CAUTION: To avoid possible electrical shock, be sure that power supply is
turned off before installing or servicing this fixture.
STEP 1:
STEM/CANOPY MOUNT (Figure 1)
• Secure canopy assembly to the outlet box with screws (included
in the Pendant Kit).
• Attach stem to the canopy and to housing.
• Make wiring connections.
SURFACE MOUNT
• The cylindrical housing is attached to the outlet box (on ceiling)
by using (2) mounting screws shown in Figure 2.
• Make wiring connections.
STEP 2: To Install Upper Reflector: Cut plastic tie wrap securing heat sink to
bracket. Install quartz mini-can frosted lamp. Make sure the lamp
wattage matches the markings on the heat sink.
WARNING: DO NOT handle quartz lamps with bare hands.
Grease from fingerprints may cause premature end of life or
shattering of lamp.
Install heat sink to upper reflector assembly carefully guiding lamp
into reflector opening (Figure 3). Rotate heat sink until flanges are
seated under retention springs(Figure 4). Insert this completed
assembly into the cylindrical housing until seated securely.
PORTFOLIO
Installation Instructions for H17500QT4 and H17250QT4 Commercial Surface
Cylinders and for H77500QT4 and H77250QT4 Wall Mount Cylinders
Customer First Center 1121 Highway 74 South Peachtree City, GA 30269 12/18/06 704244
Heat Sink
Upper Reflector
Assembly
Lamp
Reflector
Opening
Mounting Screws
Lower Reflector
Assembly
Upper Reflector
Assembly
Heat Sink and
Lamp Assembly
Housing
Pendant Kit, H836
(Sold Separately)
Figure 3
Figure 1 Figure 2
PORTFOLIO
TO INSTALL LOWER REFLECTOR ASSEMBLY
STEP 3: Attach safety tether from lower reflector assembly to mounting bracket inside the can via clip.
Reflector Assembly is held in place with torsion springs that pass through slots inside the can. (Figure 5)
WALL MOUNT ONLY
STEP 4: Install wall housing/wall bracket shown in Figure 6 over the outlet box on the wall.
STEP 5: Using the (2) screws shown in Figure 5, secure the assembly to the outlet box.
STEP 6: Make wiring connections.
STEP 7: Follow steps 2-3 for trim installation.
RELAMPING: Allow sufficient time for the lamp to cool. Relamping can be performed from below the
fixture.
To relamp from below the fixture: Remove lower trim and then remove
upper reflector by pressing the four retention springs inward (Figure 7).
Rotate heat sink to clear retention springs and carefully separate from
reflector assembly. Replace lamp and reassemble as described in steps
1-4.
CLEANING: First, gently wipe with a soft, clean, dry lint-free cloth to
remove loose dust. Then, use mild detergent solution on a soft cloth to
remove finger prints and stains. Rinse with clean, soft water and dry with
lint-free cloth.
Customer First Center 1121 Highway 74 South Peachtree City, GA 30269 12/18/06 704244
Depress these 4 retention springs
to install/remove the upper trim.
Screws
Wall Bracket
Screws
WALL MOUNT ONLY
Figure 4
Figure 7
Figure 6
Clip
Safety
Tether
Torsion
Springs
Slots that Torsion
Spring Hooks into
Hole that
safety tether
clips
For Clarity, Housing
Can is not shown
Figure 5
-
1
-
2
Cooper Lighting H17250QT4 User manual
- Category
- Kitchen & houseware accessories
- Type
- User manual
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Cooper Lighting MD639T6G65 User manual
-
-
-
-
-
-
-
-
-
Other documents
-
Generation Lighting 1153AT Installation guide
-
Halo EL406930 Installation guide
-
-
Eaton Portfolio DRT8B Installation Instructions Manual
-
-
-
Halo ML5606930 Installation guide
-
-
-
