LIFESPAN KIDS Junior Jungle Panama Owner's manual

Junior Jungle Panama

USER MANUAL

IMPORTANT:

This product may contain sharp points and small parts prior to assembly. The owner’s manual contains

safety, assembly, use and maintenance instructions. This product must be assembled by an adult who

has read and understood these instructions. Keep the packaging away from children and dispose of all

packaging before use.

NOTE:

This manual should not be used to guide your purchasing decision. Your product, and the contents

inside its carton, may vary from what is listed in this manual. This manual may also be subject to

updates or changes. Updated manuals are available through our website at

www.lifespankids.com.au.

For the installer and your children’s safety, it is important to fully read and understand the instructions

and safety hazards before commencing the assembly of the product.

WARNING: The disassembled product may contain small parts

which pose a choking hazard to children under 3.

TABLE OF

CONTENTS

I. GENERAL SAFETY INSTRUCTIONS

1.1 Danger for Children

1.2 Risk of Injuries

1.3 Product Damage

1.4 Assembly Advice

II. SAFETY INSTRUCTIONS

III. ASSEMBLY INSTRUCTIONS

IV. MAINTENANCE

V. WARRANTY

3

4

5

7

25

26

3

I. GENERAL SAFETY INSTRUCTIONS

NOTE: This product is intended for outdoor domestic use only.

WARNING: No eating while using the product at the same time.

• Children do not recognize potential dangers from this product. The unassembled

product must be stored out of reach of children and pets.

• This product may only be used with adult supervision at all times.

• The packaging material is not suitable for children due to choking and suffocation

hazards.

• Do not use the product if it is damaged or defective. If it is damaged or defective, please

contact a qualified technician.

• Check the product before each use. Defective parts must be changed immediately as they

can impair the function and the safety of the product.

• No more than one person to use the product at the same time.

• Use the product only on even and non-slipping surfaces. Never use it near water and keep

sufficient space around for safety.

• Beware of moving parts such as the springs or elastics, which could catch your arms and legs.

Do not place any objects or body parts in the product’s openings.

• Do not make alterations to the product. Only use original spare parts. Qualified

technicians should only carry out repairs – improper repairs can lead to danger for the

user. Use this product only as described in this manual.

1.1 DANGER FOR CHILDREN

1.2 RISK OF INJURIES

1.3 PRODUCT DAMAGE

GENERAL SAFETY INSTRUCTIONS

4

• The assembly of the product must be done carefully and by an able-bodied adult.

If in any doubt, ask a technically qualified person.

• Before you start with the assembly, read the instructions carefully.

• Remove all packaging materials and lay down all parts on an open space.

This gives you an overview and simplifies the assembly procedure.

• Check with the parts list that all parts are available. Dispose of the packaging material

when the assembly is completed.

• Beware that when using tools or doing technical work, there is always a risk of injuries.

Assemble the product with care.

• Create a danger free environment; for example, do not let tools lay around the workspace.

Store the packaging material in a way that cannot cause any danger.

• After installing the product according to the instruction manual, ensure all screws, bolts and

nuts are correctly installed and tightened and that all joints are secure.

• Reasonable space must be kept between the product and possible sources of danger, such

as other equipment swimming pools and fences.

• The product must be assembled correctly before use.

• Your play structure must be installed on a flat horizontal surface with a minimum of 2m

between it and any structure or obstacle such as a fence, garage house, tree branches, cloths

lines, or electric cables.

• Modifications made to the original product shall be carried out according to the instructions

of the manufacturer.

• The product must always be used in a well-lit area.

• Do not place anything under the product.

• Use gloves during assembly and disassembly.

• Outdoor products should be equipped with a device that in strong wind conditions avoid

displacement due to wind (e.g. steel bars in the ground or loads like sandbag or water bags).

• In certain areas during winter, snow buildup and the low temperatures can damage the

product. It is recommended to remove snow buildup and to store the product indoor.

• We strongly recommend visual inspections every 3 months to ensure the integrity of the entire

product. Replace any parts as necessary.

1.4 ASSEMBLY ADVICE

GENERAL SAFETY INSTRUCTIONS

5

• The safety instructions of the product should always be considered and obeyed.

• Using the product may result in permanent injury such as paralysis, or even death. Falling off the

product may lead to injuries, particularly to the back, neck or head.

• No clothes with hooks or lose parts should be worn or carried during product usage in order to

avoid hooks getting caught and causing injury.

• Strong winds can result in the product being blown away or damaged. If strong winds are

predicted the product must be disassembled and moved to a sheltered area or sufficiently

anchored down.

• Moving the product whilst assembled may affect the integrity of the frame. Should it be necessary

to move the product, please consider the following:

1. Force to be evenly spaced around the frame to lift the product off the ground.

2. The product must be carried horizontally.

3. Use caution whilst moving as it could bend the product frame.

• Users should be familiar with the assembly manual. This manual contains assembly guidance;

selected precautionary measures as well as recommendations for servicing and maintenance of

the product, in order to ensure a secured and fun use of the product.

• It is the responsibility of the owner or the supervisor to guarantee that all users of the product are

informed sufficiently of all warning references and safety instructions.

II. SAFETY INSTRUCTIONS

For the supervisor

The supervisor’s role is to make sure users are aware of all safety precautions and that these

precautions are enforced. When a supervisor is not available, the product may be disassembled or

covered to limit access.

• The product can be only used if it is in good condition, worn or damaged parts should be

replaced.

• Objects, which could be dangerous to the user, should be away from the product.

• Avoid unauthorized and unsupervised use of the product.

• Do not use the product under influence of alcohol or drugs (incl. medicines).

• Do not use the product as a jumping platform for other articles.

SAFETY INSTRUCTIONS

6

Consumer Information Sheet for Playground Surfacing Materials

The US Consumer Product Safety Commission (CPSC) estimates that about 100 000 playground

equipment-related injuries resulting from falls to the ground surface are treated annually in US

hospital emergency rooms. Injuries involving this hazard pattern tend to be among the most serious

of all playground injuries, and have the potential to be fatal, particularly when the injury is to the

head. The surface under and around playground equipment can be a major factor in determining

the injury-causing potential of a fall. It is self-evident that a fall on to a shock-absorbing surface is

less likely to cause a serious injury than a fall onto a hard surface. Playground equipment should

never be placed on hard surfaces, such as concrete or asphalt, and while grass may appear to be

acceptable, it may quickly turn to hard-packed earth in areas of high traffic. Shredded bark mulch,

wood chips, tine sand or the gravel are considered to be acceptable shock absorbing surfaces

when installed and maintained at a sufficient depth under and around playground equipment.

Table B.1 lists the maximum height from which a child would not be expected to sustain a life-

threatening head injury in a fall on to four different loose-fill surfacing materials if they are Installed

and maintained at depths of 150 mm, 225 mm and 300 mm.

TABLE B.1: Fall height in millimetres from which a life-threatening head injury would not be expected.

TYPE OF MATERIAL DEPTH OF SURFACING MATERIAL

150mm 225mm 300mm

Double Shredded Bark Mulch

Wood Chips

Fine Sand

Fine Gravel

1800 3000 3300

1800 2100 3600

1500 1500 2700

1800 2100 3000

However, it should be recognised that all injuries due to falls cannot be prevented, no matter what

surfacing material is used.

It is recommended that a shock absorbing material extend a minimum of 1800mm in all directions

from the perimeter of stationary equipment such as climbing frames and slides. However, because

children may deliberately jump from a moving swing, the shock absorbing material should extend

in the front and rear of a swing a minimum distance of twice the height of the pivot point measured

from a point directly beneath the pivot on the supporting structure.

This information is intended to assist in comparing the relative shock-absorbing properties of

various materials. No particular material is recommended over another. However, each material is

only effective when properly maintained. Materials should be checked periodically and replenished

to maintain correct depth as determined necessary for the equipment in question. The choice of

a material depends on the type and height of the playground equipment, the availability of the

material in a particular area, and its cost.

SAFETY INSTRUCTIONS

7

III. ASSEMBLY INSTRUCTIONS

ASSEMBLY INSTRUCTIONS

MONKEY BAR - PARTS LIST

FC 4913 X 2pcs.

FC 4902 X 4pcs.

FC 4905 X 16pcs.

FC 4912 X 9pcs.

FC 4904 X 4pcs.

FC 4908 X 1pc.

FC 4903 X 4pcs.

FC 4906 X 4pcs.

FC 4910 X 1pc. FC 4911 X 4pcs.

M8X48MM

BR 01

28+1pcs.

10pcs.

8pcs. 18+1pcs.

18pcs.

M8X50MM M8X35MM

BR 02

M8X42MM

BR 03

17+1pcs.

9pcs.

M8X60MM

Anchor

32+1pcs.

5pcs.

E

A B FC D

8

STEP 1.1 FRAME & RUNGS ASSEMBLY

STEP 1.2 SUPPORT BARS ASSEMBLY

M8 x 42MM

FC 4906 (x4)

C

Please pay attention to the hole

direction, the big holes are inside

for inserting rungs.

ATTENTION:

Do not over fasten bolts before

complete assembly.

C

F

ASSEMBLY INSTRUCTIONS

9

STEP 2:

FC 4906 (x4)

FC 4902

FC 4902TOP

FC 4902

POSITION 1:

H1880MM

POSITION 2:

H1620MM

POLE DIRECTION

C

A

B

A

BA

AB

ASSEMBLY INSTRUCTIONS

ATTENTION:

Do not over fasten bolts before

complete assembly.

10

STEP 3:

FC 4905 (x16)

FC 4904 (x4)

FC 4903 (x4)FC 4911 (x4)

A

BB

B

C

D

B

1

2

x32

ASSEMBLY INSTRUCTIONS

ATTENTION:

Do not over fasten bolts before

complete assembly.

11

STEP 4:

ATTENTION:

Do not over fasten bolts before complete

assembly.

- The product should be installed over

impact absorbing suraces such as sand,

wood-bar chip, rubber and foam and should

not be installed over concrete, asphalt or

any hard surface.

- Anchors shall be placed level with or

under the gorund in order to reduce tripping

hazards.

FC 4908

FC 4910

A

C

Ex5

ASSEMBLY INSTRUCTIONS

12

SWING SET - PARTS LIST

BR 01

8pcs. 6pcs.

BR 02 BR 03

2pcs.

Anchor

6pcs.

E

FC 5101 X 1pc.

FC 5102 X 2pcs.

FC 5103 X 2pcs. FC 4908 X 2pcs.

FC 4909 X 1pc.

FC 4910 X 1pc.

FC 5104 X 1pc. FC 5105 X 1pc.

14+1pcs. 6pcs.

M8X48MM

AM8X42MM

C

4pcs.

U Bolts

F

ASSEMBLY INSTRUCTIONS

13

COMBINATION A - STEP 1

ATTENTION:

1. DON’T fasten bolts until fully assembled.

2. DON’T over fasten bolts.

3. Before use, please check all bolts and fasten properly.

A

AC

C

POLE DIRECTION: FC 5102

STEP 1

STEP 2

STEP 3

ASSEMBLY INSTRUCTIONS

14

COMBINATION A - STEP 2

ATTENTION:

1. DON’T fasten bolts until fully assembled.

2. DON’T over fasten bolts.

3. Before use, please check all bolts and fasten properly.

A

C

A

ASSEMBLY INSTRUCTIONS

NOTE:

Install as 90 Degree angle before adding

the rope section (Combination B).

15

COMBINATION A - STEP 3: HANG POINTS

FOR SWING SEATS, TRAPEZE BAR

Lock nuts properly.

ATTENTION:

Lock ring is used for

adjusting chain height.

Lock both nuts properly.

Option 1: Standard -Swing seat + Trapeze Option 2: Hang points are available for Dia 1M

Web Swing ( web swing not included)

1. Hang method for Trapeze bar.

2. Hang method for swing seat.

380mm

Ground

Hang point Hang

point

ASSEMBLY INSTRUCTIONS

16

COMBINATION A - STEP 4

Ex6

ASSEMBLY INSTRUCTIONS

17

CLIMBING NET & ROPE - PARTS LIST

FC 5201 X 1pc.

FC 5202 X 1pc.

FC 5203 X 1pc.

FC 5204 X 1pc.

Climbing Rope - FC 5205 X 1pc.

Climbing Net - FC 5206 X 1pc.

FC 4908 X 2pcs. FC 4909 X 1pc.

FC 4910 X 1pc.

18+1pcs. 4pcs.

M8X48MM

AM8X42MM

C

1pc.

U Bolts

F

14pcs.

BR 02 BR 03

4pcs. 4pcs.

Anchor

E

4pcs.

BR 01

ASSEMBLY INSTRUCTIONS

18

COMBINATION B - STEP 1

ATTENTION:

1. DON’T fasten bolts

until fully assembled.

2. DON’T over

fasten bolts.

3. Before use, please

check all bolts and

fasten properly.

ATTENTION:

Before starting building LK52 Climbing Net and Rope,

Please unfasten the bolts on one of support bar, then turn 90 degree

as picture showing. After that, please fasten bolts properly and anchor it.

ASSEMBLY INSTRUCTIONS

19

Step 1. Lay out Frames (FC5204/5202/5203/5201) and Net (FC5206) as below.

FC 5204

FC 5202

FC 5201

FC 5203

Step 2. Insert frame through net loops as below.

Repeat same actions for 4 sides.

FC 5206

COMBINATION B - STEP 2

ASSEMBLY INSTRUCTIONS

20

FC 5204

A

FC 5203

FC 5201

A

POLE DIRECTION: FC5202

FC 5204

FC 5202

FC 5201

A

COMBINATION B - STEP 3

ATTENTION:

1. DON’T fasten bolts until fully assembled.

2. DON’T over fasten bolts.

3. Before use, please check all bolts and

fasten properly.

POLE DIRECTION: FC5203

FC 5203 TOP

FC 5202 TOP

ASSEMBLY INSTRUCTIONS

Page is loading ...

LIFESPAN KIDS Junior Jungle Panama Owner's manual

LIFESPAN KIDS Junior Jungle Panama Owner's manual

Related papers

Other documents