Panasonic PT-L735NTU User manual

Part for Network Functions and

SD Memory Card Functions

(PT-L735NTE)

2

Notes for use ..........................4

Information on SD Memory Card ......4

Instructions on handling ....................4

Instruction on storage ........................4

For protection of important data ........4

To create a backup copy of the data

stored on the SD card........................5

Write protection switch ......................5

Information on wireless card ............6

Available channels ............................8

Typical applications of network

functions / SD Memory Card

......9

Examples of use of network functions

....9

SD Memory Card ................................9

Examples of use of network

functions / SD Memory Card............10

Insertion and removal of wireless

card and SD Memory Card into /

from the projector

....................11

Wireless card............................................11

SD Memory Card ......................................12

Insertion and removal of wireless card

into/from personal compute

r ..........13

Installation of software ........14

Wireless Manager 3.0/

Image Creator 1.0A ..........................14

Wireless LAN Driver..........................15

Wireless Simple Connection (live mode)

....

21

Operations on the projector ..................

21

Operations on the personal computer

......22

Releasing the connection to the projector

..23

Temporary releasing........................23

Complete releasing..........................23

Network setting ....................25

Use of inter-PC communications ....25

If the communication mode of 802.11

ad hoc (peer-to-peer) is selected:....25

Use of access point (AP)..................26

Setting example ..............................26

Setting up the projector....................27

Settings on the personal computer

......30

Settings of TCP/IP ..........................30

Settings for use of optional wireless

card (ET-CDWL2E)..........................34

Use of Wireless Manager 3.0

....38

Start-up ..............................................38

Live mode ..........................................38

Selecting the transfer mode ............38

In live mode ....................................39

Quitting and resuming live mode ....39

Meeting mode (screen capture) ......39

Selection of capture format..............40

Operations after image acquisition ..40

Setting of capture delay time ..........40

"PowerPoint Presentation"mode

....41

Presentation mode............................41

Setting of capture delay time ..........41

Presentation mode ..........................42

Progress bar ....................................42

Switching display mode ..................42

Other functions ................................44

Searching projector..........................44

Registering projector........................44

Deleting projector ............................44

Confirming connection ....................44

Displaying the sender, sender's name

..45

Setting a shortcut key ......................45

Setting automatic play ....................45

Setting Simple Connection ..............45

Contents

3

Use of Web browser control ....46

Settings on the projector..................46

Web control......................................46

Web power supply ..........................46

Web password ................................46

Settings on the personal computer 47

Operation of Web browser control..48

Top screen ......................................48

Projector control ..............................49

Basic control screen ........................49

Option control screen ......................49

Monitor information screen ..............50

SD control........................................51

SD file list screen ............................51

SD thumbnail screen ......................51

Presentation screen ........................52

Changing password ........................52

Using a PDA ......................................53

Starting the Web browser control

(PDA) ..............................................53

Top screen ......................................53

Menu screen....................................54

Projector Control..............................54

SD Control ......................................55

Status ..............................................55

Use of Image Creator 1.0A....56

Starting/ending Image Creator 1.0A

......56

Start-up............................................56

End ..................................................56

Functions on the main screen ........56

Converting and saving captured

images................................................58

Capturing presentation files created with

Microsoft PowerPoint97/2000/2002

......60

Capturing JPEG, BMP, TIFF or PNG files

created with other applications

............61

Press the "Capture image" button ..61

Images not to be captured ..............61

Capturing files by drag-and-drop

operation..........................................61

Sorting images ................................62

Deleting images ..............................62

Make conversion settings when

writing an image ..............................63

DCF standard ....................................65

Directory (folder) name....................65

File name ........................................65

File format........................................65

How to use SD card ..............66

Playing images of SD Memory Card

......66

SD Viewer (SD guide display) ..........67

Folder selection screen....................67

File selection screen........................67

Settings of automatic play (auto play)

..68

Uninstallation of software ....70

Wireless Manger 3.0..........................70

Image Creator 1.0A ..........................70

Wireless LAN Driver..........................70

Explanation of terms ............71

Before placing a repair order

....74

Trademark Information

................

76

Contents

4

Notes for use

Information on SD Memory Card

This SD card is a semiconductor memory with the size of 24mm x 32mm x 2.1mm, as

small as a postage stamp, and is expected to be a next-generation recording medium

that replaces minidisks (MDs), compact disks (CDs) and cassette tapes. The card

allows repetition of data reading, writing and deleting.

Instructions on handling

Abstain from the following:

• To disassemble or modify the card

• To give the card a strong impact, twisting, bending, dropping, treading, or water

wetting

• To rub the card with a sheet of cloth or plastics or to bring the card near to

anything that is likely to generate static electricity or electromagnetic field.

• To touch the metallic terminal of card with hand or metallic object, to affix

stickers, or to stain the card.

• To peel off the label that is affixed to the card.

• To affix other labels or stickers.

• To insert the card into a device that does not accept an SD card (e.g., device for

multimedia cards).

• To insert other matters than SD Memory Card in the SD Memory Card slot of

the projector.

• To use cracked or deformed card.

• To use the card in a moist place such as bathroom or in a dusty place such as

warehouse.

Instruction on storage

Be sure to put the card in the case when it is taken out from the main body.

• Do not put the card in a vehicle or in a place exposed to direct sunlight where it

may become hot.

• Do not keep the card in a vehicle that may become hot, a place exposed to

direct sunlight or other places in which the temperature is likely to increase, or a

place in which corrosive gases may arise.

For protection of important data

• Do not turn off the power or remove the SD Memory Card when data is being

read or written (or when the SD Memory Card access lamp is blinking). Doing

this may destroy the data.

• Do not forget to make backup of the data stored in the SD card. Note that user's

important data is subject to potential destruction although it is very rare to occur.

To create a backup copy of the data stored on the SD card

Double click and open the icon of SD card

drive in My Computer of your personal

computer (on the desktop if your computer is

Macintosh) and drag and drop the "DCIM"

folder onto desktop (while pressing the

"Option" button, for Macintosh machine). This

operation can create copies of all data within

the "DCIM" folder into your personal

computer.

Write protection switch

• Putting the write-protection switch of SD

card to the "LOCK" position will disable

image-editing operation such as deleting or

moving on the projector (attempt of

operation will bring error message).

• If the SD card is inserted into the personal

computer by means of the PC card adaptor

while the write-protection switch of SD card

is set to the "LOCK" position, a blue-screen

warning indication will appear when access

is made. If this occurs, press any button on

the keyboard of your PC to return the

indication to the original one. Before using

an SD card in your personal computer,

ensure that the write-protection switch is

not set to the "LOCK" position.

5

LOCK

Write-protect switch

Notes for use

Please be advised of the following information in advance:

• The manufacturer shall not be responsible for any damage, whether direct or

indirect, caused by the use of or by the fault of the product.

• The manufacturer shall not be responsible for any damage or destruction of data

caused by the product.

6

Information on wireless card

Notes for use

The optional wireless card (ET-CDWL2E) uses radio wave in the 2.4 GHz band.

Although it is not necessary to have a license for radio station to use the wireless

card, fully understand the following instructions:

Do not use the cards near other sources of radio

emissions.

The following devices may use the same frequencies that are used by the

wireless card. If the wireless card is used near such devices, radio interference

may prevent successful communication, or it may result in slower communication

speeds being achieved.

• Industrial, scientific, medical equipment, etc

• Electric stoves, etc

• Built-in radio devices used for identifying moving equipment in industrial

production lines

• Certain low-power radio devices

Keep the wireless card as far away as possible from

devices such as mobile telephones, TVs and radios

when using such devices

Devices such as mobile telephones, TVs and radios use different frequencies

from the wireless card, so that there will be no effect on either wireless card

communication or on reception or transmission for such devices. However, radio

emissions from the wireless card may cause video or audio interference.

77

Notes for use

Radio emissions from the wireless card will not travel

through steel framework, metal sheets or concrete.

It is not possible to keep communication through walls or floors made of

reinforcing steel bars, metals or concrete although it is possible to keep

communication through walls and floors made of wood or glass (excluding glass

reinforced with metal wires).

8

N5HBD0000024

Notes for use

Available channels

The channels (frequency bandwidth) that are available for the wireless card to

use will vary depending on the country or area where the wireless card is being

used. Refer to the following table as a guide.

Country / Area

Japan

USA

ARIB

STD33 &

T66

FCC part 15

22

23

1~14

1~11

2 412 MHz~

2 484 MHz

2 412 MHz~

2 462 MHz

Canada IC

Taiwan

Malaysia

UK, Germany, France,

Italy, Belgium, Austria,

Sweden, Norway,

Denmark, Switzerland,

Holland, Finland,

Portugal, Greece,

Thailand, Korea,

Australia, New Zealand

Spain

Singapore

DGT

SIRIM

ETSI

300.328

ETSI

300.328

IDA

24

25

26

1~13

10,11

10~13

2 412 MHz~

2 472 MHz

2 457 MHz~

2 462 MHz

2 457 MHz~

2 472 MHz

Certification

Last two digits

of card

number *

Operating

channels

Frequency band

(median frequency)

* To check the region of intended use for the wireless card which

you have purchased, check the last two digits of the product

number which appears on the label on the reverse side of the card

in the position shown in the illustration at right.

Note:

The wireless card cannot be used in countries other than the

country of purchase. If you try to use it in other countries, you

may be infringing the radio transmission laws and regulations of

that country.

9

Wireless Manager3.0

Wireless LAN Driver

Typical applications of network functions / SD Memory Card

For Wireless Easy

Connection,

see page 21

For Network settings,

see page 25

For Installation of

software,

see page14

Projecting images from the personal

computer by wireless

Projecting images from SD card using Web

browser control

See page 66

Examples of use of network functions

SD Memory Card

Controlling the projector using Web

browser control

For Wireless Easy

Connection,

see page 21

For Network settings,

see page 25

For Web browser

control,

see page 46

Using the Web browser, it is possible to access the

projector and control power ON, OFF and other

functions of the projector.

Images from personal computer can be projected by

wireless all the time

This card allows the user to view list of images

(thumbnail images) recorded on the SD Memory Card to

perform automatic play such as slide show.

Installation

Transmission

Optional

wireless card

(ET-CDWL2E)

Loaded with

the included

wireless card

Loaded with

the included

wireless card

Optional

wireless card

(ET-CDWL2E)

Operation with web

browser control

SD Memory Card

10

The supplied Wireless Manager 3.0 allows the user to

transfer image data from the personal computer to the

SD card inserted in the projector and to record the data

on the card. Thus the user can project images

changing very quickly to desired ones.

The Web browser allows the user to access the

projector and to project the image data stored on the

SD Memory card inserted in the projector.

Transferring image data from personal

computer to the projector and recording

them onto the SD Memory card inserted in

the projector

Projecting images from SD card using Web

browser control

For Wireless Easy

Connection,

see page 21

For Network settings,

see page 25

For Installation of

software,

see page 14

For Wireless Easy

Connection,

see page 21

For Network settings,

see page 25

For Web browser

control,

see page 46

Wireless Manager3.0

Wireless LAN Driver

Examples of use of network functions / SD Memory Card

Typical applications of network functions / SD Memory Card

Installation

Transmission

Optional

wireless card

(ET-CDWL2E)

Loaded with

the included

wireless card

Operation with web

browser control

SD Memory

Card

Loaded with

the included

wireless card

SD

Memory

Card

Optional

wireless card

(ET-CDWL2E)

Record

11

Wireless card

1

2

3

Insertion

• Turn off the power by putting the [MAIN POWER] switch to the " " position.

• Forced insertion of the card in wrong direction may cause failure.

1

3

2

Removal

Turn off the power by putting the [MAIN POWER] switch to the " " position.

Insertion and removal of wireless card and

SD Memory Card into / from the projector

Insert the card until

it is locked.

Attach the card

lock.

Secure the card

lock with the

supplied screw.

3

2

1

Remove the screw

of card lock.

Remove the card

lock.

Press the eject

switch to take out

the card.

3

2

1

(supplied)

Card lock

(supplied)

Hexagon wrench

(Eject switch)

12

Insertion

Forcible insertion of the SD card in a wrong direction may cause a fault.

Removal

Be sure to confirm the access lamp is not blinking before card removal.

Removing the card while the lamp is blinking may destroy the data on the card.

Press the centre to

release the lock and take

out the card.

Insert a card until it is

locked

SD Memory Card

Insertion and removal of wireless card and SD Memory Card into / from the projector

Access lamp

13

Removal

Quit Wireless Manager 3.0 if it is in use.

Left-click the [PC card] icon appearing on the task bar at the

right bottom of screen.

If the [PC card] icon is not appearing:

Go to [Start Menu]→[Control Panel] and open [PC card].

Checkmark [Show control on the task bar] and press [OK].

Select [Panasonic Wireless LAN PC Card] and click [Stop].

Press [OK] and take out the wireless card.

3

2

1

Insertion

• Before inserting the wireless card, be sure to install the included Wireless

LAN Driver software (see page 15).

• This illustration is for the case of optional wireless card (ET-CDWL2E).

For other cards, see the instruction manual for the relevant card.

• Also read well the instruction manual for your personal computer.

• Forced insertion of the card in wrong direction may cause failure.

1

2

Insertion and removal of wireless card into/from personal computer

Fit the card to the

adaptor.

Insert the card and the

adaptor into the PC card

slot of the personal

computer.

2

1

14

Installation of software

note:

• Quit all software in action on Windows. Otherwise your installation may be

unsuccessful.

• Uninstall Wireless Manager 2.0 or Image Creator 1.0 if it has been installed

before this installation. (See page 70)

• If your PC runs on Windows XP/2000, the authority of Administrator is required

for this installation.

Wireless Manager 3.0:

This software can be used to transmit screen images and image files (JPEG and

PNG images) from the personal computer to the projector through wireless LAN.

Image Creator 1.0A:

This software can be used to convert PowerPoint files into image data.

Wireless Manager 3.0 / Image Creator 1.0A

Set the supplied CD-ROM in the CD-ROM drive.

This automatically activates the installation program, displaying a window as

shown below.

Note:

If the program is not automatically launched, double-click [Easy Install]

→

[Easy_

Inst.exe] in the CD-ROM.

1

Click [Wireless Manager 3.0].

Follow the instructions on the screen to carry out installation.

2

Click [Image Creator 1.0A].

Follow the instructions on the screen to carry out installation.

3

15

Installation of software

Notes :

• Installation of the Wireless LAN Driver in your personal computer must have

been completed before inserting the wireless card into the computer.

• If the card is accidentally inserted in the personal computer before installation of

the driver, the automatic hardware detection will find the card as an unidentified

device. If this is the case, do not remove the card, but carry out the following

steps with the card kept inserted before installation.

For Windows XP/2000: Go to [Control Panel]

→

[System]

→

[Hardware]

→

[Device Manager], and if any unidentified device or

Panasonic Wireless LAN PC Card is found in the list,

uninstall the item.

For Windows 98 SE/Me: Go to [Control Panel]

→

[System]

→

[Device Manager],

and if any unidentified device or Panasonic Wireless

LAN PC Card is found in the list, uninstall the item.

Wireless LAN Driver

A Wireless LAN Driver must be installed to use the wireless card on the personal

computer.

• The following section describes installation of the optional wireless card (ET-

CDWL2E). For other cards, see the instruction manual for the relevant card.

16

For Windows XP:

Click [Wireless LAN Driver] on the

screen of Procedure 1 on page 14.

This will activate the installer for wireless LAN

1

Click [Next].

A License Agreement message appears.

2

Click [Yes].

3

Specify the destination for saving

the utility and click [Next].

A logo authentication message appears.

4

Click [Continue].

5

Click [Finish].

6

Installation of software

17

Insert an optional wireless card

through a CF card adaptor.

(See page 13)

This will activate Found New Hardware Wizard.

7

Confirm that [Automatically install

the software] is checkmarked and

click [Next].

A logo text message appears.

8

Click [Continue].

A wizard completion message appears.

9

Click [Finish].

A logo authentication message appears.

10

Installation of software

When installation is complete, confirm as follows:

Go to [Start]

→

[Programs]

→

[Connect To]

→

[Show all connections], and ensure

that a [Panasonic Wireless LAN PC Card] icon has been added to the wireless

network connections.

18

For Windows 2000:

Click [Wireless LAN Driver] on the

screen of Procedure 1 on page 14.

This will activate the installer for wireless LAN

1

Click [Next].

A License Agreement message appears.

2

Click [Yes].

3

Specify the destination for saving

the utility and click [Next].

The software is downloaded, and [Digital signature

was not found] appears.

4

Click [Yes].

Following the instructions on the screen, go along

the steps.

5

Click [Finish].

Installation is complete.

6

Insert an optional wireless card

through a CF card adaptor.

(See page

13)

Following the instructions on the screen, go along

the steps.

7

Installation of software

19

For Windows 98SE/Me:

Click [Wireless LAN Driver] on the

screen of Procedure 1 on page 14.

This will activate the installer for wireless LAN

1

Click [Next].

A License Agreement message appears.

2

Click [Yes].

3

Specify the destination for saving

the utility and click [Next].

The software is downloaded.

4

Confirm that [Yes, I want to restart

my computer now.] is checkmarked

and click [Finish].

The personal computer will be rebooted.

5

Insert an optional wireless card

through a CF card adaptor.

(See page 13)

If the icon cannot be found, select [Start]

→

[Program]

→

[Wireless Network]

→

[Wireless

Network LAN Adapter].

6

Installation of software

20

For Windows CE:

In the supplied CD-ROM, go to

[Wireless Card], open [Win CE] and

then click [setup.exe].

A screen for selection of folder setting language

appears.

1

Select [English], click [OK] and

click [Next].

A license window appears.

2

Click [Yes].

Following the instructions on the screen, go along

the steps.

3

Click [Finish].

As [Unable to connect….] appears on the PDA

screen, click [OK].

4

Insert the optional wireless card

(ET-CDWL2E) into PDA.

5

Installation of software

Note:

Before starting software installation, enable data communication between the

personal computer and Personal Digital Assistant (PDA) via Active Sync

Page is loading ...

Panasonic PT-L735NTU User manual

This manual is also suitable for

Panasonic PT-L735NTU User manual

Related papers

Other documents