Aerus HF 300 Operating instructions

Brand: Aerus

Model: HF 300

Type: Operating instructions

Aerus HF 300 is a non-electric whole house filtration system. It is designed to remove impurities from water, including sediment, chlorine, and heavy metals. The HF 300 can be used in a variety of applications, including residential, commercial, and industrial.

Some of the benefits of using the HF 300 include:

Improved water quality
Reduced water consumption
Longer lasting appliances
Healthier skin and hair

The HF 300 is easy to install and maintain. It comes with a 10-year warranty.

Some of the benefits of using the HF 300 include:

Improved water quality
Reduced water consumption
Longer lasting appliances
Healthier skin and hair

The HF 300 is easy to install and maintain. It comes with a 10-year warranty.

Operation Manual

HF 300 • NON-ELECTRIC WHOLE HOUSE FILTRATION SYSTEM

HF 300

Installation Guide

CAUTION:

Do not use systems on untreated well water that

is microbiologically unsafe.

 Do not exceed 125 psi water pressure.

 Do not exceed 110F water temperature.

 Do not subject unit to freezing conditions.

All plumbing must be in compliance with local

and state plumbing codes.

STEP 1

Determine a suitable location for the HF 300 water

filtration system. The chosen location should provide

you adequate access to service the water filter. Ensure

that the location is beyond the main water supply

control valve with access to the water lines that feed

the home.

STEP 2 (Important)

Place the HF 300 in position and slowly fill the tank using

a sanitary water source, such as a hose, until the tank is

3/4 filled with water to “wet” or soak the media.

INSTALLATION (Follow Steps 1 - 14)

Do this first upon arrival

STEP 4

Release water pressure by opening faucets at the

kitchen sink.

HF 300

Installation Guide

STEP 5

NOTE: 1” and 3/4” quick connect fittings are provided.

• Install fittings on the by-pass by removing the red

locking clip(s).

• Lubricate the o-ring on the quick connect fitting

before inserting into the by-pass.

• Return the red locking clip(s) to secure the fitting.

STEP 6

Make the necessary plumbing connections to the incoming

water supply line.

NOTE: Look for arrow modeled into the valve body for flow

direction, pointing into the valve is IN.

CAUTION: Allow time for glued connections to cure before proceeding.

Fig. 3

Fig. 4

STEP 3

Shut off the main water supply valve to the home.

By-pass valve

Note directional arrow for water flow

STEP 7

Turn the by-pass valves to the “OFF” position (red valves)

pointing “across” the valve (as shown).

HF 300

Installation Guide

STEP 8

With the faucet still on, open the main water supply valve.

STEP 9 CAUTION: Inspect all plumbing connections. Check for leaks and make repairs as needed.

STEP 10

Open the outlet side of the bypass (Fig. 6).

STEP 11

Slowly open the inlet of the by-pass valve a ¼ turn at a time.

STEP 12

With water flowing at the faucet continue to slowly

open the inlet valve until it is completely open.

STEP 13 (Important)

Leave the faucet open for a minimum of five to ten minutes after

the water runs clear. This last step will flush loose particles from

the carbon filter.

STEP 14 System is ready for service. Check for leaks and

repair as needed.

OUT

Fig. 6

OUTLET

INLET

By-Pass Valve

Aerus HF 300 Operating instructions

Brand: Aerus

Model: HF 300

Type: Operating instructions

Some of the benefits of using the HF 300 include:

Improved water quality
Reduced water consumption
Longer lasting appliances
Healthier skin and hair

The HF 300 is easy to install and maintain. It comes with a 10-year warranty.

Download PDF

report

Aerus HF 300 Operating instructions

Aerus HF 300 Operating instructions

Other documents