2. Laurel Designs
  3. THDGAEHBA3

Laurel Designs THDGAEHBA3 Operating instructions

  • Hello! This document provides assembly instructions for the GAEH-BA3 light fixture. It covers everything from preparing the installation to finishing it, including the wire connections and mounting. I'm ready to assist you with any questions about these instructions.
  • What should I do before starting the installation?
    How do I connect the wires?
    What is the final step of the installation?
Assembly Instructions: GAEH-BA3
IMPORTANT:
• ALL INSTALLATION WORK SHOULD BE DONE BY ACCREDITED PROFESSIONAL.
• SHUT OFF POWER SUPPLY AT FUSE OR CIRCUIT BREAKER!
• USE ONLY THE SPECIFIED BULBS. DO NOT EXCEED THE MAXIMUM WATTAGE!
PREPARING FOR INSTALLATION
Remove all of the contents from the carton. See the important
notes above. Shut off the power at the circuit breaker and
completelyremovetheoldxturefromthewall,includingtheold
mountingstrap.
Mountingstrap(B)containsseveralpairsofthreadedholes.Find
thepairofholesthatmatchesthespacingoftheholesonthe
junctionboxandyourxturebackplate.Twoofmountingscrews
(A)shouldbeattachedtomountingstrap(B).Youmayneedto
tightennuts(C)thatholdthesescrewsinplace.Pullthehouse
wiresthroughthecenterofmountingstrap(B).Placemounting
strap(B)overthejunctionboxsothatmountingscrews(A)are
horizontal,andinalignmentwiththeholelocationsonthexture
backplate(F).Securemountingstrap(B)tothejunctionbox
withmountingscrews(D)andascrewdriver.Tightenthescrews
securely.
CONNECTING THE WIRES
Attachthexture’swirestothepowersupplywiresfromthe
junctionbox.Connectblacktoblack(orsmooth);whitetowhite
(orribbed);groundtoground(greenorcopper).Twisttheends
ofthewirepairstogether,thentwistonawireconnector.Make
surealltwistsareinthesamedirection.Ifthereisnogroundwire
(greenorcopper)fromthejunctionbox,locategroundscrew(E)
onmountingstrap(B)andwrapthexturegroundwirearound
thegreengroundscrew(E).Useascrewdrivertosecureground
screw(E)ontothemountingbracket.Tuckallwiresneatlyinto
thejunctionbox.
FINISHING THE INSTALLATION
Placexturebackplate(F)overmountingscrews(A)sothatthey
protrudethroughtheholesinthefrontofthebackplate.Thread
deconuts(G)ontomountingscrews(A).Twistuntilbackplate(F)
ofthextureissnugagainstthewall.
Slideglassshades(I)oversockets(H)andsecureinplacewith
socketrings(J).
Installthebulbs(notincluded)inaccordancewiththexture’s
specications.Donotexceedtherecommendedwattage.
Your installation is now complete. Turn on the power and test the
xture.
CLEANING TIPS
Treat the xture gently! Regular cleaning will reduce the need for deep cleaning. For regular cleaning, turn off the light and wipe down the
xture with a clean lint-free cotton or microber cloth. Never spray cleaner directly onto the xture.
For Customer Service, contact
Toll Free: 800.277.0979 Ext. 0 or
Email: [email protected]
BLACK
(Hot)
WHITE
(Neutral)
GREEN
(Ground)
HOUSE WIRES
SMOOTH
(Or Black)
FIXTURE WIRES
RIBBED
(Or White)
BARE COPPER
(Or Green)
FG
H
J
I
/