Lucci Power 299272 Installation guide

Brand
Lucci Power
Model
299272
Type
Installation guide

Lucci Power 299272 is a wirelessly interconnected smoke alarm with lithium battery backup, capable of creating a network of up to 24 smoke alarms in a single group. To set up the interconnection, one smoke alarm needs to be designated as the master model, while all others will be slave models. To enter the configuration/pairing mode on the master model, press the test button seven times in a row, causing the orange LED to flash once per second. To connect a slave model to the master, press the test button five times in a row.

Lucci Power 299272 is a wirelessly interconnected smoke alarm with lithium battery backup, capable of creating a network of up to 24 smoke alarms in a single group. To set up the interconnection, one smoke alarm needs to be designated as the master model, while all others will be slave models. To enter the configuration/pairing mode on the master model, press the test button seven times in a row, causing the orange LED to flash once per second. To connect a slave model to the master, press the test button five times in a row.

SKU# 299272 - RF wireless smoke alarm pairing guide
THIS SMOKE ALARM MUST BE INSTALLED BY A LICENSED ELECTRICIAN
RF wirelessly interconnectable with 3V Lithium Battery Backup
RF modular is built in to SKU# 299272: Interconnections through RF wireless are available
RF wireless interconnection
Set a local wireless interconnection for smoke alarms, please read the following:
1. Set one of the smoke alarm as Master model (all others will be a Slave model): consecutive quick press the
test button 7 times, then the Orange LED will flash per second, the smoke alarm has entered into
configuration/pairing mode；
2. Consecutive quick press the test button for 5 times of any Slave model to connect to the Master model,
orange LED will light on for about 10s an and about 10s later, the slave model will give a “beep” with LED
flash two times, means Connect to the master model in a group for interconnection successfully.
3. Push the Test/Hush button and hold on for alarming testing, the interconnected smoke alarms will interact
(response) for a delay time of maximum 30s when tested.
4. Other unit please operate as step 1 to 3 above to interconnection one by one (Up to 24 pieces in a group).
NOTE: If there is no “beep” and/or the smoke alarm cannot join the group for interconnection, you may
need recovery the smoke alarm to factory set as below operation: consecutive quick press the test
button 9 times then orange LED flashes 2 times and off and re-interconnection again.
FUNCTIONAL DESCRIPTION FOR SMOKE ALARMS:
Function
Test/Hush Button
Indicator
Function exit
Select a smoke alarm to
be Master model of
interconnection--
master model
Consecutive quick
press the button for
7 times
Orange LED flashes at a frequency
1Hz (flash per second), the smoke
alarm is entered into configuration/
pairing mode
Long press the
test/Hush button or wait
above 60s, the smoke
will exit from the status
of pairing.
Select a slave smoke
alarm to join into master
model to make an
interconnection group
Consecutive quick
press the button for
5 times
Orange LED will light on for 10s, the
slave model will give a “beep” with
LED flashes two times, indicate to
join the master model for an
interconnection successfully
Long press the
test/Hush button or wait
above 60s, the smoke
will exit from the status
of pairing.
Recover to factory
setting for any smoke
alarms
Consecutive quick
press the test
button 9 times
Orange LED Flashes 2 times and
then off
---
NOTE: As 60s later the smoke alarm will exit from the status of interconnection/pairing, you may need to
re-set the master model again if more units need to add in the group. Please recover to factory setting
when you ask for a new interconnection.
  • Page 1 1

Lucci Power 299272 Installation guide

Brand
Lucci Power
Model
299272
Type
Installation guide

Lucci Power 299272 is a wirelessly interconnected smoke alarm with lithium battery backup, capable of creating a network of up to 24 smoke alarms in a single group. To set up the interconnection, one smoke alarm needs to be designated as the master model, while all others will be slave models. To enter the configuration/pairing mode on the master model, press the test button seven times in a row, causing the orange LED to flash once per second. To connect a slave model to the master, press the test button five times in a row.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Other documents