2. Hytronik
  3. HED6010 10W Dali 2 LED Driver

Hytronik HED6010 10W Dali 2 LED Driver User manual

  • Hello, I'm your chat assistant. I've reviewed the instruction manual for the HYTRONIK HED6010 LED driver. This document provides information about its DALI and switch-dim dimming capabilities, current configuration via DIP switches, built-in memory, synchronization, and protection features. I'm ready to answer any questions you have about this device.
  • What dimming options does the driver support?
    How can I set the output current?
    Does the driver have a memory function?
    How many drivers can be synchronized?
    What kind of protection does the driver have?
INSTRUCTION MANUAL FOR 10W DALI LED DRIVER
MODEL NO.: HED6010
3rd Floor, block C, complex building, 155#, Bai'gang road south,
Bai'gang village, Xiao Jin Kou town, Huicheng district, Huizhou 516023
Tel:86-752-2772020 F:86-752-2777877
E: [email protected] W:www.hytronik.com
CHINA FACTORY
Room D, 10/f, Tower A, Billion Center, 1 wang Kwong Road,
Kowloon Bay, Kowloon, Hongkong
T: 00852-35197525 F: 00852-30116936
E: [email protected]
HYTRONIK INDUSTRIAL LIMITED
28
122.8
4.1
L
N
DA/P
DA/N
LED+
LED−
mA
500mA
400mA
350mA
300mA
1 2 3 4
250mA
230mA
195mA
WIRING DIAGRAM
Wiring Diagram For DALI Wiring Diagram For Switch-Dim
L
L
N
N
DA/P
DA/P
DA/N
DA/N
LED+
LED−
L
L
N
N
DA/P
DA/P
DA/N
DA/N
LED+
LED−
L
N
L
L
N
N
DA/P
DA/P
DA/N
DA/N
LED+
LED−
L
L
N
N
DA/P
DA/P
DA/N
DA/N
LED+
LED−
L
N
DA
DA
150
52
LED CURRENT SELECTION
The current can be easily configured by choosing the correct
combination of the DIP switches (see table below):
WARNING: Please make sure the correct current is selected before starting the driver!
Highlights
• DALI, switch-Dim dimmable• In compliance with DALI 2 standard
•DALI default feedback
Switch-Dim
• On/off control: short push (<0.5s) on the switch.
Note: Short push should be at least 0.12s, and the time interval between two pushes should be also longer
than 0.12s.
• Stepless dimming: long push (>0.5s) on the switch.
• For fine tuning of light level: With every other long push, the light level goes to the opposite direction.
• Built--in with permanent memory: light returns to the previous dimming level when switched off and on again,
even at power failure.
push and hold to dim
Permanent Memory
This driver has built-in permanent memory against power failure, which means the light always starts up at the previous level when it
was switched off last time.
SPECIFICATION
Up to 64pcs drivers can be connected to the same switch, thanks to the programme. This means there is no need for any additional
synchrony wire in large installation, where many drivers should be controlled by one switch.
Please follow the step below to achieve synchronization function if more than one driver are connected to the same push button:
• Do a long push for more than 15s, then the system is synchronized and all lights in the group dim down to 50%.
Synchronization
Mains voltage
Mains current
Power factor
Operation temperature
Dimming interface
Abnormal protection
EMC standard
Safety standard
DALI standard
Dielectric strength
IP grade
220 ~240VAC 50/60Hz
≥0.90
Ta: -20~+50 Tc:+75℃℃
Output short-circuit protection, Overload Protection, Open-circuit Protection with auto-reset
EN55015, EN61547, EN61000-3-2/-3-3
EN61347-1, EN61347-2-13
CE, CE, EMC
IEC62386-102,207
Input → output : 3000VAC
IP20
71 ~ 65mA
1.5~8W/195mA/6~41V 1.5~9W/230mA/6~41V 2~12W/300mA/6~41V
88%
DALI, Switch-Dim.
Max. output
power/current/voltage
Certification
Max. Efficiency
1.5~10W/250mA/6~41V
2.5~12.8W/350mA/6~36V2.5~12.8W/400mA/6~32V 3~12.5W/500mA/6~25V
/