Garmin GPSMAP 2006/2006C User manual

Brand: Garmin

Model: GPSMAP 2006/2006C

Category: Equipment cleansing kit

Type: User manual

GPSMAP

2006/2010

& GPS 17

installation instructions

INSTALLATION INSTRUCTIONS

GPSMAP 2006C/2010C & GPS 17

storage medium, for any purpose without the express prior written consent of Garmin. Garmin hereby grants permission to download a single copy of this manual onto

a hard drive or other electronic storage medium to be viewed and to print one copy of this manual or of any revision hereto, provided that such electronic or printed

copy of this manual must contain the complete text of this copyright notice and provided further that any unauthorized commercial distribution of this manual or any

revision hereto is strictly prohibited.

Information in this document is subject to change without notice. Garmin reserves the right to change or improve its products and to make changes in the content

without obligation to notify any person or organization of such changes or improvements. Visit the Garmin Web site (www.garmin.co

m) for current updates and

supplemental information concerning the use and operation of this and other Garmin products.

Garmin

is a registered trademark of Garmin Ltd. or its subsidiaries and may not be used without the express permission of Garmin.

Safety Information

WARNING: This product, its packaging, and its components contain chemicals known to the State of California to cause cancer, birth defects, or reproductive harm.

This Notice is being provided in accordance with California’s Proposition 65. If you have any questions or would like additional information, please refer to our Web

site at http://www.garmin.com/prop65.

Limited Warranty

This Garmin product is warranted to be free from defects in materials or workmanship for one year from the date of purchase. Within this period, Garmin will at its

sole option repair or replace any components that fail in normal use. Such repairs or replacement will be made at no charge to the customer for parts or labor,

provided that the customer shall be responsible for any transportation cost. This warranty does not cover failures due to installation errors, abuse, misuse, accident, or

unauthorized alteration or repairs.

THE WARRANTIES AND REMEDIES CONTAINED HEREIN ARE EXCLUSIVE AND IN LIEU OF ALL OTHER WARRANTIES EXPRESS OR IMPLIED OR

STATUTORY, INCLUDING ANY LIABILITY ARISING UNDER ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE,

STATUTORY OR OTHERWISE. THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, WHICH MAY VARY FROM STATE TO STATE.

IN NO EVENT SHALL GARMIN BE LIABLE FOR ANY INCIDENTAL, SPECIAL, INDIRECT OR CONSEQUENTIAL DAMAGES, WHETHER RESULTING

FROM THE USE, MISUSE, OR INABILITY TO USE THIS PRODUCT OR FROM DEFECTS IN THE PRODUCT. Some states do not allow the exclusion of

incidental or consequential damages, so the above limitations may not apply to you.

Garmin retains the exclusive right to repair or replace the product or offer a full refund of the purchase price at its sole discretion. SUCH REMEDY SHALL BE

YOUR SOLE AND EXCLUSIVE REMEDY FOR ANY BREACH OF WARRANTY.

Online Auction Purchases: Products sold through online auctions are not eligible for rebates or other special offers from Garmin. Online auction conﬁrmations are

not accepted for warranty veriﬁcation. To obtain warranty service, an original or copy of the sales receipt from the original retailer is required. Garmin will not replace

missing components from any package purchased through an online auction.

International Purchases: A separate warranty is provided by international distributors for units purchased outside the United States. This warranty is provided by

the local in-country distributor and this distributor provides local service for your unit. Distributor warranties are only valid in the area of intended distribution. Units

purchased in the United States or Canada must be returned to the Garmin service center in the United Kingdom, the United States, Canada, or Taiwan for service.

To obtain warranty service, contact your local Garmin authorized dealer or call Garmin Product Support for shipping instructions and an RMA tracking number. The

product should be securely packed with the tracking number clearly written on the outside of the package. The product should then be sent, freight charges prepaid, to

any Garmin warranty service station. A copy of the original sales receipt is required as the proof of purchase for warranty repairs.

July 2005 Part Number 190-00228-01 Rev.F Printed in Taiwan

Garmin International, Inc.

1200 East 151

Street,

Olathe, Kansas 66062, U.S.A.

Tel. 913/397.8200 or 800/800.1020

Fax 913/397.8282

Garmin (Europe) Ltd.

Unit 5, The Quadrangle,

Abbey Park Industrial Estate,

Romsey, SO51 9DL, U.K.

Tel. 44/0870.8501241

Fax 44/0870.8501251

Garmin Corporation

No. 68, Jangshu 2

Road,

Shijr, Taipei County, Taiwan

Tel. 886/2.2642.9199

Fax 886/2.2642.9099

INSTALLATION INSTRUCTIONS

GPSMAP 2006C/2010C & GPS 17

INTRODUCTION

The GPSMAP 2006C/2010C Multi-Function Display (MFD) and GPS 17 must be properly installed according to the following instructions for

the best possible performance. To complete the installation, you need the appropriate fasteners, tools, and mounts listed in each section. These

items are available at most marine dealers. Always wear safety goggles, ear protection, and a dust mask when drilling, cutting, or sanding.

When drilling or cutting, always check ﬁrst to see what is on the opposite side of the surface. Mount the GPSMAP 2006C/2010C in a location

that provides a clear, glare-free view of the display and easy operation of the controls. If you experience difﬁculty installing the unit, contact

Garmin Product Support or seek the assistance of a professional installer.

GPSMAP 2010C Shown

Mounting Knob

Mounting Holes

Bail Mount

INSTALLATION INSTRUCTIONS

GPSMAP 2006C/2010C & GPS 17

INSTALLATION INSTRUCTIONS

Surface Mount

Tools

• Drill and Drill Bit

• Screwdriver

• Pencil

• Mounting Hardware (not included)

NOTE: Mounting hardware (fasteners) not included. Mounting holes are 5/16"

(7.9 mm) in diameter.

To install the Bail Mount and unit:

1. Using the bail mount as a template, mark the location of the four mounting holes.

Be sure to leave at least two inches of clearance behind the unit for the wiring.

2. Using an appropriate size drill bit, drill pilot holes for the fasteners.

3. Secure the bail mount to the surface with the fasteners.

4. Loosen the mounting knobs.

5. Slide the unit into the bail mount and tighten the mounting knobs.

Bail Mount

Bail mount

Mounting knobs

INSTALLATION INSTRUCTIONS

GPSMAP 2006C/2010C & GPS 17

Flush Mount

Tools

• Flush Mount Template

• Jig saw

• Masking tape

• Scissors

• Drill

• Drill bits—1/8" (3 mm) and 3/8" (6 mm)

• 1/16" (2 mm) Allen (Hex) wrench

• Sockets or wrenches

• Hammer

• Center punch

To ﬂush mount the GPSMAP 2006C/2010C:

1. Trim the Flush Mount Template and tape it in the location you want.

2. Using the center punch, indent the center of each mounting hole location.

3. Using an 1/8” (3 mm) drill bit, drill the four mounting holes.

4. Using a 3/8” (6 mm) drill bit, drill a hole for a location to begin cutting the mounting surface.

5. Using the Jig Saw, cut the mounting surface along the inside of the dashed line indicated on the template. Use a ﬁle and sandpaper to

reﬁne the size of the hole. Be very careful when cutting this hole. There is only a small amount of clearance between the case

molding and the mounting holes.

6. Install the four mounting studs into unit by screwing the shorter, threaded section into the back of the unit. Use a 1/16” (2 mm) Allen

wrench to tighten the mounting studs until the stop contacts the case. Be careful not to overtighten as this may damage the

mounting stud! The studs have a reusable thread-locking patch

pre-applied from the factory.

7. Place the unit in position in the cut-out of the mounting surface.

8. Place washers over the mounting studs, then thread on one

hex nut per mounting stud. Tighten all four until the unit is snug

against the mounting surface. Install and tighten the second hex

nut set on all four mounting studs to lock the ﬁrst set in place.

230mm

208mm

GPSMAP 2010/2010C/3010C

CUT MOUNTING SURFACE

ALONG INSIDE OF THIS LINE

UNIT OUTLINE

DRILL A 3/8" HOLE.

BEGIN CUTTING HERE

TRIM TEMPLATE ALONG THIS LINE TO AID FITTING

Be very careful when cutting this hole,

there is only a small amount of clearance�

between the unit and the Mounting Hole.

Flush Mounting the GPS

1. Trim the Flush Mount Template and tape in the desired location.

2. Using the Center Punch, indent the center of each Mounting Hole location.

3. Using an 1/8” (3mm) drill bit, drill the four Mounting Holes. (Drilling the mounting

holes before cutting the hole for the unit will allow for an easier installation.)

4. Using a 3/8” (6mm) drill bit, drill a hole for a location to begin cutting the mounting

surface.

5. Using the Jig Saw, cut the mounting surface along the inside of the dashed line

indicated on the template. Be very careful when cutting this hole, there is only a small

amount of clearance between the case molding and the Mounting Holes.

6. Install the four Mounting Studs into unit by screwing the shorter, threaded section

into the back of the unit. Use a 1/16” (2mm) Allen Wrench to tighten the Mounting Studs

until the stop contacts the case. Be careful not to overtighten as this may damage the

Mounting Stud! The studs have a reusable thread-locking patch pre-applied from the factory.

7. Place the unit in position in the cut out of the mounting surface.

8. Place washers over the Mounting Studs, then thread on one Hex Nut per Mounting Stud.

Tighten all four until the unit is snug against the mounting surface.

Install and tighten the second Hex Nut on all four Mounting Studs to lock the first one

in place.

Flush Mount Template

Flush Mount

Stud

Mounting surface

Washer Hex nuts

INSTALLATION INSTRUCTIONS

GPSMAP 2006C/2010C & GPS 17

Radar

ABOVE - BEST

BELOW - OK

EMI

SS JA

GOOD

BETTER

BEST

VHF Radio Antenna

Radar

EMI (Electromagnetic Interference)

from engine components

Signal Interference

NOTE: Mount the antenna at least 3 ft away from

(preferably above) the path of any radar beam or a

VHF radio antenna.

Bottom of GPS 17

Mounting holes

Installing the GPS 17

The GPS 17 can be ﬂush mounted or installed on any standard 1" O.D. (Outer

Dimension), 14 threads-per-inch marine mount. When mounting the GPS 17, the

cable can be run externally or through the mounting panel or through the center of

the marine mount.

The GPS 17 connects to the 18-pin Power/Data Cable on the GPSMAP

2006C/2010C and provides the GPS/WAAS signal for the unit. If two or more

GPSMAP 2006C/2010C units are installed, only one GPS 17 needs to be installed.

To ensure the best reception, mount the GPS 17 in a location that has a clear,

unobstructed view of the sky in all directions. Avoid mounting the GPS 17 where

it is shaded by the boat’s superstructure, a radome antenna, or mast. Sailboat

users should avoid mounting the unit high on the mast to prevent inaccurate

speed readings caused by excessive heeling. The unit provides more stable

readings if it is located nearer to water level. Mount the GPS 17 at least 3 ft

away from (preferably above) the path of any radar beam or a VHF radio

antenna. Temporarily secure the unit in the desired mounting location and test for

correct operation. With correct operation veriﬁed, permanently mount the unit. If

interference with other electronics is experienced, try a different location.

NOTE: Never paint the GPS 17 or clean it with harsh solvents.

To ﬂush mount the GPS 17:

1. Cut out the Mounting Template provided on page 11, and tape it on the selected mounting location.

2. Mark the center of each mounting hole by tapping the end of a center punch or pointed object with a hammer. If the cable is going to be

installed through the mounting panel, mark the center of the additional hole.

3. Drill the holes using the appropriate drill bit(s).

4. Align the GPS 17 over the mounting holes and fasten using M4 screws. The mounting threads in the GPS 17 are 8.10 mm deep. Do not

use screws that thread into the GPS 17 deeper than 8 mm, or the case may be damaged.

The GPS 17 can be installed with the coax through the panel

or on the outside of the unit. If the coax is run through the

panel, seal the outside exit area with marine sealant.

INSTALLATION INSTRUCTIONS

GPSMAP 2006C/2010C & GPS 17

To attach the enclosed pole mount to the GPS 17:

1. Thread the cable though the pole mount.

2. Align the tab on the mount to the notch on the GPS 17.

3. Use the enclosed screws to secure the mount to the base.

Attaching the Pole Mount to the GPS 17

Align notch

To mount the GPS 17 with cable outside mount:

1. Place the cable in the vertical slot along the side of the base of

the unit.

2. Screw the GPS 17 onto the mount. DO NOT overtighten the

head. It is possible to over tighten the unit and cut the cable.

3. With the GPS 17 and mount installed, ﬁll the remaining gap in

the cable exit with a marine sealant.

4. Route the cable away from sources of electronic interference.

To mount the GPS 17 with cable through mount:

1. Position the mount in the desired location and mark the

approximate center of the mount.

2. Drill a hole large enough for the cable to pass through.

3. Slide the cable through the mount and screw the GPS 17 onto

the mount.

4. Fasten the mount to the boat.

5. Route the cable away from sources of electronic interference.

Cable run internally

Cable run externally

Attaching the GPS 17 to a Pole Mount

INSTALLATION INSTRUCTIONS

GPSMAP 2006C/2010C & GPS 17

Wiring

There are two wiring diagrams provided for you convenience. The ﬁrst is a simple hook-up showing the GPSMAP 2006/2010 (using the 18-

pin wiring harness), the GPS 17 and the alarm circuit. The Alarm does not have to be wired for the unit to function. The second is a complete

wiring diagram showing the GPSMAP 2006/2010 (using the 18-pin wiring harness) interfacing with a variety of different equipment. The extra

5-pin wiring harness that came with the unit is intended for future interfacing features and does not require connection. Refer to the wiring

diagram that will best suite your needs. Make sure that all connections are good. For extra lengths of wire, 24 AWG (unless otherwise noted on

wiring diagram), shielded, twisted-pair wiring is recommended. We advise soldering all connections and sealing the connection with heat shrink

tubing. If you experience difﬁculty wiring the unit, please contact an installation professional in your area.

WIRE

COLOR

WIRE

COLOR

18 AWG

1 A

5 A

ALARM

SEE NOTE

GARMIN GPS 17

GPS SENSOR

BLACK

GROUND

YELLOW

RED

POWER

BLUE

WHITE

YELLOW

ALARM

GROUND BLACK

PORT 4 OUT GREEN

ACCESSORY ON ORANGE

DC INPUT RED

PORT 4 IN WHITE

COM 1 IN

COM 1 OUT

SHIP'S BATTERY

10-32 VOLTS

GARMIN

GPSMAP 2006/2010

NOTE:

THE ALARM OUTPUT CAN BE USED TO DRIVE A LAMP, HORN, OR BOTH.

MAXIMUM CURRENT IS 100 MILLIAMPS. A SWITCH OR RELAY CAN BE USED

TO SELECT BETWEEN VISUAL AND AUDIBLE ALERTS, IF REQUIRED

Diagram 1 - Basic Hook-up

INSTALLATION INSTRUCTIONS

GPSMAP 2006C/2010C & GPS 17

SHIP'S BATTERY

10-32 VOLTS

GARMIN GSD 20

SOUNDER MODULE

(SEE GSD 20

INSTALL INSTRUCTIONS)

4. A GARMIN SOUNDER UNIT (OTHER THAN GSD 20) CAN PROVIDE WATER DEPTH, WATER TEMPATURE,

AND SPEED VIA NMEA DATA FOR DISPLAY ON THE GPSMAP 2006/2010.

(-)

Diagram 2 - Complete Interface

INSTALLATION INSTRUCTIONS

GPSMAP 2006C/2010C & GPS 17

Final Wiring Connection

Once all the wiring is complete, plug the 18-pin harness into the center connector on the backside of the GPSMAP 2006/2010. The 5-pin port

on the right side is intended for future interfacing features and does not require connection at this time.

With power applied to the circuit, you may test the installation by pressing the

POWER key on the front of the unit. See the Owner’s

Manual for steps on initializing the receiver.

18-Pin Connector

5-Pin Connector

(for future use)

INSTALLATION INSTRUCTIONS

GPSMAP 2006C/2010C & GPS 17

Dill this 3/4” or 19 mm

hole if the coax is

going to be installed

through the mounting

panel

Drill using a

11/64” or 4.5 mm

drill bit

FLUSH MOUNT DRILLING TEMPLATE

Garmin International, Inc.

1200 East 151

Street, Olathe, Kansas 66062, U.S.A.

Garmin (Europe) Ltd.

Unit 5, The Quadrangle, Abbey Park Industrial Estate, Romsey, SO51 9DL, U.K.

Garmin Corporation

No. 68, Jangshu 2

Road, Shijr, Taipei County, Taiwan

www.garmin.com

Part Number 190-00228-01 Rev. F

Garmin GPSMAP 2006/2006C User manual

Brand: Garmin

Model: GPSMAP 2006/2006C

Category: Equipment cleansing kit

Type: User manual

Download PDF

report

Garmin GPSMAP 2006/2006C User manual

Garmin GPSMAP 2006/2006C User manual

Related papers

Other documents