Polti Lupin the 3rd Owner's manual

Brand: Polti

Model: Lupin the 3rd

Category: Coffee makers

Type: Owner's manual

LUPIN M0S10100 1S01:A5 15/06/2012 14.31 Pagina 1

11b

11c

11a

Fig.1

Fig.2

Fig.4

Fig.3

Fig.5

Fig.7

M0S10100 1S01

Fig.8

Fig.6

LUPIN M0S10100 1S01:A5 15/06/2012 14.31 Pagina 2

LUPIN THE 3

LEGEND

1) Water reservoir

2) Reservoir lid

3) Main switch

4) Auxiliary socket for cappuccino maker

5) Cream knob

6) Coffee dispenser

7) Capsule compartment

7a) Capsule compartment door

8) Supply sensor

9) Drink length adjustment knob

10) Drink length indicators

11) Collection drawer

11a) Cup resting surface

11b) Capsule collection compartment

11c) Liquid collection compartment

12) Power supply cable

This appliance conforms with Directive

2004/108/EC (EMC) and Directive

2006/95/EC (low voltage).

POLTI S.p.A, reserves the right without prior notice

to introduce technical and construction changes as

it considers necessary.

PRECAUTIONS

KEEP THESE INSTRUCTIONS

• Read these instructions for use carefully before

using the appliance. Any use which does not

comply with these instructions will invalidate the

warranty.

• The wiring system to which the appliance is con-

nected must always comply with the laws in

force.

• Before connecting the appliance, make sure that

the mains voltage is the same as the voltage in-

dicated on the data label of the appliance and

that the power outlet is connected to earth.

• Always turn off the appliance at the on/off switch

before unplugging it.

• If the appliance is left unused, disconnect it from the

mains. Never leave the appliance unattended with

the cable plugged into the mains.

• Always make sure the appliance is unplugged

before performing maintenance work of any kind.

• Do not pull the power cable out of the socket, but

grasp the plug itself to avoid damage to the

socket.

• Do not allow the power cable to be twisted,

crushed, stretched, or come into contact with

sharp or hot surfaces.

• Do not use the appliance if the power cable or

other important parts are damaged.

• Do not use electric extension leads that are not

authorized by the manufacturer, as they may

cause damage or fire.

• If it is necessary to replace the power supply ca-

ble, please refer to the nearest Polti authorised

service centre, since the use of a special tool is

necessary.

• Never touch the appliance with wet hands or feet

with the cable plugged into the mains.

• Do not use the appliance when barefoot.

• Do not use the appliance near a bathtub, shower

or container full of water.

• Never immerse the appliance, the cable or the

plugs in water or another liquid.

• Use of the appliance in places where there is a

danger of explosions is prohibited.

• Do not use the product with toxic substances.

• Do not lay the hot appliance on surfaces sensi-

tive to heat.

• Do not leave the appliance exposed to wind or

rain.

• Do not place the appliance near a live element,

an electric stove or any other source of heat.

• Do not expose the appliance to extreme temper-

atures.

• Never let children or people who are not familiar

with how the appliance works use it.

• Do not press the buttons hard or with a pointed

object such as a pen.

• Always rest the appliance on a stable surface.

• In case of accidental fall of the appliance it is

necessary to have it checked by an authorized

Service Centre as the internal safety features

may have been affected.

• In case of breakdown or malfunction switch off

the appliance and never attempt to disassemble

it, but refer to an authorized Service Centre.

• In order to avoid prejudicing the safety of the ap-

pliance, use only original spare parts and acces-

sories approved by the manufacturer.

• Do not wind the power cable around the appli-

ance, especially when the appliance is still hot.

• It is necessary to keep the appliance in horizontal

position during operation.

Read these instructions carefully before using the appliance.

english

LUPIN M0S10100 1S01:A5 15/06/2012 14.31 Pagina 8

LUPIN THE 3

ENGLISH

• Check that there is water in the reservoir before

turning on the machine.

• Always fill the water reservoir with cold clean wa-

ter. Do not use mineral water, distilled water, milk

or any other liquid.

• During refilling with water, switch off and discon-

nect the appliance from the mains.

• Do not wash coffee machine accessories in the

dishwasher.

• The presence of water in the capsules collection

drawer is normal and is due to emptying of the

circuit after making each cup.

• This appliance is not intended for use by persons

(including children) with reduced physical, sen-

sory or mental capabilities, or lack of experience

and knowledge, unless they have been given su-

pervision or instruction concerning use of the ap-

pliance by a person responsible for their safety.

• Children should be supervised to ensure that

they do not play with the appliance.

• The appliance must not be used if it has fallen,

been dropped or when it has visible signs of da-

mage or leaks.

• If the supply cord is damaged, it must be repla-

ced by the manufacturer, its service agent or si-

milarly qualified persons in order to avoid a ha-

zard.

CORRECT USE OF THE

PRODUCT

This appliance is intended to be used in household

and similar applications such as:

• Staff kitchen areas in shops, offices and other

working environments;

• Farm houses;

• By clients in hotels, motels and other residential

type environments;

• Bed and breakfast type environments.

Please read the instructions carefully and keep

them, as they could be useful to you in the future.

Polti S.p.A declines liability for any damage or

accident derived from any use of this appliance

which is not in conformity with the instructions

contained in this manual.

ATTENTION

Directive 2002/96/EC (Waste Electrical and Elec-

tronic Equipment - WEEE): information for users

This product complies with EU Directive

2002/96/EC.

The crossed-out wastebasket symbol on

the appliance means that at the end of its

useful lifespan, the product must be dis-

posed of separately from ordinary house-

hold wastes.

The user is responsible for delivering the appliance

to an appropriate collection facility at the end of its

useful lifespan. Appropriate separate collection to

permit recycling, treatment and environmentally

compatible disposal helps prevent negative impact

on the environment and human health and pro-

motes recycling of the materials making up the

product. For more information on available collec-

tion facilities, contact your local waste collection

service or the shop where you bought this appli-

ance.

THE CAPSULE SYSTEM

The machine is designed exclusively for use with

the "Aroma Polti" capsule. Each capsule contains

just the right amount and just the right grind to ob-

tain the best espresso coffee in a few seconds. The

wrapper on the capsule is made of polypropylene,

an excellent material for use in contact with food-

stuff. It is hygienic, convenient, and very resistant to

high temperatures.

The capsule system is not only very convenient and

easy to use, it guarantees all the freshness and aro-

ma of freshly roasted coffee, so that you can enjoy

your favourite blend.

Use with capsules other than "Aroma Polti"

capsules will result in forfeiture of the warranty.

SET UP - PREPARATION OF THE

MACHINE

• Carefully remove the machine and the acces-

sories from the package.

• Move the water tank slightly towards the outside

of the appliance (1) and pull upwards to remove

(fig.1).

• Open the reservoir lid (2) (fig.2) and rinse the re-

servoir (1) using clean cold water.

• Fill the reservoir (1) with clean cold water only,

put it back into the machine and close the lid.

Do not fill the reservoir with carbonated water or

any other liquid.

• Insert the power cable plug (12) into a suitable

• WARNING: the capsule is automatically pu-

shed into the compartment when the door

(7a) is closed, pushing it as far as it will go.

Never push the capsule in with your fingers.

LUPIN M0S10100 1S01:A5 15/06/2012 14.31 Pagina 9

LUPIN THE 3

earthed socket.

• Turn on the appliance by pressing the main

switch (3). During warm-up the 4 drink length in-

dicators (10) light up in sequence.

When optimal operating temperature is reached, the

supply sensor (8) remains fixed on as well as the in-

dicator (10) corresponding to the selected length.

• The height of the cup resting surface can also be

adjusted (11a) to two different positions (high or

low), depending on whether mugs or coffee cups

are being used.

To adjust the surface height lift and remove the

collection drawer (11) from the appliance (fig.3),

pull out the cup surface rest (11a) from the liquid

collection compartment (11c), as shown in fig. 4,

and replace in the most suitable position.

WARNING: The first time you use the appli-

ance, it is important to do a washing cycle us-

ing a cleaning capsule provided as described

in the "MAINTENANCE" section.

MAKING COFFEE

• Put a cup under the coffee dispenser (6).

• Ensure that the cream konb (5) on the back of

the appliance is in the open position (OPEN)

(fig.5).

When open (OPEN), the cream tap (5) exploits

the “Venturi” effect, namely the coffee is mixed

with air, making it extra creamy.

• Open the capsule compartment door (7a) and

put a capsule in the compartment (7), in the posi-

tion suggested by its shape (fig.6).

• Close the door, pushing it all the way.

• Adjust the length of the drink to be supplied by

turning the knob (9) to one of the 4 pre-set regu-

lations.

The first 3 indicator lights correspond to short, me-

dium and long coffee, the last, instead, is for drinks

like tea (fig. 7).

The choice is shown by the turning on of a length

signaller (10) positioned at the level of the cho-

sen length.

• Touch the supply sensor (8). A few moments la-

ter, the coffee will start to come out.

The supply stops automatically once the previou-

sly selected quantity has been dispensed. Sup-

ply can in any case be interrupted at any stage

by pressing the supply sensor once again (8).

• The used capsule automatically falls into the col-

lection drawer (11) when a new one is placed in

the compartment (7).

Empty the used capsules drawer frequently

to ensure that used capsules do not block the

exit passage.

NOTE: before the cleaning operation, ensure that

the empty capsule has been inserted and then

touch the supply sensor (8). If the instruction is not

followed, the water supplied is collected in the li-

quid collection compartment (11c) instead of co-

ming out from coffee dispencer (6).

PREPARATION OF DRINKS / TEA

This machine can prepare also some other drinks

and infusions with Aroma Polti Line.

• Before preparing drinks or tea, close the cream

knob (5) by rotating it to the “CLOSE” position

(fig.5).

• To supply the drink, proceed as for preparing cof-

fee.

WARNING: always ensure that the cream knob

is repositioned to “OPEN” before preparing cof-

fee again.

SHORTAGE OF WATER

Lack of water in the tank is signalled by the simulta-

neous flashing of the 4 drink length indicators (10).

Fill the tank again as described previously.

AUXILIARY SOCKET FOR

CAPPUCCINO MAKER

It is possible to connect the Cappuccì (optional) to

the coffee machine with the auxilary socket (4).

Open the auxiliary socket door with a screwdriver.

Warning: This operations must be followed with

the coffee machine not connected to the main

power. Follow then the Cappuccì instruction

manual.

• WARNING: the capsule is automatically pu-

shed into the compartment when the door

(7a) is closed, pushing it as far as it will go.

Never push the capsule in with your fingers.

english

LUPIN M0S10100 1S01:A5 15/06/2012 14.31 Pagina 10

LUPIN THE 3

ENGLISH

The new Polti milk foamer is perfect for all the per-

sons that want to foam the milk and arrange a good

cappuccino like the bar.

It is easy to use.

It is provided with a comfortable anti splash cap

and a non-stick jug for a fast heating and easy clea-

ning.

It is possible to connect Cappuccì to the main

power or directly to the “Lupin” machine.

ENERGY SAVING MODE

Approximately 10 minutes after the last use of the

appliance, it will enter “ENERGY SAVING” mode

where the device is disabled. This mode is signal-

led by the flashing of the supply sensor (8).

To reactivate the appliance normally, simply touch

the supply sensor (8).

MAINTENANCE

• Always unplug the appliance before performing

any maintenance operations.

• Clean the outside of the appliance with a damp

cloth only. Never use solvents or detergents, as

they could damage the plastic surface.

• To clean the brewing elements and to help main-

tain your Polti capsule coffeemarker, use a clean-

ing capsule at least every 2/3 days. Cleaning is

carried out in the same way as coffee is prepa-

red, by adjusting the drink length adjustment

knob (10) to that for tea (fig. 6).

RECOMMENDATION: Place a dish underneath

the outlet to collect water.

• Every time you clean the infusion parts, we re-

commend you also clean the coffee dispenser.

Unhook the cover to the coffee dispenser (6), pu-

shing the lever down as far as it will go and slip-

ping it off (fig.7). Clean the parts where the coffee

flows using a soft, damp sponge and then return

the cover to its position.

• Remove the collection drawer (11), emptying it

and clean regularly after having separated the 3

compartments (11a, 11b and 11c).

• Do not leave water in the machine’s tank during

periods of disuse.

• To keep the tank hygienically clean, rinse it daily.

To clean and maintain your Polti capsule coffee-

maker, we recommend using the Clean Espresso

cleaning kit (item code PAEU0176).

Clean Espresso cleans and protects, extending the

life of your coffeemaker thanks to two new, specifi-

cally designed formulas (decalcifying and degrea-

sing).

Clean Espresso is available at

www.aromapolti.com

If you decide to use the CLEAN ESPRESSO clea-

ning kit, we recommend repeating the action descri-

bed at point 8 of the instruction manual at least th-

ree times, in order to rinse the insides of the

machine thoroughly.

LUPIN M0S10100 1S01:A5 15/06/2012 14.31 Pagina 11

ENGLISH

LUPIN THE 3

PROBLEM CAUSE SOLUTION

All luminous indicators (10) and

the supply sensor (8) are off.

The appliance is not plugged in

The main switch (3) is off

Plug the power cable into a suit-

able power outlet

Turn on the main switch

The 4 drink length indicators flash

simultaneously and the sensor (8)

is off.

The water reservoir (1) is

empty or incorrectly inserted.

Fill the water reservoir (1).

Check that the reservoir has been

inserted correctly.

The first and last drink length indi-

cator (10) and coffee sensor (8)

flash alternatively in a clockwise

direction.

Appliance malfunction.

Turn the appliance off and on

again. If the problem persists, con-

tact an authorised service centre.

The collection drawer (11) does

not close (do not force)

The drawer is full of used

capsules

Empty the drawer and put it back

in the appliance.

The appliance appears to work

properly, but it does not dispense

coffee

No capsule in the compartment.

Empty capsule for cleaning in the

compartment.

Put the right capsule in the com-

partment and repeat the process.

The machine does not make cof-

fee the first time it is turned on or

after filling the reservoir

The reservoir has not been

inserted correctly, or the

appliance is initially unable to ob-

tain water

Insert the reservoir correctly and

make sure it has been completely

filled

Coffee dispensed at an angle or

outside the cup.

Coffee dispenser nozzle dirty

Clean as specified in the "Mainte-

nance" section

TROUBLESHOOTING

LUPIN M0S10100 1S01:A5 15/06/2012 14.31 Pagina 12

Polti Lupin the 3rd Owner's manual

Brand: Polti

Model: Lupin the 3rd

Category: Coffee makers

Type: Owner's manual

Download PDF

report

Polti Lupin the 3rd Owner's manual

Polti Lupin the 3rd Owner's manual

Related papers

Other documents