Stanley 0-77-260 User manual

Page is loading ...

2

GB

User Manual

STANLEY

®

IntelliLaser

TM

Pro Laser Line Level/Stud Finder

The IntelliLaser

TM

Pro Laser Line Level/Stud Finder uses electronic signals to locate the edges of studs,



been detected, the IntelliLaser

TM

Pro display gives visual and audible indications. The laser line gives visual

assistance for accurate marking.

The IntelliLaser

TM

Pro

situations. The IntelliLaser

TM

Pro also incorporates push pins and accommodating mounting holes for

attachment to many wall surfaces.

User Safety

CAUTION: Read and understand all instructions. Failure to follow all instructions listed below may result

in personal injury:

• DANGER: Laser Radiation, avoid direct eye exposure, serious eye injury can result.

• DO NOT

• ALWAYS position the laser so unintentional eye contact will be avoided.

• DO NOT operate the laser around children or allow children to operate the laser.

• DO NOT disassemble. Modifying the product in any way can increase the risk of laser radiation.

WARNING:

this manual may result in hazardous laser radiation exposure.

• DO NOT 

• ALWAYS



• ALWAYS store idle product out of reach of children and other untrained persons. Lasers are dangerous in

the hands of untrained users.

LASER

INTELLI

_

LASERPRO

LASER

INTELLI

_

LASERPRO

LASER

INTELLI

_

LASERPRO

LASER

INTELLI

_

LASERPRO

LASER

INTELLI

_

LASERPRO

LASER

INTELLI

_

LASERPRO

LASER

INTELLI

_

LASERPRO

LASER

INTELLI

_

LASERPRO

LASER

INTELLI

_

LASERPRO

LASER

INTELLI

_

LASERPRO

Lock/Release

Pivot Button

Level Vial

Live Wire Warning LED

Activation Button

LCD Screen

Mounting Hole

LCD

Laser Power

Button

Push Pins

(Internal Storage)

1 2 3 4

LASERLASER

1

Laser Plane

Aperture

Callibration

Indicator

Battery

Indicator

Stud Sensor Mode

LCD Screen

Laser Indicator

AC Detection

3

GB

• ALWAYS use only accessories that are recommended by the manufacturer for you model. Accessories



• DO NOT remove or deface warning labels. Removing labels increases risk of laser radiation.

• DO NOT

result in serious injury.

• DO NOT direct the laser beam toward aircraft or moving vehicles.

• DO NOT

• DO NOT splash or immerse the unit in water.

• ALWAYS turn off the product when not in use.

• ALWAYS ensure battery is inserted in the correct manner, with the correct polarity.

• NEVER intentionally short any battery terminals.

• DO NOT attempt to charge alkaline batteries.

• DO NOT 

• ALWAYS 

• DO NOT dispose of this product with household waste.

• ALWAYS check local codes and properly dispose of used batteries.

• PLEASE RECYCLE in line with local provisions for the collection and disposal of electrical and electronic

waste.

WARNING: Carefully read the User Safety and Operating Instructions before using this

product. The person responsible for the instrument must ensure that all users understand and adhere to

these instructions.

WARNING: The following labels are placed on the laser tool to inform you of the laser class for your

convenience and safety.







The IntelliLaser

TM

Pro



OPERATING INSTRUCTIONS

BATTERY





battery indicator is on.

USAGE

Detecting Wood / Metal Studs

Note: Laser line is always on when holding the activation button.

1) Hold the IntelliLaser

TM

Pro 

button

Note: The unit cannot be moved before calibration is complete.

 

• Keep holding the activation button during all of the following procedures.

Note: Once the activation button is released, the unit shuts off.

 



Note:Laser

TM

Pro



• Slide the IntelliLaser

TM

Pro 



2) 

the laser line emanating from the top of the unit to mark the stud edge.

3-4) Repeat the above steps from the other side of the stud. Coming from the opposite direction, mark the

other edge of the stud.

• The midpoint of the two marks indicates the stud center.

IEC60825-1: 2014

LASERLASER

1

4

GB

User Manual

Detecting Live Wires

 will illuminate and the IntelliLaser

TM

Pro sounds an audible tone, warning



Warning:

Warning:

situations the voltage detection option may not accurately indicate the presence of voltage in the

event of internal device failure or improper operation, and therefore should not be relied upon for





Always turn off AC power when working near wiring.

Always

condition prior to commencing work.

Note: Static electrical charges that can develop on drywall and other surfaces will spread the voltage

detection area many inches on each side of the actual electrical wire. To aid in locating the wire position,





Warning: Shielded wires or wires in metal conduits, casings, metalized walls or thick, dense walls will

not be detected.

Cautions on Operating





Always





the power.

Laser Leveling/Line Generation

 

 

 

 

pressing the laser plane lock/release button.

 

orientation.

Mounting Hole and Push Pins

Two push pins are stored at the bottom part of IntelliLaser

TM

Pro. They are used to mount the IntelliLaser

TM

Pro

OPERATING TIPS

Conventional Construction



IntelliLaser

TM

Pro detects the edge of these double studs and solid headers and emits and holds an audio

signal as it crosses over them.

Surface Differences

The IntelliLaser

TM

Pro will scan through common building materials, Including:

 

 

 

• Linoleum over wood

 

The sensor cannot scan through:

• Carpeting

• Foil faced materials

• Ceramic tile

• Cement or concrete

• Metal & plaster walls

5

GB

Wallpaper

There will be no difference in the function of the stud sensor on surfaces covered with wallpaper or fabric



Ceiling or Textured Surfaces





stud sensor and the surface. Also, it is particularly important in this application to remember to keep your free

hand away from the unit.

Note: The thickness, density and moisture content of the surface material will affect the sensing depth.

IMPORTANT SAFETY NOTICE

Warning: Laser

TM

Pro in the handle area



SPECIFICATIONS



 



 

 

 

 

 

 

 

 

 

1-YEAR WARRANTY

Stanley warrants its electronic measuring tools against deciencies in materials and / or

workmanship for one year from date of purchase.

Decient products will be repaired or replaced, at Stanley’s option, if sent together with

proof of purchase to:

Stanley Black & Decker

210 Bath Road

Slough, Berkshire SL1 3YD

UK

Page is loading ...

Stanley 0-77-260 User manual

Stanley 0-77-260 User manual

in other languages

Related papers

Other documents