ViSAGE VIS122 User manual

ViSAGE
Brand
ViSAGE
Model
VIS122
Category
Stroboscopes & disco lights
Type
User manual
MINI-BEAMWASH Page 1
MINI-BEAMWASH
(VIS122)
GB - INSTRUCTION MANUAL
MINI-BEAMWASH Page 2
Thank you for having chosen our VISAGE LED EFFECT. For your own safety, please read this user manual carefully
before installing the device.
SAFETY INTRODUCTION
• If the device has been exposed to temperature changes due to environmental changes, do not switch it on
immediately. The arising condensation could damage the device. Leave the device switched off until it has reached
room temperature.
• It is essential that the device is earthed. A qualified person must carry out the electric connection.
• Make sure that the available voltage is not higher than stated at the end of this manual.
• Make sure the power cord is never crimped or damaged. If it is damaged, ask your dealer or authorized agent to
replace the power cord.
• Always disconnect from the mains, when the device is not in use or before cleaning it. Only handle the power cord
by plug. Never pull out the plug by tugging the power cord.
• DISCONNECT DEVICE: Where the MAINS plug or an appliance coupler is used as the disconnect device, the
disconnect device shall remain readily operable.
• Shields, lenses or ultraviolet screens shall be changed if they have become visibly damaged to such an extent that
their effectiveness is impaired, for example by cracks or deep scratches.
• The lamp shall be changed if it has become damaged or thermally deformed
CAUTION:
1. Be very careful during installation. Since you will be working with a dangerous voltage you can suffer a life-
threatening electric shock when touching live wired.
2. Never look directly into the light source, as sensitive persons may suffer an epileptic shock.
3. Please be aware that damages caused by manual modifications to the device are not subject to warranty. Keep
away from children and non-professionals.
4. The light doesn’t include any spare parts for repair, please check if all the parts are well installed and screws are
fitted tightly before operating. Do not use the light when the cover is open.
GENERAL GUIDELINES
• This device is only allowed to be operated with an alternating current of max. 100-240VAC/50-60Hz and was
designed for indoor use only.
• Do not shake the device. Avoid brute force when installing or operating it.
• When choosing the installation spot, please make sure that the device is not exposed to extreme heat, moisture
or dust. The minimum distance between light-output from the projector and the illuminated surface must be more
than 1 meter. Keep a distance to any flammable objects of at least 5m.
• Operate the device only after having familiarized yourself with its functions. Do not permit operation by person not
qualified for operating the device. Most damages are the result of unprofessional operation.
• Please use the original packaging if the device is to be transported.
• For safety reasons, please be aware that all modifications on the device are forbidden. Furthermore, any other
operation may lead to short-circuit, burns, electric shock, lamp explosion, crash, etc. If this device will be operated
in any way different to the one described in this manual, the product may suffer damages and the guarantee
becomes void.
GB
MINI-BEAMWASH Page 3
MOUNTING Orientation
This fixture may be mounted in any position, provided there is adequate room for ventilation It
is important never to obstruct the fan or vents pathway.
When selecting installation location, take into consideration lamp replacement access and routine maintenance.
Safety cables must always be used.
Never mount in places where the fixture will be exposed to rain, high humidity, extreme temperature changes or
restricted ventilation.
If the external flexible cable or cord of this luminaire is damaged, it shall be exclusively replaced by the manufacturer
or his service agent or a similar qualified person in order to avoid a hazard.
Make sure the installation position is stable before you fix the light. When the light is reverse hanging, make sure the
light will not fall from the truss, use the safety cable go through the truss and bracket of the light as a supporting, to
avoid the light to fall down. There is no entrance to the work area during mounting. Periodically check if the safety
cable has fretted away or clamp is loosened. We will not take any responsibility for damages caused by a badly
installed unit.
Power Supply and Signal Cable Connection
1. Mains Power connection
The exclusive plug should be used between the connection of unit and power. Please ensure that the rated voltage
and frequency are accordance with the power supply. The required input voltage and frequency are: 100-240Vac –
50-60Hz
We suggest that every light has an independent switch so that you can turn on or turn off the light randomly. Note:
the ground wire (yellow/green double-colour wire) must be safely connected, the electrical installation must be in
accordance with the related standards
CAUTION: When installing the device, make sure there is no highly inflammable material within a distance of min.5m!
2. Connection of Signal Cable
You can use the 3-pin XLR cable to connect the output socket of the master and the input socket of the slave light.
Connect the DIGITAL OUT socket of the master and the IN socket of the slave light, then, connect the OUT socket
to the IN socket of the next light. Ordinal to connect all the lights as below:
The connection between the output of master and input of product, it’s available to use the 3 pins XLR cable which
provided by the manufacturer. Signal cable from the DMX output of the controller to the input of the first master light,
and connect to the DMX input of second slave light from the DMX output of the first master light, analogously, till
connected all the slave lights, and insert the last connector to the output of the final light. (Notice: the diameter of
core of every cable should be 0.5mm at least, double core shelter cable should be used).The signal connecting must
use the attached 3 pins XLR cable. Notice, all the internal lead wire of the 3 pins XLR cable should not touch to each
other or connect to the connector.
A DMX signal terminator is recommended on the last unit of the chain. DMX terminator is a XLR connector with a
120Ω resistor between the pin 2 and pin 3 of the XLR connector
IN
OUT
IN
OUT
OUT
IN
3
1
2
MINI-BEAMWASH Page 4
DESCRIPTION MENU
To select any functions, press the MENU button until the required function is showing on the display. Select the
unction by pressing the ENTER button and the display will blink. Use the DOWN and UP button to change the mode.
Once the required mode has been selected, press the ENTER button to setup to go back to the functions without any
changes press the MENU button again. Hold and press the MENU button for one second or wait for one minute to
exit the menu mode.
The main functions are shown below:
1 ADDR
= A001---A512
2 CHND
.=CH15
.=CH21
3 SLND
.=Master
.=Slave
4 SHND
.=Sound
.=sp0-sp9
5 SOUN
.=OFF
.=ON
6 SENS
.=0
.=100
7 BLND
.=YES
.=NO
8 LED
.=OFF
.=ON
9 DISP
.=YES
.=NO
10 PAN
.=YES
.=NO
11 TIL
.=YES
.=NO
12 MANU
= PAN
= TILT
= RED 1
= GREEN 1
= BLUE 1
= WHITE 1
= RED 2
MINI-BEAMWASH Page 5
= GREEN 2
= BLUE 2
= WHITE 2
= DIMMER
= STROBE
13 TEST
.
14 HOUR
.= 0----9999
15 VER
= V104
16 RSET
.=YES
.=NO
DMX 512 ADDRESS
To select Addr, press the ENTER button to show the DMX ADDRESS on the display. Use the DOWN/UP button
to adjust the address from 1 to 512. Once the address has been selected, press the ENTER button to setup, to
go back to the functions without any changes press the MENU button again. Hold and press the MENU button
for one second or wait for one minute to exit the menu mode.
CHANNEL MODE
To select Chnd, press the ENTER button to show the DMX CHANNEL MODE on the display.
Use the DOWN/UP button to select the, 15/21channel modes. Once the mode has been selected, press the ENTER
button to setup, to go back to the functions without any changes press the MENU button again. Hold and press the
MENU button for one second or wait for one minute to exit the menu mode.
SLAVE MODE
To select Slnd, press the ENTER button to show the SLAVE MODE on the display. Use the DOWN/UP button
to select Mast (MASTER),Sl (SLAVE ) modes. Once the mode has been selected, press the ENTER button to
setup, to go back to the functions without any changes press the MENU button again. Hold and press the
MENU button for one second or wait for one minute to exit the menu mode.
MINI-BEAMWASH Page 6
SHOW MODE
To select the Shnd , press the ENTER button to show the SHOW MODE on the display. Use the
DOWN/UP button to select speed of the auto mode . Sp 0 (slow speed), Sp 1 (speed 1) or … or S p 9 (high speed).
Once the mode has been selected, press the ENTER button to setup, to go back to the functions without any
changes press the MENU button again. Hold and press the MENU button for one second or wait for one minute to
exit the menu mode.
You can also select the Sound mode
SOUND MODE
To select Soun, press the ENTER button to show the SOUND MODE on the display. Use the DOWN/UP button
to select On (sound on) or Off (sound off) mode. Once the mode has been selected, press the ENTER button to
setup, to go back to the functions without any changes press the MENU button again. Hold and press the MENU
button for one second or wait for one minute to exit the menu mode.
SENS (SOUND SENSE MODE )
0 is for off, 100 is for the strongest of sense.
BLACKOUT MODE
To select Blnd, press the ENTER button to show the BALCKOUT MODE on the display. Use the DOWN/UP
button to select Yes (blackout) or No (normal) mode. Once the mode has been selected, press the ENTER button
to setup, to go back to the functions without any changes press the MENU button again. Hold and press the
MENU button for one second or wait for one minute to exit the menu mode.
LED DISPLAY ( to switch off the display during use )
To select Led, press the ENTER button to show the LED DISPLAY on the display. Use the DOWN/UP button to
select the On (LED on) or Off (LED off) mode. Once the mode has been selected, press the ENTER button to
setup, to go back to the functions without any changes press the MENU button again. Hold and press the MENU
button for one second or wait for one minute to exit the menu mode.
DISPLAY INVERSE
To select Disp, press the ENTER button to show the DISPLAY on the display. Use the DOWN/UP button to
select No (normal) or Yes (inversion), press ENTER button to setup. Back to the functions without any
change press MENU button.
MINI-BEAMWASH Page 7
PAN INVERSE
To select Pan, Press the ENTER button to show the PAN INVERSE on the display. Use the DOWN/UP button to
select the Yes (PAN inversion) or No (normal) mode. Once the mode has been selected, press the ENTER button
to setup, to go back to the functions without any changes press the MENU button again. Hold and press the MENU
button for one second or wait for one minute to exit the menu mode.
TILT INVERSE
To select Til, Press the ENTER button to show the TIL INVERSE on the display. Use the DOWN/UP button to select
the Yes (tilt inversion) or No (normal) mode. Once the mode has been selected, press the ENTER button to setup,
to go back to the functions without any changes press the MENU button again. Hold and press the MENU button
for one second or wait for one minute to exit the menu mode.
AUTO TEST
To select Test, press the ENTER button to show the TEST on the display and the unit will run a self‐test. To go
back to the functions without any changes press the MENU button again. Hold and press the MENU button for one
second or wait for one minute to exit the menu mode.
FIXTURE HOURS
To select Fhrs, press the ENTER button to show the FIXTURE HOURS on the display and the display will show
the number of working hours of the unit. To go back to the functions without any changes press the MENU button
again.
Hold and press the MENU button for one second or wait for one minute to exit the menu mode.
SOFTWARE VERSION
To select Ver, press the ENTER button to show the SOFTWARE VERSION on the display and the display will show
the version of software of the unit. To go back to the functions without any changes press the MENU button again.
Hold and press the MENU button for one second or wait for one minute to exit the menu mode.
RESET
To select rSet, press the ENTER button to show the RESET on the display. Press the ENTER button and all
channels of the unit will return to their standard position.
MINI-BEAMWASH Page 8
OPERATING
MASTER SLAVE OPERATING
By linking the units in master/slave connection, the first unit will control the other units to give an automatic, sound
activated, synchronized light show. This function is good when you want an instant show. You have to set the first
unit in master mode M a s t and select S p 0 (random show), Sp1 (show 1) or …or S p 9 (show 9). It’s DMX
input jack will have nothing plugged into it, and its master LED will be constantly on and sound LED will flash to
the music. The other units will have to select Sl1 (normal) or Sl2 (2 light show) mode, Their DMX cables plugged
into the DMX input jacks (daisy chain) and the slave LED lights will be constantly on.
SOUND OPERATING
- Set fixture as " MAST"
- Set "SHND" as "Sp 0"
- Set "SOUD" as "ON"
- Set ”SENS“ as " 50-60" ( if you make "0", sound control model is switched off )
- Set "BLND" as " ON"
DMX OPERATING
Using a universal DMX controller to control the units, you have to set DMX address from 1 to 512 channel so that
the units can receive DMX signal.
Press the MENU button up to when the Addr is showing on the display. Press ENTER button and the display will
blink. Use DOWN and UP button to change the DMX512 address. Once the address has been selected, press and
keep ENTER button pressed up to when the display stops blinking or storing automatically 7 seconds later. To go
back to the functions without any change press the MENU button again.
MINI-BEAMWASH Page 9
DMX TABLE
15 DMX channels
Channel
DMX Value
Function
1
0—255
Pan
2
0—255
Tilt
3
0----7
No Function
8—131
Tilt forward rotation(From slow to fast)
132---255
Tilt reverse rotation(From slow to fast)
4
0—255
Pan / Tilt Motor Speed
5
0—255
Master Dimmer (0-----100%)
6
0---255
Strobe Speed
7
0—255
Red Dimmer (0-----100%) Both Sides
8
0—255
Green Dimmer (0-----100%) Both Sides
9
0—255
Blue Dimmer (0-----100%) Both Sides
10
0---15
White Dimmer (0-----100%) Both Sides
11
0---15
No Function
16---255
Motor Auto Run
12
0---255
Motor Auto Run Speed
13
0---7
No Function
8---255
Colour Macro’s
14
0---255
Motor Run Speed
15
0---249
No Function
250---255
Reset
MINI-BEAMWASH Page 10
21 DMX channels
Channel
DMX Value
Function
1
0---255
Pan
2
0---255
Pan Fine
3
0---255
Tilt
4
0—255
Tilt Fine
5
0----7
No Function
8—131
Tilt forward rotation(From slow to fast)
132---255
Tilt reverse rotation(From slow to fast)
6
0---255
Pan / Tilt Motor Speed
7
0—255
Master Dimmer (0-----100%)
8
0---255
Strobe Speed
9
0---255
Red1 Dimmer (0-----100%)
10
0---255
Green1 Dimmer (0-----100%)
11
0---255
Blue1 Dimmer (0-----100%)
12
0---255
White1 Dimmer (0-----100%)
13
0---255
Red 2 Dimmer (0-----100%)
14
0---255
Green 2 Dimmer (0-----100%)
15
0---255
Blue 2 Dimmer (0-----100%)
16
0---255
White 2 Dimmer (0-----100%)
17
0---15
No Function
16---255
18
0---255
19
0---7
8---255
20
0---255
21
0---249
No Function
250---255
Reset
The following points have to be considered during the inspection:
All screws for installing the devices or parts of the device have to be tightly connected and must not be corroded.
MINI-BEAMWASH Page 11
There must not be any deformations on the housing, glass pane, fixations and installation spots.
The electric power supply cables must not show any damage, material fatigue or sediments. Further instructions
depending on the installation spot and usage have to be adhered to by a skilled installer and any safety problems
have to be removed.
We recommend a frequent cleaning of the device. Please use a moist, lint-free cloth. Never use alcohol or solvents.
CAUTION: Disconnect from mains before starting maintenance operation!
Cleaning and Using Frequency of Product
Please make sure that the light is power off before dismantling or maintaining, it’s very important to keep the light
clean. Frequent cleaning will ensure maximum brightness output, but also prolong the life time. It’s suggested to use
the high quality, professional glass detergent and soft cloth to clean the light. It’s not allowed to use alcohol or
chemical solvent. The inner part of the light should be cleaned by vacuum cleaner at least once a year.
When the light doesn’t work, please check if the fuse is burnt out or not. If it is, the same fuse should be replaced,
find out the faulty and restart the light. But please note the repair must be handled by professional.
TECHNICAL SPECIFICATIONS
Channels: .......................................................................................... 15/21 DMX Channels
Control mode: .................................................. Sound activated, Auto, Master / Slave, DMX
Wash face LED power: ............................................... 4 x 10W RGBW LEDs (4 in 1 ) LEDs
Wash angle: ..................................................................................................................... 25°
Beam face LED power: .......................................... 12W RGBW LEDs (4 in 1 ) CREE LEDs
Beam angle: ...................................................................................................................... 3°
Working environment: ........................................................................ indoor, 20°C – 40°C
Voltage: .................................................................................................. AC 100-240V
±10% Frequency: .................................................................................................. 50-60Hz
Power: .......................................................................................................................... 70W
Dimensions: ............................................................................................ 325X250X270mm
N.W ........................................................................................................................... 2.5Kg
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11

ViSAGE VIS122 User manual

ViSAGE
Brand
ViSAGE
Model
VIS122
Category
Stroboscopes & disco lights
Type
User manual
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Other documents