Marshall electronic V-R653-IMD-TE User manual

Brand: Marshall electronic

Model: V-R653-IMD-TE

Type: User manual

This manual is also suitable for

Computer Monitor V-R653-IMD-TE

Marshall Electronics

V-R653-IMD-TE

High Definition Triple LCD Monitor with In-Monitor Display

Operating Instructions

Contents

Product Overview.......................................................................................................................................................................................................................................................3

Features.......................................................................................................................................................................................................................................................................3

Installation and Initial Setup .....................................................................................................................................................................................................................................4

Unpacking ..............................................................................................................................................................................................................................................................4

Installation..............................................................................................................................................................................................................................................................4

Connections and Power-On...................................................................................................................................................................................................................................4

Top and Front Panel Features ..................................................................................................................................................................................................................................5

Power Button..........................................................................................................................................................................................................................................................5

Menu Navigation Buttons.......................................................................................................................................................................................................................................5

User-Definable Function Buttons...........................................................................................................................................................................................................................5

RotoMenu™ Knob..................................................................................................................................................................................................................................................5

Image Adjustment Knobs.......................................................................................................................................................................................................................................5

LED Tally................................................................................................................................................................................................................................................................5

Rear Panel Features...................................................................................................................................................................................................................................................6

HD-SDI Input and Output.......................................................................................................................................................................................................................................6

Power Input............................................................................................................................................................................................................................................................6

Tally Interface (HD-15)...........................................................................................................................................................................................................................................6

RS-422/485 Serial Interface...................................................................................................................................................................................................................................6

Compatible Input Formats......................................................................................................................................................................................................................................... 7

On-Screen Menu.........................................................................................................................................................................................................................................................7

STRUCTURE OVERVIEW ....................................................................................................................................................................................................................................7

MAIN MENU AND NAVIGATION ..........................................................................................................................................................................................................................8

MARKER SETUP SUBMENU................................................................................................................................................................................................................................9

16:9 Markers....................................................................................................................................................................................................................................................9

4:3 Markers....................................................................................................................................................................................................................................................10

Marker Background .......................................................................................................................................................................................................................................10

Center Marker................................................................................................................................................................................................................................................10

VIDEO CONFIGURATION SUBMENU ...............................................................................................................................................................................................................11

Monochrome Mode........................................................................................................................................................................................................................................11

Blue-Only Mode.............................................................................................................................................................................................................................................11

Pixel-to-Pixel Mode........................................................................................................................................................................................................................................12

Aspect Ratio Settings ....................................................................................................................................................................................................................................12

Curtain Color..................................................................................................................................................................................................................................................13

COLOR CONFIGURATION SUBMENU..............................................................................................................................................................................................................14

Ctemp/Gamma...............................................................................................................................................................................................................................................14

Red, Green, Blue Offset ................................................................................................................................................................................................................................14

Gray Levels....................................................................................................................................................................................................................................................15

Saving and Loading User Presets.................................................................................................................................................................................................................16

Save Defaults.................................................................................................................................................................................................................................................16

Software Version Display...............................................................................................................................................................................................................................16

DEINTERLACER SUBMENU..............................................................................................................................................................................................................................17

Deinterlacer Mode .........................................................................................................................................................................................................................................17

Film Mode ......................................................................................................................................................................................................................................................18

Film Indicator .................................................................................................................................................................................................................................................18

Motion Display ...............................................................................................................................................................................................................................................18

OSD CONFIGURATION SUBMENU...................................................................................................................................................................................................................19

IMD State.......................................................................................................................................................................................................................................................19

Status Display................................................................................................................................................................................................................................................19

OSD Tally.......................................................................................................................................................................................................................................................20

LED Tally .......................................................................................................................................................................................................................................................21

Time Code .....................................................................................................................................................................................................................................................21

Audio Monitor.................................................................................................................................................................................................................................................21

IMD CONFIGURATION SUBMENU....................................................................................................................................................................................................................22

Overview........................................................................................................................................................................................................................................................22

IMD Protocol ..................................................................................................................................................................................................................................................22

IMD ID#..........................................................................................................................................................................................................................................................23

IMD Group # ..................................................................................................................................................................................................................................................23

IMD Name......................................................................................................................................................................................................................................................23

IMD Baud Rate ..............................................................................................................................................................................................................................................23

IMD Fixed Align..............................................................................................................................................................................................................................................23

IMD Fixed Color.............................................................................................................................................................................................................................................23

IMD Fixed String............................................................................................................................................................................................................................................23

Tally Source...................................................................................................................................................................................................................................................24

IMD Tally Mode..............................................................................................................................................................................................................................................24

SERVICE SUBMENU ..........................................................................................................................................................................................................................................25

Specifications...........................................................................................................................................................................................................................................................26

Maintenance.............................................................................................................................................................................................................................................................. 27

Warranty....................................................................................................................................................................................................................................................................27

Product Overview

The V-R653-IMD-TE is a dual 10.4” LCD monitor with HD-SDI inputs and In-Monitor Display functionality – a cost-

effective "all-in-one" solution for post-production houses, broadcasters, and mobile units. This fully integrated approach

eliminates the need for additional or separate Under Monitor Displays and allows UMD information and tallies to be

displayed directly within a Marshall flat panel monitor, while saving precious rack space. A variety of features are readily

available including on-screen Video Time Code, three-color "Soft" Tallies, Audio Presence Indicator, and a new

RotoMenu™ feature that allows fast, direct, and easy menu navigation.

The V-R653-IMD-TE integrates easily with existing Tally systems and controllers, including Image Video, TSL, and MEI

protocols. This 4RU unit also ships ready to rack mount and provides up to 20% more screen when compared to our

competitors' LCD and CRT models that occupy the same space. This is in addition to the benefits of low weight and power

consumption when compared to similar CRT products and separate Under Monitor Display configurations. The V-R653-

IMD-TE4U is a perfect solution for video wall applications and systems.

Each screen offers a single HDSDI/SDI input with active loop-through capability. Additional features include ultra-wide

viewing angles, color temperature adjustment, adjustment settings memory, frame markers, Pixel-to-Pixel mode, Blue

Only mode, and user-definable function buttons. The V-R653-IMD-TE can also be used as a set of standalone displays

with HDSDI loop-through.

Features

■

High-Resolution Triple 6.5” Panels

The V-R653IMD-TE features three all-digital TFT-MegaPixel™ active matrix LCD systems with 2.4 million pixels each.

The LCD panels feature a brightness of 650 cd/m

, 500:1 contrast ratio, and a 160° all-around viewi ng angle making

them ideal in a variety of environments and lighting conditions.

■

In-Monitor Display

In-Monitor Display allows on-screen text and tally indication, controlled locally or remotely via a variety of industry

standard protocols.

■

OSD Features

Embedded time code and an embedded audio presence indicator can be displayed on the screen in a variety of

configurations.

■

Advanced Features

Color temperature adjustment, aspect ratio settings, blue-only mode, and monochrome mode are a few of the

advanced features making the V-R653-IMD-TE at home in any broadcast environment. Pixel-to-Pixel mode also allows

native display of any incoming image format.

■

Flexible Screen Markers

A variety of screen markers in both 4:3 and 16:9 modes allow accurate monitoring of the different aspect ratios used in

broadcast environments.

■

User-Definable Function Buttons

Two user-definable function buttons allow quick access to numerous settings and features including aspect ratio,

screen markers, monochrome mode, color temperature, and more.

Installation and Initial Setup

■

Unpacking

Carefully unpack the V-R653-IMD-TE monitor and verify that the following items are included:

• V-R653-IMD-TE Monitor

• V-PS12-6.6A Power Supply with 2-Pin Twist Lock Connector

• Operating Instructions

Inspect the unit for any physical damage that may have occurred during shipping. Should there be any damage,

immediately contact Marshall Electronics at (800) 800-6608. If you are not located within the continental United States,

call +1 (310) 333-0606.

■

Installation

The V-R653-IMD-TE can be mounted in any standard EIA 19” equipment rack. The attached rack ears can be angled

to provide the user control over the viewing angle. Adequate ventilation is required when installed to prevent possible

damage to the monitor’s internal components.

■

Connections, Power-On and Initial Setup

Plug the V-PS12-6.6A power supply into an AC power source (100-240 V @ 50/60 Hz). Attach the 2-pin twist lock

connector to the back of the monitor. Please note that 12VDC can be also supplied directly to the monitor from a

variety of sources. The monitor will draw no more than 6.0 Amps at 12 Volts in operation.

Connect the required cables for video signal input and output. (Power must be applied to the V-R653IMD-TE for the

active loop-though outputs to be activated.) All BNC connectors are rated at 75Ω.

All screens default to ‘ON’ when power is supplied. Video will automatically be detected and displayed on the screen.

For IMD setup details, see IMD Configuration Submenu on page 22.

Rack ears on either side of monitor

Top and Front Panel Features

Power Button

Turn the monitor on by pressing the power button.

In the ON state, the LED above the power button will

illuminate green.

Menu Navigation Buttons

Use the Menu, ↑, ↓, and Select buttons to display

and navigate the on-screen menu (See Main Menu

and Navigation – Page 8).

User-Definable Function Buttons

Two user-definable function buttons can be used for

direct access to various settings. Functions are

assigned using the on-screen menu (See User-

Definable Function Buttons – Page 15).

RotoMenu™ Knob

The RotoMenu™ knob is alternate means of

accessing and navigating the main menu, using only

a single control.

Image Adjustment Knobs

Use the image adjustment knobs to adjust color

saturation, brightness and contrast of the image.

The status of each image adjustment parameter is

shown on the bottom left of the screen, with values

ranging from 0 to 100. Pressing each knob resets

the corresponding adjustment to its default setting

(50).

LED Tally

Two LED tally lights (red and green) are available

beside each screen. Each tally light can be

controlled from a variety of sources (See Tally

Source – Page 24).

Rear Panel Features

HD-SDI Input and Output

Each screen has one HD-SDI input and one active

loop-through output. Note: No more than 4 screens

should be connected in one loop.

Power Input

Connect the 12VDC input to the 2-Pin twist lock

power input connector. Power can be supplied from

the included power supply, or from a variety of DC

sources supplying at least 6.0 Amps at 12 Volts.

IMPORTANT: If using a power source other than the

included power supply, be sure that the polarity of

the DC input is correct:

Tally Interface (HD-15)

Both LED tally and OSD tally can be activated via

the HD-15 connector by connecting the

corresponding pin to ground. A variety of external

devices can be used to perform the contact closure.

No additional power should be supplied to the HD-

15 port. See pin-out details on page 26.

RS-422/485 Serial Interface

The RS-422/485 ports are used to remotely control

the IMD or all V-R653-IMD-TE features, using a

variety of industry standard protocols. (Note:

Connector/pin-out may need to be adapted

depending on protocol and controlling device

used. See pin-out details on page 26.) Only one

connection to either port is needed to control the

monitor. The second port can be used to loop

multiple monitors in the same bus.

IN OUT

Compatible Input Formats

The following SDI standards are supported by the V-R653-IMD-TE:

525i, 625i

1035i/60, 1035i/59.94

1080i/60, 1080i/59.94, 1080i/50

1080psF/24, 1080psF/23.98

720p/60, 720p/59.94, 720p/50

On-Screen Menu

STRUCTURE OVERVIEW

Marker 16:9

Off, 95%, 93%, 90%, 88%, 80%, 1.85:1, 2.35:1, 4:3, 14:9, 13:9

Marker 4:3

Off, 95%, 93%, 90%, 88%, 80%

Marker Backgrd

Off, 50% Gray, Black

Marker Setup

Center Marker

Off, On

Monochrome

Off, On

Blue Only

Off, On

Pixel to Pixel

Off, On

Aspect Ratio

4:3, Scaled 4:3, 16:9, 16:9 Centered

Video Config

Curtain Color

Blue, Red, Green, White, Black

CTemp/Gamma

55K, 65K, 93K, Linear

Red Offset

0-100

Green Offset

0-100

Blue Offset

0-100

Red Gain

0-100

Green Gain

0-100

Color Config

Blue Gain

0-100

Gray Levels

RGB = 000 - 255

Function 1

Marker, Center Marker, Marker Background, IMD, Time Code, OSD Tally, Audio Monitor, Aspect Ratio, Pixel to

Pixel, CTemp/Gamma, Blue Only, Monochrome

Function 2

Marker, Center Marker, Marker Background, IMD, Time Code, OSD Tally, Audio Monitor, Aspect Ratio, Pixel to

Pixel, CTemp/Gamma, Blue Only, Monochrome

Save Defaults

Back, Save, Mfg

Load Config

Mfg, User 1, User 2, User 3, User 4, User 5, User 6

Save Config

User 1, User 2, User 3, User 4, User 5, User 6

Main Board

(Main board firmware version number displayed)

Keypad

(Keypad firmware version number displayed)

System Config

CPLD

(CPLD firmware version number displayed)

Deint. Mode

Auto, Motion Adaptive, Field to Frame, Interpolate(Bob), Static Mesh(Weave)

Film Mode

Auto, 2:2 only, 3:2 only

Film Indicator

Off, On

Deinterlacer

Motion Display

Off, Noise, Motion

IMD State

Off, On

Status Display

Off, On

OSD Tally

Off, RGY, RG, GR, IMD

LED Tally

Off, On

Anc. Time Code

Off, LTC, VITC

OSD Config

Audio Monitor

Off, On

IMD Protocol

MEI, Image Video, TSL v4.0, MEI-Image Video

IMD ID #

000-255

IMD Group #

001-254

IMD Name (S/N)

User Defined (16 chars max.)

IMD Baud Rate

300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200

IMD Fixed Align

Center, Right, Left

IMD Fixed Color

Red, Green, Yellow

IMD Fixed Str

User Defined (16 chars max.)

Tally Source

Standard, Image Video HW, Image Video 422, Standard + IV422, TSL/MEI 422

IMD Config

IMD Tally Mode

T1, T2, T1T2, T2T1, T1-, T2-, T1T2-, T2T1-

Serial Chars

Rx, Tx

Serial Errors

P, F, O

Packets

Rec, Exe

Packet Errors

CRC, Err

Last Command

R, E

Main

Service

Software State

000:000 1010111

On-Screen Menu (continued)

MAIN MENU AND NAVIGATION

Access and navigate the main menu using the 4 menu buttons or the RotoMenu™ knob:

Using the menu buttons

• Press the MENU button to enter the main menu.

• Use the ↑

↑↑

↑ and ↓

↓↓

↓ buttons to scroll through the main menu or each submenu.

• Press the SELECT button to enter a submenu or choose a setting.

• Press the MENU button to exit the main menu, or return to the main menu from a submenu.

Using the RotoMenu knob

• Press the RotoMenu™ knob to enter the main menu.

• Rotate the knob to scroll up or down in the main menu or each submenu.

• Press the RotoMenu™ knob to enter a submenu or choose a setting.

The menu automatically times out after 15 seconds of being idle.

Main Menu

On-Screen Menu (continued)

MARKER SETUP SUBMENU

Use the Marker Setup submenu to select various types of markers and settings in 4:3 or 16:9 mode.

■

16:9 Markers

Use this setting to superimpose one of 10 markers on the screen when in 16:9 mode. This setting is disabled when the

aspect ratio is set to 4:3, or when Pixel-to-Pixel mode is enabled.

• Off (No Marker)

• 95% Safe Area

• 93% Safe Area

• 90% Safe Area

• 88% Safe Area

• 80% Safe Area

• 1.85:1 Aspect Ratio

• 2.35:1 Aspect Ratio

• 4:3 Aspect Ratio

• 14:9 Aspect Ratio

• 13:9 Aspect Ratio

16:9 Marker Examples:

OFF (No Marker)

4:3 Aspect Ratio 2.35:1 Aspect Ratio

90% Safe Area

Marker Setup Submenu

On-Screen Menu (continued)

MARKER SETUP SUBMENU (continued)

■

4:3 Markers

Use this setting to superimpose one of 5 markers on the screen when in 4:3 mode. This setting is disabled when the

aspect ratio is set to 16:9, or when Pixel-to-Pixel mode is enabled.

• Off (No Marker)

• 95% Safe Area

• 93% Safe Area

• 90% Safe Area

• 88% Safe Area

• 80% Safe Area

4:3 Marker Examples:

■

Marker Background

Use this setting to choose how selected markers are displayed on the screen:

• Off The marker is superimposed on the complete image.

• 50% Gray Screen area beyond the marker is shown at 50% intensity.

• Black Screen area beyond the marker is shown as black.

Example (80% Marker in 4:3 Mode):

■

Center Marker

Use this setting to display a center marker on the screen.

Center Marker

Background OFF 50% Gray Background Black Background

OFF (No Marker) 90% Safe Area

On-Screen Menu (continued)

VIDEO CONFIGURATION SUBMENU

Use the Video Configuration submenu to select various video settings, such as color temperature, monochrome mode, or

blue-only mode.

■

Monochrome Mode

Use this setting to enable monochrome mode. Only the luminance of the image will be displayed as a grayscale

picture.

■

Blue-Only Mode

Use this setting to enable Blue-Only mode. This mode displays only the blue color component of the image, switching

off the red and green components. Use this mode when calibrating the monitor to SMPTE color bars with the following

procedure:

1. Allow the monitor to warm up for at least 5-10 minutes.

2. Display SMPTE split-field color bars on the monitor using an external source.

3. Enable Monochrome mode.

4. Locate the pluge pattern (super black, black, and gray bars) at the lower-right corner of the screen. Adjust the Brightness knob until there is

no visible difference between the super black and black bars, but the gray bar is still visible.

5. Adjust the Contrast knob until an even grayscale appears along the top bars.

6. Disable Monochrome mode.

7. Enable Blue-Only mode and adjust the Color knob so that the outermost bars (white and blue) appear to match in brightness.

Video Configuration Submenu

On-Screen Menu (continued)

VIDEO CONFIGURATION SUBMENU (continued)

■

Pixel-to-Pixel Mode

Use this setting to enable Pixel-to-Pixel mode.

This mode bypasses the monitor’s internal scaling function and displays incoming images in their native resolution and

aspect ratio, with a one-to-one mapping of incoming image pixels to screen pixels:

• For incoming formats smaller than the native resolution of the screen (or selected aspect ratio), the image will be

displayed in the center of the screen using only the necessary LCD pixels. For example, NTSC or PAL images will

occupy exactly 720 x 486 or 720 x 576 pixels respectively. The surrounding screen area will be black.

• For incoming formats exceeding the screen resolution (or selected aspect ratio), only the center portion of the

incoming image will displayed, with the remainder of the picture cropped. For example, 1080i/p formats will both

be cropped to 1024 x 768, or 1024x576, depending on the selected aspect ratio.

■

Aspect Ratio Settings

Use this menu option to switch between several aspect ratio settings

As the V-R653-IMD-TE monitor has a native resolution of 1024 x 768 RGB pixels, incoming images are automatically

scaled to fit the screen:

• In 4:3 mode, images are scaled up or down to fill the entire 4:3 screen (1024 x 768). IMD text, tally, time code,

and audio presence indicator are superimposed on the lower portion of the image.

• In Scaled 4:3 mode, images are scaled to a smaller 4:3 portion of the screen, leaving space for IMD text to be

displayed below the image. Time code and the audio monitor icon are superimposed on the image.

• In 16:9 mode, images are scaled to fill the maximum 16:9 portion at the top of the screen (1024 x 576). In this

mode, IMD text, tally, time code, and the audio monitor icon are shown in the black area at the bottom of the

screen, without overlapping the image.

• In 16:9 Centered mode, images are scaled to fill the maximum 16:9 portion in the center of the screen (1024 x

576), with black bars filling the remainder of the screen. In this mode, IMD text is shown below the image, and

time code is shown above. The audio monitor icon is superimposed on the lower left of the image.

The diagrams on the following page show how IMD text, timecode, and the audio monitor icon are simultaneously

displayed on the screen in each aspect ratio setting. The white area represents the video image.

On-Screen Menu (continued)

VIDEO CONFIGURATION SUBMENU (continued)

■

Aspect Ratio Settings (continued)

■

Curtain Color

Use this setting to choose the default color displayed on the screen when no video input is present. Available colors

are blue, red, green, white, and black.

4:3 Mode

16:9 Mode

16:9 Centered Mode

Scaled 4:3 Mode

On-Screen Menu (continued)

COLOR CONFIGURATION SUBMENU

Use the Color Configuration submenu to adjust the color temperature of the display.

■

Ctemp/Gamma

Use this setting to choose one of three color temperature / gamma presets:

• D55 (5500K)

• D65 (6500K)

• D93 (9300K)

• Linear (No gamma applied)

■

Red, Green, and Blue Offset

Use the offset controls for red, green, and blue to adjust the color temperature of the display. Each setting adjusts the

offset, or brightness, of each individual color component. These settings will affect whichever color temperature preset

is selected.

• Red (0-100)

• Green (0-100)

• D93 (0-100)

■

Red, Green, and Blue Gain

Use the gain controls for red, green, and blue to adjust the color temperature of the display. Each setting adjusts the

gain, or contrast, of each individual color component. These settings will affect whichever color temperature preset is

selected.

• Red (0-100)

• Green (0-100)

• D93 (0-100)

Color Configuration Submenu

On-Screen Menu (continued)

SYSTEM CONFIGURATION SUBMENU

Use the System Configuration submenu to control various system parameters.

■

Gray Levels

Use the Gray Levels menu option to view 256 levels of flat field gray. This feature is useful for color temperature

comparison and calibration. The input must be disconnected for the Gray Levels feature to function.

■

User-Definable Function Buttons

Use the Function 1 and Function 2 menu items to define each function button on the front panel of the monitor. The

following options are available for each button:

• Marker Enable and rotate amongst marker settings (choices depend on aspect ratio setting)

• Center Marker Enable/disable center marker

• Marker Backgrd Rotate amongst marker backgrounds

• IMD Display/hide IMD text

• Time Code Display/hide time code

• OSD Tally Rotate amongst types of OSD Tally

• Audio Monitor Display/hide audio presence indicator

• Aspect Ratio Toggle between 4:3 and 16:9 aspect ratios

• Pixel to Pixel Enable/disable Pixel-to-Pixel mode

• Ctemp/Gamma Rotate amongst color temperature settings

• Blue Only Enable/disable Blue Only mode

• Monochrome Enable/disable Monochrome mode

System Configuration Submenu

On-Screen Menu (continued)

SYSTEM CONFIGURATION SUBMENU (continued)

■

Saving and Loading User Presets

Use the SAVE CONFIG and LOAD CONFIG menus to save current settings to one of 6 presets, or load a preset. Each

Preset saves all monitor settings except for IMD configuration.

• Use the LOAD CONFIG menu to load one of presets USR1 – USR6. Factory default settings can also be loaded

by selecting MFG. (Factory defaults cannot be overwritten.)

• Use the SAVE CONFIG menu to save the current settings to a preset from USR1- USR6.

■

Save Defaults

Use this setting to save the current values of the Color, Brightness, and Contrast controls as the default values. The

defaults can then be accessed by pushing the knob twice.

• Back Exit without making any changes

• Save Save current settings as defaults

• Mfg Return to the manufacturer’s defaults (all settings at 50).

■

Software Version Display

The Main Board, Keypad, and CPLD software version numbers are displayed.

On-Screen Menu (continued)

DEINTERLACER SUBMENU

Use the Deinterlacer submenu to control the type of deinterlacing performed on interlaced input signals.

■

Deinterlacer Mode

User the Deinterlacer Mode option to set the type of deinterlacing algorithm used:

• In Auto mode, the deinterlacer defaults to Motion Adaptive mode (see below), but uses Film Mode (see below)

whenever a film cadence is detected. This is the optimum deinterlacing mode for best picture quality and should

be used whenever possible.

• In Motion Adaptive mode, the image processor uses a motion adaptive de-interlacing algorithm. Film cadence

detection is disabled. Motion adaptive interlacing uses a variety of real-time algorithms to perform the best

possible deinterlacing based on the content.

• In Field to Frame, each incoming field is scaled to a full progressive frame by the scaler. It is normal for the

image to appear vertically “bouncy” or as shaking.

• In Interpolate (Bob) mode, each field is scaled to a full progressive frame by interpolating the missing lines from

the adjacent lines. It is normal for the image to appear vertically “bouncy” or as shaking.

• In Static Mesh (Weave) mode, the Deinterlacer combines or “weaves” each pair of fields into a progressive

frame. It is normal to see jagged artifacts on fast-moving edges.

System Configuration Submenu

On-Screen Menu (continued)

DEINTERLACER SUBMENU (continued)

■

Film Mode

Film mode uses specialized algorithms to correctly deinterlace content that originated in either 24fps or 25fps. Film

Mode is automatically entered whenever a film-to-video cadence is detected in the content. Film cadence detection is

active whenever the Deinterlacer Mode is set to Auto.

Use the Film Mode setting to limit the film mode detection to a specific cadence.

• Auto Deinterlacer automatically identifies the film cadence

• 2:2 only Deinterlacer only recognizes content originating in 25fps, and uses 2:2 film mode. 24fps content is ignored.

• 3:2 only Deinterlacer only recognizes content originating in 24fps, and uses 3:2 film mode. 25fps content is ignored.

■

Film Indicator

Use the Film Indicator setting to enable or disable the film mode detection icon. If the Film Indicator is set to On, a

green square will appear in the top left corner of the screen whenever a film cadence is detected. The Film Indicator

can only be turned on only when the Deinterlacer Mode is set to Auto. It is normal for the Film Indicator to sporadically

turn on and off, depending on the content.

■

Motion Display

Use the Motion Display options to display inter-field motion as false color (green) on the screen. This feature is used to

visualize how the deinterlacer is detecting motion in the content. It is normal for the screen to show large portions of

green when viewing moving images.

• Off Motion Display is off.

• Noise Pixels which change value between fields are displayed as green.

• Motion After a noise reduction filter, pixels which change value between fields are displayed as green.

On-Screen Menu (continued)

OSD CONFIGURATION SUBMENU

Use the OSD Configuration submenu to select a variety of information to be displayed on the screen.

■

IMD State

Use this setting to turn the IMD text display on or off. This setting affects both fixed string IMD text and remote IMD text

commands (see IMD Configuration Submenu for details – page 22).

■

Status Display

Use this setting to enable or disable status display. When enabled, the current video input standard is displayed on the

top left of the screen. When disabled, status is only displayed for 2 seconds when the monitor is powered on, when an

input is applied, or when the input video standard changes. The status display reads “No Input” when no video input is

present.

OSD Configuration Submenu

Status Display

On-Screen Menu (continued)

OSD CONFIGURATION SUBMENU (continued)

■

OSD Tally

Use this setting to choose how tally is displayed on the screen. The available OSD Tally options depend on the Tally

Source selected in the IMD Configuration submenu (see page 22).

When the Tally Source is set to Standard (contact closure), OSD Tally can be set to Off, RGY, RG, or GR:

• Off On-screen tally is disabled

• RGY Red, yellow, or green tally signals are indicated at both the bottom left and bottom right corners of the

screen. Two or three colors are shown simultaneously by subdividing each tally indicator

• RG Red tally is shown at the bottom left of the screen, and green is shown at the bottom right.

• GR Green tally is shown at the bottom left of the screen, and red is shown at the bottom right.

The following diagrams show RGY, RG, and GR OSD Tally modes:

When the Tally Source is set to TSL/MEI 422, OSD Tally can be set to Off or IMD:

• Off On-screen tally is disabled

• IMD Red, yellow, and green tally is displayed according the protocol commands. Green, red, and yellow colors

are shown individually on either the bottom left or right of the screen.

RGY mode: single color activated

RGY mode: two colors activated

RGY mode: three colors activated

GR Mode: both colors activated

RG Mode: both colors activated

Page is loading ...

Marshall electronic V-R653-IMD-TE User manual

Brand: Marshall electronic

Model: V-R653-IMD-TE

Type: User manual

This manual is also suitable for

Computer Monitor V-R653-IMD-TE

Download PDF

report

Marshall electronic V-R653-IMD-TE User manual

This manual is also suitable for

Marshall electronic V-R653-IMD-TE User manual

Related papers

Other documents