FLCNC F7600 CNC Cutting Controller User manual

Brand: FLCNC

Model: F7600 CNC Cutting Controller

Type: User manual

Fangling CNC Cutting Machine

Control System

Instructions for F7600 Series CNC Cutting System (V2.2)

ShangHai FangLing Computer Software Co. ,LTD

May 2019

User Manual for F7600 Series CNC Cutting System

Version

Number

Date

Modification Description

Modification

Author

Remark

V1.0

July 1, 2017

Initial Version

Hu Zhiqiang

V1.1

May 1,

2018

V1.0 Revision

Yin Wenlou

V1.2

August 22,

2018

Update the interface image.

Add the descriptions for calling the

FLCAM function.

Add the descriptions for network disk

features.

Add the descriptions for task save and

load function.

Yin Wenlou

October 31,

2018

Increase the wiring instructions for the

Y-axis dual drive.

Yin Wenlou

December

10, 2018

Increase the content of the factory

backup and restore.

Improve the contents authorized by the

manufacturer

Yin Wenlou

V2.0

April 16,

2019

Increase wiring with FCB1200PC

Increase the wiring descriptions with

the remote control F1510, 1520

Add F7600 series (models include:

F7600W-DE, F7600W-IN,

F7600WF-IN, F7600S-DE,

F7600S-IN, F7600SF-IN)

Hao Qian

V2.1

June 6,

2019

Add double-trolley interface and

configuration descriptions

Increase the height adjustment

configuration descriptions

Add new button function descriptions

(joystick calibration, shutdown, restart

axis card, etc.)

Update some interface images

Shi

Qianyang

V2.2

August 7,

2019

Increase visual residual material and

jacking functions

Increase visual residual calibration

function

Increase drill and cut function

Zhao

Chaojie

User Manual for F7600 Series CNC Cutting System

Precautions

Reading Manual

This Manual applies to the F7600 series CNC cutting machine control system

produced by Shanghai Fangling Software Co., Ltd. Please read this Instruction Manual

and local safety regulations carefully before use.

Due to continuous improvement of this product, the technical parameters and

hardware parameters involved in this Manual are subject to change without notice. If

you have any other questions or opinions about this product, but the contents of this

Manual are not exhaustive, please consult in time, and we will be happy to answer your

questions, and receive your suggestions and criticism. Thank you again for your choice

and your trust.

The design of this product is not suitable for on-site maintenance. If you have any

maintenance requirements, please contact:

Sales: +86-21-34290970

After sales: +86-21-34121295

Fax: +86-21-34290970

E-mail: [email protected][email protected] Website: www.flcnc.com

Environmental Requirements

 This numerical control system is suitable for working at an ambient temperature of

0 °C to 50 °C, and a relative humidity of 5%-95% without condensation.

 The working voltage is DC +24V.

 This controller should be installed in a console enclosure with protective dust.

 The system is preferably used away from high voltage, high frequency and high

radiation.

Maintenance

 Hands and feet shall be away from the moving machine, and the control operation

or manual can be performed through the front panel keyboard.

User Manual for F7600 Series CNC Cutting System

III

 Loose clothing and the clothing with lines and ropes shall not be worn when the

machine is operated to prevent from being caught by the machine.

 This equipment should and can only be operated by trained personnel.

 Those other than technical staff authorized by the Company shall be strictly

forbidden to dismantle the machine.

 When the machine is used, acidic, alkaline, corrosive and other items shall not

splash on the control system.

High pressure

 Electric shock can hurt people to death. It must be installed in accordance with the

steps and requirements of the packing parts.

 When the power is turned on, the wires and cables cannot be touched.

 This equipment should and can only be operated by trained personnel.

User Manual for F7600 Series CNC Cutting System

Contents

Fangling CNC Cutting Machine Control System ............................................................................. 1

Precautions ....................................................................................................................................... II

Reading Manual ........................................................................................................................ II

Environmental Requirements .................................................................................................... II

Maintenance .............................................................................................................................. II

High pressure ........................................................................................................................... III

Chapter 1 Introduction of F7600 Control System ...................................................................... 1

1.1 Introduction ........................................................................................................................ 1

1.2 System Features .................................................................................................................. 1

1.3 Technical indicators ............................................................................................................. 2

1.4 F7600 series standard configuration ................................................................................... 3

1.5 F7600S standard configuration ........................................................................................... 4

Chapter 2 System Boot .............................................................................................................. 6

2.1 System startup and main interface description .................................................................. 6

2.2 Main interface function index ............................................................................................. 8

Chapter 3 Cutting Function ....................................................................................................... 9

3.1 Cutting function index ....................................................................................................... 12

3.1.1 Normal speed regulation........................................................................................ 12

3.1.2 Rapid speed regulation .......................................................................................... 12

3.2 Advance ............................................................................................................................. 13

3.3 Back ................................................................................................................................... 13

3.4 Offset cutting / cutting back / just back ............................................................................ 14

3.5 Resetting function ............................................................................................................. 15

3.6 Oxygen gas preheating time adjustment .......................................................................... 15

3.7 Select the piercing point ................................................................................................... 16

3.8 Dynamic zoom ................................................................................................................... 17

3.9 Exit cutting ........................................................................................................................ 18

3.10 Walking frame ................................................................................................................. 18

3.11 Statistics function ............................................................................................................ 19

3.11.1 Related statistics: ................................................................................................. 19

3.11.2 Statistics display ................................................................................................... 19

Chapter 4 Component Options ................................................................................................ 22

4.1 Starting point selection ..................................................................................................... 22

4.2 Angle correction ................................................................................................................ 23

4.2.1 Steel plate correction ............................................................................................. 23

4.3 Repeated arrangement ..................................................................................................... 25

4.4 Scale .................................................................................................................................. 28

4.5 Selection of lines and holes ............................................................................................... 28

4.5.1 Hole selection ......................................................................................................... 29

4.5.2 Line selection ......................................................................................................... 29

4.5.3 Operation after selecting a line .............................................................................. 29

4.6 Graphics restoration .......................................................................................................... 30

Chapter 5 Manual Functions .................................................................................................... 32

User Manual for F7600 Series CNC Cutting System

5.1 Jog ..................................................................................................................................... 32

5.2 Linkage .............................................................................................................................. 32

5.3 Fixed length movement ..................................................................................................... 33

5.4 Break restoration ............................................................................................................... 33

5.5 Laser offset ........................................................................................................................ 34

5.6 Double-trolley ................................................................................................................... 35

5.6.1 Double-trolley configuration interface ................................................................... 35

5.6.2 Shaft wiring ............................................................................................................ 37

5.7 Task saving and recovery ................................................................................................... 37

5.7.1 Task saving .............................................................................................................. 37

5.7.2 Task recovery .......................................................................................................... 38

Chapter 6 Document Management .......................................................................................... 40

6.1 Disk .................................................................................................................................... 41

6.2 File ..................................................................................................................................... 41

6.3 Find file .............................................................................................................................. 41

6.4 Code editing ...................................................................................................................... 41

6.5 Delete files......................................................................................................................... 42

6.6 Copy files ........................................................................................................................... 43

6.7 New folder ......................................................................................................................... 43

6.8 Preview .............................................................................................................................. 43

Chapter 7 Parameter Settings ................................................................................................... 45

7.1 Common parameters ........................................................................................................ 45

7.2 Oxygen gas parameter ...................................................................................................... 47

7.2.1 Dynamic perforation and crawling ......................................................................... 49

7.3 Plasma parameter ............................................................................................................. 50

7.4 Powder injection parameters ............................................................................................ 53

7.5 System parameters ............................................................................................................ 54

7.6 Axis parameter .................................................................................................................. 55

7.7 System configuration ......................................................................................................... 56

7.7.1 Input port definition ............................................................................................... 57

7.7.2 Output port definition ............................................................................................ 57

7.7.3 Coordinate definition ............................................................................................. 58

7.7.4 Options ................................................................................................................... 59

7.8 IP settings and THC control ............................................................................................... 61

7.9 Parameter import/ export ................................................................................................. 62

Chapter 8 Diagnostic Functions ............................................................................................... 64

8.1 Input diagnostics ............................................................................................................... 64

8.2 Output diagnostics ............................................................................................................ 64

8.3 Date and time .................................................................................................................... 65

8.4 Manufacturer management .............................................................................................. 65

8.4.1 System Restore, Parameter Backup/Restore .......................................................... 67

8.4.2 Management .......................................................................................................... 67

8.4.3 File cleanup ............................................................................................................ 69

8.5 Rocker calibration .............................................................................................................. 69

User Manual for F7600 Series CNC Cutting System

8.6 Program restart and shutdown ......................................................................................... 70

8.7 Power off ........................................................................................................................... 70

8.8 Restarting shaft card ......................................................................................................... 70

Chapter 9 Graphic Management .............................................................................................. 71

9.1 Select graphics................................................................................................................... 71

9.2 Sheet/ hole size ................................................................................................................. 72

9.3 Chain cutting ..................................................................................................................... 73

9.4 Use nesting software FLCAM ............................................................................................ 73

Chapter 10 Wiring Instructions .................................................................................................. 75

10.1 Input port description ..................................................................................................... 75

10.2 Output Port Description .................................................................................................. 76

10.3 Motor interface description ............................................................................................ 78

10.3.1 Y-axis single drive wiring ...................................................................................... 79

10.3.2 Y-axis double drive wiring .................................................................................... 79

10.4 Power In Description ....................................................................................................... 80

10.5 F7000 and FCB1200PC, F1627D/S wiring instructions .................................................... 80

10.5.1 1 lifting, 1 flame and 1 plasma, or 2 lifting, 1 flame and 2 plasma (Mode 2) ...... 82

10.5.2 4 lifting, 4 plasma, or 2 lifting, 2 plasma (Mode 4) .............................................. 83

10.5.3 2 lifting, 1 flame and 1 plasma, or 3 lifting, 1 flame and 2 plasma (Mode 5) ...... 84

10.5.4 About F1610, F1627D/S wiring instructions ........................................................ 85

10.6 Wiring Instructions for Telecontroller F1510 and F7000 ................................................. 87

10.6.1 Introduction of Telecontroller F1510-T ................................................................ 87

10.6.2 Receiver output .................................................................................................... 88

10.6.3 Remote control configuration of F7000 system ................................................... 88

10.7 Wiring instructions for remote control F1520 and F7000 ............................................... 89

10.7.1 Introduction of Remote Control F1520-T ............................................................. 89

10.7.2 Receiver F1520-R wiring instructions ................................................................... 91

10.7.3 Remote control F1520 and F7000 wiring instructions: ........................................ 92

Chapter 11 Code Specification .................................................................................................. 93

11.1 Programming symbols and instructions .......................................................................... 93

11.2 Coordinate system........................................................................................................... 93

11.3 G code specification ........................................................................................................ 94

11.4 M code description ....................................................................................................... 101

Chapter 12 Height Adjustment Device .................................................................................... 102

12.1 Basic description ........................................................................................................... 102

12.2 Mode of wiring .............................................................................................................. 102

12.3 Height adjustment device configuration ....................................................................... 102

12.4 Height adjustment device initialization connection ...................................................... 103

12.5 Height adjustment device observation window ........................................................... 105

12.6 Height adjustment device parameter interface ............................................................ 106

Chapter 13 Visual Residue ....................................................................................................... 108

13.1 Basic description ........................................................................................................... 108

13.2 Camera installation requirements ................................................................................. 108

13.2.1 Camera selection requirements ......................................................................... 108

User Manual for F7600 Series CNC Cutting System

VII

13.2.2 Camera installation ............................................................................................ 108

13.2.3 Photo request ..................................................................................................... 109

13.2.4 Photo environment ............................................................................................ 109

13.2.5 Accuracy requirement ........................................................................................ 109

13.3 Visual residual calibration ............................................................................................. 109

13.3.1 Visual residual configuration .............................................................................. 109

13.3.2 Visual remnant cloth interface and processing .................................................. 114

Chapter 14 Drilling and Cutting Integrated System ................................................................ 119

14.1 Brief introduction .......................................................................................................... 119

14.2 Interface description ..................................................................................................... 119

14.2.1 Motor control ..................................................................................................... 119

14.2.2 Cylinder control .................................................................................................. 120

14.3 Parameter declaration ................................................................................................... 120

14.4 Instructions for use ....................................................................................................... 123

14.4.1 Code specification .............................................................................................. 123

14.5 Manual operation .......................................................................................................... 124

14.6 Drill axis initial distance setting ..................................................................................... 125

14.7 Graded drilling instructions ........................................................................................... 125

14.8 Cylinder drilling ............................................................................................................. 126

14.9 Drilling timing ................................................................................................................ 127

Appendix 1 Installation Dimensions ............................................................................................. 128

User Manual for F7600 Series CNC Cutting System

Chapter 1 Introduction of F7600 Control System

1.1 Introduction

The F7600 series CNC system absorbs the advantages of many CNC systems at

home and abroad, and with reference to the Company's F2000 series, F3000 series and

F5000 series systems, a CNC system with more complete functions, stronger

performance and more convenient use is developed. The product uses a multi-axis

digital position control method that supports up to 6 axes of linkage, of which 4 axes

have position monitoring. It is suitable for all CNC machine tools that use position

control. Such as oxygen gas, plasma, laser cutting machine tools.

The F7000 controller runs on the Linux real-time operating system. It is equipped

with Cortex-A8 chip and very large programmable device FPGA. The combination of

software and hardware is adopted for interpolation. The Company has been engaged in

numerical control system research for many years. Based on the original trajectory

planning, speed preview and corner control, the S-type acceleration and deceleration

and B-spline interpolation technology of the machine tool have been introduced, which

makes the machine control more stable and the protection mechanism more perfect.

1.2 System Features

 More than 90 standard graphics libraries are integrated.

 Support EIA code and FLCAM, Fastcam, SigmaNest and other nesting software.

Support suffix TXT, CNC, NC, MPG, B3 and other G code formats

 Support ESSI code common instructions

 Support USB standard keyboard and mouse

 Graphic scale, rotation, mirroring, arranging, etc.

 Kerf is added and the original size of the workpiece and the size of the slit are

displayed simultaneously, which makes intuitive and convenient

 Graphic steel plate correction, laser positioning

 Customizable coordinate system supports all eight possibilities for

two-dimensional coordinates

 Edge cutting reduces the warm-up time of thick steel plates

User Manual for F7600 Series CNC Cutting System

 Input and output port functions and port types (normally open and normally closed)

can be customized.

 Oxygen gas, plasma, dusting, demonstration and other modes

 Automatic corner speed limit prevents machine shake effectively

 The starting line and the number of the punch are freely selectable.

 Dynamic/static processing graphic display, graphic enlargement/reduction,

dynamic tracking of cutting points under magnification

 Quick adjustment of commonly used parameters, real-time acceleration and

deceleration in motion, etc.

 Power failure, breakpoint memory protection

 Statistics on processing piece count, running time, number of piercing, etc.

 Support U disk offline upgrade

 Hierarchical management authority facilitates factory management

 System operational statistics and real-time status display

 Support USB mouse and keyboard, touch operation, more humane human

interaction

 Support network data transmission, realize system networking, real-time

monitoring operation (subsequent upgrade support)

 Reserve a variety of communication interfaces including CAN, RS485, RS232, etc.

 Support encoder feedback for finer cuts

 Support gantry bilateral driving algorithm

1.3 Technical indicators

 Number of linkage axles: 2-axis linkage (maximum expandable to 6 axes)

 Control accuracy: ±0.001mm

 Motor drive: pulse + direction

 Impulse frequency: 250K

 Operation speed: 30m/min

 Power supply: DC24V DC power input, power greater than 80W

 Electrostatic test: ±4KV

 Input and output: 16-way input, 16-way output, full optocoupler isolation

 System working environment: temperature -10℃ - +60℃; relative humidity 0-95%

without condensation

User Manual for F7600 Series CNC Cutting System

1.4 F7600 series standard configuration

S/N

Product model

Configuration list

Icon

F7600W-DE (split

machine)

1. Industrial control

computer

2. Motion control card

(Industrial Control Computer) (Motion

Control Card)

F7600W-IN (all-in-one

machine)

1. 19-inch capacitive

touch screen

2. Industrial control

computer

3. Motion control card

(19-inch touch widescreen) (motion

control card)

F7600WF-IN (all-in-one

machine)

- F stands for integrated

front panel and multi-torch

control panel

1. Integrated front

electric cabinet

(including 19" wide

touch screen and

operation panel)

2. Industrial control

computer

3. Motion control card

4. Multi-torch control

board

(integrated front electric cabinet)

(motion control card)

(Multi-torch control board)

Note 1: for F7600W-IN all-in-one machine, industrial computer back hung on the back of 19-inch touch

screen metal case

Note 2: for F7600WF-IN integrated machine, industrial computer is built in integrated front electric cabinet

Note 3: The F7600WF-IN all-in-one machine comes standard with 2 gun control boards. If it is necessary to

control 3-4 guns, expansion board shall be additionally equipped, and the independent control of up to 4

guns is supported

Note 4: for the F7600 full range supports touch screen and mouse operation, but requires a standard

keyboard.

User Manual for F7600 Series CNC Cutting System

1.5 F7600S standard configuration

S/N

Product model

Configuration list

Icon

F7600S-DE (split machine)

1. Industrial control

computer

2. Motion control card

3. Small hole parameter

library

(Industrial Control Computer) (Motion

Control Card)

(Small hole parameter

library)

F7600S-IN (all-in-one

machine)

1.19-inch capacitive touch

screen

2. Industrial control

computer

3. Motion control card

4. Small hole parameter

library

(19-inch touch widescreen) (motion

control card)

(Small hole parameter

library)

F7600SF-IN (all-in-one

machine with integrated

front electric cabinet and

multi-torch control panel)

1. Integrated front electric

cabinet (including 19-inch

wide touch screen and

operation panel)

2. Industrial control

computer

3. Motion control card

4. Multi-torch control

board

5. Small hole parameter

library

(integrated front electric cabinet)

(motion control card)

(Multi-torch control board)

(small hole parameter library)

User Manual for F7600 Series CNC Cutting System

Note 1: for F7600S-IN all-in-one machine, industrial computer back hung on the back of 19-inch touch

screen metal case

Note 2: for F7600SF-IN integrated machine, industrial computer is built in integrated front electric cabinet

Note 3: The F7600SF-IN all-in-one machine comes standard with 2 gun control boards. If it is necessary to

control 3-4 guns, expansion board shall be additionally equipped, and the independent control of up to 4

guns is supported

Note 4: for the F7600 full range supports touch screen and mouse operation, but requires a standard

keyboard.

User Manual for F7600 Series CNC Cutting System

Chapter 2 System Boot

2.1 System startup and main interface description

After the system starts, it will enter the welcome interface, as shown in Figure 2.1.

The pictures in the welcome screen can be upgraded to the user's picture. When the

prompt "Press any key to continue the next step..." appears, press any key and the

system will enter the main interface. The main interface of the F7600 series system is

shown in Figure 2.2.

Figure 2.1 Welcome Interface

Figure 2.2 F7600 Series System Main Interface

In the main interface, press [F1]-[F8] to correspond to the following functions:

User Manual for F7600 Series CNC Cutting System

[1] Graph management: there are dozens of graphic libraries of common parts,

most of which have both chip size and hole size.

[F2] Document management: enter optional hard disk files, USB flash drive files,

find, edit, delete, file import and export, preview graphics and otherwise operate.

[F3] Parts management: mirror image, rotation, plate correction, alignment, line

selection, code editing, etc. for processing parts.

[F4] Parameter settings: all parameters can be set here.

[F5] System diagnosis: input and output diagnosis, date and time settings and

factory management.

[F6] Enlarge the graph: enlarge the cutting graph.

[F7] Manual movement: manually move the machine, in this interface, power-off,

breakpoint recovery operation, and laser gun bias operation can be done.

[F8] Zeroing: after the machine starts cutting money or cutting is completed, the

coordinates can be cleared.

[X]: Set cutting speed.

[Y] Set manual shift speed.

[F] Set the manual shift mode, which can be set to jog, linkage and fixed length.

[G]: Set the moving distance when moving at a fixed length. Description: press G

to modify the fixed length distance number, and the manual transfer mode automatically

switches to the fixed length mode.

[Z]: The slit size can be set before the cutting operation starts or after the cutting is

completed.

[M]: Set the cutting mode. There are three modes: demo mode, oxygen gas cutting

and plasma cutting.

[START]: Start cutting.

[STOP]: Stop cutting.

[Space]: Enter the cutting interface.

User Manual for F7600 Series CNC Cutting System

2.2 Main interface function index

Main

interface

F1 Shape Lib

F4 Setups

Diagnose

F6 Zoom In

F7 Manual

Move

F8 Home

F2 Files

F3 Part

Option

F1 Piece

F2 Hole

Confirm

F1 Disk

F2 File

F3 Search

F4 Edit

File

F5 Ded

File

F6 Copy

F7 Back

F8 Confirm

F1 Start

Point

F2 Angle

F3 Aarray

ScaleMirror

Line\Piece

F6 Code

Edit

F7 Revert

F8 Confirm

F1 Common

F2 Flame

F3 Plasma

F5 System

F6 Config

F7 Import\

Export

F8 Confirm

F1 Input

F2 Output

RockerAdjust

F8 Back

Restart

Reboot

LaserOffset

LaserBack

F7 Back

F2 Param

Recover F3

Passwords

F4 Spray

F3 Chain1

F4 Chain2

F7 Back

F6 Break

Recovery

F8 GoRef

F1 System

F2 Axis

F7 Back

Confirm

F1 Input

F2 Output

Coordomate

Options

F6 IP

F7 Back

Confirm

F3 Clean

File

SysRecover

F7 Back

F8 Update

F4 Decrypt

F5 About

F7 Back

Confirm

F5 Time

VendorManage

ShutDown

PowerOFF

F4 Plasma

Config

TaskSave

TaskLoad

F3 AaxiCopy

Driver

F1 Param

Backup

F5 Manger

F1FLCAM_SE

F6 Restore

F7 Back

F8 Confirm

F2VISON

F1 Un do

F2 Re do

Refresh

F6 Go to

F7 Back

Confirm

F5 allery

configuratio

F3 Corner

Speed

User Manual for F7600 Series CNC Cutting System

Chapter 3 Cutting Function

As shown in Figure 3.1, press the Space button on the main interface to enter the

cutting interface, as shown in Figure 3.2 below:

Figure 3.1 F7600 Series Main Interface

Figure 3.2 Cutting Main Interface

 ○

1 displays the actual cutting path of the currently machined workpiece, including

the kerf value.

 ○

2 displays the status of the strong key, and the corresponding output port can be

User Manual for F7600 Series CNC Cutting System

opened and closed by the touch screen operation. Note: The strong current button

of the F7600 is at the operator panel on the right.

 ○

3 displays the status of the input and output ports used in the current cutting mode,

and the real-time IO timing output.

 ○

4 displays the current real-time machining speed, operating status, and machining

files. During the machining process, fast speed control can be achieved by pressing

[1]-[9]. For example, press the number [3], and the speed is automatically adjusted

to 30%; press the number [8], and the speed is automatically adjusted to 80%. At

the same time, [F4] or [END] can be used to decelerate, [F5] and [HOME] to

accelerate.

 ○

5 displays the current cutting speed, and some parameters used for cutting, as

well as some cutting statistics information. The letters in [] above are shortcut keys,

so pressing them can quickly change the corresponding parameters.

 ○

6 displays the absolute coordinate position of the workpiece where the torch is

currently located.

 ○

7 displays currently executing G code. This status bar is a transparent form,

which can be folded or expanded by the arrow on the right.

 [X] Modify the current cutting speed.

 [Y] Modify the current manual shift speed.

 [F] Change the current manual shift mode.

 [G] Modify the fixed length of the current fixed length movement.

 [Z] Press [Z] to set the kerf value before starting cutting or after cutting.

 [START] Start cutting.

 [STOP] Stop. Pressing it to pause all the actions that are going on in the system.

 [F1] Back: The torch returns along the original path of the track (the I/O port is

closed at this time), and the piercing point will be suspended when it is back.

 [F2] Advance: The torch advances along the cutting path (the I/O port is closed).

 [F3] walking frame or [F3] resetting: before just transferred into the processing file,

and the machine movement, here is the walking frame function, the machine will

walk the torch along the outer contour of the workpiece. After the machine is

moved, here is the resetting function and the machine will return to the zero

coordinate of the workpiece.

User Manual for F7600 Series CNC Cutting System

 [F4] Deceleration: reduce the cutting speed by 3% per press. Reduce manual shift

speed when moving manually.

 [F5] Acceleration: increase the cutting speed by 3% per press. Increase manual

shift speed when moving manually.

 [F6] Preheating decrease: reduce the preheating time, skip the remaining preheat

time, and the system automatically remembers the preheat time.

 [F7] Preheating increase: increase the preheating time by 15 seconds each time

 [F8] Select punching pointing: when the system is paused, the puncturing point is

selected, and after the startup is started, it is dynamical enlargement function.

 Up, down, left and right 4 direction keys: move the cutting gun manually.

User Manual for F7600 Series CNC Cutting System

3.1 Cutting function index

As shown in Figure 3.3, it is the operation index map for the cutting interface.

Cutting

interface

F1 back

F2 forward

F3 walking frame

F4 slowdown

F5 acceleration

F6 preheating

reduction

F7 preheating

increase

F8 select the

piercing point

Figure 3.3 Cutting Operation Index

3.1.1 Normal speed regulation

The speed can be adjusted in the cutting interface system during automatic

operation or when the system is paused.

Press [F5] or [HOME] on the operation panel, and each press will increase the

speed by 3% based on the current speed. Keep pressing [F5] or [HOME] without

releasing, and the speed will continue to increase until the maximum cutting speed.

Press [F4] or [END] on the operation panel, and each press will decrease the

current base by 3%. Press [F4] or [END] without releasing, and the speed will be

continuously reduced to 5% of the maximum cutting speed.

3.1.2 Rapid speed regulation

Rapid speed regulation can be performed on the cutting interface during automatic

operation or when the system is paused.

Page is loading ...

FLCNC F7600 CNC Cutting Controller User manual

Brand: FLCNC

Model: F7600 CNC Cutting Controller

Type: User manual

Download PDF

report

FLCNC F7600 CNC Cutting Controller User manual

FLCNC F7600 CNC Cutting Controller User manual

Related papers

Other documents