Geneko GWG-30 Quick start guide

Brand
Geneko
Model
GWG-30
Category
Gateways/controllers
Type
Quick start guide

This manual is also suitable for

Geneko GWG-30 is a powerful and versatile gateway that enables remote monitoring and control of devices and systems via Ethernet, RS-232, RS-485, and GPIO interfaces. With its built-in GSM/UMTS modem, the GWG-30 provides reliable cellular connectivity, allowing for remote access and control even in areas with limited or no wired internet access.

The GWG-30 is equipped with a user-friendly web interface that makes it easy to configure and manage the device. It supports a wide range of protocols, including Modbus TCP/RTU/ASCII, DNP3, IEC 60870-5-101/104, and SNMP, enabling seamless integration with various industrial devices and systems.

Geneko GWG-30 is a powerful and versatile gateway that enables remote monitoring and control of devices and systems via Ethernet, RS-232, RS-485, and GPIO interfaces. With its built-in GSM/UMTS modem, the GWG-30 provides reliable cellular connectivity, allowing for remote access and control even in areas with limited or no wired internet access.

The GWG-30 is equipped with a user-friendly web interface that makes it easy to configure and manage the device. It supports a wide range of protocols, including Modbus TCP/RTU/ASCII, DNP3, IEC 60870-5-101/104, and SNMP, enabling seamless integration with various industrial devices and systems.

QUICK START
GWG Gateway
GUIDE
GWG-30, GWG-40
WHAT’S IN THE BOX:
1. GWG Gateway
2. Power supply cord (AC/DC adapter - optional)
3. Antenna GSM/UMTS (850/900/1800/1900/2100MHz)
PORTS & CONNECTORS
The front panel of
GWG-30 GWG Gateway
The rear panel of
GWG-30 GWG Gateway
3
RS-232
CONNECTOR
USB
CONNECTOR
RS-485
CONNECTOR
ETHERNET
CONNECTOR
GPIO
CONNECTOR
RESET BUTTON
POWER
CONNECTOR
MAIN GSM/UMTS
ANTENNA
CONNECTOR
INSERTING SIM CARD
Warning: do not insert or eject SIM card while the GWG
Gateway is powered on. Make sure to disconnect the
GWG Gateway from AC/DC adapter before inserting or
ejecting SIM card.
* Use a screwdriver to remove the cover from the back of the GWG Gateway
* UNLOCK SIM card holder
* Lift the SIM card HOLDER and put SIM card in it
* LOCK SIM card holder
* Put the cover back and use screwdriver PH1 type to tighten the screw
4
CONNECTING GWG GATEWAY
* Connect antenna to the GWG Gateway. Make sure to tighten antenna in
order not to be loose causing signal disruption.
* Plug AC/DC adapter cable into POWER CONNECTOR on the
GWG Gateway.
5
* Green POWER indicator will turn on.
* Wait approximately 52 seconds for the GWG Gateway to become fully
operational.
* Plug one side of ETHERNET CABLE to ETHERNET CONNECTOR on the
GWG Gateway.
* Plug other side of ETHERNET CABLE to Ethernet port on the computer.
RED wire - POWER (9-36VDC); BLACK wire - GROUND;
GREEN wire - GPIO output; WHITE wire - IGNITION;
All wires must be isolated
6
Add network 192.168.1.0/24 to the interface on your PC
* Optional: Ping 192.168.1.1 to check if the GWG Gateway is reachable
* Open your Web browser (e.g. Firefox, Chrome, Safari, Opera, or Internet
Explorer) and enter the following address: http://192.168.1.1
* When prompted for your login credentials, use "admin" (without quotation
marks) for both username and password.
* After logging in you should be able to see administration web page, which
allows you to easily setup the GWG Gateway.
ADMINISTRATION WEB PAGE
7
QUICK SETUP
* Once logged in to administration web page, click on SETTINGS > MOBILE
SETTINGS link from the menu on the left side of the screen.
* If SIM card is present, ENABLED check box will be checked. Otherwise, you
need to insert SIM card as explained in "Inserting SIM cards" chapter.
* Your GSM operator should provide you with PROVIDER, USERNAME
(optional), PASSWORD (optional), APN and PIN (optional) information. Make
sure you enter this into corresponding elds, and then click on SAVE button.
* Flashing red NETWORK indicator will turn on.
* After a few minutes when the GWG Gateway is connected, connection
status will be accomplished.
* Green NETWORK indicator will turn on.
* Click on SETTINGS > ETHERNET SETTINGS > LAN PORTS link from the menu
on the left side of the screen
* Set IP Address and Subnet Mask and click on SAVE button
* Add a new network to the interface on your PC
* Ping new IP address
* When the GWG Gateway is accessible, insert new IP address in a Web
browser
* Click on MAINTENANCE > DATE/TIME SETTINGS link from the menu on the
left side of the screen.
* Click on SYNC CLOCK button. The GWG Gateway will sync DATE and TIME
elds with your computer's current date and time. Now click on SAVE
button.
Ocial web site: https://www.geneko.rs
Register on web site for support.
GENEKO is the registered trademark of GENEKO Company.
© 2015 GENEKO Co. All rights reserved.
QSG GWG30-40 Rev. A Nov 15
TURN LOGGING ON
When troubleshooting GWG Gateway make sure logs are turned on and log
size is set to 512 KB or 1 MB.
You should send logs to Geneko when submitting support request.
* Click on MANAGEMENT > LOGS link from the menu on the left side of the
screen.
* Click on LOCAL SYSLOG radio button, and then click on SAVE button.
* Set appropriate log size and click on SAVE button.
* Log is now available for download from GWG Gateway to your computer
when you click on EXPORT LOG button.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8

Geneko GWG-30 Quick start guide

Brand
Geneko
Model
GWG-30
Category
Gateways/controllers
Type
Quick start guide
This manual is also suitable for

Geneko GWG-30 is a powerful and versatile gateway that enables remote monitoring and control of devices and systems via Ethernet, RS-232, RS-485, and GPIO interfaces. With its built-in GSM/UMTS modem, the GWG-30 provides reliable cellular connectivity, allowing for remote access and control even in areas with limited or no wired internet access.

The GWG-30 is equipped with a user-friendly web interface that makes it easy to configure and manage the device. It supports a wide range of protocols, including Modbus TCP/RTU/ASCII, DNP3, IEC 60870-5-101/104, and SNMP, enabling seamless integration with various industrial devices and systems.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents