ELECTRIC COOKER
ESC 5061 W
GB
2
3
CONTENTS
Instructions for the user Instructions for the installer
Important Safety Information
Description of the appliance
Operation
- Electric hotplates
- Hints & Tips
- Using the electric oven
- Using the electric grill
- Hints & Tips
Maintenance and Cleaning
Something Not Working
Service & Spare Parts
Customer Care
Guarantee conditions
4
5
6
6
7
8
9
10
12
14
15
15
16
Technical features
Important safety requirements
Location
Electrical connections
17
18
18
19
How to read the instruction book
The symbols below will guide you when reading the
instruction book
Safety instructions
Step by Step Operation
Advice and recommendations
Environmental Information
4
IMPORTANT SAFETY INFORMATION
Installation
• This cooker must be installed by qualified
personnel, according to the manufacturer’s
instructions and to the relevant British
Standards.
• This cooker is heavy. Take care when
moving it.
• Remove all packaging before using the
cooker.
• Ensure that the electrical supply complies
with the type stated on the rating plate.
• Do not attempt to modify the cooker in any
way.
Child Safety
• This cooker is designed to be operated by
adults. Do not allow children to play near or
with the cooker.
• The cooker gets hot when it is in use.
Children should be kept away until it has
cooled.
• Children can also injure themselves by
pulling pans or pots off the cooker.
During Use
• This cooker is intended for domestic cooking
only. It is not designed for commercial or
industrial purposes.
• Do not use this cooker if it is in contact with
water. Do not operate the cooker with wet
hands.
• The grill pan will become hot during use,
always use oven gloves when removing or
replacing a hot grill pan.
• Ensure the control knobs are in the ‘OFF’
position when not in use.
• When using other electrical appliances,
ensure the cable does not come into contact
with the hot surfaces of the cooker.
• Unstable or misshapen pans should not be
used on the hob burners as unstable pans
can cause an accident by tipping or spillage.
• Never leave the cooker unattended when
cooking with oil and fats.
• This cooker should be kept clean at all
times. A build-up of fats or foodstuffs could
result in a fire.
• Never use plastic dishes in the oven or on
the hob hotplates. Never line any part of the
oven with aluminium foil.
• Always ensure that the oven vent, which is
located at the centre back of the hob, is left
unobstructed to ensure ventilation of the
oven cavity.
• Perishable food, plastic items and aerosols
may be affected by heat and should not be
stored above the cooker.
Service
• This cooker should only be repaired or
serviced by an authorised Service Engineer
and only genuine approved spare parts
should be used.
Environmental Information
• After installation, please dispose of the
packaging with due regard to safety and the
environment.
• When disposing of an old appliance, make it
unusable, by cutting off the cable.
You MUST read these warnings carefully before installing or using the appliance. If you
need assistance, contact our Customer Care Department on 08705 950950.
Keep this instruction book for future
reference and ensure it is passed
on to
any new owner.
5
DESCRIPTION OF THE APPLIANCE
n
n
Control panel
Oven door with
glass
Door handle
Adjustable
small feet
Hob
1500W
1000W
1000W
2000W
1
2
3
4
1. Hot plate ∅ 145 – 1000W
2. Hot plate ∅ 180 – 1500W
3. Hot plate ∅ 145
– 1000W
4. Hot plate ∅ 180 – 2000W
Control panel
Model : ESC 5061 W
4 5 6
7
1
ESC 5061 W
THERMOSTAT
MAIN
250
200
150
100
50
2
1
3
4
5
6
0
2
1
3
4
5
6
0
2
1
3
4
5
6
0
2
1
3
4
5
6
0
23
0
1. Oven function control knob
2. Oven thermostat pilot light
3. Main pilot light
4. Front left hotplate control knob
5. Back left hotplate control knob
6. Back right hotplate control knob
7. Front right hotplate control knob
6
OPERATION
Electric Hotplates
To switch on a hotplate, turn the relevant control
knob to the required heat setting.
The control knob is numbered 0 – 6
0 – OFF
1 – Minimum
6 – Maximum.
The hob has two types of hotplates:
Normal Hotplates
We recommend the plates are switched to
maximum (6) for a short while to boost the plate,
and then adjusted to the required setting.
Rapid Hotplate (Front right)
The rapid hotplates indicated by a red spot, will
heat up more quickly than a normal plate.
Over a period of time the red spot may
disappear, this will not affect the
performance of the hotplate.
It is important to note that the hotplate
may smoke and produce a slightly
unpleasant odour when used for the first
time. This is quite normal and will
disappear after some time.
Suggestions for the correct setting of the plates
are given in the following table:
2
1
3
4
5
6
0
OFF
0
Very Gentle
1
To keep food warm
To melt butter and chocolate
Gentle
2
To prepare cream-sauces,
stews and milk puddings or to
fry eggs
Slow
3
Dried vegetables, frozen food,
fruit, boiling water or milk
Medium
4
Boiled potatoes, fresh
vegetables, pâtés, soups,
broths, pancakes or fish
High
5
Larger stews, meat roll, fish,
omelettes, steaks
Fast
6
Steaks, escalopes and frying
7
Hints and Tips
Saucepans for use on solid plates should have
several characteristics:
- They should be fairly heavy duty
- They should fit the heat area exactly, or be
slightly larger for efficient use, NEVER
smaller.
- They should have a flat base to ensure good
contact with the plate.
This is particulary important when using pans
for high temperature frying or pressure
cooking.
As soon as liquid starts boiling, turn down the plate
control knob so that it will barely keep the liquid
simmering.
You can switch off the plate a short while before
you finish cooking, and the final stage will be
completed on the accumulated heat. Similarly,
stews etc. cooked in well covered saucepans cook
at lower temperature which is more economical.
Ensure pans are large enough to avoid
liquids being split into the plates. Never
leave the plates on without a pan on them
or with an empty pan on them.
Take care never to lean or reach over a
hot electric plate. Always point pan
handles inward or over the work surface
next to the hob to avoid accidentally
knocking over a pan as you pass by.
Take care when frying food in hot oil or
fat, as the overheated splashes could
easily ignite.
If the control knobs become difficult to
turn, please contact your local Electrolux
Service Centre.
Good use
Bad use
(Power waste)
8
Using the electric oven
Before the first use ensure that the
room is well ventilated: V.M.C.
(Mechanic ventilation) or opened
window.
Before the First Use of the Cooker
Remove all packaging both inside and
outside of the cooker, before using it.
Before first use, the oven should be heated
without food. During this time, an unpleasant
odour may be emitted. This is quite normal.
1. Remove the oven accessories.
2. Remove any adhesive labels or protective
films, if there are any.
3. Turn the thermostat control knob to 250ºC
and heat the oven for about 45 min.
This procedure should be repeated with the grill
function for approximately 5-10 minutes.
Clean the accessories with a soft detergent. Rinse
and dry carefully.
During cooking, the oven door is hot.
Take care that children do not play
near it.
The electric oven is equipped with 3 heating
elements:
- 2 heating elements (top and bottom) for
using the oven.
- 1 heating grill element, placed in the middle
of top for grilling with door half opened.
Use
The oven can be used in traditional cooking or
for grilling, but not simultaneously.
Control knob
The control knob is used to select the desired
temperature and to select either the grill or oven
function.
Explanations of symbols:
0
Off positions
50-250 Temperature selection (bottom and top
heat)
Grill
To select the temperature turn the knob
clockwise until the pointer indicating the desired
temperature between 50º – 250ºC.
The temperature will be kept constant by the
thermostat.
250
200
150
100
50
0
9
Cooking in the oven
Traditional cooking
Traditional cooking is made by natural convection
the heated air.
It is necessary to pre-heat the oven.
How to proceed ?
For small cakes, pastry, Victoria sandwich.
1. Preheat the oven the thermostat on position
chosen for cooking:
- about 8 min. for position 50°C to 150°C;
- about 15 min for position 175°C to 250°C;
2. Insert the meal
Using the electric grill
Electric grill
When grilling, the accessible parts of the
appliance are hot and the appliance should not
be left unattended. Take care that children do
not play near it. While the grill is operating
leave the oven door half open and put the grill
deflector “A” into place. During use the
appliance becomes hot. Care should be taken
to avoid touching heating elements inside the
oven,or the grill deflector.
The grill pan will become hot during use,
always use oven gloves when removing or
replacing a hot grill pan.
The grill is used for grilling all kind of meat which
remain tender, toast or browning dishes already
cooked.
Slide the dripping pan under the grid on the
lowest shelf to collect the juice and fat.
For turning off the heating elements.
Turn the knob clockwise to position off “0”.
Grilling
Heat comes from the top of the oven. It is suitable
for grilling meat (beef bacon, pork bacon …) that
remains tender, for toast or to brown already
cooked.
When using the grill it has to be
supervised, half open and pull the protective
screen “A” into place.
Grilling
• Prepare the meat to be grilled, lightly brush it
with oil on both sides.
• Place it on the trivet.
• Put the grill deflector in place.
• Turn the oven knob to the grill position
.
• Put the dripping pan in the level 1.
• Slide the shelf into level 2 or 3 depending on
the thickness of the meat to be grilled.
• Use level 3 for the thin pieces to be roasted
A
1
2
3
10
(toasts, pork bacon, sausage, small fish…)
• Use level 2 for thick pieces of meat to be
grilled (beef bacon, large fish, poultry).
• When the first side is brown, turn the meat
without pricking it in order that the juices are
not lost.
• Grill the second side.
• Salt when ending the cooking.
Cooking time has to determined by the thickness
of the piece to be grilled not by its weight.
Browning
• Fix the grill deflector.
• Turn the oven knob to the grill position
.
• Place the dish on the grid and slide it in level 2
or 3.
• Leave the dish under the radiation of the grill
for a few minutes.
Cooker operation pilot light (Main)
This light will illuminate when any of the hotplate
knobs are turned on and remains lit while the
hotplates are in use.
Oven thermostat pilot light
This light will illuminate when a temperature is
selected and remain lit until the selected
temperature has been reached. It then cycles on
and off to indicate that the temperature is being
maintained.
Hints and Tips
Condensation and steam
When food is heated it produces steam in the
same way as a boiling kettle. The oven vents
allow some of this steam to escape. However,
always stand back from the oven when
opening the oven door to allow any build up of
steam or heat to release.
If the steam comes into contact with a cool
surface on the outside of the oven, e.g. a trim, it
will condense and produce water droplets. This
is quite normal and is not a fault with the oven.
To prevent discolouration, regularly wipe away
condensation and also soilage from surfaces.
Cookware
Use any ovenproof cookware, which will
withstand temperatures of 250
°
C.
Oven dishes, etc. must not be placed directly
on the oven base.
1
2
3
11
Oven Cooking
• Turn off the oven 5 minutes before the end of
cooking time, and use residual heat to
complete the cooking.
• The thickness, the material and the colour of
the pan will influence the cooking results.
• When cooking, certain dishes increase in
volume, ensure the pan is large enough.
• To prevent fat dripping when roasting use tall
rim pans proportional to the item being
roasted.
• Prick the skin of poultry and sausages with a
fork before cooking to avoid spitting.
Use heatproof glass dishes for soufflés.
The effects of dishes on cooking results
Dishes and tins vary in their thickness,
conductivity, colour, etc. which affects the way
they transmit heat to the food inside them.
A Aluminium, earthenware, oven glassware
and bright shiny utensils reduce cooking and
base browning.
B Enamelled cast iron, anodised aluminium,
aluminium with non-stick interior and
coloured exterior and dark, heavy utensils
increase cooking and base browning.
Accessories delivered with the
appliance
The following accessories are supplied with your
appliance.
• 1 trivet
• A dripping pan / roasting tray with
roasting grid in it.
A grill deflector
In addition to the accessories supplied we
recommend you only use heatproof dishes/pans
(according to the manufacturer'instructions).
12
MAINTENANCE AND CLEANING
Before any maintenance or cleaning
can be carried out, you must
DISCONNECT the cooker from the
electricity supply.
Cleaning materials
Before using any cleaning materials on your
oven, check that they are suitable and that their
use is recommended by the manufacturer.
Cleaners that contain bleach should
NOT be used as they may dull the
surface finishes. Harsh abrasives
should also be avoided.
External cleaning
Regularly wipe over the control panel, oven door
and door seal using a soft cloth well wrung out in
warm water to which a little washing up liquid
has been added.
To prevent damaging or weakening the
door glass panels avoid the use of the
following:
• Household detergent and bleaches
• Impregnated pads unsuitable for non
stick saucepans
• Brillo/Ajax pads or steel wool pads
• Chemical oven pads or aerosols
• Rust removers
• Bath/Sink stain removers
Oven Door
- The door can be dismantled for cleaning as
follows:
- Open the door completely
- Revolv the two locking parts on the hinge
arms completely upwards.
- Partially close the door, to a 30
o
angle
- Lift the door and pull out
The internal
oven door glass can be
removed for cleaning. For this purpose
remove the 2 fixing screws.
Clean the outer
and inner
door glass using warm soapy
water. Should the inner door glass become
heavily soiled it
is recommended that a
cleaning product such as Hob Brite, or Bar
Keepers Friend be used.
Always support the door while removing the
glass panel as the door may spring closed due
to its lighter weight.
locking parts
DO NOT clean the oven door while the
glass panels are warm. If this
precaution is not observed the glass
panel may shatter.
If the door glass panel becomes
chipped or has deep scratches, the
glass will be weakened and must be
replaced to prevent the possibility of
the panel shattering.
Contact your local Service Centre who
will be pleased to advise further.
IMPORTANT: The inner door glass must be in
place when using the oven.
13
Oven Cavity
The enamelled oven cavity is best cleaned
whilst the oven is still warm.
Wipe the oven over with a soft cloth soaked in
warm soapy water after each use. From time to
time it will be necessary to do a more thorough
cleaning, using a proprietary oven cleaner.
The Hob Top
The hob is best cleaned whilst it is still warm, as
spillage can be removed more easily than if it is
left to cool.
Regularly wipe over the hob top using a soft
cloth well wrung out in warm water to which a
little washing up liquid has been added. Avoid
the use of the following:
• household detergent and bleaches;
• impregnated pads unsuitable for non-stick
saucepans;
• steel wool pads;
• bath/sink stain removers.
Should the hob top become heavily soiled, it is
recommended that a cleaning product such as
Hob Brite or Bar Keepers Friend is used.
The Hotplates
Spills onto the actual plate should be removed
using warm water and a soft brush, nylon or
plastic scourer. To keep the plates looking as new,
hotplate conditioner can be purchased from most
hardware stores, e.g. “4 Hob” by HomeCare
Products (follow the manufacturer’s instruction for
use).
Alternatively, wipe the plates with a drop of olive oil
on a kitchen towel to avoid rust. It is important to
note that the plate will smoke a little and produce a
slightly unpleasant odour when next used.
Drying
Important: After cleaning, dry the hotplates
thoroughly by switching on to a low-medium
setting for a few minutes.
Restoring
To maintain the appearance of your sealed
hotplates apply a little salt-free vegetable oil or
restorative agent (i.e. :Collo Electrol”, or Minky
Hotplate Cleaning Cloths) periodically.
To apply vegetable oil: first heat the hotplate on
a medium setting for 30 seconds then turn off.
Pour a very small amount of salt-free oil onto a
dry cloth or kitchen paper. Apply a thin coat of oil
to the hotplate surface and wipe off any excess.
Heat the hotplate on a medium setting for 1
minute.
To apply restorative agent: first heat the hotplate
on a medium setting for 30 seconds then turn
off. Apply a very thin coating of Collo Electrol
(using the applicator). Heat a hotplate on a high
setting for 2-3 minutes to cure. Some smoke will
occur, this is normal and nontoxic. (NB: this
product is a restorative agent not a cleanser. It is
available from hardware stores).
Stainless steel parts: the stainless steel spill
rings may become straw coloured with use. Use
a proprietary stainless steel cleaner to remove
this straw discolouration. This also applies to the
area around the hotplates on stainless steel
hobs.
14
SOMETHING NOT WORKING
If the appliance is not working correctly, please carry out the following checks, before contacting your
local Service Force Service Centre.
IMPORTANT: If you call out an engineer to a fault listed below, or to repair a fault caused by
incorrect use or installation, a charge will be made even if the appliance is under guarantee.
Symptoms Solutions
The hob hotplate does not heat up Check:
- that the unit is connected and the electrical
supply is switched on
- the mains fuse has not blown
- the correct control knob has been turned.
The hotplate is not giving satisfactory results Check:
- the hotplate is clean and dry
- the pan is the correct size for the hotplate
- the pan has a flat bottom
- the setting is correct for the type of cooking.
The oven does not come on Check:
- check if a cooking function/temperature has
been selected correctly
- the socket switch or the switch from the mains
supply to the cooker are ON.
It takes too long to finish the dishes, or they
are cooked too fast
Check:
- the temperature may need adjusting
Steam and condensation settle on the food
and the oven cavity
- refer to the contents of this booklet, especially to
the chapter “Using the Oven”.
- Leave dishes inside the oven no longer than 15-
20 minutes after the cooking is completed.
If after these checks, the appliance still does not operate correctly, contact your local Service Force
Centre. When you contact the Service Force Centre you will need to give the following details:
1. Your name, address and post code.
2. Your telephone number
3. Clear and concise details of the fault
4. The model and serial number of the appliance (found on the rating plate*)
5. The purchase date
* The rating plate can be found on the lower left hand corner of the front frame of the cavity.
Please note that a valid purchase receipt or guarantee documentation is required for in-guarantee
service calls.
15
SERVICE AND SPARE PARTS
In the event of your appliance requiring service, or if you wish to purchase spare parts, please contact
your local Service Force Centre by telephoning:-
08705 929929
Your telephone call will be automatically routed to the Service Force Centre covering your post code area.
For the address of your local Service Force Centre and further information about Service Force, please
visit the website at www.serviceforce.co.uk
Before calling out an engineer, please ensure you have read the details under the heading “Something
Not Working” and have the model number and purchase date to hand.
In-guarantee customers should ensure that the checks under the heading “Something Not
Working” have been made as the engineer will make a charge if the fault is not a mechanical or
electrical breakdown. Please note that it will be necessary to provide proof of purchase for any in-
guarantee service calls.
Moffat has an agreement with Electrolux who will undertake all servicing requirements for your appliance.
CUSTOMER CARE
For general enquiries concerning your Moffat appliance and or for further information on our products,
contact our Customer Care Department by letter or telephone as follows:
Customer Care Department
Moffat
55-77 High Street
Slough
Berkshire
SL1 1DZ
Tel: 08705 950 950 (*)
(*) calls to this number may be recorded for training purposes.
16
GUARANTEE CONDITIONS
Standard Guarantee Conditions
We Moffat undertake that if, within 12 months of the date of the purchase, this Moffat appliance or any
part thereof is proved to be defective by any reason only of faulty workmanship or materials, we will, at
our option, repair or replace the same FREE OF ANY CHARGE for labour, materials or carriage on
condition that:
• The appliance has been correctly installed and used only on the electricity supply stated on the rating
plate.
• The appliance has been used for normal domestic purposes only, and in accordance with the
manufacturer's instructions.
• The appliance has not been serviced maintained, repaired, taken apart or tampered with by any
person not authorised by us.
• All service work under this guarantee must be undertaken by an Electrolux Service Force Centre.
• Any appliance or defective part replaced shall become the Company's property.
• This guarantee is in addition to your statutory and other legal rights.
Home visits are made between 8.30am and 5.30pm Monday to Friday. Visits may be available outside
these hours, in which case a premium will be charged.
Exclusions
This guarantee does not cover:
• Damage or calls resulting from transportation, improper use or neglect, the replacement of any light
bulbs or removable parts of glass or plastic.
• Costs incurred for calls to put right an appliance which is improperly installed or calls to appliance
outside the United Kingdom.
• Appliances found to be in use within a commercial or similar environment, plus those, which are the
subject to rental agreements.
• Products of Moffat manufacture which are not marketed by Moffat.
European Guarantee
If you should move to another country within Europe then your guarantee moves with you to your new
home subject to the following qualifications:
• The guarantee starts from the date you first purchased your product.
• The guarantee is for the same period and to the same extent for labour and parts as exist in the new
country of use for this brand or range of products.
• This guarantee relates to you and cannot be transferred to another user.
• Your new home is within the European Community (EC) or European Free Trade Area.
• The product is installed and used in accordance with our instructions and is only used domestically,
i.e. a normal household
• The electrical supply complies with the specification given in the rating label.
• The product is installed taking into account regulations in your new country.
Before you move, please contact your nearest Customer Care Centre, listed below, to give them details of
your new home. They will then ensure that the local Service Organisation is aware of your move and able
to look after you and your appliances.
France Senlis +33 (0) 3 44 62 20 13
Germany Nürnberg +49 (0) 800 234 7378
Italy Pordenone +39 (0) 800117511
Sweden Stockholm +46 (0) 20 78 77 50
UK Slough +44 (0) 1753 219898
17
INSTRUCTIONS FOR THE INSTALLER
TECHNICAL FEATURES
Free standing Class X
Hob Front right
Back right
Front left
Back left
Hot plate ∅ 180mm (rapid)
Hot plate ∅ 145mm (normal)
Hot plate ∅ 145mm (normal)
Hot plate
∅ 180mm (rapid)
2000W
1000W
1000W
1500W
Total rating 5500W
Oven
Oven
Oven power
Grill
Grill power
Electric
1700W
Electric
1800W
Total rating 1800W
Accessories
Oven grid
Roasting tray
Roasting grid
Protective screen
Chromed
Enamelled
Chromed
Enamelled
Supply
Rated voltage
Rated frequency
240/415V
50 Hz
Total rating 1800W
Dimensions Height to the hob
Width
Depth
880 - 890 mm
500 mm
600 mm
This appliance complies with the following EEC
Directives :
73/23 - 90/683 ; (Low Voltage Directive) and
subsequent modifications,
89/336 (Electromagnetical Compatibility
Directive)
93/68 (General Directives) and subsequent
modifications.
18
IMPORTANT SAFETY REQUIREMENTS
Important
This cooker must be installed in
accordance with the IEE Wiring Regulations
(Current Edition). Detailed recommendations
are contained in the following British
Standards Codes Of Practice:
B.S. 6172/ B.S. 5440, Par.2 and B.S. 6891
Current Editions.
LOCATION
The cooker has been registered as a “Class X”
appliance according to Fire Risk Regulations.
Any adjacent cabinets or walls must not exceed
the cooker’s height.
The cooker may be located in a kitchen, a
kitchen/diner or bed sitting room, but not in a
bathroom, shower room or garage.
The minimum distance combustible material can
be fitted above the cooker in line with the edges
of the cooker is 660mm (see fig.)
Levelling
Fix the support with two legs with the washer and
nuts, delivered with the cooker, see the figure.
• Unscrew the legs as far as possible (approx.
16mm from fully screwed in).
• Place the plinth (pos.3) so that the springs
(pos.2) reach the threaded area of the legs
and the clamp of the plinth (pos.4) is in front
of the holes (pos.5) on the under side of the
structure.
• Push the plinth towards the appliance with
both hands until the springs fasten on the legs
and the clamps go into the corresponding
holes.
• Adjust the legs as necessary.
610 mm
C
2
1
3
4
5
6
7
8
G
150 mm
660 mm
1
3
2
5
4
19
ELECTRICAL CONNECTIONS
Important
Any electrical work required to install
this cooker should be carried out by a
qualified electrician or competent person, in
accordance with the current regulations.
THIS COOKER MUST BE EARTHED
The manufacturer declines any liability
should these safety measures not be
observed.
This cooker is designed to be connected to a
240V, 50Hz electrical supply.
To connect to the electricity supply, use cable
type H05 RR-F.
Before connection, make sure the electricity
supply voltage is the same as that indicated on
the rating plate.
The cooker is supplied without supply cable. A 3
core flexible supply cord must be fitted, in
accordance with the specification given in the
table no.1.
The electrical connection should be made using
a double pole isolating switch (cooker control
switch) with at least 3mm contavt separation in
all poles. The cable must have conductors of
sufficiently high cross-sectional area to prevent
overheating or deterioration.
The switch should be sited within 2m of the
cooker and be easily accessible at all times.
The yellow-green earth wire must not to be
interrupted by the switch.
Ensure that the cooker supply cable
does not come into contact with surfaces
with temperatures higher than 50 °C.
Table no.1
Connection type Single phase (UK)
Cable connection to the
terminal block
1 2 3 4 5
L1
N PE
Mains Voltage
240 V
Voltage of heating
elements
240 V
Fuse capacity
32 A
Cable section
3x6 mm
2
NOTE: The earth wire should be about 2 cm
longer than the live and neutral wires.
Before connecting check that:
• The fuse and household electrical installation
can carry the absorbed current of the
appliance (see rating plate);
• The cooker connection outlet or the cooker
control switch is easily accessible when the
appliance is installed.
How to proceed?
• Unscrew and remove the protective cover at
the back of the appliance;
• Connect the power cable to the terminal
block of the cooker according to the table
no.1;
• Secure by means of cable clamp;
• Make sure that the connection to the terminal
block is matching the supply system, see
table no.1;
• Refit and screw the protective cover on the
back of the appliance.
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
Moffat ESC5061S User manual
- Category
- Kitchen & houseware accessories
- Type
- User manual
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
Other documents
-
Tricity Bendix SE211X User manual
-
Tricity Bendix SE211X User manual
-
Tricity Bendix CSIE232GR User manual
-
Tricity Bendix CSIE 231 User manual
-
Whirlpool AKM 302 IX User guide
-
Electrolux EHE30200X User manual
-
Zanussi ZCM564NW1 User manual
-
-
Electrolux EHE320X User manual
-
