Baumatic BES900BGL - 36900540 User manual

my

BES900BGL

90 cm Glass Chimney

Hood

User Manual for your Baumatic

BES900BGL

90 cm Glass Chimney hood

NOTE: This User Instruction Manual contains important

information, including safety & installation points, which will

enable you to get the most out of your appliance. Please keep it

in a safe place so that it is easily available for future reference; for

you or any person not familiar with the operation of the appliance.

GS 13/05/13

2

3

Contents Page

Environmental note 4

IMPORTANT SAFETY INFORMATION 5 – 7

Specifications of your cooker hood 8 – 9

Product dimensions 8

Specifications 8

Using your cooker hood 9 – 11

Setting the time of day 9

Light control 9 – 10

Speed selection 10

The cut-off timer 10 - 11

Cleaning your Baumatic cooker hood 11

Cleaning 11

The grease filters 11

Maintenance 12 - 15

Removing and cleaning the grease filters 12

Changing a light bulb 13 - 14

Fitting the carbon filter 14 - 15

Installation 15 - 25

Electrical connection 16

Before beginning installation 16 - 17

Extraction mode or recirculation mode? 18

Installing your cooker hood 18 - 21

Connecting to external ducting 22

Fitting the chimney 22 – 24

Completing the installation 25

Troubleshooting 25 – 26

Baumatic consumables 27

Contact details 31

ENVIRONMENTAL NOTE

Note: Before discarding an old appliance, switch off and

disconnect it from the power supply. Cut off and render any

plug useless. Cut the cable off directly behind the appliance to

prevent misuse. This should be undertaken by a competent

person.

CONFORMITY TO W.E.E.E. DIRECTIVE

4

IMPORTANT SAFETY INFORMATION

Your safety is of the utmost importance to Baumatic.

Please make sure that you read this instruction booklet

before attempting to install or use the appliance. If

you are unsure of any of the information contained in

this booklet, please contact the Baumatic Advice Line.

IMPORTANT: Any installation work must be

carried out by a qualified electrician or

competent person.

o The hood must be installed in accordance with the installation

instructions and all measurements followed.

o If the cooker hood is installed for use above a gas appliance then

the provision for ventilation must be in accordance with the Gas

Safety Codes of Practice BS.6172, BS.5440 & BS.6891 (Natural

Gas) and BS.5482 (LP Gas) 1994, the Gas Safety (Installation &

Use) Regulations, the Building Regulations issued by the

Department of the Environment, the Building Standards

(Scotland) (Consolidated) Regulations issued by the Scottish

Development Department.

o It is dangerous to alter the specifications or to modify this

product. Do not tamper with it or attempt to modify the

appliance in any way.

o When installing the hood, ensure that the following

recommended distances are observed between the highest point

on the hob top (including the burners) and the bottom of the

cooker hood:

 Electric cookers: 700 mm

 Gas cookers: 700 mm

 Coal/ oil cookers: 800 mm

IMPORTANT: DO NOT

SET YOUR COOKER HOOD LESS

THAN 700mm ABOVE YOUR COOKER.

o When installed between adjoining wall cabinets, the cabinets

must not overhang the hob.

5

o The edges of the cooker hood are sharp – be mindful of this as

you handle your appliance, especially during installation and

cleaning. DO NOT CLEAN IN BEHIND THE GREASE FILTERS!

o If the room where the cooker hood is to be used contains a fuel

burning appliance such as a central heating boiler then its flue

must be of the sealed or balanced flue type.

o If other types of flue or appliances are fitted, ensure that there is

an adequate supply of air in the room.

o When the hood is being used in its extractor function, ensure

that the ducting is fire retardant and that there are no bends

sharper than 90 degrees as this will reduce the efficiency of the

hood.

o Ensure the ducting for the extractor function has the same

diameter as the outlet hole all the way through.

o Keep young children from using, playing with or

tampering with the cooker hood. Older children

and infirm persons should be supervised if they are

using the cooker hood.

o Your cooker hood is for domestic use only.

o Please dispose of the packing material carefully – children are

especially vulnerable to it.

o Dirty oil is an even greater fire risk.

o Always put lids on pots and pans when cooking

on a gas cooker.

o The manufacturer refuses to accept any responsibility for

damages arising to the hood or it catching on fire, from a failure

to observe the fire safety advice contained in this instruction

booklet.

6

o Remember that when in extraction mode, your cooker hood is

removing air from your room. Ensure that proper ventilation

measures are being observed.

o Note: Your cooker hood is designed to remove cooking

odours from the room and not steam.

o Warning - Always ensure that the cooker

hood has been disconnected from the

power supply before carrying out any work

on the hood, including replacing light bulbs.

o Do not connect the ducting system of this appliance to any

existing ventilation system which is being used for any other

purpose.

o Do not install above a cooker with a high level grill.

7

o Never leave frying pans unattended during use

as overheated fats and oils might catch fire.

o The lights on this appliance should only be used during operation

of the cooker hood. They should not be left on permanently and

used as a lighting source.

o The cooker hood should not be exposed to a direct heat source

from the cooking device underneath it, i.e. a naked flame from a

gas burner or heat from electric hob zones without a pan on

them.

o Do not attempt to use the cooker hood if it is damaged in any

way. Never attempt to use it without the grease filters fitted or

if the filters are excessively greasy!

o Never flambé cook under this cooker hood.

THE MANUFACTURER DECLINES ALL

RESPONSIBILITY IN THE EVENT OF FAILURE TO

OBSERVE THE INSTRUCTIONS GIVEN HERE, FOR

INSTALLATION, MAINTENANCE AND SUITABLE

USE OF THE HOOD.

Specifications of your cooker hood

PRODUCT DIMENSIONS

Height: 650 mm

Width: 900 mm

Depth: 430 mm

Your cooker hood is fitted with:

o Touch control operation

o LCD display

o Integrated centrifugal motor

o Cut off timer

o 3 Speeds

o 2 x Washable aluminium grease filters

o 2 x LED lights

o Extraction capacity: 1000 m³/hr

o Optional extras: 1 x pair S1 Carbon filters required for

recirculation.

CQ4SS Decorative chimney cover

* If you are using the appliance in recirculation mode, then PLEASE

NOTE that some of the vent in the upper chimney section must be

exposed. You will have to take this into account when calculating the

minimum height of the cooker hood when installed.

8

Using your cooker hood

o Make sure that it has been installed by a suitably qualified

person, as per the information contained in Baumatic’s

installation instructions.

o When you initially connect the cooker hood to the electricity

supply, the backlight will turn on and the hood will enter stand-

by mode. If no buttons are pressed the backlight will turn off

again after 30 seconds.

Setting the time of day

o Press the timer button for about 5 seconds to enter the time

setting mode. The hour digits will begin flashing.

o Use the speed selection button to increase the number of hours

and the lamp button to decrease the number of hours shown.

o Press the timer button again to confirm the hour setting. The

minute digits will being flashing.

o Again, use the speed selection button to increase the number of

minutes and the lamp button to decrease the number of minutes

shown.

o Press the timer button once again to confirm the minute setting.

The time of day will then be set and the hood will automatically

exit the time setting mode.

o If you wish to change the time of day in the future, press and

hold the timer button for about 5 seconds to enter the time

setting mode and follow the above procedure.

Light control

o Press the lamp button once to turn the hood lights on. If you

press this button again they will turn back off.

9

o It is highly recommended that the hood lights are only used

when the appliance is in operation. They should not be used as a

permanent lighting source for your kitchen.

Speed selection

o To switch the cooker hood motor on you should press the speed

selection button. The motor has 3 speeds which are LOW,

MEDIUM and HIGH.

o One press of the speed selection button will cause the motor to

run at LOW speed.

o Two presses of the speed selection button will cause the motor

to run at MEDIUM speed.

o Three presses of the speed selection button will cause the motor

to run at HIGH speed.

o Another press of the speed selection button will return the motor

to LOW speed.

o To switch the hood off after use, press the power button. When

you next turn the hood on using the power button, the motor will

start to work at the speed it was set on last time.

IMPORTANT: IDEALLY YOU SHOULD TURN ON YOUR

HOOD TEN MINUTES BEFORE YOU START TO COOK,

OR AT THE VERY LEAST WHEN YOU BEGIN COOKING.

YOU SHOULD ALSO RUN YOUR HOOD FOR TEN

MINUTES AFTER YOU HAVE FINISHED COOKING.

The cut-off timer

o You can program your cooker hood to switch off automatically

after a set time.

o To set a cut-off time, switch the hood on and select a speed.

Then press the timer button to enter the countdown setting

mode.

o You can then use the speed selection button to set the required

countdown time when you wish for your hood to switch off.

When you first press the speed selection button, the display will

show the minimum cut-off time of 5 minutes. Each press of the

speed selection button after this will increase the cut-off time by

1 minute.

o The maximum countdown time that you can set is 60 minutes.

10

o When the display shows the correct countdown time, release all

buttons and in a few seconds the countdown will begin.

o When the countdown time reaches “00:00” the cooker hood will

switch off automatically.

Cleaning your Baumatic cooker hood

IMPORTANT: BEFORE CLEANING, ALWAYS

ENSURE THAT YOU HAVE SWITCHED YOUR

COOKER HOOD OFF AT THE OMNI-POLAR

SWITCH, SET AT THE WALL FROM THE CABLE.

Cleaning

o Clean the external parts of your cooker hood with mild liquid

detergent and a new damp cloth.

o Never use abrasive powder, corrosive solvents or brushes.

o Never insert pointed objects into the motor’s protective grid.

o Only clean the control panel and grease filter grill with mild liquid

detergents and a new damp cloth.

o If you are using the appliance in recirculation mode, then be

sure to replace the carbon filter at the recommended interval

(see section on “Fitting the carbon filter”). A build up of grease

could cause a fire hazard.

o Never attempt to clean the area above the grease filter(s).

The grease filters

o Your cooker hood includes grease filters which help to absorb

grease particles to protect your kitchen and furniture from

greasy residues.

o These metallic filters may become inflammable if they become

saturated with this greasy residue.

o To prevent this fire hazard, the filters should be cleaned

regularly. Depending on use, this should be done every 10-15

days or at least once a month, using hot water and normal

washing-up detergent.

o DO NOT WASH THE GREASE FILTERS IN A DISHWASHER.

11

Maintenance

Removing and cleaning the grease filters

12

o First lift up the cover screen and

then remove the grease filters by

pulling down on the handle and

pulling them away from the cooker

hood as shown in the diagram

above.

o Soak the grease filters in hot water and washing up liquid for at

least 3 minutes. Then use a soft brush to loosen any grease

deposits that have formed.

o Rinse the grease filters off thoroughly with hot

water.

o Repeat the process if required.

o Refit the grease filters once they have dried

and close the cover screen.

IMPORTANT: Let the grease filters dry thoroughly before

refitting them in the cooker hood.

Changing a light bulb

IMPORTANT: BEFORE ATTEMPTING TO CHANGE

A LIGHT BULB, YOU MUST ENSURE THAT YOU

HAVE DISCONNECTED THE COOKER HOOD FROM

YOUR MAINS SUPPLY.

13

o Prior to touching the light bulbs ensure they are cooled down.

Using a flat-headed screwdriver, gently prise the edge of the light

unit out of the fixture, as shown in the picture below. Please note

that it may be easier to use two screwdrivers.

o Once the light unit has been released from the fixture, gently

pull out the light unit.

o There are wires connected to the back of the light unit. Once you

have pulled out the light unit and wires a short distance, you can

disconnect the wires by pulling them out of the connectors.

IMPORTANT: It is not possible to replace the bulbs individually.

It will be necessary to obtain the bulbs, bulb holders and wiring as a

complete part. This is available from our Spares Department.

o Fit the replacement light unit and wiring in the reverse order,

first by attaching the wires to the connectors, and then by

inserting the light unit into the light fixture.

o Ensure that the light unit securely locks into place.

IMPORTANT: If the light unit still does not work after installing the new

unit then please ensure that the wires have been properly connected

and the hood has been reconnected to the power supply before

contacting the Customer Service Department.

Fitting the carbon filters

If the appliance is being used to be used in recirculation mode then it

is necessary to fit carbon filters. This will help to absorb unpleasant

odours caused by cooking.

IMPORTANT: BEFORE ATTEMPTING TO FIT OR

REMOVE THE CARBON FILTERS, YOU MUST

ENSURE THAT YOU HAVE DISCONNECTED THE

COOKER HOOD FROM YOUR MAINS SUPPLY.

1) Remove the grease filters (as described

previously).

2) Hook the carbon filter over

the pins that are located at the

end of the motor.

14

3) Turn the carbon filter clockwise, until

you feel it click into place.

o Repeat this process for the

second carbon filter. You need to

place a carbon filter at either end

of the motor.

o Refit the grease filters.

o The carbon filters should be replaced every 3 - 6 months or if

they show signs of damage.

Installation

IMPORTANT: Before installation and usage read

all the instructions and make sure that the

voltage (V) and the frequency (Hz) indicated on

the rating plate are exactly the same as the

voltage and frequency in your home. The rating

plate can be found behind the grease filters.

The manufacturer declines all responsibility in the event of the installer

failing to observe all the accident prevention regulations in force,

which are necessary for normal use and the regular operation of the

electric system.

15

Electrical connection

16

YOUR COOKER HOOD IS INTENDED FOR FITTED AND

PERMANENT INSTALLATION.

o The cooker hood’s power cable must be fitted upstream from the

electrical connection, using an omni-polar switch with a contact

distance of at least 3 mm. THE FUSE MUST BE RATED AT 3

AMPS.

WARNING: THIS APPLIANCE MUST BE EARTHED. It

should only be connected by a competent person, using

fixed wiring via a double pole switched fused spur outlet.

(UK ONLY).

We recommend that the appliance is connected by a qualified

electrician, who is a member of the N.I.C.E.I.C. and who will comply

with the I.E.E. and local regulations. The wires in the mains lead are

coloured in accordance with the following UK code:

Blue = Neutral, Brown = Live, Green/Yellow = Ground

If you only find two wires in the main’s lead (blue and brown),

then neither must be connected to the earth terminal.

o As the colours of the wires in the appliance’s mains lead may not

correspond with the coloured markings identifying the terminals

in your spur box, please proceed as follows:

o The blue wire must be connected to the

terminal marked “N” (neutral), or coloured

black.

o The brown wire must be connected to the

terminal marked “L” (live), or coloured red.

Before beginning installation

o Check that the product purchased is of a suitable size for the

chosen installation area. In addition check whether there is an

electrical socket available that will be accessible once the hood is

mounted. If the product is going to be used in extraction mode,

then there should also be space to connect a ducting hose to the

outside.

o Carry out all necessary masonry work prior to the fitting of the

cooker hood.

17

o Ensure that all electrical connections are carried out by a suitably

qualified person.

o Before commencing installation of the cooker hood the grease

filter should be removed.

o Check inside the product and insure that there is no transit

packaging or any other materials, such as packets of screws,

guarantees etc. These should be removed and kept for future

use.

o If possible, disconnect and move freestanding or slot-in cookers

from their position, to provide easier access to the rear wall and

ceiling. If this is not possible, then a thick, protective covering

should be placed over the worktop, hob top or cooker. This will

help to protect these surfaces from damage and debris.

o Select a flat surface for assembling the cooker hood. Cover that

surface with a protective covering and place all cooker hood

parts and fittings on it.

o In addition check whether there is an electrical socket available,

which will be accessible after the hood is mounted. If you are

going to use the appliance in extractor mode, you should also

ensure that there is space to connect a fumes discharge device

to the outside.

o Rawl plugs are provided to secure the hood to most types of

walls and ceilings. However a qualified technician must verify the

suitability of the materials, in accordance with the type of wall

and ceiling. The wall and ceiling must be strong enough to take

the weight of the hood.

o Do not tile, grout or silicone this appliance to the wall. This

appliance is designed to be surface mounted only.

Extraction mode or recirculation mode?

IMPORTANT: YOU WILL HAVE TO DECIDE BEFORE

INSTALLING YOUR COOKER HOOD WHETHER TO USE

IT IN EXTRACTION MODE OR RECIRCULATION

MODE.

What is the difference between extraction and recirculation

modes?

In extraction mode, the stale air will be taken out of the room via

external ducting.

In recirculation mode stale air is taken via the grease filter(s), and

passed through a charcoal filter for purification. The air then re-enters

the kitchen via an opening in the hood.

For optimum performance, we recommend that the cooker hood is

used in extraction mode and connected to external ducting.

Unfortunately if you live in a flat or the hood is too far from an outside

wall, this may not be possible. The only alternative is to recirculate the

air.

Do I need a charcoal filter?

All cooker hoods have a grease filters but if you are using your cooker

hood in recirculation mode, then a charcoal filter must be fitted in

addition to the grease filters.

Installing your cooker hood

o We recommend that at least two people install

this hood.

o Please note that the styles of cooker hood shown in the

line drawings in the following pages are sometimes

different to the shape of the BES900BGL. However the

installation method shown is correct and MUST be

followed.

18

IMPORTANT: YOUR COOKER HOOD SHOULD BE CONNECTED TO

YOUR MAINS SUPPLY AFTER THE REST OF THE INSTALLATION

PROCESS HAS BEEN COMPLETED.

19

1) Remove the grease filters (as

previously described).

2) Position the hood against the wall that you are intending to install it

on and mark the position of the screw holes that are to be drilled (as

shown in the figure above).

2a) The support screw holes are indicated by figure A in this drawing

and the anchoring screw holes are indicated by figure B.

3) Using a drill bit with an 8 mm

diameter, make holes in the wall on the

positions that you have marked in step

2.

4) Insert rawl plugs into all of the holes that you have drilled.

5) Fasten the support screws halfway in, leaving them 10 mm out of

the wall.

20

Page is loading ...

Baumatic BES900BGL - 36900540 User manual

This manual is also suitable for

Baumatic BES900BGL - 36900540 User manual

Related papers

Other documents