BLACK+DECKER ADBEG125 Owner's manual

Page is loading ...

4

ENGLISH

(Original instructions)

Intended use

Your BLACK+DECKER BEG110, BEG120, BEG210 and

BEG220 angle grinders have been designed for grinding and

cutting metal and masonry using the appropriate type of

cutting or grinding disc. When tted with the appropriate

guard, These tools are intended for consumer use only.

Safety instructions

General power tool safety warnings

@

Warning! Read all safety warnings and all

instructions. Failure to follow the warnings and

instructions listed below may result in electric shock,

re and/or serious injury.

Save all warnings and instructions for future reference.

The term "power tool" in all of the warnings listed below refers

to your mains operated (corded) power tool or battery

operated (cordless) power tool.

1. Work area safety

a. Keep work area clean and well lit. Cluttered or dark

areas invite accidents.

b. Do not operate power tools in explosive atmospheres,

such as in the presence of ammable liquids, gases

or dust. Power tools create sparks which may ignite the

dust or fumes.

c. Keep children and bystanders away while operating a

power tool. Distractions can cause you to lose control.

2. Electrical safety

a. Power tool plugs must match the outlet. Never modify

the plug in any way. Do not use any adapter plugs

with earthed (grounded) power tools. Unmodied plugs

and matching outlets will reduce risk of electric shock.

b. Avoid body contact with earthed or grounded

surfaces such as pipes, radiators, ranges and

refrigerators. There is an increased risk of electric shock

if your body is earthed or grounded.

c. Do not expose power tools to rain or wet conditions.

Water entering a power tool will increase the risk of

electric shock.

d. Do not abuse the cord. Never use the cord for

carrying, pulling or unplugging the power tool. Keep

cord away from heat, oil, sharp edges or moving

parts. Damaged or entangled cords increase the risk of

electric shock.

e. When operating a power tool outdoors, use an

extension cord suitable for outdoor use. Use of a cord

suitable for outdoor use reduces the risk of electric shock.

f. If operating a power tool in a damp location is

unavoidable, use a residual current device (RCD)

protected supply. Use of an RCD reduces the risk of

electric shock.

3. Personal safety

a. Stay alert, watch what you are doing and use common

sense when operating a power tool. Do not use a

power tool while you are tired or under the inuence

of drugs, alcohol or medication. A moment of inattention

while operating power tools may result in serious personal

injury.

b. Use personal protective equipment. Always wear eye

protection. Protective equipment such as dust mask,

non-skid safety shoes, hard hat, or hearing protection

used for appropriate conditions will reduce personal

injuries.

c. Prevent unintentional starting. Ensure the switch is in

the off-position before connecting to power source

and/or battery pack, picking up or carrying the tool.

Carrying power tools with your nger on the switch or

energising power tools that have the switch on invites

accidents.

d. Remove any adjusting key or wrench before turning

the power tool on. A wrench or a key left attached to a

rotating part of the power tool may result in personal injury.

e. Do not overreach. Keep proper footing and balance at

all times. This enables better control of the power tool in

unexpected situations.

f. Dress properly. Do not wear loose clothing or

jewellery. Keep your hair, clothing and gloves away

from moving parts. Loose clothes, jewellery or long hair

can be caught in moving parts.

g. If devices are provided for the connection of dust

extraction and collection facilities, ensure these are

connected and properly used. Use of dust collection can

reduce dust-related hazards.

4. Power tool use and care

a. Do not force the power tool. Use the correct power

tool for your application. The correct power tool will do

the job better and safer at the rate for which it was

designed.

b. Do not use the power tool if the switch does not turn it

on and off. Any power tool that cannot be controlled with

the switch is dangerous and must be repaired.

c. Disconnect the plug from the power source and/or the

battery pack from the power tool before making any

adjustments, changing accessories, or storing power

tools. Such preventive safety measures reduce the risk of

starting the power tool accidentally.

d. Store idle power tools out of the reach of children and

do not allow persons unfamiliar with the power tool or

these instructions to operate the power tool. Power

tools are dangerous in the hands of untrained users.

5

ENGLISH

(Original instructions)

e. Maintain power tools. Check for misalignment or

binding of moving parts, breakage of parts and any

other condition that may affect the power tools

operation. If damaged, have the power tool repaired

before use. Many accidents are caused by poorly

maintained power tools.

f. Keep cutting tools sharp and clean. Properly

maintained cutting tools with sharp cutting edges are less

likely to bind and are easier to control.

g. Use the power tool, accessories and tool bits etc. in

accordance with these instructions, taking into

account the working conditions and the work to be

performed. Use of the power tool for operations different

from those intended could result in a hazardous situation.

5. Service

a. Have your power tool serviced by a qualied repair

person using only identical replacement parts. This will

ensure that the safety of the power tool is maintained.

Additional power tool safety warnings

@

Warning! Additional safety warnings Common for

Grinding, Sanding, Wire Brushing, Polishing or

Abrasive Cutting-Off Operations:

u This power tool is intended to function as a grinder,

sander, wire brush, polisher or cut-off tool. Read all

safety warnings, instructions, illustrations and

specications provided with this power tool.

Failure to follow all instructions listed below may result in

electric shock, re and/or serious injury.

u Operations for which the power tool was not designed

may create a hazard and cause personal injury.

u Do not use accessories which are not specically

designed and recommended by the tool manufacturer.

Just because the accessory can be attached to your

power tool, it does not assure safe operation.

u The rated speed of the accessory must be at least

equal to the maximum speed marked on the power

tool. Accessories running faster than their rated speed

can break and y apart.

u The outside diameter and the thickness of your

accessory must be within the capacity rating of your

power tool. Incorrectly sized accessories cannot be

adequately guarded or controlled.

u Threaded mounting of accessories must match the

grinder spindle thread. For accessories mounted by

anges, the arbour hole of the accessory must t the

locating diameter of the ange. Accessories that do not

match the mounting hardware of the power tool will run

out of balance, vibrate excessively and may cause loss of

control.

u Do not use a damaged accessory. Before each use

inspect the accessory such as abrasive wheels for

chips and cracks, backing pad for cracks, tear or

excess wear, wire brush for loose or cracked wires. If

power tool or accessory is dropped, inspect for

damage or install an undamaged accessory. After

inspecting and installing an accessory and run the

power tool at maximum no-load speed for one minute.

Damaged accessories will normally break apart during this

test time.

u Wear personal protective equipment. Depending on

application, use face shield, safety goggles or safety

glasses. As appropriate, wear dust mask, hearing

protectors, gloves and workshop apron capable of

stopping small abrasive or workpiece fragments. The

eye protection must be capable of stopping ying

debris generated by various operations. The dust mask or

respirator must be capable of ltering particles generated

by your operation. Prolonged exposure to high intensity

noise may cause hearing loss.

u Keep bystanders a safe distance away from work

area. Anyone entering the work area must wear

personal protective equipment. Fragments of workpiece

or of a broken accessory may y away and cause injury

beyond immediate area of operation.

u Hold power tool by insulated gripping surfaces only,

when performing an operation where the cutting

accessory may contact hidden wiring or its own cord.

Cutting accessory contacting a "live" wire may make

exposed metal parts of the power tool "live" and shock the

operator.

u Use clamps or another practical way to secure and

support the workpiece to a stable platform. Holding the

work by hand or against your body leaves it unstable and

may lead to loss of control.

u Position the cord clear of the spinning accessory. If

you lose control, the cord may be cut or snagged and your

hand or arm may be pulled into the spinning accessory.

u Never lay the power tool down until the accessory

has come to a complete stop. The spinning accessory

may grab the surface and pull the power tool out of your

control.

u Do not run the power tool while carrying it at your

side. Accidental contact with the spinning accessory could

snag your clothing, pulling the accessory into your body.

u Regularly clean the power tool's air vents. The motor's

fan will draw the dust inside the housing and excessive

accumulation of powdered metal may cause electrical

hazards.

u Do not operate the power tool near ammable

materials. Sparks could ignite these materials.

6

ENGLISH

(Original instructions)

u Do not use accessories that require liquid coolants.

Using water or other liquid coolants may result in

electrocution or shock.

Note: The above warning does not apply for power tools

specically designed for use with a liquid system.

Kickback and related warnings

Kickback is a sudden reaction to a pinched or snagged

rotating wheel, backing pad, brush or any other accessory.

Pinching or snagging causes rapid stalling of the rotating

accessory which in turn causes the uncontrolled power tool to

be forced in the direction opposite of the accessory's rotation

at the point of the binding.

For example, if an abrasive wheel is snagged or pinched by

the workpiece, the edge of the wheel that is entering into the

pinch point can dig into the surface of the material causing

the wheel to climb out or kick out. The wheel may either jump

toward or away from the operator, depending on direction of

the wheel's movement at the point of pinching.

Abrasive wheels may also break under these conditions.

Kickback is the result of power tool misuse and/or incorrect

operating procedures or conditions and can be avoided by

taking proper precautions as given below.

u Maintain a rm grip on the power tool and position

your body and arm to allow you to resist kickback

forces. Always use auxiliary handle, if provided, for

maximum control over kickback or torque reaction

during start-up. The operator can control torque

reactions or kickback forces, if proper precautions are

taken.

u Never place your hand near the rotating accessory.

Accessory may kickback over your hand.

u Do not position your body in the area where power

tool will move if kickback occurs. Kickback will propel

the tool in direction opposite to the wheel's movement at

the point of snagging.

u Use special care when working corners, sharp edges

etc. Avoid bouncing and snagging the accessory.

Corners, sharp edges or bouncing have a tendency to

snag the rotating accessory and cause loss of control or

kickback.

u Do not attach a saw chain woodcarving blade or

toothed saw blade. Such blades create frequent kickback

and loss of control.

Safety warnings specic for grinding and abrasive

cutting-off operations

u Use only wheel types that are recommended for your

power tool and the specic guard designed for the

selected wheel. Wheels for which the power tool was not

designed cannot be adequately guarded and are unsafe.

u The grinding surface of centre depressed wheels

must be mounted below the plane of the guard lip. An

improperly mounted wheel that projects through the plane

of the guard lip cannot be adequately protected.

u The guard must be securely attached to the power

tool and positioned for maximum safety, so the least

amount of wheel is exposed towards the operator. The

guard helps to protect the operator from broken wheel

fragments, accidental contact with wheel and sparks that

could ignite clothing.

u Wheels must be used only for recommended

applications. For example: do not grind with the side

of cut-off wheel. Abrasive cut-off wheels are intended for

peripheral grinding, side forces applied to these wheels

may cause them to shatter.

u Always use undamaged wheel anges that are of

correct size and shape for your selected wheel. Proper

wheel anges support the wheel thus reducing the

possibility of wheel breakage. Flanges for cut-off wheels

may be different from grinding wheel anges.

u Do not use worn down wheels from larger power

tools. Wheel intended for larger power tool is not suitable

for the higher speed of a smaller tool and may burst.

Additional safety warnings specic for abrasive

cutting-off operations

u Do not "jam" the cut-off wheel or apply excessive

pressure. Do not attempt to make an excessive depth

of cut. Over stressing the wheel increases the loading

and susceptibility to twisting or binding of the wheel in the

cut and the possibility of kickback or wheel breakage.

u Do not position your body in line with and behind the

rotating wheel. When the wheel, at the point of operation,

is moving away from your body, the possible kickback may

propel the spinning wheel and the power tool directly at

you.

u When wheel is binding or when interrupting a cut for

any reason, switch off the power tool and hold the

power tool motionless until the wheel comes to a

complete stop. Never attempt to remove the cut-off

wheel from the cut while the wheel is in motion

otherwise kickback may occur. Investigate and take

corrective action to eliminate the cause of wheel binding.

u Do not restart the cutting operation in the workpiece.

Let the wheel reach full speed and carefully re-enter

the cut. The wheel may bind, walk up or kickback if the

power tool is restarted in the workpiece.

u Support panels or any oversized workpiece to

minimize the risk of wheel pinching and kickback.

Large workpieces tend to sag under their own weight.

Supports must be placed under the workpiece near the

line of cut and near the edge of the workpiece on both

sides of the wheel.

7

ENGLISH

(Original instructions)

u Use extra caution when making a "pocket cut" into

existing walls or other blind areas. The protruding

wheel may cut gas or water pipes, electrical wiring or

objects that can cause kickback.

Safety warnings specic for sanding operations

u Do not use excessively oversized sanding disc paper.

Follow manufacturers recommendations, when

selecting sanding paper. Larger sanding paper

extending beyond the sanding pad presents a laceration

hazard and may cause snagging, tearing of the disc or

kickback.

Safety warnings specic for wire brushing

operations

u Be aware that wire bristles are thrown by the brush

even during ordinary operation. Do not overstress the

wires by applying excessive load to the brush. The

wire bristles can easily penetrate light clothing and/or skin.

u If the use of a guard is recommended for wire

brushing, do not allow any interference of the wire

wheel or brush with the guard. Wire wheel or brush may

expand in diameter due to work load and centrifugal

forces.

Safety of others

u This appliance is not intended for use by persons

(including children) with reduced physical, sensory or

mental capabilities, or lack of experience and knowledge,

unless they have been given supervision or instruction

concerning use of the appliance by a person responsible

for their safety.

u Children should be supervised to ensure that they do not

play with the appliance.

Residual risks

Additional residual risks may arise when using the tool which

may not be included in the enclosed safety warnings.

These risks can arise from misuse, prolonged use etc.

Even with the application of the relevant safety regulations

and the implementation of safety devices, certain residual

risks can not be avoided. These include:

u Injuries caused by touching any rotating/moving parts.

u Injuries caused when changing any parts, blades or

accessories.

u Injuries caused by prolonged use of a tool. When using

any tool for prolonged periods ensure you take regular

breaks.

u Impairment of hearing.

u Health hazards caused by breathing dust developed when

using your tool (example:- working with wood, especially

oak, beech and MDF.)

Vibration

The declared vibration emission values stated in the technical

data and the declaration of conformity have been measured

in accordance with a standard test method provided by

EN 60745 and may be used for comparing one tool with

another. The declared vibration emission value may also be

used in a preliminary assessment of exposure.

Warning! The vibration emission value during actual use of

the power tool can differ from the declared value depending

on the ways in which the tool is used. The vibration level may

increase above the level stated.

When assessing vibration exposure to determine safety

measures required by 2002/44/EC to protect persons regularly

using power tools in employment, an estimation of vibration

exposure should consider, the actual conditions of use and the

way the tool is used, including taking account of all parts of

the operating cycle such as the times when the tool is

switched off and when it is running idle in addition to the

trigger time.

Labels on tool

The following pictograms, along with the date code, are shown

on the tool:

Warning! To reduce the risk of injury, the user

must read the instruction manual.

Wear safety glasses or goggles when operating

this tool.

Wear ear protection when operating this tool

Electrical safety

Your charger is double insulated; therefore no

earth wire is required. Always check that the

mains voltage corresponds to the voltage on the

rating plate.

u If the supply cord is damaged, it must be replaced by the

manufacturer or an authorised BLACK+DECKER Service

Centre in order to avoid a hazard.

Voltage drops

Inrush currents cause short-time voltage drops. Under

unfavourable power supply conditions, other equipment may

be affected.

If the system impedance of the power supply is lower than

0.107 Ω, disturbances are unlikely to occur.

8

ENGLISH

(Original instructions)

Features

This tool includes some or all of the following features.

1. On/off switch

2. Spindle lock

3. Guard

4. Side handle

Assembly

Warning! Before assembly, make sure that the tool is

switched off and unplugged.

Fitting and removing the guard (g. A)

The tool is supplied with a guard intended for grinding

purposes only (type 27). If the unit is intended to perform

cutting off operations, a guard specic for this operation (type

41) must be tted. A suitable guard part numbers N551980

(for 115mm cutting wheel) and N542445 (for 125mm cutting

wheel) are available and can be obtained from Stanley Fat

Max service centres.

u Place the tool on a table, with the spindle (4) facing up.

u Release the clamping lock (5) and hold the guard (3) over

the tool as shown.

u Align the lugs (6) with the notches (7).

u Press the guard down and rotate it counterclockwise to

the required position.

u Fasten the clamping lock (5) to secure the guard to the

tool.

u If required, tighten the screw (8) to increase the clamping

force.

Removing

u Release the clamping lock (5).

u Rotate the guard clockwise to align the lugs (6) with the

notches (7).

u Remove the guard from the tool.

Warning! Never use the tool without the guard.

Fitting the side handle

u Screw the side handle (4) into one of the mounting holes

in the tool.

Warning! Always use the side handle.

Fitting and removing grinding discs

(g. B - D)

Always use the correct type of disc for your application.

Always use discs with the correct diameter and bore size (see

technical data).

Fitting

u Fit the guard as described above.

u Place the inner ange (9) onto the spindle (4) as shown

(g. B). Make sure that the ange is correctly located on

the at sides of the spindle.

u Place the disc (10) onto the spindle (4) as shown (g. B).

If the disc has a raised centre (11), make sure that the

raised centre faces the inner ange.

u Make sure that the disc locates correctly on the inner

ange.

u Place the outer ange (12) onto the spindle. When tting

a grinding disc, the raised centre on the outer ange must

face towards the disc (A in g. C). When tting a cutting

disc, the raised centre on the outer ange must face away

from the disc (B in g. C).

u Keep the spindle lock (2) depressed and tighten the outer

ange using the two-pin spanner (13) (g. D).

Removing

u Keep the spindle lock (2) depressed and loosen the outer

ange (12) using the two-pin spanner (13) (g. D).

u Remove the outer ange (12) and the disc (10).

Surface grinding with grinding discs

u Allow the tool to reach full speed before touching the tool

to the work surface.

u Apply minimum pressure to the work surface, allowing the

tool to operate at high speed. Grinding rate is greatest

when the tool operates at high speed.

u Maintain a 20˚ to 30˚ angle between the tool and work

surface as shown in gure F.

u Continuously move the tool in a forward and back motion

to avoid creating gouges in the work surface.

u Remove the tool from work surface before turning tool off.

Allow the tool to stop rotating before laying it down.

Edge grinding with grinding discs

Wheels used for cutting and edge grinding may break or kick

back if they bend or twist while the tool is being used to do

cutoff work or deep grinding. Edge grinding/ cutting with a

Type 27 wheel must be limited to shallow cutting and notching,

less than 13 mm in depth when the wheel is new. Reduce the

depth of cutting/notching equal to the reduction of the wheel

radius as it wears down. Refer to the 'Grinding and cutting

accessory chart' at the end of ths manual for more

information. Edge grinding/cutting with a Type 41 wheel

requires usage of a Type 41 guard.

u Allow the tool to reach full speed before touching the tool

to the work surface.

u Apply minimum pressure to the work surface, allowing the

tool to operate at high speed. Grinding rate is greatest

when the tool operates at high speed.

u Position yourself so that the openunderside of the wheel is

facing away from you.

u Once a cut is begun and a notch is established in the

workpiece, do not change the angle of the cut. Changing

the angle will cause the wheel to bend and may cause

9

ENGLISH

(Original instructions)

wheel breakage. Edge grinding wheels are not designed

to withstand side pressures caused by bending.

u Remove the tool from the work surface before turning the

tool off. Allow the tool to stop rotating before laying it

down.

Warning! Do not use edge grinding/cutting wheels for surface

grinding applications if the wheel label has forbidden such use

because these wheels are not designed for side

pressures encountered with surface grinding. Wheel breakage

and serious personal injury may result.

Fitting and removing sanding discs (g. D & E)

For sanding, a backing pad is required. The backing pad is

available from your Stanley Fat Max dealer as an accessory.

Fitting

u Place the inner ange (9) onto the spindle (4) as shown

(g. E). Make sure that the ange is correctly located on

the at sides of the spindle.

u Place the backing pad (14) onto the spindle.

u Place the sanding disc (15) onto the backing pad.

u Place the outer ange (12) onto the spindle with the raised

centre facing away from the disc.

u Keep the spindle lock (2) depressed and tighten the outer

ange using the two-pin spanner (13) (g. D). Make sure

that the outer ange is tted correctly and that the disc is

clamped tightly.

Removing

u Keep the spindle lock (2) depressed and loosen the outer

ange (12) using the two-pin spanner (13) (g. D).

u Remove the outer ange (12), the sanding disc (15) and

the backing pad (14).

Surface nishing with sanding discs

u Allow the tool to reach full speed before touching the tool

to the work surface.

u Apply minimum pressure to work surface, allowing the tool

to operate at high speed. Sanding rate is greatest when

the tool operates at high speed.

u Maintain a 5˚ to 10˚ angle between the tool and work

surface as shown in gure G.

u Continuously move the tool in a forward and back motion

to avoid creating gouges in the work surface.

u Remove the tool from work surface before turning tool off.

Allow the tool to stop rotating before laying it down.

Using sanding backing pads

Always choose the proper grit sanding discs for your

application. Sanding discs are available in various grits.

Coarse grits yield faster material removal rates and a rougher

nish. Finer grits yield slower material removal and a

smoother nish. Begin with coarse grit discs for fast, rough

material removal. Move to a medium grit paper and nish with

a ne grit disc for optimal nish.

u Coarse = 16 - 30 grit.

u Medium = 36 - 80 grit.

u Fine Finishing = 100 - 120 grit.

u Very Fine Finishing = 150 - 180 grit.

u Allow the tool to reach full speed before touching tool to

the work surface.

u Apply minimum pressure to work surface, allowing the tool

to operate at high speed. Sanding rate is greatest

when the tool operates at high speed.

u Maintain a 5˚ to 10˚ angle between the tool and work

surface as shown in gure H. The sanding disc should

contact approximately 25mm of work surface.

u Move the tool constantly in a straight line to prevent

burning and swirling of work surface. Allowing the tool to

rest on the work surface without moving, or moving the

tool in a circular motion causes burning and swirling marks

on the work surface.

u Remove the tool from work surface before turning tool off.

Allow the tool to stop rotating before laying it down.

Precautions to take when sanding paint

u Sanding of lead based paint is NOT RECOMMENDED

due to the difculty of controlling the contaminated dust.

The greatest danger of lead poisoning is to children and

pregnant women.

u Since it is difcult to identify whether or not a paint

contains lead without a chemical analysis, we recommend

the following precautions when sanding any paint:

u No children or pregnant women should enter the work

area where the paint sanding is being done until all

clean up is completed.

u A dust mask or respirator should be worn by all persons

entering the work area. The lter should be replaced

daily or whenever the wearer has difculty breathing.

Note: Only those dust masks suitable for working with lead

paint dust and fumes should be used. Ordinary painting

masks do not offer this protection. See your local hardware

dealer for the proper approved mask.

u NO EATING, DRINKING or SMOKING should be done

in the work area to prevent ingesting contaminated

paint particles. Workers should wash and clean up

BEFORE eating, drinking or smoking. Articles of food,

drink, or smoking should not be left in the work area

where dust would settle on them.

u Paint should be removed in such a manner as to

minimize the amount of dust generated.

u Areas where paint removal is occurring should be

sealed with plastic sheeting of 4 mils thickness.

u Sanding should be done in a manner to reduce tracking

of paint dust outside the work area.

10

ENGLISH

(Original instructions)

u All surfaces in the work area should be vacuumed and

thoroughly cleaned daily for the duration of the sanding

project. Vacuum lter bags should be changed

frequently.

u Plastic drop cloths should be gathered up and disposed

of along with any dust chips or other removal debris.

They should be placed in sealed refuse receptacles

and disposed of through regular trash pick-up

procedures. During clean up, children and pregnant

women should be kept away from the immediate work

area.

u All toys, washable furniture and utensils used by

children should be washed thoroughly before being

used again.

Fitting and using wire brushes and wire wheels

Wire cup brushes or wire wheels screw directly on the grinder

spindle without the use of anges. b. A Type 27 guard is

required when using wire brushes and wheels. Wear work

gloves when handling wire brushes and wheels. They can

become sharp. Wheel or brush must not touch guard when

mounted or while in use. Undetectable damage could occur to

the accessory, causing wires to fragment from accessory

wheel or cup.

u Thread the wheel on the spindle by hand.

u Depress spindle lock button and use a wrench on the hub

of the wire wheel or brush to tighten the wheel.

u To remove the wheel, reverse the above procedure.

Warning! Failure to properly seat the wheel hub before

turning the tool on may result in damage to tool or wheel. Wire

wheels and brushes can be used for removing rust, scale and

paint, and for smoothing irregular surfaces.

Note: The same precautions should be taken when wire

brushing paint as when sanding paint.

u Allow the tool to reach full speed before touching the tool

to the work surface.

u Apply minimum pressure to work surface, allowing the tool

to operate at high speed. Material removal rate is greatest

when the tool operates at high speed.

u Maintain a 5˚ to 10˚ angle between the tool and work

surface for wire cup brushes as shown in gure I.

u Maintain contact between the edge of the wheel and the

work surface with wire wheels.

u Continuously move the tool in a forward and back motion

to avoid creating gouges in the work surface.

Allowing the tool to rest on the work surface without

moving, or moving the tool in a circular motion causes

burning and swirling marks on the work surface.

u Remove the tool from the work surface before turning the

tool off. Allow the tool to stop rotating before setting it

down.

Warning! Use extra care when working over an edge, as a

sudden sharp movement of grinder may be experienced.

Mounting and using cutting (type 41) wheels

Cutting wheels include diamond wheels and abrasive discs.

Abrasive cutting wheels for metal and concrete use are

available. Diamond blades for concrete cutting can also be

used.

NOTE: A closed, 2-sided Type 41 cutting wheel guard is sold

separately and is required when using cutting wheels. Failure

to use proper ange and guard can result in injury resulting

from wheel breakage and wheel contact. Matching diameter

backing ange and threaded clamp nut (included with tool)

must be used for cutting wheels.

Mounting closed (type 41) guard (Fig. J, K, L)

u Align the three lugs on the guard (7) with the three slots

on the hub. This will align the lugs with slots on the gear

case cover as shown in gure J.

u Push the guard down until the guard lug engages in the

groove on the gear case hub as shown in gure K.

u Rotate guard (7) counterclockwise to lock it into place.

The guard body should be positioned between the spindle

and the operator to provide maximum operator protection

as shown in gure L.

u Tighten the guard latch screw to secure the guard on the

gear case cover. You should be unable to rotate the guard

by hand. Do not operate grinder with a loose guard.

u To remove the guard, loosen the guard latch screw. Then

rotate the guard so that the three lugs on the guard (7)

align with the three slots on the hub and pull up on the

guard.

Mounting cutting wheels

u Place the unthreaded backing ange on spindle with the

raised section (pilot) facing up. The raised section (pilot)

on the backing ange will be against the wheel when the

wheel is installed.

u Place the wheel on the backing ange, centering the

wheel on the raised section (pilot).

u Install the threaded clamp nut with the raised section

(pilot) facing away from the wheel.

u Depress the spindle lock button and tighten clamp nut with

included wrench.

u To remove the wheel, depress the spindle lock button and

loosen the threaded clamp nut with included wrench.

Warning! Do not use edge grinding/cutting wheels for surface

grinding applications because these wheels are not designed

for side pressures encountered with surface grinding. Wheel

breakage and injury may result.

u Allow tool to reach full speed before touching tool to work

surface.

u Apply minimum pressure to work surface, allowing tool to

operate at high speed. Cutting rate is greatest when the

tool operates at high speed.

11

ENGLISH

(Original instructions)

u Once a cut is begun and a notch is established in the

workpiece, do not change the angle of the cut. Changing

the angle will cause the wheel to bend and may cause

wheel breakage.

u Remove the tool from work surface before turning tool off.

Allow the tool to stop rotating before setting it down.

Use

Warning! Let the tool work at its own pace. Do not overload.

u Carefully guide the cable in order to avoid accidentally

cutting it.

u Be prepared for a stream of sparks when the grinding or

cutting disc touches the workpiece.

u Always position the tool in such a way that the guard

provides optimum protection from the grinding or cutting

disc.

Switching on and off

u To switch the tool on, press the on/off switch (1).

u To switch the tool off, release the on/off switch (1).

Warning! Do not switch the tool off while under load.

Hints for optimum use

u Firmly hold the tool with one hand around the side handle

and the other hand around the main handle.

u When grinding, always maintain an angle of approx. 15°

between the disc and the workpiece surface.

Maintenance

Your Stanley Fat Max corded/cordless appliance/tool has

been designed to operate over a long period of time with a

minimum of maintenance. Continuous satisfactory operation

depends upon proper tool care and regular cleaning.

Warning! Before performing any maintenance on corded/

cordless power tools:

u Switch off and unplug the appliance/tool.

u Or switch off and remove the battery from the appliance/

tool if the appliance/tool has a separate battery pack.

u Or run the battery down completely if it is integral and then

switch off.

u Unplug the charger before cleaning it. Your charger does

not require any maintenance apart from regular cleaning.

u Regularly clean the ventilation slots in your appliance/tool/

charger using a soft brush or dry cloth.

u Regularly clean the motor housing using a damp cloth. Do

not use any abrasive or solvent-based cleaner.

u Regularly open the chuck and tap it to remove any dust

from the interior (when tted).

Mains plug replacement (U.K. & Ireland only)

If a new mains plug needs to be tted:

u Safely dispose of the old plug.

u Connect the brown lead to the live terminal in the new

plug.

u Connect the blue lead to the neutral terminal.

Warning! No connection is to be made to the earth terminal.

Follow the tting instructions supplied with good quality plugs.

Recommended fuse: 13 A.

Troubleshooting

Problem Possible cause Possible solution

Unit will not

start.

Cord not plugged

in.

Cord or switch is

damaged.

Plug tool into a

working outlet.

Have cord or switch

replaced at a Stanley

FatMax service center

or authorized

servicer.)

Grinding and cutting accessory chart

Grinding Wheels

Type 27 guard Type 27 guard

Unthreaded backing ange

Type 27 hubbed wheel

Type 27 depressed center

wheel

Threaded clamp nut

12

ENGLISH

(Original instructions)

Sanding Flap Discs

Type 27 guard Type 27 guard

Hubbed sanding ap disc

Unthreaded backing ange

non-hubbed sanding ap

disc

Threaded clamp nut

Type 41 Cutting Wheels

Type 41 guard Type 41 guard

Backing ange Backing ange

Abrasive cutting wheel Diamond cutting wheel

Clamp nut Clamp nut

Wire Wheels

Type 27 guard Type 27 guard

3 inch wire cup brush 4 inch wire cup brush

Sanding Discs

Rubber backing pad

Sanding disc

Threaded clamp nut

Protecting the environment

Z

Separate collection. Products and batteries

marked with this symbol must not be disposed of

with normal household waste.

Products and batteries contain materials that can be

recovered or recycled reducing the demand for raw materials.

Please recycle electrical products and batteries according to

local provisions. Further information is available at

www.2helpU.com

13

ENGLISH

(Original instructions)

Technical data

BEG110 Type 1 BEG120 Type 1

Input voltage V

AC

230 230

Power input W 750 800

Rated speed min

-1

12000 12000

Disc bore mm 22 22

Max disc thickness

Grinding discs mm 6 6

Cutting discs mm 3.5 3.5

Spindle size M14 M14

Weight Kg 1.7 1.7

Level of sound pressure according to EN 60745:

Sound pressure (L

pA

) 96.5 dB(A), uncertainty (K) 3 dB(A)

accoustic power (L

WA

) 107 dB(A), uncertainty (K) 3 dB(A)

Vibration total values (triax vector sum) according to EN 60745:

Surface grinding (a

h,SG

) 6.1 m/s

2

, uncertainty (K) 1.5 m/s

2

Disc sanding (a

h,DS

) 5.6 m/s

2

, uncertainty (K) 1.5 m/s

2

BEG210 Type 1 BEG220 Type 1

Input voltage V

AC

230 230

Power input W 900 900

Rated speed min

-1

12000 12000

Disc bore mm 22 22

Max disc thickness

Grinding discs mm 6 6

Cutting discs mm 3.5 3.5

Spindle size M14 M14

Weight Kg 1.8 1.8

Level of sound pressure according to EN 60745:

Sound pressure (L

pA

) 98 dB(A), uncertainty (K) 3 dB(A)

accoustic power (L

WA

) 109 dB(A), uncertainty (K) 3 dB(A)

Vibration total values (triax vector sum) according to EN 60745:

Surface grinding (a

h,SG

) 5.9 m/s

2

, uncertainty (K) 1.5 m/s

2

Disc sanding (a

h,DS

) 5.4 m/s

2

, uncertainty (K) 1.5 m/s

2

EC declaration of conformity

MACHINERY DIRECTIVE

%

BEG110, BEG120, BEG210, BEG220 Angle grinder

Black & Decker declares that these products described under

"technical data" are in compliance with:

2006/42/EC, EN 60745-1:2009 + A11:2010;

EN 60745-2-3:2011 + A2:2013 + A11:2014

+ A12:2014 + A13:2015

These products also comply with Directive

2014/30/EU and 2011/65/EU.

For more information, please contact Black & Decker at the

following address or refer to the back of the manual.

The undersigned is responsible for compilation of the technical

le and makes this declaration on behalf of Black & Decker..

R. Laverick

Director of Engineering

Black & Decker Europe, 210 Bath Road, Slough,

Berkshire, SL1 3YD

United Kingdom

27/09/2017

Guarantee

Black & Decker is condent of the quality of its products and

offers consumers a 24 month guarantee from the date

of purchase. This guarantee is in addition to and in no way

prejudices your statutory rights. The guarantee is valid within

the territories of the Member States of the European Union

and the European Free Trade Area.

To claim on the guarantee, the claim must be in accordance

with Black & Decker Terms and Conditions and you will need

to submit proof of purchase to the seller or an authorised

repair agent. Terms and conditions of the Black & Decker 2

year guarantee and the location of your nearest authorised

repair agent can be obtained on the Internet at www.2helpU.

com, or by contacting your local Black & Decker ofce at the

address indicated in this manual.

Please visit our website www.blackanddecker.co.uk to register

your new Black & Decker product and receive updates on new

products and special offers.

Page is loading ...

België/Belgique/Luxembourg Stanley Black & Decker Belgium BVBA Tel. NL +32 15 47 37 65

www.blackanddecker.be Egide Walschaertsstraat 16 Tel. FR +32 15 47 37 66

enduser[email protected] 2800 Mechelen Fax. +32 15 47 37 99

Danmark Black & Decker [email protected]

Roskildevej 22 www.blackanddecker.dk

2620 Albertslund

Deutschland Stanley Black & Decker Deutschland Gmbh Tel. 06126 21-0

www.blackanddecker.de Black & Decker Str. 40, D - 65510 Idstein Fax 06126 21-2980

[email protected]

Ελλάδα StanleyBlack&Decker(ΕΛΛΑΣ)Ε.Π.Ε Τηλ. 210-8981616

www.blackanddecker.gr ΓΡΑΦΕΙΑ:Στράβωνος7&Βουλιαγμένης Φαξ 210-8983570

[email protected] 16674Γλυφάδα-Αθήνα

SERVICE: ΗμεροςΤόπος2-ΧάνιΑδάμ Τηλ.Service 210-8985208

19300Ασπρόπυργος-Αθήνα Φαξ 210-5597598

España Stanley Black & Decker Ibérica, S.C.A. Tel. 934 797 400

www.blackanddecker.es Parc de Negocis “Mas Blau” Fax 934 797 419

[email protected] EdicioMuntadas,c/Bergadá,1,Of.A6

08820ElPratdeLlobregat(Barcelona)

France Black&Decker(France)S.A.S. Tel. 0472203920

www.blackanddecker.fr 5 allée des Hêtres Fax 04 72 20 39 00

B.P. 30084

69579 Limonest Cédex

Helvetia ROFOAG Tel. 026-6749393

www.blackanddecker.ch Gewerbezone Seeblick Fax 026-6749394

[email protected] 3213 Kleinbösingen

Italia Stanley Black & Decker Italia Tel. 039-9590200

www.blackanddecker.it Via Energypark 6 Fax 039-9590313

[email protected] 20871Vimercante(MB) Numeroverde800-213935

Nederland Stanley Black & Decker Netherlands BV Tel. +31 164 283 065

www.blackanddecker.nl HoltumNoordweg35,6121REBORN Fax +31164283200

enduser[email protected] Postbus83,6120ABBORN

Norge Black & Decker [email protected]

Postboks 4613, Nydalen www.blackanddecker.no

0405Oslo

Österreich Stanley Black & Decker Austria GmbH Tel. 01 66116-0

www.blackanddecker.at Oberlaaerstraße248,A-1230Wien Fax 0166116-614

[email protected]

Portugal Black & Decker Limited SARL Tel. 214667500

www.blackanddecker.pt Quinta da Fonte - Edifício Q55 D. Diniz Fax 214667580

[email protected] Rua dos Malhões, 2 e 2A - Piso 2 Esquerdo

2770 - 071 Paço de Arcos

Suomi Black&Decker asiakaspalvelu.@sbdinc.com

PL47 www.blackanddecker.

00521, Helsinki

Sverige Black & Decker AB [email protected]

Box 94, 431 22 Mölndal www.blackanddecker.se

Türkiye KALEHırdavatveMakinaA.Ş. Tel. 02125335255

www.blackanddecker.com.tr DefterdarMah.SavaklarCad.No:15 Fax. 02125331005

Edirnekapı/Eyüp/İstanbul34050

United Kingdom & Black & Decker Tel. 01753 511234

Republic Of Ireland 210 Bath Road Fax 01753 512365

www.blackanddecker.co.uk Slough, Berkshire SL1 3YD

[email protected]

Middle East & Africa Black & Decker Tel. +971 4 8863030

www.blackanddecker.ae P.O.Box-17164 Fax +97148863333

[email protected] JebelAliFreeZone(South),Dubai,

UAE

N548345 REV-00

09/2017

BLACK+DECKER ADBEG125 Owner's manual

BLACK+DECKER ADBEG125 Owner's manual

in other languages

Related papers