Breville BES980BKS User manual

BES980

the Oracle

®

Instruction Booklet

2

CONTENTS

3 Breville recommends safety ﬁrst

6 Know your Breville product

9 Features of your Breville product

10 Operating your Breville product

24 Coffee making tips & preparation

28 Care & cleaning

34 Troubleshooting

39 Coffees to try

3

BREVILLE RECOMMENDS SAFETY FIRST

At Breville we are very safety conscious. We design and manufacture consumer products with the

safety of you, our valued customer, foremost in mind. In addition we ask that you exercise a degree

of care when using any electrical appliance and adhere to the following precautions.

FOR ALL ELECTRICAL

APPLIANCES

• Carefully read all instructions

before operating and save for

future reference.

• Remove any packaging

material and promotional

labels or stickers before using

the Oracle

®

for the ﬁrst time.

• To eliminate a choking

hazard for young children,

remove and safely discard the

protective cover ﬁtted to the

power plug of this appliance.

• Do not place the product near

the edge of a bench or table

during operation. Ensure the

surface is level, clean and free

of water and other substances.

• Do not let the cord hang over

the edge of a bench or table,

or become knotted. Keep

away from hot gas or electric

burner, or where it could

touch a heated oven.

• This appliance can be used

by children aged from 8 years

and above if they have been

given supervision or

instruction concerning use

of the appliance in a safe way

and understand the hazards

involved. Cleaning and user

maintenance shall not be

made by children unless they

are aged from 8 years and

above and supervised. Keep

the appliance and its cord out

of reach of children aged less

than 8 years.

IMPORTANT SAFEGUARDS

4

• The installation of a residual

current device (safety switch)

is recommended to provide

additional safety protection

when using electrical

appliances. It is advisable that

a safety switch with a rated

residual operating current not

exceeding 30mA be installed

in the electrical circuit

supplying the appliance.

See your electrician for

professional advice.

SPECIFIC INSTRUCTIONS

FOR BES980 THE ORACLE

®

• This appliance is

recommended for household

use only. Do not use this

appliance for any purpose

other than its intended

use. Do not use in moving

vehicles or boats. Do not

use outdoors.

• If the appliance is to be:

- left unattended

- cleaned

- moved

- assembled; or

- stored

BREVILLE RECOMMENDS SAFETY FIRST

• Appliances can be used

by persons with reduced

physical, sensory or mental

capabilities or lack of

experience and knowledge

if they have been given

supervision or instruction

concerning use of the

appliance in a safe way and

understand the hazards

involved.

• Children shall not play with

the appliance.

• Regularly inspect the

supply cord, plug and actual

appliance for any damage. If

found damaged in any way,

immediately cease use of

the appliance and return the

entire appliance to the nearest

authorised Breville Service

Centre for examination,

replacement or repair.

• Keep the appliance

and accessories clean. Follow

the cleaning instructions

provided in this book. Any

procedure not listed in this

instruction booklet should be

performed at an authorised

Breville Service Centre.

5

BREVILLE RECOMMENDS SAFETY FIRST

Always switch Off the

espresso machine by pressing

the POWER button to Off,

switch Off at the power outlet

and unplug.

• Ensure the product is

properly assembled before

ﬁrst use.

• Do not use any other liquid

apart from cold mains/town

water. We do not recommend

the use of highly ﬁltered,

de-mineralized or distilled

water as this may affect the

taste of the coffee and how the

espresso machine is designed

to function.

• Ensure the portaﬁlter is ﬁrmly

inserted and secured into the

group head before starting

an extraction. Never remove

the portaﬁlter during the

extraction process.

SAVE THESE INSTRUCTIONS

• Do not touch hot surfaces.

Allow the product to cool

down before moving or

cleaning any parts.

• Use caution after milk

texturing as the ‘Auto Purge’

function may purge hot

steam when the steam

wand is lowered.

• Use caution when operating

machine as metal surfaces are

liable to get hot during use.

• Use caution when using the

de-scale feature as hot steam

may be released. Before

de-scaling, ensure drip tray

is empty and inserted. Refer

to page 32 for further

instructions.

6

KNOW YOUR BREVILLE PRODUCT

A. Integrated conical burr grinder

With removable 280g bean hopper.

B. Top-ﬁll 2.5L removable water tank

With integrated water ﬁlter and backlit

level indicator.

C. Grind Size dial

Select the desired espresso grind size to

suit your coffee beans.

D. Grind LCD

Displays current grind settings.

E. Main LCD

Displays current settings and simpliﬁes

programming.

F. 1 CUP and 2 CUP buttons

With preset shot durations, manual

override or reprogrammable

durations/volumes.

G. Grind outlet

With auto grind, dose & tamp function.

H. Heated 58mm group head with embedded

element

I. 58mm full stainless steel portaﬁlter

J. Drop down swivel foot

Lifts the machine upwards for

easy maneuverability.

K. Heated cup warming tray

L. HOT WATER button

Press to start and stop the ﬂow of hot water

from the hot water outlet.

M. LONG BLACK dial

With preset and customisable settings.

N. Steam lever

With one touch auto milk texturing

(down position) and manual milk texturing

(up position).

O. Steam LCD

Displays current milk temperature and

texture settings.

P. SELECT dial

Select the desired milk temperature and

texture. Also use this dial in conjunction

with the MENU button to set the

programmable functions.

Q. Cool touch steam wand

With integrated temperature sensor.

R. Dedicated hot water outlet

Delivers hot water for Long Black and pre-

heating cups.

S. Descale access point

T. Tool storage tray

Houses accessories when not in use.

U. Removable drip tray

With Empty Me! indicator.

7

KNOW YOUR BREVILLE PRODUCT

I

J

G

D

E

F

H

B

C

A

K

M

L

N

O

P

Q

S

U

T

R

8

KNOW YOUR BREVILLE PRODUCT

A

E

F

I

G

H

J

D

C

K

L

M

B

ACCESSORIES

A. Stainless steel milk jug

B. 2 cup ﬁlter basket

C. 1 cup ﬁlter basket

D. Water ﬁlter holder with ﬁlter

E. Cleaning disc

F. Mini grinds bin

G. Burr brush

H. Grind outlet brush & tamp

removal magnet

I. Cleaning tool for steam wand tip

J. Allen key

K. Steam wand cleaning powder

L. Water hardness test strip

M. Espresso cleaning tablets

9

FEATURES OF YOUR BREVILLE PRODUCT

HANDS FREE AUTOMATIC

GRIND, DOSE & TAMP

Automatically grinds, doses and tamps the

required amount of coffee, mess free.

GRIND SIZE DIAL

Adjustable grind settings from ﬁne to coarse

for optimal espresso extraction.

STAINLESS STEEL CONICAL BURRS

Maximise ground coffee surface area for a

full espresso ﬂavour.

AUTOMATIC HANDS FREE

MILK TEXTURING

Automatically textures milk to the

selected temperature and style from silky

smooth latté to creamy cappuccino. Automatic

purge removes residual milk from the steam

wand when returned to the downward position.

SIMULTANEOUS COFFEE & STEAM

Dedicated stainless steel espresso and steam

boilers for simultaneous milk texturing and

espresso extraction.

PRECISION CONTROL

Electronic PID Temperature Control

Electronic temperature control delivers

precise water temperature for optimum

espresso ﬂavour. Programmable.

Actively Heated Group Head

Commercial size 58mm group head with

embedded element for thermal stability

during extraction.

Regulated Extraction Pressure

Over pressure valve (OPV) limits maximum

pressure for optimal espresso ﬂavour.

Low Pressure Pre-Infusion

Gradually increases water pressure to gently

expand grinds for an even extraction.

Programmable.

Dual Pumps

Dedicated espresso and steam boiler pumps.

Programmable Shot Temperature

Adjust water temperature to achieve optimal

espresso ﬂavour depending on coffee origin

and degree of roast.

ADDITIONAL FEATURES

One Touch Long Black

Delivers hot water directly into the cup

after espresso extraction. Preset and

customisable settings.

Shot Clock

Displays duration of the espresso shot

being extracted.

Auto Start

Switches machine on at a speciﬁed time.

Auto Off

Switches machine off after a speciﬁed

time from 5 - 20 mins.

10

OPERATING YOUR BREVILLE PRODUCT

BEFORE FIRST USE

Machine Preparation

Remove and discard all labels and packaging

materials attached to your espresso machine.

Ensure you have removed all parts and

accessories before discarding the packaging.

Remove the water tank located at the back of

the machine by pulling down the water tank

handle. Remove the plastic bag containing the

water ﬁlter and water ﬁlter holder. Clean parts

and accessories (water tank, portaﬁlter, ﬁlter

basket, jug) using warm water and a gentle dish

washing liquid. Rinse well then dry thoroughly.

TIP

To easily manoeuvre your machine, use

the drop down swivel foot located under

the drip tray. When turned to UNLOCK,

the swivel foot drops down and lifts the

machine upwards, making it easier to

access the removable water tank or

reposition the machine to another

location.

INSTALLING THE WATER FILTER

• Remove the water ﬁlter and water ﬁlter

holder from the plastic bag.

• Soak the ﬁlter in a cup of water for

5 minutes then rinse under cold

running water.

• Wash the ﬁlter holder with cold water,

taking speciﬁc care to rinse the

stainless steel mesh.

Soak filter for 5 minutes Rinse filter & mesh

• Insert the ﬁlter into the two parts of the

ﬁlter holder.

Place filter into

filter holder

• To install the assembled filter holder into

the water tank, align the base of the ﬁlter

holder with the adapter inside the water

tank. Push down to lock into place.

• Fill the water tank with cold water before

sliding back into position at the back of the

machine and locking into place.

NOTE

DO NOT use highly ﬁltered,

demineralised or distilled water in this

machine. This may affect the taste of the

coffee and how the machine operates.

NOTE

To purchase water ﬁlters, visit

www.breville.com.au or call Breville

Customer Service Centre.

11

OPERATING YOUR BREVILLE PRODUCT

FIRST USE

1. Ensure tank is ﬁlled with cold water.

You can do this by either opening the

top-ﬁll water tank lid (push to open), or

by removing the water tank at the back

of the machine.

2. Press POWER button to turn the

machine on.

3. The main LCD will display 'Hrd3',

prompting you to set the water

hardness level. Programming this

will determine the regularity of the

'DESCALE' and 'CHANGE FILTER'

alerts.

Setting Water Hardness

• Remove the supplied water hardness

test strip from the wrapper.

• Dip the test strip into a sample

of the water you have ﬁlled the

tank with. Wait for one minute.

The water hardness setting is

indicated by the number of red

squares displayed on the test

strip eg. 3 red squares indicates

a water hardness setting of 3.

• Rotate SELECT dial to the required

setting from 'Hrd1' (softest water)

to 'Hrd5' (hardest water). Press

SELECT dial to set. Machine will

beep once to conﬁrm selection.

NOTE

If your water hardness is either 4 or 5

when tested, we strongly recommend

you change to an alternate water source.

Filtered, bottled spring or mineral water

will extend both the life of your built-in

ﬁlter and descale intervals as well as

superior taste. Please ensure to test the

water hardness of the alternative water

source you've chosen and input into the

machine accordingly. Avoid using overly

ﬁltered water, like RO water unless some

mineral content is being added back to

the ﬁnal water. Never use distilled water,

or water with no or low mineral content

as this will affect both the taste the

functioning of your machine.

4. A pumping/vibrating sound will be

heard indicating empty boilers are

being ﬁlled with water for the ﬁrst

time. The main LCD will display the

current boiler temperature and ﬂash

'HEATING'.

5. After approximately 5 minutes,

the machine will reach the default

operating temperature 93˚C and all

6 buttons will illuminate. The machine

is now in STANDBY mode, ready for

the next step, 'Flushing The Machine'.

TEMP TEXTURE

SELECTPOWER

HOT WATER LONG BLACK

12

OPERATING YOUR BREVILLE PRODUCT

Flushing The Machine

When the machine has reached

STANDBY mode:

1. Press 2 CUP button to run water

through the group head for

30 seconds.

2. Press HOT WATER button to run

water through the hot water outlet.

After 30 seconds, press HOT WATER

button again to stop the ﬂow of water.

3. Lift steam lever to the MANUAL

position to release steam through the

steam wand. After 30 seconds, lower

the steam lever to the centre OFF

position.

4. Repeat steps 1–3 twice.

5. Reﬁll water tank and empty drip tray,

if required.

MANUAL will ﬂash on LCD

The machine will not reach operating

temperature (STANDBY mode) if the steam

lever is in the MANUAL position. The steam

LCD will display 'MANUAL'. Lower the steam

lever to the centre OFF position.

Steam operation is ready when the SELECT

dial illuminates.

NOTE

You will not be able to select the

1 CUP, 2 CUP or LONG BLACK functions;

or access the cleaning cycle in the menu

options until the machine has reached

operating temperature (STANDBY mode).

The machine will beep 3 times if one of

these functions is selected.

GRINDING OPERATION

Insert bean hopper into position on top of

the machine. Turn knob to lock into place.

Fill hopper with fresh beans.

TIP

We recommend quality 100% Arabica

beans with a 'Roasted On' date stamped

on the bag, not a 'Best Before' or 'Use By'

date. Coffee beans are best consumed

between 5–20 days after the 'Roasted On'

date. Stale coffee may pour too quickly

from the portaﬁlter spouts and taste bitter

and watery.

SELECTING GRIND SIZE

There are 45 espresso grind size settings

(No. 1 – ﬁnest, No. 45 – coarsest) to enable

you to select the right grind size for your

coffee beans and achieve the perfect

espresso extraction.

To select grind size, rotate the grind size

dial counter-clockwise to increase grind

coarseness or clockwise to increase grind

ﬁneness.

We recommend you start at No. 30 and adjust

as required to control espresso ﬂow rate.

13

PAGE HEADER.....

OPERATING YOUR BREVILLE PRODUCT

SELECT YOUR FILTER BASKET

Insert the correct Filter Basket into the

Portaﬁlter for the number of coffees or strength

you are making.

Use the 1 Cup Filter Basket for making a single

cup or a weaker tasting espresso.

Use the 2 Cup Filter Basket for making 2 cups

or a stronger tasting espresso, usually for mugs

or larger cups.

AUTO GRIND DOSE & TAMP

Align portaﬁlter handle with the INSERT

position on the grind outlet. Lift to insert

portaﬁlter into the grind outlet and rotate

to the centre position.

GRIND OUTLET

GROUP HEAD

CENTRE

POSITION

GRIND OUTLET

To start the auto grind, dose & tamp function,

rotate the portaﬁlter to the right then gently

guide back to the centre position. Grinding will

commence.

When the auto grind, dose & tamp function is

complete, rotate the portaﬁlter handle to the

INSERT position and lower to remove.

ESPRESSO EXTRACTION

Align portaﬁlter handle with the INSERT

position on the group head. Lift to insert

portaﬁlter into the group head and rotate

towards the LOCK TIGHT position until

resistance is felt.

EXTRACTION GUIDE

The 1 CUP button and 2 CUP button

use duration to control espresso volume.

The duration times are preset, but can be

reprogrammed (refer to 'Programming Shot

Volume/Duration', page 17). Alternatively,

access the Advanced Features if you wish

to use volumetric controls instead of duration

to determine espresso volume (refer to 'Flow

Measurement Method (VoL)', page 23).

1 CUP BUTTON

Press 1 CUP button once to extract a single

shot of espresso at the preset duration

(25 seconds). The extraction will start using

the low pressure pre-infusion.

The machine will stop after 1 CUP duration is

reached and will return to STANDBY mode.

2 CUP BUTTON

Press 2 CUP button once to extract a

double shot of espresso at the preset duration

(30 seconds). The extraction will start using

the low pressure pre-infusion.

14

PAGE HEADER.....

OPERATING YOUR BREVILLE PRODUCT

The machine will stop after 2 CUP duration

has been extracted and will return to

STANDBY mode.

MANUAL OVERRIDE

Press and hold either the 1 CUP or

2 CUP button to commence pre-infusion.

When the required pre-infusion duration

is met, release the button to begin full

pump pressure.

Press the button again to stop the pour when

required duration has been achieved.

TEXTURING MILK

The SELECT dial is used to select milk

temperature and texture. Press the dial to

toggle between milk temperature and texture.

The ﬂashing value (either temperature or

texture triangle) can be changed by rotating

the dial.

ADJUSTING MILK TEMPERATURE

Press the SELECT dial until the milk

temperature ﬂashes. Rotate the dial to increase

or decrease milk temperature. The selected

temperature will be displayed on the steam

LCD. The ideal temperature for milk is

between 55˚C– 65˚C as indicated by the

smiley face icon.

STEAM

SELECTSELECTSELECT

TEMP TEXTURETEMP TEXTURETEMP TEXTURE

ADJUSTING MILK TEXTURE

Press the SELECT dial until the milk texture

triangle ﬂashes. Rotate dial towards 'CAPP'

for more texture or 'LATTE' for less texture.

The selected texture will be displayed on the

steam LCD.

STEAM

SELECTSELECTSELECT

TEMP TEXTURETEMP TEXTURETEMP TEXTURE

Different brands and types of milk and milk

alternatives will texture differently. You may

need to adjust the texture level accordingly.

NOTE

Prior to texturing milk, always purge

steam wand by momentarily pressing

down the steam lever.

AUTO MILK TEXTURING

Start with fresh cold milk. Fill milk jug to below

the spout position. Lift steam wand and insert

into milk jug. Lower steam wand, ensuring it is

fully down. The milk jug should rest on the drip

tray and milk should cover the steam wand

seal.

MIN

MAX

15

PAGE HEADER.....

OPERATING YOUR BREVILLE PRODUCT

MILK MUST

COVER THIS

SEAL

To start, press down and release steam

lever. The LCD will display the temperature

of the milk as it heats. Milk texturing will

stop automatically when the selected milk

temperature is reached. Lift steam wand

to remove milk jug. Wipe the wand and tip

with a damp cloth. Lower steam wand to

the down position and the wand will

automatically purge.

MANUAL MILK TEXTURING

Auto milk texturing and auto shut-off are

disabled during manual milk texturing mode.

Insert steam wand into milk jug. Lift steam

lever to activate manual steam mode. Once

the desired milk texture and temperature

are achieved, lower the steam lever to the

centre OFF position. Wipe the wand and

tip with a damp cloth. Lower steam wand

to the down position and the wand will

automatically purge.

CAUTION: BURN HAZARD

Pressurised steam can still be released,

even after machine has been switched off.

Children must always be supervised.

NOTE

If machine is run continuously for

30 minutes, allow machine to cool for

5 minutes before each use.

PRESET LONG BLACK

There are 3 preset Long Black settings – small,

medium and large. To use one of these settings:

1. Insert the 2 Cup Filter Basket into the

Portaﬁlter.

2. Fill the portaﬁlter using the auto grind,

dose & tamp function.

3. Insert the portaﬁlter into the

group head.

4. Position your cup so the portaﬁlter

spouts and hot water outlet are

directed inside the cup.

5. Rotate the LONG BLACK dial to the

desired cup size.

PRESET CUP SIZE AMOUNT BREWED

Small Approx. 180ml

Medium Approx. 240ml

Large Approx. 355ml

The brewed amounts are approximate

only. Actual amounts may vary due to the

coffee bean roast, blend and freshness as well

as the selected grind size. These factors affect

extraction rate and shot volume.

6. To start extraction, press the

LONG BLACK dial. Espresso will

extract from the portaﬁlter spouts,

followed by hot water from the hot

water outlet.

16

PAGE HEADER.....

TIP

You can conduct a manual Long Black

extraction each time, or program this

as a custom setting. Once programmed,

your custom setting will appear after the

3 preset settings. Refer to 'long Black

Adjust - Programming Custom Settings’,

page 20.

HOT WATER

The HOT WATER button can be used to

pre-heat cups or add hot water manually.

To stop and start the pour of hot water, press

the HOT WATER button.

To ensure water is dispensed at the correct

temperature, hot water will cease to dispense

after approx. 30 seconds. Depending on the

size of your cup, you may need to press the

HOT WATER button a second time.

HOT WATER

NOTE

You cannot run hot water and extract

espresso at the same time.

OPERATING YOUR BREVILLE PRODUCT

NOTE

To override the setting during operation,

press the LONG BLACK dial. Pressing the

LONG BLACK dial during the espresso

extraction will stop the ﬂow of espresso

and start the ﬂow of hot water. Pressing

the LONG BLACK dial during the hot

water delivery will stop the ﬂow of hot

water.

TIP

If the preset Long Black settings do not

suit your cup size or strength preferences,

there are 6 custom Long Black settings for

you to program. Once programmed, your

custom setting will appear after the

3 preset settings. Refer to 'Long Black

Adjust - Programming Custom Settings’,

page 20.

MANUAL LONG BLACK

This allows you total control over the

Long Black process: pre-infusion duration,

espresso volume and hot water volume.

During manual Long Black mode, the LCD

will show a moving cup icon.

Press and hold LONG BLACK dial to

activate pre-infusion. Release LONG BLACK

dial to commence espresso pour.

Press the LONG BLACK dial to stop

espresso pour and commence hot water pour.

Press the LONG BLACK dial again to stop

the pour of hot water.

17

PAGE HEADER.....

OPERATING YOUR BREVILLE PRODUCT

PROGRAMMABLE FUNCTIONS

To enter program mode, press the

MENU button. Rotate SELECT dial

to the desired function.

Program mode allows you to program:

• Shot Volume

• Shot Temperature

• Clean Cycle

• Set Clock

• Auto Start

• Auto Off

• Tamp Set

• Pre-Infusion

• Long Black Adjust

To exit program mode, press MENU button.

MENU

EXIT

NOTE

The MENU button is disabled when the

machine is in coffee making mode or

dispensing hot water.

PROGRAMMING SHOT

VOLUME/DURATION

Fill the portaﬁlter using the auto grind, dose

& tamp function. Insert the portaﬁlter into the

group head.

While 'SHOT VOL' is displayed on the

LCD, rotate the SELECT dial to '1 CUP' to

reprogram the 1 CUP button, or '2 CUP'

to reprogram the 2 CUP button. Press the

SELECT dial to start espresso extraction.

When required espresso volume/duration has

been extracted, press SELECT dial to stop

extraction. Machine will beep once to conﬁrm

the new volume/duration.

SELECTSELECTSELECT

TEMP TEXTURETEMP TEXTURETEMP TEXTURE

NOTE

The 1 CUP and 2 CUP buttons use duration

to control espresso volume. Access the

Advanced Features if you wish to use

volumetric controls instead of duration to

determine espresso volume. Refer to 'Flow

Measurement Method (VoL)', page 23.

18

PAGE HEADER.....

OPERATING YOUR BREVILLE PRODUCT

SHOT TEMPERATURE

While 'SHOT TEMP' is displayed on the

LCD, press the SELECT dial. The current

temperature will ﬂash. Turn the SELECT dial

to required temperature then press SELECT

dial to set. Machine will beep once to conﬁrm

new temperature.

SELECTSELECTSELECT

TEMP TEXTURETEMP TEXTURETEMP TEXTURE

CLEANING CYCLE

The cleaning cycle cleans the shower screen

and back-ﬂushes the group head. Select this

feature when the LCD displays 'CLEAN ME!'

SELECTSELECTSELECT

TEMP TEXTURETEMP TEXTURETEMP TEXTURE

SET CLOCK

Setting the clock is optional. While 'SET

CLOCK' is displayed on the LCD, press the

SELECT dial. The current time will ﬂash or

default to 12.00AM if the time has not been

set. Turn the SELECT dial to the left or right

to adjust time. Turning the SELECT dial faster

or slower will change the rate of adjustment.

When required time has been reached, press

the SELECT dial to set. Machine will beep

once to conﬁrm the clock has been set.

SELECTSELECTSELECT

TEMP TEXTURETEMP TEXTURETEMP TEXTURE

AUTO START

Auto Start is optional. It allows you to

program the speciﬁc time when the machine

will automatically turn on. By programming

your machine, you will not have to wait for it

to pre-heat. We recommend programming the

machine to start 30 minutes before you plan

to use it.

NOTE

The clock must be set before the Auto

Start time can be programmed. If you try

to turn Auto Start on without ﬁrst setting

the clock, the machine will beep 3 times.

19

PAGE HEADER.....

OPERATING YOUR BREVILLE PRODUCT

While 'AUTO START' is displayed on the

LCD, press the SELECT dial. Turn the

SELECT dial to 'On' or 'Off'. Press SELECT

dial to set.

SELECTSELECTSELECT

TEMP TEXTURETEMP TEXTURETEMP TEXTURE

SELECTSELECTSELECT

TEMP TEXTURETEMP TEXTURETEMP TEXTURE

Turn the SELECT dial to the left or right to

select the desired Auto Start time. Turning the

SELECT dial faster or slower will change the

rate of adjustment. When the required time

has been reached, press the SELECT dial to

set. A small clock icon will be displayed on

the LCD when the Auto Start function has

been programmed.

AUTO OFF

This function sets how long the machine

will stay turned on before it automatically

turns off. It can be set for 5 mins, 10mins

or 20mins until Auto Off activates.

While 'AUTO OFF' is displayed on the

LCD, press the SELECT dial. Turn the

SELECT dial to the desired time then press

SELECT dial to set. Machine will beep once

to conﬁrm selection.

SELECTSELECTSELECT

TEMP TEXTURETEMP TEXTURETEMP TEXTURE

SELECTSELECTSELECT

TEMP TEXTURETEMP TEXTURETEMP TEXTURE

TAMP SET

This function is for advanced use only.

Adjusting tamp parameters allows for ﬁne

tuning of coffee tamping force and polishing

duration. While 'TAMP SET' is displayed on

the LCD, press the SELECT dial. The tamp

force setting will ﬂash. Turn SELECT dial to

setting 1–9.

SELECTSELECTSELECT

TEMP TEXTURETEMP TEXTURETEMP TEXTURE

SELECTSELECTSELECT

TEMP TEXTURETEMP TEXTURETEMP TEXTURE

Press SELECT dial to set and the current

polishing time will ﬂash. Turn SELECT dial to

select 2–10 seconds. Press SELECT dial to set.

Machine will beep once to conﬁrm settings.

20

PAGE HEADER.....

OPERATING YOUR BREVILLE PRODUCT

LONG BLACK ADJUST -

PROGRAMMING CUSTOM SETTINGS

There are 6 custom Long Black settings

for you to program to suit your cup size

and strength preferences. To program your

custom setting:

1. Fill the portaﬁlter using the auto grind,

dose & tamp function.

2. Insert the portaﬁlter into the group

head.

3. Position your cup so the portaﬁlter

spouts and hot water outlet are

directed inside the cup.

4. Press the MENU button. Rotate the

SELECT dial to ‘LONG BLACK ADJUST’

then press the SELECT dial.

5. Rotate the SELECT dial to the custom

setting you’d like to program - ‘Set 1’ to

‘Set 6’. Settings that have already been

programmed will display a cup icon.

NOT PROGRAMMED

PROGRAMMED

SELECTSELECTSELECT

TEMP TEXTURETEMP TEXTURETEMP TEXTURE

SELECTSELECTSELECT

TEMP TEXTURETEMP TEXTURETEMP TEXTURE

PRE-INFUSION

This function is for advanced use only.

Low pressure pre-infusion allows you to

control the pressure and duration of the

pre-infusion phase of the espresso extraction.

While 'PRE INFUSE' is displayed on the

LCD, press the SELECT dial. The pump

power setting will ﬂash. Turn SELECT dial

to increase or decrease the pre-infusion

pressure. Press SELECT dial to set and

pre-infusion duration will ﬂash. Turn SELECT

dial to adjust seconds. Press SELECT dial

to set. Machine will beep once to conﬁrm

settings.

SELECTSELECTSELECT

TEMP TEXTURETEMP TEXTURETEMP TEXTURE

SELECTSELECTSELECT

TEMP TEXTURETEMP TEXTURETEMP TEXTURE

Page is loading ...

Breville BES980BKS User manual

This manual is also suitable for

Breville BES980BKS User manual

Related papers

Other documents