Kathrein EXIP 414 User manual

Page is loading ...

1 / 9

EXIP 414/E 20510103

SAT>IP server

Characteristics



Supports SAT>IP protocol



Conforms to SAT>IP standard as per

EN 50585



Streams DVB-S-/S2 (HDTV) signals in

an IP data stream



Can be fed into different network types:

LAN (also K-LAN, Powerline ...), WLAN

integration via router, e.g. FRITZ!Box



Four independent tuners, each for one

data stream



Web interface for conguration,

administration and import

of software updates



Status display via LED



Can be congured for different clients

1)

:

Tablet PCs, smartphones, notebooks,

SAT>IP- capable receivers (z. B. UFS

924)



On/off switch



Can be operated on different types of

LNBs, multi-switches and single-cable

multi-switches



Supports standard switching signals:

14/18 V, 22 kHz, DiSEqC™1.0,

single-cable as per EN 50494



Four Sat inputs; one Ethernet-

RJ 45 connection



For horizontal installation

(e.g. like receivers) or on-wall installati-

on with the supplied mounting bracket



For indoor installation



High-efciency plug-in power supply

for voltage supply



Cable shoe for earthing connection



Support for wall mounting



Instruction sheet

1)

Provided the required software/apps are installed on the device

Delivery scope

Vous trouverez la

version française du

document sur:

Una versione italiana

di questo documen-

to è reperibile su:

Encontrará la version

española de este docu-

mento en la página:

www.kathrein.com

(Certied by SES ASTRA)

2 / 9

• The equipment described is designed solely for the installation of satellite

receiver systems. Any other use, or failure to comply with these instructions,

will result in voiding of warranty cover.

• The equipment may only be installed in dry areas indoors. Do not install on

or against highly combustible materials.

• The power supply unit is only authorised for on-wall

mounting!

• The equipment must be provided with an earthing wire

(Cu, at least 4 mm

2

).

• Unused F-type connectors must be terminated with an EMK 05 (voltage-

separated).

• The safety regulations set out in the current EN 60728-11 and EN 60065

standards must be complied with.

• Connectors for coaxial cable: RF plugs 75Ω (series F) to

EN 61169-24.

Electrically live unit

• Do not open the unit or tamper with it!

• When working on the system always unplug the mains plug from the wall

socket!

• There must be free circulation of air to dissipate the heat from the unit. Risk

of overheating! Clearance all round must be at least 5 cm!

• Ambient temperature range: 0 to +40°C

Important:

• Do not place liquid-lled items on top of the device or power supply unit.

• The device or power supply unit must not be exposed to dripping or splash-

ing water.

• The mains plug must be easily accessible and operable.

• The only reliable method of disconnecting the unit from the mains is to un-

plug it.

Installation and safety instructions

• An inner cable conduc-An inner cable conduc-

tor diameter greater than

1.2 mm, or the presence

of burrs may damage the

product inputs/outputs be-

yond repair

Max. 2 mm

excess

length

Clamping torque

max. 3.4 Nm (danger

of overwinding)

Diameter

0.6-1.2 mm

free of burrs

3 / 9

Wall mounting

• For wall mounting only use the sup-For wall mounting only use the sup-

plied bracket (screws are not in-

cluded in the delivery scope)

Mount wall support with two screws

(Ø 4 mm, head diameter > 7 mm)

• Screw on/attach all cables

• Insert the device from above with feet

pointing down into the wall support

• Table mounting (no fastening required)

A B

(Note on mounting position A: to prevent the

device from being pushed out of the sup-

port, the device should be held during sub-

sequent cable installation work)

4 / 9

On upper part of the housing:

1. Stream LED

2. Power LED

Rear panel:

3. RF1 input V low in Quatro mode;

single-cable (EN 50494) connection

4. RF2 input V high in Quatro mode

5. RF3 input H low in Quatro mode

6. RF4 input H high in Quatro mode

7. 10/100/1000 MBit Ethernet

8. Reset button

9. On/off switch

10. Power supply connection (12 V/3 A)

Rear panel

Start-up

Proceed as follows for start-up of the EXIP 414:

1. Connection of RF inputs:

• On a Quad LNB or multi-switch: You can connect the four input cables as desired. The

device is precongured for this.

• On a Quatro LNB, splitter or tap:

You must connect the four input cables correctly according to the voltage assignment (Tab

2). On the Web interface, “Quatro” must be set under “LNB settings”.

• On a single-cable multi-switch/single-cable LNB:

Only the RF1 connection must be connected to a multi-switch or LNB. On the Web inter-Only the RF1 connection must be connected to a multi-switch or LNB. On the Web inter-

face, “OneCable” and the available UB slots must be selected under LNB settings.

1

2

3 4 5 6 7 8

9 10

5 / 9

Overview LED

Tab 1 LED ... Status EXIP 414

“Power” LED

Lit green Operation

Off No voltage supply

“Stream” LED

Lit blue Network connection generated

Flashes blue Active streaming (data transfer)

Off Network not connected

RF connections

Tab 2

Single-cable (EN 50494)

Quatro Quad/DiSEqC™

RF1 (950-2,150 MHz) 14/18 V; 0/22 kHz 14 V; 0 kHz 14/18 V; 0/22 kHz

RF2 (950-2,150 MHz) 14 V; 22 kHz 14/18 V; 0/22 kHz

RF3 (950-2,150 MHz) 18 V; 0 kHz 14/18 V; 0/22 kHz

RF4 (950-2,150 MHz) 18 V; 22 kHz 14/18 V; 0/22 kHz

2

. Network connection:

The LAN connection must be connected to the home network. Normal-

ly, the existing router (e.g. FRITZ!Box) will automatically assign an IP address.

On the Web interface, “Automatic” (default) will be set under “IP settings”.

3. “DC” connection:

Finally, the power supply is to be connected to the server rst and then to the network volt-

age.

Use Specication

Ethernet Connection to the network 10/100/1,000 MBit

DC socket Connection of power supply unit 12 V/3 A

If switch/button is ... the following occurs ...

Reset held down for about

5 seconds

Reset to factory

setting

On/Off pressed Device is cut off from voltage

supply

Additional connections

Switch and button

6 / 9

“Automatic” is set in the basic settings. This means that when the server is connected to a

router it is automatically allocated a new IP adress.

The respective client (PC, App oder IP-Receiver) detects the server via UPnP and a connec-

tion can then be established.

The satellite basic setting is “Quad/DiSEqC™”. Each RF port emits a DiSEqC™ or analogue

switch signal to switch the respective LNB or the multi-switch connection to the required

band.

Additional settings can be made in the web interface of the EXIP 414. You enter

in your web browser, enter the IP address of the EXIP 414, followed by the port 9527,

e. g. 192.168.175.35:9527. The IP address of your EXIP 414 can be found in your router

menu. Alternatively, the IP address can be determined with a software utility such as “Intel ®

Tools for UPnP Technology”.

The Web interface is accessed after entering the password “exip”.

You will nd more detailed instructions for the Web interface on “www.kathrein.de”.

Basic settings (Web interface)

The data stream is fed by the EXIP 414 in

your home network and can be played by

virtually any IP-enabled device

As well as SAT>IP-capable receivers

from our line e.g. the UFS 924 , UFS 906,

UFS 916, it is simply the case of only up-

loading the necessary SAT>IP-Software.

A selection of software for PCs, laptops,

tablet computers and Smartphones can be

found on our website “www.kathrein.de”

under the product description of the

EXIP 414.

To remove the link between the EXIP 414

and the respective SAT> IP-enabled device

please refer to the corresponding software

documentation. Normally this should be

done automatically due to the UPNP inter-

face.

Use

*

)

*

)

*

)

*

)

Up to 20 MBit/s of data are trans-

mitted per channel. Make sure

that your network technology has

sufcient capacity!

7 / 9

Problem Possible cause Solution

LED “Stream”

does not light up

No network connection Connect network cable

LED “Power”

does not light up

On/Off switch is

positioned on “off”

Check the switch on the rear panel

of the unit and set it to “on”

LED “Power”

does not light up

Power supply unit

is not connected

Insert the power supply unit into the

server and connect it to the 230-V mains

Possible causes of faults, and their remedies

Electronic equipment is not domestic waste, - it must be disposed of proper-

ly in accordance with directive 2002/96/EC OF THE EUROPEAN PARLIA-

MENT AND THE COUNCIL dated 27 January 2003 on waste electrical and

electronic equipment. At the end of its service life, please take this device to

a designated public collection point for disposal.

8 / 9

Connection examples (symbolic representation)

**) Over-voltage pro-

tection KAZ 11/12

UAS 584

IP

EXIP 414/E

936.4910/-/VMWI/0215/GB – Technical data subject to change!

Internet: www.kathrein.com

KATHREIN-Werke KG • Anton-Kathrein-Straße 1-3 • P.O. Box 10 04 44 • 83004 ROSENHEIM • GERMANY • Phone +49 8031 184-0 • Fax +49 8031 184-306

Type EXIP 414/E

Order no. 20510103

Subscriber connections 1 x 4

Frequency range MHz 950 – 2,150

Input 4 x Sat

Input level range dBµV 42 – 87

Impedance Ω 75

Permissible remote feed voltage input V 12 – 20

Max. permissible remote feed current mA 400

Output voltage horizontal V > 17.5 (at 400 mA)/< 19 (at 0 mA)

Output voltage vertical V > 12.5 (at 400 mA)/< 14 (at 0 mA)

Control signals 14/18 V, 22 kHz 0,6 V

pp

(EN 61319-1),

DiSEqC™1.0 (EN 61319-1 A11),

Single-cable system (EN 50494)

Power consumption of server W

typ. 12/min. 7

Permissible ambient temperature °C 0 – +40

Connections F-type connectors, RJ 45, 5.5 x 2.5 mm jack plug

Dimensions (W x D x H) mm 222 x 138 x 43

Packing unit/weight pc/kg 1(4)/approx. 0.75

Power supply unit

Nominal input voltage V 230

Secondary voltage V 12

Max. output current A 3

Fullls the directives EN 60065:2002 + A1:2006 +

A11:2008 + A2:2010 + A12:2011

DIN EN ISO 12100-2:2004 + A1:2009 partially

Technical Data

Page is loading ...

Kathrein EXIP 414 User manual

This manual is also suitable for

Kathrein EXIP 414 User manual

in other languages

Related papers

Other documents