Electric water pump
Instructions and user manual
BE1450ASC
Millasur SLU
Rúa Eduardo Pondal, nº 23 - Pol. Ind. Sigüeiro
15688 – Oroso, A Coruña - 981 696 465 - www.millasur.com
EN
EN
2
Anova wishes to congratulate you for having chosen one of our products
and guarantees you the assistance and cooperation that has always
distinguished our brand over time.
This machine is designed to last many years and to be very useful if it is
used according to the instructions contained in the user manual. We
therefore recommend that you read this instruction manual carefully and
follow all our recommendations.
For more information or questions you can contact us through our web
supports such as www.anova.es
INFORMATION ABOUT THIS MANUAL
Pay attention to the information provided in this manual and on the
appliance for your safety and the safety of others.
- This manual contains instructions for use and maintenance.
- Take this manual with you when you go to work on the machine.
- The contents are correct at the time of printing.
- They reserve the rights to make alterations at any time without
affecting our legal responsibilities.
- This manual is considered an integral part of the product and must
remain with it in case of loan or resale.
- Ask your dealer for a new manual in case of loss or damage.
READ THIS MANUAL CAREFULLY BEFORE USING THE MACHINE
To ensure that your machine provides the best results, please
read the use and safety regulations carefully before using it.
OTHER WARNINGS:
Incorrect use could cause damage to the machine or other objects.
The adaptation of the machine to new technical requirements could cause
differences between the content of this manual and the purchased
product.
Read and follow all instructions in this manual. Failure to follow these
instructions could result in serious personal injury.
EN
4
1. SECURITY INSTRUCTIONS
1.1. Safety symbols
HeThe use of safety symbols is intended to draw your attention to potential hazards. The safety
symbols and the explanations that accompany them must be fully understood. Warnings by
themselves do not eliminate risks and cannot replace correct actions to prevent accidents.
Read the instruction manual and follow all warnings and safety instructions
before any use, refer to the corresponding paragraph in this manual.
It complies with the European regulations applicable to this product.
When using the product, wear protective equipment that prevents injuries,
such as non-slip shoes.
The pump must be grounded to prevent leakage and must be equipped with
a leakage protection switch.
If the pump is used outdoors, you must use an outdoor extension cord with
rubber cord.
1.2. Other safety instructions
1. Before installation and use, please thoroughly check whether the electric pump was
damaged during transportation and storage, as well as check whether the cables are
intact. If there is any damage, repair or replace before using the water pump.
2. Do not touch the pump after turning it on.
3. By connecting the hose to the water outlet, it can be fastened with a clamp.
4. When the water pump is in motion, the cable cannot be pulled.
EN
5
a. The handle must be attached to a rope before starting the electric pump on the
job site.
b. When transporting the electric pump, do not use the cable or the float switch as
a handle.
5. When the electric pump is immersed in the water, the immersion depth cannot be less
than 0.5m, nor more than 5m, and it cannot be immersed in the mud. During the
working process, the water level should be checked frequently, and the electric pump
should not be allowed to work above the water surface.
6. When the electric pump is working, safety warning signs should be installed at the use
site to prevent accidents.
7. When the electric pump is in normal operation, the built-in thermal protector will not
work. Once the protector is frequently disconnected, the power supply should be cut
off, the reason should be checked, and the fault can be eliminated before use.
8. If the ground is far from the power supply, please refer to the following table to increase
the thickness of the cable according to the distance.
Power Voltage
Recommended cable length
(50m)
(100m)
(200m)
1.1 kW
220V
1mm2
1.5mm2
2.5mm2
9. The motor is a dry structure and it is not allowed to fill the motor cavity with oil or water.
10. The oil chamber of the electric pump is filled with oil to ensure that the mechanical seal
is effectively lubricated and cooled. In case of product damage, leakage may occur.
In planting, breeding, or drinking water, food transportation, and processing
environments, leaked oil can cause damage to plants, crops, or damage to drinking
water, food, etc. and produce pollution. The environment of use and the consequences
must be evaluated before choosing this product. In case of oil leakage, stop using it
immediately and dispose of it properly.
11. When the pump is working, if it is necessary to adjust the position of the pump or there
is an action to contact the pump, the power must be cut off first to avoid accidents.
EN
6
Note: If the pump is touched while it is running, the power must be cut off.
12. When the electric pump is in operation, it is strictly prohibited to immerse the connecting
cable or plug plate in water. If it is necessary to lengthen the level of the wiring, the joint
must be properly sealed to prevent water and electricity leakage.
13. After turning off the pump, please wait to take the pump out of the water when the
engine cools down to normal temperature to ensure safety.
2. TECHNICAL SPECIFICATIONS
Characteristics
Power
1.1 kW – 1.5 HP
maximum flow
25 m³/h – 417 L/min
suction depth
14m*
Entrance exit
G2
Voltage
180-220V ~ 50Hz
RPM
2850 min-1
outlet diameter
2"
IPX protection index
IPX8
*Note: 14m with immersion intervals not exceeding 5m
D (mm)
fifty
L(mm)
269
W (mm)
186
H (mm)
426
EN
7
3. INSTRUCTIONS FOR USE
3.1. Before using
Always read the instruction manual carefully and check the machine before using it.
Submersible sewage pumps are suitable for buildings, hospitals, residential quarters,
municipal engineering, traffic and road construction, factory sewage, sewage treatment and
the like.
It is used to discharge sewage, rainwater and sewage containing small solid particles.
3.2. Terms of use
• Voltage and frequency: see technical specifications.
• Max water temperature: 40℃
• PH value water: 4-10
• Maximum water density: 1200 kg/m³
• The volume ratio of solid impurities in the medium should not exceed 2%.
• Protection class: IPX8
It cannot be used with strong corrosive liquids and strong abrasive particles.
The particle size should not be larger than the largest particle diameter that is allowed to pass.
4. MAINTENANCE AND CLEANING
Good maintenance is essential for safe and efficient operation. It will also help increase the life
of the machine.
The purpose of the maintenance and adjustment program is to keep the machine in the best
operating condition.
Always select accessories recommended and approved by the manufacturer. The use of other
non-approved accessories and spare parts may damage the machine. Remove safety devices
after or during maintenance.
Periodically check the insulation resistance of the electric pump. When close to working
temperature, the insulation resistance should be more than 50 MΩ (megohms). Otherwise,
appropriate measures must be taken to meet the requirements before use.
Note: If the pump is not used for a long time, it should be cleaned and placed in a dry and ventilated
place.
EN
8
Maintenance of the electric pump should be carried out according to the following steps:
5. STORAGE
Store the machine, the instructions for use and, if applicable, the accessories in the original
packaging. In this way, you always have all the information and parts at hand.
Pack the product well or use the original packaging to avoid damage during transport. Wear
protective gloves when handling cutting accessories.
Store the machine in a dry and well-ventilated place. Do not store fuel near the machine.
1). Disassemble the
pump body.
2). Unscrew the
turbine screw and
check that it is not
worn.
3). Remove the
turbine.
4). Remove the oil
chamber cover, pour
out the oil, and
check if there is any
water stain in the oil.
5). Remove and
replace with a new
mechanical seal.
6). Install the oil
chamber cover and
fix it with screws.
7). Carry out the air
pressure test in the oil
chamber with an air
pressure of 0.3 MPa,
about 3 minutes, and
the pressure gauge
should always read
0.3 MPa.
8). Add oil in the oil
chamber and then
screw the screw back
in (be careful not to
lose the o-ring).
EN
9
6. TROUBLESHOOTING
Warning
Risk of injury if the engine starts suddenly. Protect yourself against injury. Before doing any
work on this product:
- Turn off the machine.
- Wait until all moving parts have stopped.
- Unplug the machine.
Turn off the power before repairing the water pump.
Problem
possible cause
Solution
Difficult start up.
1. The voltage is low.
1. Adjust the voltage to the nominal value
±6%.
2. Loss of phase. 2. Check the wires, cord and plug.
3. The turbine is clogged. 3. Clean the turbine.
4. Cable voltage drop is high. 4. Select a suitable cable.
5. The stator is damaged. 5. Contact your official distributor.
The flow is low
1. Maximum dump height too high. 1. See the recommended height range.
2. The pump inlet is blocked. 2. Clean the inlet of the pump.
3. The turbine is damaged.
3. Replace the turbine.
4. The immersion depth is not enough.
4. Set the immersion depth to more than
0.5m.
The pump stops
suddenly.
1. The thermal protector is activated or the fuse
is blown. 1. Check the voltage.
2. The turbine is clogged.
2. Clean the turbine.
3. The stator is damaged. 3. Contact your official distributor.
7. WARRANTY
If your product suffers from a manufacturing defect during the established warranty period,
contact or go to your point of sale directly with the necessary documentation.
Your purchase invoice must be kept as proof of the purchase date. Your tool must be returned
to your dealer in an acceptable and clean condition, in its original molded case, if applicable to
the unit, accompanied by your appropriate proof of purchase.
7.1. Warranty period
The legal warranty period for the product begins on the original date of purchase by the first
initial buyer and its duration will be that established by the Royal Decree-Law for the protection
of consumers and users in situations of social and economic vulnerability for the year.
corresponding to the time of purchase of the product.
EN
10
Some countries do not allow limitations on how long an implied warranty lasts or do not allow
the exclusion or limitation of consequential or incidental damages, in which case the above
limitation and exclusion may not apply to you. This warranty gives you specific legal rights, and
you may also have other rights which vary from state to state or country to country.
7.2. exclusions
This warranty does not cover product damage or performance problems caused by:
- Natural wear and tear from use.
- Misuse, neglect, careless operation or lack of maintenance.
- Defects caused by incorrect use, damage caused by manipulations carried out by
personnel not authorized by Anova or use of non-original spare parts.
- Defects of normal wear parts, such as bearings, brushes, cables, plugs or accessories
such as drills, bits, saw blades, etc.
- Damage or defects resulting from abuse, accidents or alterations.
- Incorrect use and storage (explicit reference that the rules described in the operating
instructions have not been followed).
- Customer wear (for example, broken saw blades, worn carbon brushes, etc.).
- Secondary wear and damage due to lack of maintenance, repair, lubricants (for
example, damage from overheating due to blocked cooling slots, bearing damage as a
result of dirt, frost damage, etc.)
- Damage as an obvious result of overuse/overloading.
- Damage caused by inappropriate supplies (eg wrong fuel)
- Load-induced failure of housing components or accessories due to abnormal stress
- Load-induced deformation of housing components or accessories due to abnormal
stress.
- Damage resulting from the operation of supplies that are overfilled or leaking due to
improper storage, in proper cleaning agents or other damaging chemicals.
- Damage due to improper exposure to extreme temperatures (for example, freeze
fractures, thermal distortion of components, etc.)
- Damage from permanent exposure to ultraviolet radiation.
- Damage caused by improper maintenance.
- Any damage caused by non-compliance with the instruction manual
- Any product that has been attempted to be repaired by an unqualified professional.
- Any product connected to an inadequate power source (amps, voltage, frequency).
- Any damage caused by external influences (water, chemicals, physics, shock) or
foreign substances.
- Use of inappropriate accessories or parts.
- It does not include defects of normal wear parts, nor does it cover damages or defects
resulting from abuse, accidents or alterations, nor transportation costs.
Also, the warranty is void if the product has been altered or modified, or if the trademark/serial
number on the machine has been defaced or removed.
Routine maintenance, tune-ups, adjustments or normal wear and tear are not covered under
this warranty.
This manual does not cover all possible situations regarding warranty exclusions, for more
information contact your nearest Anova dealer.
EN
11
7.3. In case of incident
The guarantee must be correctly completed with all the information requested, and
accompanied by the purchase invoice.
Anova reserves the right to deny any claim where purchase cannot be verified or where it is
clear that the product was not maintained properly (maintenance, vents cleaned, lubrication,
carbon brushes regularly maintained, cleaning, storage, etc.). .
Private use is understood as personal domestic use by a final consumer. Instead, commercial
use means all other uses, including uses for commercial, income-generating, or rental
purposes. Once the product has been used for commercial use, it will hereafter be considered
a commercial use product for the purposes of this warranty.
These are our standard warranty terms, but occasionally there may be additional warranty
coverage not determined at the time of publication. For more information, contact your nearest
official Anova distributor or by visiting www.millasur.com.
Warranty service is only available through official Anova dealers. You can locate your nearest
distributor on our distributor map at www.anova.es.
8. ENVIRONMENT
Protect the environment. Recycle the oil used by this machine by taking it to a recycling center.
Do not pour used oil into drains, land, rivers, lakes or seas.
Dispose of your machine in an ecological way. We must not dispose of the machines
together with the household waste. Its plastic and metal components can be classified
according to their nature and can be recycled. The materials used to pack this machine
are recyclable. Please do not dispose of the packaging in the household waste. Dispose
of these packages at an official waste collection point.
EN
12
9. EXPLODED VIEW
BE1450ASC
EN
13
10. CE CERTIFICATE
DISTRIBUTION COMPANY
MILLASUR, SLU
RUA EDUARDO PONDAL, Nº 23 PISIGÜEIRO
15688 OROSO - A CORUÑA
SPAIN
EC DECLARATION OF CONFORMITY
In compliance with the different CE directives, this document confirms that, due to its design
and construction, and according to the CE mark printed on it by the manufacturer, the machine
identified in this document complies with the pertinent and fundamental health and safety
requirements. of the aforementioned EC directives. This declaration validates the product to
display the CE symbol.
In the event that the machine is modified and this modification is not approved by the
manufacturer and communicated to the distributor, this declaration will lose its value and
validity.
Machine name: ELECTRIC WATER PUMP
Model: BE1450ASC
Recognized and approved standard to which it conforms:
Directive 2006/42/EC
2014/30/EU
2014/35/EU
Tested according to regulations:
ENISO 12100:2010
EN 809:1998+A1:2009+AC:2010
IN 60204-1:2018
EN IEC 60335-2-41:2021+A11:2021
EN 62233:2008+AC:2008
EN 60034-1:2010+AC:2010
EN IEC 55014-1:2021
EN IEC 55014-2:2021
EN IEC 61000-3-2:2019+A1:2021
EN IEC 61000-3-11:2019
EN 60335-1:2012+A11:2014+A13:2017+
A1:2019+A14:2019+ A2:2019+A15:2021
Company seal
07/03/2023
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
Other documents
-
SIP 01976 User manual
-
MYERS DE and DSW Series Submersible Effluent and Sewage Pump Owner's manual
-
-
Alto 772 User manual
-
Flotec E75VLT Owner's manual
-
Anova Culinary A2.2-120V-US User guide
-
Kohler KD1350 Operating instructions
-
EBARA DDLFMU Operating Instructions, Installation & Maintenance Manual
-
Zoeller FM2102 User manual
-
WilTec 50741 User manual
