Astonica 50100765 User manual

Brand: Astonica

Model: 50100765

Type: User manual

For warranty information, please refer to the back page of

this instruction manual.

270809rev1

Read the instructions and precautions before use of this product

Please keep this instruction manual for future reference

Limited Warranty

World Factory Inc Products for Home Use

World Factory, Inc. (Seller) warrants to the original Buyer only, that each Astonica Product will be free

from defects in material and workmanship for a period of one (1) year from date of purchase.

SELLER

WARRANTY SHALL BE THE REPAIR OR REPLACEMENT OF PARTS WITHOUT CHARGE WHICH

ARE DEFECTIVE IN MATERIAL OR WORKMANSHIP ANY PARTS AS DETERMINED BY THE

SELLER WHICH HAVE BEEN MISUSED; ABUSED OR DAMAGED EITHER DIRECTLY OR INDIRECTLY

FROM REPAIRS OR ALTERATIONS ATTEMPTED BY UNAUTHORIZED PERSONS; IMPROPER

MAINTENANCE, NEGLECT OR ACCIDENT ARE NOT COVERED BY THIS LIMITED WARRANTY. This

warranty does not apply to damage, heat-induced coloration changes, scratching or alteration due to

normal use or weathering. To make a claim under this Limited Warranty, you must return the complete

product with proof of purchase, transportation prepaid, to any World Factory, Inc. authorized service

center. Call 1-888-424-3354 for the location of the nearest authorized service center.

Additional Limitations

THIS LIMITED WARRANTY DOES NOT APPLY TO ACCESSORY OR CONSUMABLE ITEMS RELATED

TO THIS PRODUCT. ALL IMPLIED WARRANTIES SHALL BE LIMITED IN DURATION TO ONE (1)

YEAR FROM DATE OF PURCHASE. IN NO EVENT SHALL SELLER BE LIABLE FOR ANY

INCIDENTAL OR CONSEQUENTIAL DAMAGES, INCLUDING BUT NOT LIMITED TO LIABILITY FOR

LOSS OF PROFITS, ARISING FROM THE SALE OR USE OF THIS PRODUCT.

If any provision of this Limited Warranty is for any reason held to be invalid or unenforceable, such

provision shall not affect any other provision herein, this Limited Warranty shall be construed as if

such invalid and/or unenforceable provision had never been contained herein.

This Warranty contains the entire agreement between Seller and Buyer and supersedes any and all

prior agreements, arrangements, or understandings between the parties relating to product warranty.

Made in China

Distributed by

World Factory Inc

Irving TX 75063

Model No 50100765

Stone Ridge Swivel Rocker

Instruction Manual

Due to ongoing product development

the actual product or products may vary from

the illustrations or photos shown within this manual.

NOTE: This product is intended for residential, non-commercial use.

"U" BAR

WASHER

BOLT

METAL PLATE

SPRING WASHER

NUT

FOOT CAP

STEEL SPRING PLATE

ROCKER ASSEMBLY

SWIVEL BASE

PARTS LIST

ITEM DESCRIPTION QUANTITY

Carefully remove the contents from the package If any parts are missing do not

attempt to use the product until they have been obtained and correctly installed

ASSEMBLY INSTRUCTIONS

A Chair Frame 1

B Swivel Base & Rocker Assembly 1

C 5/16 X25MM Bolt 4

D 8.5X2.0MM Spring Washer 4

E 4

F 5/16 Nut

G Metal plate

H Hex Wrench-1

I Hex Wrench-2

NOTE This product is intended for residential non commercial use

Parts Detail

Figure 1

8.5X1.5MM Washer

Step 1: Identify all parts packed in carton against the parts list. Remove all protective materials.

Place parts on a non-abrasive surface to avoid scratching.

Step 2: Place the swivel base (with rocker assembly) on a flat, solid surface. Make sure the

rocker assembly is positioned all the way into the base. It may have shifted or vibrated

out during shipment.

Step 3: Important: We recommend 2 people work together to assemble the chair. Note the

arrow labels on the "U" bar and the rocker assembly. Also note the horseshoe shape of

the rocker plate. Point the open end of the horseshoe away from you. The arrows on

the rocker assembly should be pointing towards you. Set the chair frame on the rocker

assembly with front of the seat facing you and the arrows on the "U" bar pointing

towards you ( See diagram). This is very important for a safe, balanced rocking motion.

If chair frame has been properly positioned on the rocker assembly, all arrows on

the "U" bar and rocker assembly will be pointing in the same direction.

Step 4: Critical Step: The two metal plates must be installed in the proper location. Read this

step and carefully examine the diagram. Guide the bolts and washer through the holes in

the "U" bar, through the holes in the steel spring plate, through the hole in the metal plate,

beneath the steel spring plate, add a spring washer and a nut to each bolt as shown in the

diagram. Hand tighten nuts 3-4 revolutions only. Repeat the same procedure on the

other side.

CAUTION: Failure to place metal plates under the rocker plates and above the "U"

bar exactly as shown in diagram will cause the bolt heads and nuts to damage the

structure of the rocker plates and the "U" bar. Damage due to over tightening of

bolts or improper assembly could cause injury and may void your warranty.

Step 5: Tighten all nuts and bolts with the hex wrenches provided. Do not over tighten.

Remove arrow labels from "U" bar and rocker assembly.

Step 6: Your chair should be ready for use. If your chair is not rocking properly, double-check

your assembly procedure, especially Step 3. If the chair rocks too far forward to or is

difficult to rock backwards, you have probably installed the seat frame backwards on the

rocker assembly. If you need further assistance.

Astonica 50100765 User manual

Astonica 50100765 User manual

Astonica 50100765 User manual

Related papers

Other documents