Black & Decker ST5530 Owner's manual

Page is loading ...

5

ENGLISH

(Original instructions)

Intended use

Your Black & Decker trimmer has been designed for trimming

and nishing lawn edges and to cut grass in conned spaces.

This appliance is intended for consumer use only.

Safety instructions

Warning!

When using mains-powered

appliances, basic safety precautions,

including the following, should always be

followed to reduce the risk of re, electric

shock, personal injury and material dam-

age.

Warning!

When using the machine

the safety rules must be followed. For

your own safety and bystanders please

read these instructions before operating

the machine. Please keep the instruc-

tions safe for later use.

u

Read all of this manual carefully before

operating the appliance.

u

The intended use is described in this

manual. The use of any accessory

or attachment or the performance

of any operation with this appliance

other than those recommended in this

instruction manual may present a risk

of personal injury.

u

Retain this manual for future refer-

ence.

Using your appliance

Always take care when using the appli-

ance.

u

Always use safety glasses or goggles.

u

Never allow children or people unfa-

miliar with the instructions to use the

appliance.

u

Do not allow children or animals to

come near the work area or to touch

the appliance or power supply cord.

u

Close supervision is necessary when

the appliance is used near children.

u

This appliance is not intended for use

by young or inrm persons without

supervision.

u

This appliance is not to be used as a

toy.

u

Only use the appliance in daylight or

good articial light.

u

Use in a dry location only. Do not allow

the appliance to become wet.

u

Do not immerse the appliance in water.

u

Do not open the body casing. There

are not user-serviceable parts inside.

u

Do not operate the appliance in

explosive atmospheres, such as in the

presence of ammable liquids, gases

or dust.

u

To reduce the risk of damage to plugs

or cords, never pull the cable to re-

move the plug from a socket.

Safety of others

u

This appliance is not intended for use

by persons (including children) with

reduced physical, sensory or mental

capabilities, or lack of experience

and knowledge, unless they have

been given supervision or instruction

concerning use of the appliance by a

person responsible for their safety.

u

Children must be supervised to ensure

that they do not play with the appli-

ance.

6

ENGLISH

(Original instructions)

Residual risks.

Additional residual risks may arise when

using the tool which may not be included

in the enclosed safety warnings. These

risks can arise from misuse, prolonged

use etc.

Even with the application of the relevant

safety regulations and the implementa-

tion of safety devices, certain residual

risks can not be avoided. These include:

u

Injuries caused by touching any rotat-

ing/moving parts.

u

Injuries caused when changing any

parts, blades or accessories.

u

Injuries caused by prolonged use

of a tool. When using any tool for

prolonged periods ensure you take

regular breaks.

u

Impairment of hearing.

u

Health hazards caused by breathing

dust developed when using your tool

(example:- working with wood, espe-

cially oak, beech and MDF.)

After use

u

When not in use, the appliance should

be stored in a dry, well ventilated place

out of reach of children.

u

Children should not have access to

stored appliances.

u

When the appliance is stored or trans-

ported in a vehicle it should be placed

in the boot or restrained to prevent

movement following sudden changes

in speed or direction.

Inspection and repairs

u

Before use, check the appliance for

damaged or defective parts. Check for

breakage of parts and any other condi-

tions that may affect its operation.

u

Do not use the appliance if any part is

damaged or defective.

u

Have any damaged or defective parts

repaired or replaced by an authorised

repair agent.

u

Never attempt to remove or replace

any parts other than those specied in

this manual.

Additional safety instruc-

tions for grass trimmers

Warning!

Cutting elements continue

to rotate after the motor is switched off.

u

Be familiar with the controls and the

proper use of the appliance.

u

Before use, check the power supply

cord and extension cord for signs of

damage, ageing and wear. If a cord

becomes damaged during use, discon-

nect the cord from the mains supply

immediately. DO NOT TOUCH THE

CORD BEFORE DISCONNECTING

THE SUPPLY.

u

Do not use the appliance if the cords

are damaged or worn.

u

Wear stout shoes or boots to protect

your feet.

u

Wear long trousers to protect your

legs.

u

Before using the appliance, check that

your cutting path is free from sticks,

stones, wire and any other obstacles.

7

ENGLISH

(Original instructions)

u

Only use the appliance in the upright

position, with the cutting line near the

ground. Never switch the appliance on

in any other position.

u

Move slowly when using the appliance.

Be aware that freshly cut grass is

damp and slippery.

u

Do not work on steep slopes. Work

across the face of slopes, not up and

down.

u

Never cross gravel paths or roads

while the appliance is running.

u

Never touch the cutting line while the

appliance is running.

u

Do not put the appliance down until the

cutting line has come to a complete

standstill.

u

Use only the appropriate type of cut-

ting line. Never use metal cutting line

or shing line.

u

Be careful not to touch the line trim-

ming blade.

u

Take care to keep the mains cable

away from the cutting line. Always be

aware of the position of the cable.

u

Keep hands and feet away from the

cutting line at all times, especially

when switching on the motor.

u

Before using the appliance and after

any impact, check for signs of wear or

damage and repair as necessary.

u

Never operate the appliance with

damaged guards or without guards in

place.

u

Take care against injury from any de-

vice tted for trimming the lament line

length. After extending new cutter line

always return the machine to its nor-

mal operating position before switching

on.

u

Always ensure that the ventilation slots

are kept clear of debris.

u

Do not use the lawn trimmer (edge

trimmer), if the cords are damaged or

worn.

u

Keep extension cords away from cut-

ting elements.

Electrical safety

#

This appliance is double insu-

lated; therefore no earth wire is

required. Always check that the

power supply corresponds to the

voltage on the rating plate.

u

If the supply cord is damaged, it must

be replaced by the manufacturer or

an authorised Black & Decker Service

Centre in order to avoid a hazard.

u

Electric safety can be further improved

by using a highsensitivity 30 mA Re-

sidual Current Device (RCD).

Labels on appliance

The following warning symbols are found on the appliance:

Read the manual prior to operation.

Wear safety glasses or goggles when operating

this appliance.

8

ENGLISH

(Original instructions)

N

Wear suitable ear protectors when operating this

appliance.

E

Always remove the plug from the socket before

inspecting a damaged cable. Be careful not to

use your strimmer if the cable is damaged.

K

Beware of ying objects. Keep bystanders away

from the cutting area.

R

Do not expose the appliance to rain or high

humidity.

Directive 2000/14/EC guaranteed sound power.

Features

This appliance includes some or all of the following features.

1. On/off switch

2. Handle

3. Cable restraint

4. Power inlet

5. Second handle

6. Guard

7. Spool housing

8. Head

9. Edge wheel (ST5530 Only)

10. Edge guide (ST4525 Only)

Assembly

Warning! Before assembly, make sure that the tool is

switched off and unplugged.

Fitting the guard (g. A & B)

u Remove the screw from the guard.

u Keeping the guard (6) square to the strimmer head (8)

slide it into place until the retaining tab clicks into place

(Ensure that the guide rails (11) on the guard (6) are

correctly aligned with the guide rails (12) on the strimmer

head (8). g. A).

u Secure the guard (6) with the screw (13).

Warning! Never use the tool unless the guard is properly

tted.

Attaching the second handle (g. C)

u Press in and hold both of the buttons (14) on the side of

the handle.

u Slide the second handle (5) in place over the buttons (14).

Warning! Ensure that the teeth on the button are correctly

aligned in slots in the handle and that the handle is secure.

Adjusting the position of the secondary handle (g.

D)

The second handle (5) can be adjusted to provide optimum

balance and comfort.

u Press in the button (14) on the left side of the handle.

u Rotate the second handle (5) into the required position.

u Release the button (14).

Warning! Ensure that the teeth on the button are correctly

aligned in slots in the handle and that the handle is secure.

Adjusting the height of the tool (g. E)

This tool has a telescopic mechanism, allowing you to set it to

a comfortable height. There are multiple height settings.

To adjust the height setting, proceed as follows:

u Disconnect the tool from the supply.

u Loosen the adjustment collar (15) by turning it clockwise.

u Gently pull the tube (16) in or out of the handle (2) to the

desired height.

u Tighten the adjustment collar (15) by turning anti-clock-

wise.

Releasing the cutting line

In transit, the cutting line is taped to the spool housing.

Warning! Before assembly, disconnect from the power supply

u Remove the tape holding the cutting line to the spool

housing (7).

Connecting the tool to the mains (g. F)

u Connect the female plug of a suitable extension cable to

the power inlet (4).

u Loop the cable through the cable restraint (3).

u Insert the mains plug into a mains outlet.

For wired in cable units: Make sure the cable is looped

through the cable restraint prior to connecting the plug to the

mains outlet.

Use

Warning! Let the tool work at its own pace. Do not overload.

Setting the tool to trimming or edging mode (g. G,

H, I & J)

The tool can be used in trimming mode as shown in g. I or in

edging mode to trim overhanging grass along lawn edges and

ower beds as shown in g. J.

Trimming mode (g. E, G & I)

For trimming, the trimmer head should be in the position

shown in g. I. If it is not:

u Disconnect the tool from the supply.

u Loosen the adjustment collar (15) by turning it clockwise.

u Whilst holding the handle (2), rotate the head (8) clock-

wise.

u Tighten the collar (15) by turning it anti-clockwise.

Note: Note: The head will only rotate in one direction.

Edging mode (g. E, H & J)

For edging, the trimmer head should be in the position shown

in g. J. If it is not:

9

ENGLISH

(Original instructions)

u Disconnect the tool from the supply.

u Loosen the adjustment collar (15) by turning it clockwise.

u Whilst holding the handle (2), rotate the head (8) anti-

clockwise.

u Tighten the collar (15) by turning it anti-clockwise.

Note: The head will only rotate in one direction.

Switching on and off

u To switch the tool on, squeeze the trigger lever (1).

u To switch the tool off, release the trigger lever.

Warning! Never attempt to lock the trigger lever in the on

position.

Hints for optimum use

General

u In order to achieve optimum cutting results, only cut dry

grass.

Trimming

u Hold the tool as shown in g. I.

u Gently swing the trimmer from side to side.

u When cutting long grass, work in stages from the top. Take

small cuts.

u Keep the tool away from hard objects and delicate plants.

u Cutting line will wear faster and require more feeding if

the cutting is done along pavements or other abrasive

surfaces or heavier weeds are being cut.

u If the tool starts running slowly, reduce the load.

Edging

Optimum cutting results are achieved on edges deeper than

50 mm.

u Do not use the tool to create edges. To create edges,

use an edging spade.

u Guide the tool on its wheel (9) or edge guide (10) as

shown in g. J.

u To make a closer cut, slightly tilt the tool.

Fitting a new spool of cutting line (g. K)

Replacement spools of cutting line are available from your

Black & Decker dealer (cat. no. A6481).

u Unplug the tool.

u Keep the tabs (17) depressed and remove the spool cover

(18) from the spool housing (7).

u Remove the empty spool (19) from the spool housing.

u Remove any dirt and grass from the spool cover and

housing.

u Take the new spool and push it onto the boss in the spool

housing. Rotate the spool slightly until it is seated.

u Unclip the end of the cutting line and guide the line into

the eyelet (20). The line should protrude approx. 11 cm

from the spool housing.

u Align the tabs (17) on the spool cover with the cut outs

(21) in the spool housing.

u Push the cover onto the spool housing until it snaps

securely into place.

Warning! If the cutting lines protrude beyond the trimming

blade (22), cut them off so that they just reach the blade.

Winding new line onto an empty spool (g. L, M &

N)

You may wind new cutting line onto an empty spool.

Replacement packs of cutting line are available from your

Black & Decker dealer (cat. no. A6170 (25 m), A6171 (40 m)).

u Remove the empty spool from the tool as described

above.

u Remove any remaining cutting line from the spool.

u Feed 2 cm of cutting line into the hole (23) in the spool as

shown (g. L).

u Bend the cutting line and anchor it in the L-shaped slot

(24).

u Wind the cutting line onto the spool in the direction of the

arrow. Make sure to wind the line on neatly and in layers.

Do not criss-cross (g. N).

u When the wound cutting line reaches the recesses (25),

cut the line. Let the line protrude approx. 11 cm from the

spool and hold a nger on the line to keep it in place (g.

M).

u Proceed as described above to t the spool on the tool.

Warning! Only use the appropriate type of Black & Decker

cutting line.

Troubleshooting

If your tool seems not to operate properly, follow the instruc-

tions below. If this does not solve the problem, please contact

your local Black & Decker repair agent.

Warning! Before proceeding, unplug the tool.

Appliance runs slowly

u Check that the spool housing can rotate freely. Carefully

clean it if necessary.

u Check that the cutting line does not protrude more than

11 cm from the spool housing. If it does, cut it off so that it

just reaches the line trimming blade.

Automatic line feed does not work

u Keep the tabs depressed and remove the spool cover

from the housing.

u Pull the cutting line until it protrudes 11 cm from the hous-

ing. If insufcient cutting line is left on the spool, install a

new spool of cutting line as instructed above.

u Align the tabs on the spool cover with the cut outs in the

housing.

u Push the cover onto the housing until it snaps securely

into place.

u If the cutting line protrudes beyond the trimming blade, cut

it off so that it just reaches the blade.

If the automatic line feed still does not work or the

spool is jammed, try the following suggestions:

u Carefully clean the spool cover and housing.

10

ENGLISH

(Original instructions)

u Remove the spool and check if the lever can move freely.

u Remove the spool and unwind the cutting line, then wind it

on neatly again as described above. Replace the spool as

instructed.

Maintenance

Your Black & Decker corded/cordless appliance/tool has been

designed to operate over a long period of time with a minimum

of maintenance. Continuous satisfactory operation depends

upon proper tool/appliance care and regular cleaning.

Your charger does not require any maintenance apart from

regular cleaning.

Warning! Before performing any maintenance on corded/

cordless power tools:

u Switch off and unplug the appliance/tool.

u Or switch off and remove the battery from the appliance/

tool if the appliance/tool has a separate battery pack.

u Or run the battery down completely if it is integral and then

switch off.

u Unplug the charger before cleaning it. Your charger does

not require any maintenance apart from regular cleaning.

u Regularly clean the ventilation slots in your tool/appliance

and charger using a soft brush or dry cloth.

u Regularly clean the motor housing using a damp cloth. Do

not use any abrasive or solvent-based cleaner.

u Regularly clean the cutting line and spool using a soft

brush or dry cloth.

u Regularly use a blunt scraper to remove grass and dirt

from the underneath of the guard.

Protecting the environment

Z

Separate collection. This product must not be

disposed of with normal household waste.

Should you nd one day that your Black & Decker product

needs replacement, or if it is of no further use to you, do not

dispose of it with household waste. Make this product avail-

able for separate collection.

z

Separate collection of used products and packag-

ing allows materials to be recycled and used again.

Re-use of recycled materials helps prevent

environmental pollution and reduces the demand

for raw materials.

Local regulations may provide for separate collection of elec-

trical products from the household, at municipal waste sites or

by the retailer when you purchase a new product.

Black & Decker provides a facility for the collection and

recycling of Black & Decker products once they have reached

the end of their working life. To take advantage of this service

please return your product to any authorised repair agent who

will collect them on our behalf.

You can check the location of your nearest authorised repair

agent by contacting your local Black & Decker ofce at

the address indicated in this manual. Alternatively, a list of

authorised Black & Decker repair agents and full details of our

after-sales service and contacts are available on the Internet

at: www.2helpU.com

Technical data

ST4525

Type 1

ST5530

Type 1

Input Voltage

V

AC

230 230

Power Input

W

450 550

No-Load Speed

min

-1

7300 7500

Weight

kg

2.5 2.5

Hand/arm weighted vibration value according to EN 786:

= 3.8 m/s

2

, uncertainty (K) = 1.5 m/s

2

.

L

PA

(sound preasure) 80 dB(A)

uncertainty (K) = 1 dB(A)

11

ENGLISH

(Original instructions)

EC declaration of conformity

MACHINERY DIRECTIVE

OUTDOOR NOISE DIRECTIVE

%

ST4525/ST5530

Black & Decker declares that these products described under

"technical data" are in compliance with:

2006/42/EC, EN 60335-1, EN 60335-2-91

2000/14/EC, Lawn Trimmer, L ≤ 50 cm, Annex VIII

DEKRA Certication B.V., Utrechtseweg 310,

6802 ED Arnhem, The Netherlands

Notied Body ID No.: 0344

Level of accoustic power according to 2000/14/EC

(Article 12, Annex III, L ≤ 50 cm):

L

WA

(measured sound power) 94 dB(A)

uncertainty (K) = 1 dB(A)

L

WA

(guaranteed sound power) 95 dB(A)

These products also comply with Directive 2004/108/EC and

2011/65/EU.

For more information, please contact Black & Decker at the

following address or refer to the back of the manual.

The undersigned is responsible for compilation of the technical

le and makes this declaration on behalf of Black & Decker.

_

Kevin Hewitt

Vice-President Global Engineering

Black & Decker Europe, 210 Bath Road, Slough,

Berkshire, SL1 3YD

United Kingdom

27/09/2013

Guarantee

Black & Decker is condent of the quality of its products and

offers an outstanding guarantee. This guarantee statement is

in addition to and in no way prejudices your statutory rights.

The guarantee is valid within the territories of the Member

States of the European Union and the European Free Trade

Area.

If a Black & Decker product becomes defective due to faulty

materials, workmanship or lack of conformity, within 24 months

from the date of purchase, Black & Decker guarantees to

replace defective parts, repair products subjected to fair

wear and tear or replace such products to ensure minimum

inconvenience to the customer unless:

u The product has been used for trade, professional or hire

purposes;

u The product has been subjected to misuse or neglect;

u The product has sustained damage through foreign

objects, substances or accidents;

u Repairs have been attempted by persons other than

authorised repair agents or Black & Decker service staff.

To claim on the guarantee, you will need to submit proof of

purchase to the seller or an authorised repair agent. You can

check the location of your nearest authorised repair agent by

contacting your local Black & Decker ofce at the address indi-

cated in this manual. Alternatively, a list of authorised Black &

Decker repair agents and full details of our after-sales service

and contacts are available on the Internet at: www.2helpU.com

Please visit our website www.blackanddecker.co.uk to register

your new Black & Decker product and to be kept up to date

on new products and special offers. Further information on the

Black & Decker brand and our range of products is available

at www.blackanddecker.co.uk

Do not forget to register your product!

www.blackanddecker.co.uk/productregistration Register

your product online at www.blackanddecker.co.uk/produc-

tregistration or send your name,surname and product code

to Black & Decker in your country.

Page is loading ...

Black & Decker ST5530 Owner's manual

This manual is also suitable for

Black & Decker ST5530 Owner's manual

in other languages

Related papers

Other documents