Jacobsen 063342 Technical Manual

WARNING: If incorrectly used this machine can cause severe injury. Those who use and maintain this machine must

be trained in its proper use, warned of its dangers and must read the entire manual before attempting to set up,

operate, adjust or service the machine.

WARNING

GB

United

Kingdom

TECHNICAL MANUAL

A SIGNATURE CUT, TRUSTED FOR OVER 100 YEARS

4260472-H

RJL AECC

Eclipse® 2

InCommand™

Honda GX120 - Gen-Set

Series: CAR/AAV/CAQ/AAW/CAP/AAY

063336 – 118F, Floating 18” 11 Blade Reel Option, Gen-Set

063337 – 118F, Floating 18” 15 Blade Reel Option, Gen-Set

063338 – 122, 22” 11 Blade Reel Option, Gen-Set

063339 – 122, 22” 15 Blade Reel Option, Gen-Set

063340 – 122F, Floating 22” 11 Blade Reel Option, Gen-Set

063341 – 122F, Floating 22” 15 Blade Reel Option, Gen-Set

063349 – 122F, Floating 22” 11 Blade Reel Option, Battery Pack

063350 – 122F, Floating 22” 15 Blade Reel Option, Battery Pack

063342 – 126, 26” 7 Blade Reel, Gen-Set

This manual may not be reproduced in whole or in part without the express permission of Ransomes Jacobsen Ltd.

CALIFORNIA PROPOSITION 65

WARNING

The engine exhaust from this product contains

chemicals known to the State of California to cause

cancer, birth defects and other reproductive harm.

!

B

CONTENTS

IMPORTANT...................................................................... 1

PRODUCTION IDENTIFICATION ..................................... 2

DISPOSAL OF SCRAP PRODUCTS ................................ 3

PARTS MANUAL............................................................... 4

KEY NUMBERS................................................................. 4

HOW TO OPERATE SAFELY ........................................... 5

SAFE OPERATION ........................................................... 5

PREPARATION ................................................................. 5

OPERATION...................................................................... 6

SAFE HANDLING OF FUELS ........................................... 6

MAINTENANCE AND STORAGE ..................................... 7

WHEN YOU PUT THE MOWER ON TO TRAILER........... 8

IMPORTANT SAFETY NOTES ......................................... 9

PRODUCT IDENTIFICATION ......................................... 12

MOWER........................................................................... 13

TRACTION AND DIFFERENTIAL ................................... 13

WEIGHTS ........................................................................ 13

GEN-SET POWER MODULE.......................................... 13

DIMENSIONS & WEIGHTS............................................. 14

DECALS .......................................................................... 16

ICONS ............................................................................. 18

HANDLE CONTROLS ..................................................... 18

LCD DISPLAY ................................................................. 19

FREQUENCY OF CUT.................................................... 24

GAS POWER MODULE CONTROLS ............................. 29

BATTERY POWER MODULE CONTROLS .................... 29

DAILY INSPECTION ....................................................... 30

INTERLOCK SYSTEM (O.P.C.) ...................................... 30

OPERATING PROCEDURES ......................................... 31

STARTING/STOPPING ................................................... 32

MOWING ......................................................................... 33

TRANSPORT WHEELS (OPTIONAL)............................. 34

KICKSTAND .................................................................... 34

GRASS CATCHER.......................................................... 35

DAILY MAINTENANCE ................................................... 35

GENERAL........................................................................ 37

BRAKE............................................................................. 37

SPEED PADDLE STOPS................................................ 37

HANDLE ADJUSTMENT ................................................. 38

TRACTION BELTS.......................................................... 38

FRONT ROLLER WEIGHT.............................................. 39

TORQUE SPECIFICATION............................................. 40

GENERAL (FIXED HEAD REEL) .................................... 41

REEL TO BEDKNIFE (FIXED HEAD REELS)................. 41

BEDKNIFE ADJUSTMENT (FIXED HEAD REELS)........ 42

CUTTING HEIGHT (FIXED HEAD REELS) .................... 42

GENERAL (TRUESET FLOATING HEAD REELS)......... 43

BEDKNIFE-TO-REEL (FLOATING HEAD REELS)......... 43

BEDKNIFE ADJUSTMENT ( FLOATING HEAD REELS) 44

CUTTING HEIGHT (FLOATING HEAD REELS) ............. 44

REEL BEARING .............................................................. 44

BEDKNIFE ADJUSTER SPRING .................................... 45

BEDKNIFE ADJUSTER TENSION.................................. 45

GRINDING BEDKNIFE.................................................... 45

REEL ASSEMBLY REMOVAL ........................................ 45

BATTERY POWER MODULE SAFETY .......................... 46

GENERAL MAINTENANCE ............................................ 46

CLEANING BATTERIES ................................................. 47

BATTERY INSTALLATION.............................................. 49

REPLACING BATTERY PACK ........................................50

GEN-SET POWER MODULE - ENGINE .........................51

ENGINE OIL.....................................................................51

ENGINE OIL CHANGE ....................................................52

ENGINE SPEED ..............................................................52

FUEL ................................................................................53

TIRES (OPTION)..............................................................53

WHEEL BEARING ...........................................................53

BACKLAPPING AND GRINDING ....................................54

STORAGE........................................................................55

GENERAL TROUBLESHOOTING...................................57

GENERAL MAINTENANCE AND LUBRICATION ...........58

MAINTENANCE CHART..................................................58

LUBRICATION CHART....................................................59

HOW TO USE THE PARTS CATALOG...........................60

TO ORDER PARTS .........................................................60

PARTS INDEX .................................................................60

HANDLE COVERS.......................................................... 61

HANDLE ASSEMBLY ..................................................... 63

HANDLE TO FRAME MOUNT ........................................65

POWER MODULE MOUNTING PLATE .........................67

FRAME............................................................................ 69

LOWER UNIT.................................................................. 71

REEL ...............................................................................73

GRASS SHIELD AND ROLLER BRACKETS ................. 75

FLOATING HEAD REEL CONNECTION ........................77

OUTER REEL ASSEMBLY .............................................79

INNER REEL ASSEMBLY .............................................. 81

DIFFERENTIAL AND ROLLERS ....................................83

BELTS AND DRIVE MOTORS........................................ 85

HARNESS ROUTING .....................................................87

GENSET POWER SOURCE ...........................................89

BATTERY POWER SOURCE .........................................91

BATTERY CASE .............................................................93

ELECTRICAL SCHEMATIC............................................ 95

en 1

1 FOREWORD

1.1 IMPORTANT _________________________________________________________

The Jacobsen Eclipse 2 is available as a Petrol / Electric Hybrid or All Electric Battery, self propelled walk behind

Reel mower. The Electric systems are for the traction and cutting unit drives.

IMPORTANT: Perform the routine maintenance as indicated in this manual to ensure that the performance and

quality of cut of machine is maintained.

This Technical Manual includes instructions for safety and use of mower and must stay with the machine at all

times. Suppliers of both original and used machines need to keep the documentation that comes with the

machine.

You must only use the machine for its designed purpose of cutting grass and not for any other purpose. Compli-

ance with the conditions of operation, service and repair specified by the manufacturer, are understood to be part

of the correct use.

ALL operators MUST read through this manual and understand the Safety Instructions, controls, lubrication and

maintenance procedures prior to using the machine.

You must not make any changes to the machine that the manufacturer has not approved. Modifications made

without approval can release the manufacturer from liability for any damage or injury.

Discard of worn parts in a environmentally safe way, complying with local legislation and processes according to

the country where the machine is used. When the machine is at its end of life, there are guidelines in this manual

for the removal of the machine from use.

Use only Ransomes Jacobsen Limited Genuine spare parts to make sure that European conformity is controlled.

2006/42/EC

These instructions are the original instructions confirmed by Ransomes Jacobsen Limited.

B

en 2

FOREWORD 1

1.2 PRODUCTION IDENTIFICATION _________________________________________

A. N/A

B. Unladen weight, (No cutting implements or fuel (mass) in Kg

C. N/A

D. Power in Kw

E. Date code

F. Machine type (Designation)

G. Product code

H. Product name

I. Serial number

Location of Serial Number Plate

The serial number plate (A) is found on the right hand side of the

rear chassis frame.

Engine Identification

Location of Serial Number

The engine serial number is found stamped on the body of the

engine block.

Kg Kw

Kg Kg

West Road

Ransomes Europark

Ipswich IP3 9TT

England

ABCD E

FG

HJ

en 3

1 FOREWORD

1.3 DISPOSAL OF SCRAP PRODUCTS ______________________________________

1.3.1 DURING SERVICE LIFE ______________________________________________

Used oil, oil filters and engine coolant are hazardous materials. Recommended procedures must be followed for

their safe removal.

If a fluid leaks, contain the spill to make sure that the leak does not flow into the ground or drainage system. Fol-

low the local laws to make sure that leaks are controlled safely.

The maintenance procedures in this manual make sure that the damage that the machine can cause in the local

environment is controlled safely.

When the machine completes its full service life, the following actions must be taken.

1.3.2 END OF SERVICE LIFE _______________________________________________

These guidelines must be used with applicable Health, Safety and Environmental laws. Always use the approved

local waste disposal and agencies for recycled materials.

• Park the machine in a location to use all of the necessary lifting equipment.

• Use correct tools and Personal Protective Equipment (PPE) and take instruction from the technical manuals

applicable to the machine.

• Remove and store correctly

• Batteries

• Fuel

• Engine coolant

• Oils

• Disassemble the structure of the machine and refer to the technical manuals where applicable. Give attention

to parts that have mechanical pressure or tension applied to the part in the machine,including springs.

• Items that continue to have a service life must be separated and returned to the local store.

• items that are worn must be separated into the material groups and removed according to the agencies for

recycled materials that are available. Common types are as follows:

• Steel

• Non ferrous metals

• Aluminium

• Brass

• Copper

• Plastic materials

• Identified

• Can be recycled

• Can not be recycled

• Not identified

• Rubber

• Electrical and Electronic Components

• If an item is not easily separated into different material groups, the material must be added to the “General

discarded materials” area.

• Do not burn discarded materials.

Change the machinery records to show that the machine is not in service and is discarded. Supply this serial

number to Ransomes Jacobsen Limited Warranty Department to close their records.

B

en 4

FOREWORD 1

1.4 PARTS MANUAL______________________________________________________

In compliance with the ISO14001 standard, Ransomes Jacobsen Limited does not send a paper parts manual

with every product.

To refer to a parts list for this mower you have two options:

1. Website – www.jacobsen.com. Select the “MANUALS” tab at the top, select a brand, product category and

product. You now have access to a PDF version of the parts manual.

Complete the form included in the technical manual pack supplied with the machine if you require a paper copy of

the parts manual.

1.5 KEY NUMBERS_______________________________________________________

Record the key numbers shown below:

Starter Switch:_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _

Diesel tank: _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _

Record the machine and engine numbers shown below:

The machine serial number is found on the registration plate and the engine serial number can be found on the

rocker cover.

Machine Number: _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _

Engine Number:_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _

en 5

2 SAFETY

2.1 HOW TO OPERATE SAFELY ____________________________________________

2.2 SAFE OPERATION ____________________________________________________

a. Read the Operator’s Manual and other training material. If the operator or technician can not read this

manual, the owner is responsible to describe this material to the operators and technicians. Manuals in

additional languages may be available on the Jacobsen website.

b. Read all of the instructions for this mower carefully. Know the controls and the correct operation of the

equipment.

c. Children or persons who do not understand these instructions must not use the mower. The local regula-

tions can limit the age of the operator.

d. Never use a mower near persons, including children or animals.

• Parts could be ejected from the machine at high speed in certain circumstances. The hazard area,

particularly in front of and behind the machine, must be cleared of any persons, animals or objects

before starting.

• Any use of the machine without verification of the hazard area can lead to serious or fatal accidents.

e. Any use of the machine without verification of the hazard area can lead to serious or fatal accidents.

f. Remember that the operator or owner is responsible for accidents or hazards that occur to other persons

or their property.

g. Never carry passengers.

h. Never allow persons to operate or service the mower or its attachments without correct instructions.

i. Do not operate equipment while tired, sick or whilst under the influence of alcohol or drugs.

2.3 PREPARATION _______________________________________________________

a. When you operate the mower, wear correct clothing, slip resistant work shoes or boots, work gloves,

hard hat, safety glasses and hearing protection. Long hair, loose clothing or jewelry can be caught in

moving parts.

b. Do not operate the equipment with the Interlock System disconnected or the system will not operate cor-

rectly. Do not disconnect or prevent the operation of any switch.

c. Never operate equipment that is not in correct order or without decals, guards, shields, deflectors or

other protective devices fastened.

d. Inspect the mower before you operate the mower. Where relevent, check the tyre pressures, fluid levels

and the air cleaner filters. Fuel is highly flammable,use caution when you add the fuel to the mower.

e. Operate the mower in daylight or in good artificial light. Use caution when you operate the mower during

bad weather. Never operate the mower with lightning in the area.

f. Inspect the area to select the accessories and attachments that are needed to correctly and safely do the

job. Only use parts, accessories and attachments approved by Jacobsen.

g. Be careful of holes in the terrain and other hazards that are not visible.

h. Inspect the area where the equipment is operated. Remove all objects you can find before you operate.

Be careful of obstructions above the ground (low tree limbs, electrical wires) and also underground

obstacles (sprinklers, pipes, tree roots). Enter a new area carefully. Look for possible hazards.

i. Inspect the cutting system before you start the mower. Make sure the reel is free to rotate.

WARNING

EQUIPMENT OPERATED INCORRECTLY OR WITHOUT TRAINING CAN BE DANGEROUS.

Know the location and correct operation of controls. Operators without experience must receive

instruction from another person that knows the correct operation of the equipment before you

operate the mower.

Only use parts, accessories and attachments approved by Ransomes Jacobsen Limited.

!

en 6

SAFETY 2

2.4 OPERATION _________________________________________________________

a. Never operate the engine without enough ventilation or in an enclosed area. The carbon monoxide in the

exhaust fumes can increase to dangerous levels.

b. Never carry passengers. Keep other persons or animals away from the mower.

c. Disengage all drives and engage the park brake before you start the engine. Only start the engine with

the operator in the seat. Never start the engine with persons near the mower.

d. Keep your legs, arms and body inside the operator compartment while the mower is in operation. Keep

your hands and feet away from the cutting units.

e. Do not use on the slopes greater than the safe slope limit for the equipment.

f. To guard against over turning or loss of control:

• Operate the mower up and down on the face of slopes (vertically), but not across the face (horizontally).

• Do not start or stop suddenly on slopes.

• Decrease the speed when you operate on slopes or when you must turn. Use caution when you change

direction. Turf condition can change the mower stability.

• Use caution when you operate the mower near drop-offs, ditches or embankments.

• Be careful of holes in the terrain and other hazards that are not visible.

g. When you drive in the reverse direction, look behind you and down to make sure the path is clear. Do not

operate the cutting units when you drive in the reverse direction.

h. Use caution when you go near corners, trees or other objects that can prevent a clear view.

i. Equipment must meet the current regulations to be driven on the public roads.

j. Before you move across or operate on the paths or roads, turn off the PTO switch, lift the mowers and

travel at decreased speed. Look for traffic.

k. Stop the blades when the mower is on any surface that is not grass.

l. Do not release the cut grass in the direction of persons or allow persons near the mower while in opera-

tion.

m. Do not operate the mower with damaged guards or without safety devices in position.

n. Do not change the engine governor setting or over-speed the engine. Never change or tamper with

adjusters that are closed with a seal for the engine speed control.

o. Before you leave the operator compartment, for any reason:

• Disengage all the drives and lower attachments to the ground.

• Engage the park brake.

• Stop the engine and remove the key.

p. When you hit an object or mower starts to cause the vibration that is not normal, inspect the mower for

damage and make repairs.

q. Decrease the throttle setting before you stop the engine.

r. Do not use this equipment for uses that the mower was not made for.

s. The machine and its cutting units are designed for use on maintained turf surfaces. Use of the machine

with its cutting units engaged on hard and rough surfaces could rapidly decrease design life of compo-

nents and potentially cause acute damage to the units making them unsafe for operation.

2.5 SAFE HANDLING OF FUELS____________________________________________

a. The fuel and the fuel vapors are flammable. Use caution when you add the fuel to the mower. The fuel

vapors can cause an explosion.

b. Never use the containers that are not approved to keep or transfer fuel.

c. Never keep the mower or fuel containers near an open flame or any device that can cause the ignition of

fuel or fuel vapors.

en 7

2 SAFETY

d. Never fill the fuel containers inside a vehicle or on a truck or trailer with a plastic liner. Always put the fuel

container on the ground away from your vehicle before you fill the container.

e. Refuel the mower before you start the engine. When the engine is in operation or while the engine is hot,

never remove the fuel cap or add fuel to the mower.

f. Refuel outdoors only and do not smoke when you add fuel. Extinguish all types of ignition.

g. The fuel nozzle must touch the rim of the fuel tank when you add fuel to the mower. Do not use a device

to lock the fuel nozzle in the open position.

h. Do not over fill the fuel tank. Leave at least 1 inch (25 mm) below the filler neck.

i. Always tighten the fuel tank cap and container cap after you add fuel.

j. If the fuel spills on your clothing, change your clothing immediately.

2.6 MAINTENANCE AND STORAGE _________________________________________

a. Before you clean, adjust or repair this equipment, push PTO switch to the OFF position, engage the park

brake, stop the engine and remove the key.

b. Make sure the mower is parked on a solid and level surface.

c. Never work on a mower that is lifted only by a Jack. Always use Axle stands.

d. Never allow persons to service the mower or its attachments without correct instructions.

e. When the mower is parked, put into storage or left without an operator, Keep machine upright, on flat

level ground with parking brake applied.

f. Disconnect the battery before you service the mower. Always disconnect the negative battery cable

before the positive battery cable. Always connect the positive battery cable before the negative battery

cable.

g. Charge the battery in an area with good airflow. The battery can release hydrogen gas that is explosive.

To prevent an explosion, keep any device that can cause sparks or flames away from the battery.

h. Disconnect the battery charger from the power supply before you connect or disconnect the battery char-

ger to the battery. Wear protective clothing and use insulated tools when you service the battery.

i. Be careful and wear gloves when you check or service the cutting unit blades. Replace any damaged

blades, do not try to correct a damaged blade.

j. Keep your hands and feet away from parts that move. Do not adjust the mower with the engine in opera-

tion, unless the adjustment needs the engine in operation.

k. Take care working on cutting units and moving parts with stored energy.

l. To prevent injury from the hot, high pressure oil, never use your hands to check for oil leaks. Use paper

or cardboard to find leaks.

m. The hydraulic fluid pressure can have enough force to enter your skin. If hydraulic fluid has entered your

skin, seek medical attention immediately.

n. Keep the mower and the engine clean.

o. Allow the engine to become cool before storage and always remove the ignition key.

p. Keep all nuts, bolts and screws tight to make sure the equipment is in safe condition.

q. DO NOT operate the machine if you have worn or damaged parts for safety. Replace damaged or worn

decals. Only use parts, accessories and attachments approved by Jacobsen.

r. To decrease the fire hazard, remove materials that burn from the engine, muffler, battery tray and fuel

tank area. In particular dried grass debris.

s. Disconnect the battery and controller connectors before you weld on this mower.

en 8

SAFETY 2

2.7 WHEN YOU PUT THE MOWER ON TO TRAILER____________________________

a. Be careful when you load or unload the mower on a trailer. The trailer must be wider than the mower and

can carry the weight of the mower.

b. Use a full-width ramp to load or unload the mower on a trailer.

c. Use appropriate securing methods to fasten the mower to the trailer. Both front and rear straps must be

sent down and towards the sides of trailer.

d. Make sure that all latches are correctly fastened

en 9

2 SAFETY

2.8 IMPORTANT SAFETY NOTES ___________________________________________

DANGER:

Indicates a dangerous condition that WILL cause death or injury unless it is prevented.

WARNING:

Indicates a dangerous condition that CAN cause death or injury unless it is prevented.

CAUTION:

Indicates a dangerous condition that can cause injury and property damage unless it is prevented. Also, the label

can indicate work procedures that are not safe.

IMPORTANT:

Some illustrations in this manual can show shields, guards or plates removed for clarity. This equipment must not

be operated without these devices correctly fastened and in position.

By following all instructions in this manual, you increase the life of your machine and keep its maximum perfor-

mance. Adjustments and maintenance must always be done by an approved technician.

If a service is needed contact your authorised Jacobsen Dealer or after sales for additional information or help.

WARNING

The Interlock System on this mower prevents the starting of the mower unless a.) The Park Brake is Engaged.

b.) The mow switch is in the OFF position, c.) The traction pedal is in the Neutral position. d) The operator is in

the seat. The system stops the engine when the operator leaves the seat a.) without the Park Brake engaged

and b.) the mow switch is not in the OFF position. NEVER operate the mower unless the Interlock System

is working.

WARNING

1. Before leaving the operator’s position for any reason:

a. Return traction pedal to the Neutral position.

b. Disengage all drives.

c. Lower all cutting units to the ground.

d. Engage Park Brake.

e. Stop the engine and remove the ignition key.

2. Keep your hands, feet, and clothing away from moving parts. Wait for all movement to stop before you

clean, adjust, or service the machine.

3. Keep the area of operation clear of all persons and animals.

4. Never carry any passengers.

Never operate the equipment without guards and deflectors in position.

This safety alert symbol is used to alert you to possible hazards.

!

en 10

SAFETY 2

WARNING

California Proposition 65

Engine exhaust, some of its constituents, and some vehicle components contain or release chemicals known to

the state of California to cause cancer and birth defects or other reproductive harm.

WARNING

To prevent injury from the hot oil at high pressure, DO NOT use your hands to check for oil leaks.

Make sure that you use paper or cardboard.

Release of hydraulic fluid at high pressure has enough force to enter through the skin. If the fluid enters

through the skin, you must seek medical attention immediately.

WARNING

Explosive gases are released by batteries. The battery contains corrosive acid and supplies an electrical

current that is high enough to cause injuries to the body.

WARNING

You must not use this machine to tow other vehicles.

WARNING

Ear protection must be worn when you operate machines with

an operator ear noise level of more than 85dB(A) Leq

!

en 11

2 SAFETY

WARNING

Vibration Exposure Limits

Exposure limits are calculated as a combination of the vibration level (magnitude) of the tool and the Daily

Exposure Time (Trigger Time). e.g. A product with 5m/s² vibration can be used up to 2 hours/day

to reach the EAV and up to 8 hours/day to reach the ELV.

Exposure Action Value (EAV) - Daily vibration exposure A(8) = 2.5m/s²

Where daily vibration exposure A(8) is below 2.5m/s² the risk is relatively low and no

action need be taken.

Exposure Limit Value (ELV) - Daily Vibration Exposure A(8) = 5.0m/s²

If several tools are use the exposure values must be combined:

Total exposure is then the combined value of the activities.

WARNING

Never mow if there is a risk of lightning or you hear thunder. If you are in the middle of mowing, stop in a safe

place, turn off the engine and go inside a building.

CAUTION

When you do any welding on the machine, the battery, controller and display must be disconnected before

you start. You must not open the controller. If the controller is opened, this can void all of the warranties and

can cause the failure of the machine

CAUTION

Personal Protective Equipment (PPE), for example safety glasses, safety footwear, work gloves

and ear protection must be used after the owner/user completes a site specific risk assessment of the

mower to prevent injury.

!

en 12

SPECIFICATIONS 3

3.1 PRODUCT IDENTIFICATION ____________________________________________

063336 / 063337 ........... Eclipse® 2 118F base unit with

Floating 18 in. (457 mm) 11 or

15 blade reel and

InCommand™ control system.

Gen-Set power module.

063338 / 063339 ........... Eclipse® 2 122 base unit with 22

in. (559 mm) 11 or 15 blade reel

and InCommand™ control

system. Gen-Set power

module.

063340 / 063341 ........... Eclipse® 2 122F base unit with

floating 22 in. (457 mm) 11 or

15 blade reel and

InCommand™ control system.

Gen-Set power module.

063349 / 063350 ........... Eclipse® 2 122F base unit with

floating 22 in. (457 mm) 11 or

15 blade reel and

InCommand™ control system.

Battery power module.

63342G01 ..................... Eclipse® 2 126 base unit with 26

in. (660 mm) 7 blade reel and

InCommand™ control system.

Gen-Set power module.

Serial Number An identification plate, like the one shown,

listing the serial number, is attached to the rear crossbar.

Serial Plate

a. N/A

b. Unladen weight, (No cutting implements or

fuel (mass) in Kg

c. N/A

d. Power in Kw

e. Date code

f. Machine type (Designation)

g. Product code

h. Product name

j. Serial number

Serial Plate Location (A)

Engine Serial Code Location: (B)

Kg Kw

Kg Kg

West Road

Ransomes Europark

Ipswich IP3 9TT

England

ABCD E

FG

HJ

A

B

en 13

3 SPECIFICATIONS

3.2 MOWER _____________________________________________________________

Reel............................... 7, 9, 11, or 15 blades, hardened

high manganese carbon steel.

Reel Diameter ............... 5 in. (127 mm)

Cutting Width ................ 18, 22 or 26 in. (457, 559 or

660 mm)

Height of cut.................. 1/16 to 7/16 in. (1.6 to 11 mm)

Bedknives ..................... Hardened carbon steel

High Profile ................5/32” - 7/16” (4 - 11 mm) cut

Low Profile .................1/8” - 7/32” (3.2 - 5.6 mm) cut

Tournament ............... 3/32” - 5/32” (2.4 - 4 mm) cut

Super Tournament..... 5/64” - 7/64” (2.1 - 2.8 mm) cut

Championship ........... 1/16” - 7/64” (1.6 - 2.8 mm) cut

Frequency of Cut

15 Blade Reel............ 0.064 - 0.133 in. (1.6 - 3.4 mm)

11 Blade Reel ............ 0.087 - 0.178 in. (2.2 - 4.5 mm)

9 Blade Reel.............. 0.106 - 0.217 in. (2.7 - 5.5 mm)

7 Blade Reel.............. 0.136 - 0.279 in. (3.4 - 7.1 mm)

3.3 TRACTION AND DIFFERENTIAL _________________________________________

Transport Tires (Option) 11 x 4 pneumatic bidirectional.

Reel Drive ..................... Independent direct drive motor.

Traction Drive................ Independent drive motor with two

synchronous polyurethane belts.

Traction Reduction Ratio15.15:1

Mowing speed ...............0 - 3.4 m.p.h. (5.31 km/h)

Differential ..................... Full automotive type, housed in

traction drum

Rear Drive Drum ...........Machined aluminum alloy

2 Section, 7-3/4 (O.D.) x 10-31/32

3.4 WEIGHTS____________________________________________________________

Gen Set Mowers

Weights: Without Grass Catcher........... Lbs. (kg)

063336 – 118F 11 Blade Option s...... 254(115.2)

063337 – 118F 15 Blade Option s...... 257(116.6)

063338 – 122 11 Blade Option l........ 221(100.2)

063339 – 122 15 Blade Option l........ 224(101.6)

063340 – 122F 11 Blade Option l...... 265(120.2)

063341 – 122F 15 Blade Option l...... 268(121.6)

063342 – 126 7 Blade Optionn.......... 243(110.2)

Battery Pack Mowers

Weights: Without Grass Catcher ........... Lbs. (kg)

063349 – 122F 11 Blade Option l.......285(129.3)

063350 – 122F 15 Blade Option l......288(130.6)

s With Steel Grooved Roller 68618

l With Machined Aluminum Grooved Roller 68614

n With Machined Aluminum Grooved Roller 68617

3.5 GEN-SET POWER MODULE_____________________________________________

Engine......................... Honda GX-120 K1Q JG2 4-

Cycle, 4HP (2.98 kW) at 4000

RPM

Speed.......................... Engine speed set at factory for

generator to produce 59.8 volts

with no load. (2750 to 3250

rpm)

Fuel ............................. Regular Grade (Unleaded)

Fuel Tank .................... 0.66 Gallon (2.5 liter)

Use clean, fresh, regular unleaded gasoline, 85 octane

minimum. Refer to the engine’s operator manual for fuel

recommendations when using blended fuel.

en 14

SPECIFICATIONS 3

3.6 DIMENSIONS & WEIGHTS______________________________________________

To ensure the longest battery life possible, the batteries

are not shipped with the power module and must be

ordered separately. For optimum range and

performance use batteries that equal or exceed the

Amp-hour rating listed.

System Voltage .............48 Volt DC

Batteries .......................(4) 12 volt, valve regulated,

non-spillable sealed lead acid

batteries.

Charger .........................5 Amp, 48 Volt DC, dual input

voltage 115/230 Volt AC, 50/

60 Hz.

Recommended Battery:

CSB battery is the Jacobsen recommended battery for

use in the Eclipse mower.

CSB batteries can be ordered from these CSB distribu-

tors, or from any local battery dealer.

Electronic Distributing

920 Brookstown Ave

Winston Salem, NC 27101

Phone Number - 800-777-1096

URS Electronics

123 N.E. 7th

Portland, OR 97232

Phone Number - 800-955-4877

Alternate Batteries:

These alternate batteries are also currently available.

These batteries have the same dimensions and amp-

hour ratings, but have not been tested by Jacobsen,

and no recommendation is stated or should be implied.

Contact your local battery dealer or the

manufacturer for sourcing on these batteries

.

(USE ONLY 12 VOLT SLA BATTERIES)

Battery Brand Battery Part

Number

CSB EVX12200

Length

in.

(mm)

Width

in. (mm)

Height

in.

(mm)

Weight

lbs.

(kg)

Rating

Amp-Hr

Volt

s

Qty

Req’

d

7-1/8

(181)

3

(76)

6-9/16

(167)

14.7

(6.7)

20 12 4

Battery Brand Battery

Part Number

Yuasa Enersys NPX 80

Panasonic LC-X1220AP

Panasonic LC-X1220P

Discover D12200

Power Sonic PSH-12180

B.B. Battery EB20-12

en 15

3 SPECIFICATIONS

3.7 ACCESSORIES & SUPPORT LITERATURE ________________________________

Contact your area Jacobsen Dealer for a complete listing of accessories and attachments.

Accessories

Lapping Compound (180 grit)........................ 554598

Orange Touch-up Paint (12 oz. spray)........... 554598

18 in. Fixed Head Grass Catcher .................... 68122

18 in. Floating Head Grass Catcher ............ 4174683

22 in. Fixed Head Grass Catcher .................... 68123

22 in. Floating Head Grass Catcher ............ 4114788

26 in. Fixed Head Grass Catcher .................... 68124

22 in. Push Brush (Fixed Head Units) ............. 68611

22 in. Front Roller Brush (Fixed Head)............ 68610

22 in. Front Roller Brush (Floating Head)........ 68536

LED Light Kit.................................................... 63307

Battery Charger ............................................... 68661

Removable Battery Pack (u)............................ 63316

Mower Caddy Battery Pack Mounting Kit........ 68660

11 x 4 - 5 Transport Tires............................. 4368506

11.10 x 4.10/3.50-5 Transport Tires............. 4368507

Mower Caddy .................................................. 63321

Eclipse 2 Mower Caddy Mounting Kit.............. 63354

22 in. Turf Groomer® (n)................................... 67966

Fixed Head Turf Groomer® Adapter Kit............ 67965

MAGKnife Kits

122F Super Tournament MAGKnife Kit ....... 4188500

122F Tournament MAGKnife Kit.................. 4158083

122 Super Tournament MAGKnife Kit ......... 4158082

u Does not included batteries

n Fixed Head Units require 67965 to install Turf

Groomer

Solid Rollers

18 in. with Scraper...........................................68626

22 in. with Scraper...........................................68530

26 in. with Scraper...........................................68627

Grooved Rollers

18 in. Machined Steel ......................................68616

22 in. Assembled Disc ..................................... 68527

22 in. Machined Aluminum............................... 68614

22 in. Machined Steel ......................................68613

22 in. Segmented Roller ..................................68673

26 in. Machined Aluminum............................... 68617

26 in. Machined Steel ......................................68628

Floating Head Reels

22 in. 11 Blade Reel.........................................63308

22 in. 15 Blade Reel ........................................ 63333

18 in. 11 Blade Reel.........................................63309

18 in. 15 Blade Reel ........................................ 62824

Right Hand Reel Conversion Kit..................4172485

Left Hand Reel Conversion Kit ....................4172441

Additional Power Modules

Gen-Set Power Module ................................... 63305

Battery Power Module (u) ................................ 63306

Support Literature

Technical Manual.........................................4260472

Operator Training DVD Video ......................4260475

Fixed Head Repair Manual.......................... 4262932

Floating Head Repair Manual......................4262930

CAUTION

Use of other than Jacobsen authorized parts and accessories may cause personal injury or damage to the

equipment.

!

B

en 16

DECALS 4

4.1 DECALS ____________________________________________________________

Familiarize yourself with the following decals. They are critical to the safe operation of the mower. REPLACE

DAMAGED DECALS IMMEDIATELY.

4170001

STOP

DANGER

To prevent injury, disengage all

drives, engage parking brake, turn

off key switch and disconnect power

connector before working on

machine or emptying grass catchers.

4127335

DANGER

Keep hands and feet

away from the cutting

unit to prevent serious

injury.

4170321

Read the manual before

adjusting engine throttle

lever.

4169840 REV A

DANGER

1. Keep a safe distance from the machine. Keep bystanders away.

2. Properly dispose of components from this machine. Refer to local regulations for waste disposal and

recycling.

3. Refer to the manual for maintenance and service procedures.

4. Do not spray water at electrical connectors, motors or controllers. Do not use high pressure when to

clean mower.

en 17

4 DECALS

Familiarize yourself with the following decals. They are critical to the safe operation of the mower. REPLACE

DAMAGED DECALS IMMEDIATELY.

4265170

4265171

4172240

Read the manual before adjusting

front roller weight.

Disengaged Parking Engaged

Brake

Reel Switch

OFF

On

4265172

Key Switch

Off Position

Run Position

Energize Unit

To Engage Traction.

1. Slide bail to the left.

2. Squeeze bail to handle.

Page is loading ...

Jacobsen 063342 Technical Manual

This manual is also suitable for

Jacobsen 063342 Technical Manual

Related papers

Other documents