EP2C612D8 / EP2C612D8-8R / EP2C612D8-2T8R
Quick Installation Guide
www.asrockrack.com
No. Description No. Description
1 Serial Port (COM1) 5 USB 3.0 Ports (USB3_1-2)
2 VGA Port (VGA1) 6
EP2C612D8 / EP2C612D8-8R:
1G LAN RJ-45 Port (LAN1)
EP2C612D8-2T8R:
10G LAN RJ-45 Port (LAN1)
3 USB 2.0 Ports (USB_1-2) 7
EP2C612D8 / EP2C612D8-8R:
1G LAN RJ-45 Port (LAN2)
EP2C612D8-2T8R:
10G LAN RJ-45 Port (LAN2)
4 LAN RJ-45 Port (IPMI_LAN)
4
2
P/N: 15G065024100AK V1.0
Install the Server Board
Motherboard Layout
Jumper Cap On/O
The server board User's Manual is available for download from the ASRock Rack's ofcial website
at http://www.asrockrack.com.
Take note of the following precautions before you install server board components or change any
server board settings.
1. Unplug the power cord from the wall socket before touching any components.
2. To avoid damaging the server board’s components due to static electricity, NEVER place your
server board directly on the carpet or the like. Also remember to use a grounded wrist strap or
touch a safety grounded object before you handle the components.
3. Hold components by the edges and do not touch the ICs.
4. Whenever you uninstall any component, place it on a grounded anti-static pad or in the bag
that comes with the component.
5. When placing screws into the screw holes to secure the server board to the chassis, please do
not over-tighten the screws! Doing so may damage the server board.
1
1
Insert the server board into the chassis.
2
Af fi x the screws clockw ise into the
mounting holes in all of the corners of
the server board.
Do not over-tighten the screws
When the jumper cap is placed on the pins, the
jumper is “Short”. If no jumper cap is placed on the
pins, the jumper is “Open”.
The illustration shows a 3-pin jumper whose pin1
and pin2 are “Short” when a jumper cap is placed on
these 2 pins.
I/O Panel
24.4cm (9.6 in)
25.4cm (10.0 in)
ATXPWR1
1
PCIE2
VGA1
COM1
LAN1
LAN2
USB3_2_3
DDR4_D (64 bit, 288-pin module)
DDR4_C (64 bit, 288-pin module)
DDR4_F (64 bit, 288-pin module)
DDR4_E (64 bit, 288-pin module)
DDR4_A (64 bit, 2 88-pin module)
DDR4_B (64 bit, 288-pin module)
DDR4_G (64 bit, 288-pin module)
DDR4_H (64 bit, 288-pin module)
USB 2.0
T: USB_2
B: USB_1
PCIE6
PCIE4
1
PSU_SMB1
1
1
IPMB_1
1
CMOS
Battery
RoHS
BMC_SMB_3
2
1
EP2C612D8-2T8R
USB 3.0
T: USB3_2
B: USB3_1
Top:
IMPI_LAN
USB3_5
1
1
1
AUX_PANEL1 PANEL1
TPM1
BMC_SMB_2
BMC_SMB_1
1
1
1
1
BMC
ROM
64Mb
BIOS
Intel
C612
LSI
3008
Intel
X540
BMC
AST2400
64Mb
BIOS
4
5
6
7
1
1
REAR_FAN1
SPEAKER1
SATA_4
SATA_5
SATA_2
SATA_3
SATA_0
SATA_1
SCU_0
SCU_3
SCU_2
SCU_1
FRNT_FAN1
SATA_SGPIO2
SATA_SGPIO1
FRNT_FAN2
FRNT_FAN4
CPU1_FAN
FRNT_FAN3
CPU2_FAN
8
9
10
11
12
13
14
15
17
2122232425272829293031
32
34
36 33353738394041
42
43
44
45
47
48
3
ATX12V3
ATX12V2
CPU1
CPU2
(NCSI)
(Blue, from CPU1)
(White, from CPU2)
(Blue, from CPU1)
NMI_BTN1
PECI_SEL1
J100
PMBUS_CLK_SEL
1
1
1
CHASSIS_ID0_1
CHASSIS_ID0_2
CHASSIS_ID0_3
18
19
1
PMBUS_DATA_SEL
PMBUS_ALT_SEL
ME_RECOVERY1
20
46
LSI_SAS_0_7
16
No. Description
1
2 x 288-pin DDR4 DIMM Slots
(DDR4_G, DDR4_H, Blue)
2 ATX 12V Power Connector (ATX12V3)
3 PSU SMBus (PSU_SMB1)
4 ATX Power Connector (ATXPWR1)
5 ATX 12V Power Connector (ATX12V2)
6
2 x 288-pin DDR4 DIMM Slots
(DDR4_A, DDR4_B, Blue)
7 Front Fan Connector (FRONT_FAN3)
8 CPU1 Fan Connector (CPU1_FAN)
9
2 x 288-pin DDR4 DIMM Slots
(DDR4_C, DDR4_D, Blue)
10 Front Fan Connector (FRONT_FAN4)
11 Front Fan Connector (FRONT_FAN2)
12 SATA SGPIO Connector (SATA_SGPIO1)
13 SATA SGPIO Connector (SATA_SGPIO2)
14 USB 3.0 Header (USB3_2_3)
15
Mini SAS HD Connector (LSI_SAS_0_7)*
*For EP2C612D8-8R / EP2C612D8-2T8R only
16 Chassis ID2 Jumper (Chassis_ ID0_2)
17 Chassis ID3 Jumper (Chassis_ ID0_3)
18 Chassis ID1 Jumper (Chassis_ ID0_1)
19 SCU Connector (SCU_1), White
20 Front Fan Connector (FRONT_FAN1)
21 SCU Connector (SCU_0), White
22 SCU Connector (SCU_2), White
23 SCU Connector (SCU_3), White
24 SATA3 Connector (SATA_1), White
25 SATA3 Connector (SATA_0), White
26 SATA3 Connector (SATA_3), White
27 SATA3 Connector (SATA_2), White
28 SATA3 Connector (SATA_5), White
29 SATA3 Connector (SATA_4), White
30 Vertical Type A USB 3.0 (USB3_5)
31 System Panel Header (PANEL1)
32 Speaker Header (SPEAKER1)
33 Auxiliary Panel Header (AUX_PANEL1)
34 ME Recovery Jumper (ME_RECOVERY1)
35 CPU PECI Mode Jumper (PECI_SEL1)
36 Descriptor Security Override Jumper (J100)
37 PMBUS Mode Jumper (PMBUS_SEL_DAT1)
38 TPM Header (TPM1)
39 PMBUS Mode Jumper (PMBUS_SEL_ALT1)
40 BMC SMBus Header (BMC_SMB_3)
41 Rear Fan Connector (REAR_FAN1)
42 BMC SMBus Header (BMC_SMB_2)
43 BMC SMBus Header (BMC_SMB_1)
44 PMBUS Mode Jumper (PMBUS_SEL_CLK1)
45
Intelligent Platform Management Bus Header
(IPMB _1)
46 Non Maskable Interrupt Button (NMI_BTN1)
47
2 x 288-pin DDR4 DIMM Slots
(DDR4_E, DDR4_F, Blue)
48 CPU 2 Fan Connector (CPU2_FAN)
2
3
4
1
5
7
6
*15G065024100AK*
Note:
EP2C612D8-2T8R: Intel X540
EP2C612D8 / EP2C612D8-8R: Intel I350
(See Note)
3
EP2C612D8 / EP2C612D8-8R / EP2C612D8-2T8R
Quick Installation Guide
www.asrockrack.com
1G For EP2C612D8-8R / EP2C612D8
Speed LED Activity / Link LED
Status Description Status Description
O 10Mbps connection or
no link
O No link
Yel low 100Mbps connection Blinking Green Data Activity
Green 1Gbps connection On Link
10G For EP2C612D8-2T8R
Speed LED Activity / Link LED
Status Description Status Description
O 100Mbps connection or
no link
O No link
Yel low 1Gbps connection Blinking Green Data Activity
Green 10Gbps connection On Link
Activity / Link LED Speed LED
Status Description Status Description
O No Link O 10M bps connection or no
link
Blinking Yellow Data Activity Yel low 100M bps connection
On Link Green 1G bps connection
8 LAN Port LED Indications
Recommended Memory Congurations
ACT/LINK LED
SPEED LED
LAN Port
5
7
9
6
1
2
3
Open the socket levers and the
CPU socket cover.
Install the processor and close
the socket cover.
Close the socket levers. Remove
the CPU protection cap.
Install the CPU Fan and Heatsink
CPU_
FAN
1
2
Apply the thermal grease. Install the
CPU fan and heatsink and secure
the screws.
Connect the CPU fan to the CPU
FAN connector.
Install the Memory
Install the Power Cables
1
2
3
Unlock a DIMM slot by
pressing the module clips
outward.
Insert the memory module. Lock the clips.
11
Install the PCIE Card
1
Remove the bracket facing the slot that
you intend to use. Keep the screw for
later use.
2
Align t he card con nector w ith t he
slot and press firmly until the card is
completely seated on the slot.
Fasten the card to the chassis with the
screw.
3
A
B
B
A
A
B
A
B
A
B
IPMI LAN Port
1G/10G LAN Port
System Panel Header Auxiliary Panel Header
12
Headers
GND
RESET#
PWRBTN#
PLED-
PLED+
GND
HDLED-
HDLED+
1
GND
10
Install the Processor
4
8
1
5
+12V2
GND
4
8
1
5
+12V2
GND
ACT/LINK LED
SPEED LED
LAN Port
A single memory module should be installed in the BLUE socket.
If you install only one CPU (CPU1) on the motherboard, make sure to install DIMMs into DDR4_A,
DDR4_B, DDR4_C, or DDR4_D slot(s).
1 CPU Conguration
CPU1
A B C D
1 DIMM
#
2 DIMMS
# #
4 DIMMS
# # # #
*e # mark indicates the slot is populated.
2 CPU Conguration
CPU1 CPU2
A B C D E F G H
1 DIMM
#
2 DIMMS
# #
4 DIMMS
# # # #
8 DIMMS
# # # # # # # #
GND
SMB_ CL K
SMB_ Al ert
CASE OP EN
1
SMB_ DA TA
+3VS B
LAN1 _L INK
LED_ PW R
LAN2 _L INK
LED_ PW R
+5VS B
GND
GND
LOCAT O RLED1+
LOCAT O RLED1-
LOCATO RBTN#
LOCAT O RLED2+
LOCATO RLED2-
A
B
C
D
1
3V
3V
GND
GND
5V
5V
GND
PWROK_PS
5VSB
12V
12V
3V
3V
-12V
GND
PSON#
GND
GND
GND
5V
5V
5V
GND
N/A
12
24 13
We recommend using the CPU Installation tool to avoid CPU pin-bent problem.
-
1
-
2
ASRock Rack EP2C612D8-8R Quick Installation Manual
- Type
- Quick Installation Manual
- This manual is also suitable for
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
ASRock Rack EP2C612D8-2T8R Installation guide
-
-
-
-
-
-
-
-
-
Other documents
-
ASROCK E3C226D2I User manual
-
-
-
-
-
ASROCK EP2C602-2TS6/D16 User manual
-
-
-
-