–99%

Two LEDs are on 50–74%

One LED is on 20–49%

One LED is ﬂashing < 20%

All LEDs oﬀ 0%

SPBD 5000 A1 US-EN │ 13 ■

Handling and use

Charging mobile devices with the power

bank

♦ Connect the micro-USB plug on the charging cable

to the micro-USB port on the mobile device and the USB

plug to the USB socket (OUT) on the power bank. The

charging process starts automatically.

♦ If charging does not start automatically, press the ON/

OFF button brieﬂy to start the charging process.

Alternatively, you can also use the original charging cable

(USB cable) provided by the respective device manufacturer.

Some devices cannot be charged due to the high start-up

charging current required (higher than 2.1 amps).

♦ During the charging process, the current Power Bank

charge level is shown via the charge level LEDs (see

table in section entitled "Checking the charge level").

♦ To stop charging, disconnect the charging cable from

the mobile device and the power bank. The charge level

LEDs switch oﬀ.

SPBD 5000 A1

■ 14 │ US-EN

Troubleshooting

The power bank does not charge

♦ Connection may be faulty. Check the connection.

A connected device will not charge

♦ The integrated battery is empty. Charge the battery.

♦ No connection to the device. Check the connection.

♦ Press the ON/OFF button brieﬂy to start the charging

process.

♦ The charging current of the connected device is too low

(< 80 mA) or too high (> 2.1 A).

If you cannot solve the problem with the above-mentioned

solutions, please contact the service hotline (see Warranty

section).

SPBD 5000 A1 US-EN │ 15 ■

Cleaning

Possible damage to the device.

► There are no serviceable parts or parts requiring cleaning

inside the power bank. Moisture can cause damage to the

device.

► To avoid irreparable damage to the device, ensure that

moisture cannot penetrates the device during cleaning.

► Do not use caustic, abrasive or solvent-based cleaning

materials. These can damage the surfaces of the device.

♦ Clean the housing of the device with a lightly moistened

cloth and a mild detergent only.

Storage when not in use

♦ Store the device in a location that is clean, dry, dust-free

and not in direct sunlight.

♦ For long-term storage, the integrated battery should be

fully charged to extend its operating life.

SPBD 5000 A1

■ 16 │ US-EN

Disposal

Electronic devices may not be thrown away as part of normal

household trash. If you can no longer use your electronic

device, dispose of it in accordance with the legal provisions

applicable in your state. This will allow you to ensure that old

electronic devices are recycled and environmental pollution is

kept to a minimum.

Additional information about disposal is available on the

Internet at www.epa.gov.

SPBD 5000 A1 US-EN │ 17 ■

Appendix

Technical data

Integrated battery

(lithium-polymer)

3.7 V / 5000 mAh / 18.5 Wh

Input 5V ,2.1A

Output 5V ,2.1A

Minimum discharge

current 80 mA

Charging time approx. 3 hours

Working temperature 41°F to 95°F

(5°C to 35°C)

Storage temperature 32°F to 113°F

(0°C to 45°C)

Relative humidity

(no condensation) 10 %–70 %

Dimensions

approx. 3.6 in x 2.4 in x 0.5in

(approx. 9.3 cm x 6.3 cm x

1.5 cm)

Weight approx. 4oz

(approx. 115g)

Page is loading ...

Silvercrest 282713 Owner's manual

Related papers

Other documents