1
EC800 Series Installation Guide
•
1 EC800 system unit
•
1 Power adapter: 60W
•
6 mounting screws for Mini PCIe module
•
1 Quick Installation Guide
•
1 CD disk includes:
- Drivers / Manual
Package Contents
Mic-in
LAN 2
USB
Power
Reset
HDD LED
LAN 1
COM 1
CFast Status LED
Wi-Fi/3G
Antenna
Wi-Fi/3G
Antenna
DVI-I9~24V DC-in COM 2/
Isolated 4-bit DIO
Line-out
Wi-Fi/3G
Antenna
Wi-Fi/3G
Antenna
VGA9~24V DC-in COM 2
Line-out
micro HDMI
Panel
Dual Display Rear View
Front View
Single Display Rear View
DFI reserves the right to change the specifi cations at any time prior to the product's release. For the latest revision and for a
more details of the installation process, please refer to the user's manual on the website.
www.dfi .com
2
1. Make sure the system and all other peripheral devices connected to it has been powered-
off.
2. Disconnect all power cords and cables.
Removing the Chassis Cover
Mounting Screw
4. After removing the mounting screws, lift the
cover up.
5. The CFast socket, and Mini PCIe/mSATA slot are readily accessible after removing the chassis
cover. And the SIM slot is also accessible at the side of the system board.
mSATA
CFast Socket
Lift the Cover Upward
PCIe x1, USB,
3G signal
PCIe x1, USB,
Wi-Fi signal
SIM slot
3. The 4 mounting screws on the bottom side
(labeled side) of the system are used to
secure the cover to the chassis. Remove
these screws and then put them in a safe
place for later use.
3
Installing a Mini PCIe and/or mSATA Card
1. Locate the Mini PCIe slot on the system
board.
2. The system board is equipped with 2 Mini
PCIe slots. The Mini PCIe slot supports full
length and half length Mini PCIe card. Note
the key on the slot. The key ensures the
Mini PCIe card can be plugged into the slot
in only one direction.
Half length
Full length
PCIe x1, USB,
3G signal
PCIe x1, USB,
Wi-Fi signal
3. Grasping the Mini PCIe card by its
edges, align the card into the slot at an
approximately 30 degrees angle. Apply
fi rm even pressure to each end of the card
until it slips down into the slot. The contact
fi ngers on the edge of the card will almost
completely disappear inside the slot.
PCIe x1, USB, and 3G
signals
4. Push the Mini PCIe card down and use the
provided mounting screws to secure the
card on the system board.
Mounting Screw
PCIe x1, USB, and
Wi-Fi signals
4
Board Layout and Jumper Settings
DDR3
1
1
Intel Atom
D2550/ N2800/
N2600
Intel
NM10
Fintek
F81866
VGA
Buzzer
Standby_LED
3
1
LAN 1
LAN 2
USB 1
USB 3
System fan
Battery
DDR3 DDR3 DDR3
10
13
3
10
1
VGA
/
DVI-I
HDD_LED
DVI-I/VGA
COM 1
21
20
DIO
USB 4-5
10
12
USB 0
USB 2
Line-out
COM 2/ DIO Select (JP10)
12
COM 2/ DIO Select (JP9)
USB 0-3/ 4-5
Power Select (JP8)
5
6
1
2
12
Intel
WG82574L
Intel
WG82574L
19
SIM Card slot
Mic-in
Reset
Power
DC-IN
1
DDR3 DDR3
Mini PCIe 2
Realtek
ALC886
DDR3
DDR3
ICS
9VRS4339
Asmedia
ASM1442
Intersil
ISL95831
Mini PCIe 1 mSATA
SPI Flash BIOS
CFast
Power-on/ CMOS
Select (JP5)
2
56
1
Chassis Intrusion
COM 2/
Isolated 4-bit DIO
HDMI
TOP BOTTOM
Power-on/ Clear CMOS Select JP5
Power-on via power button (default) 1-3 On
Auto power-on 3-5 On
Normal (default) 2-4 On
Clear CMOS 4-6 On
COM2/ DIO Select JP9 and JP10
COM2 (default) 1-4-7-10 On
2-5-8-11 On
DIO 2-5-8-11 On
3-6-9-12 On
USB Power Select (JP8) USB 0-1 USB 2-5
+5V 2-4 On 1-3 On
+5V_standby (default) 4-6 On 3-5 On
Note:
You cannot use COM2 and DIO at the same time. Please set up JP9 and JP10 at the same time.
934-EC8000-0B0G
A26054441
Note:
The CD that came with the system contains an autorun screen to install drivers, utilities,
and software applications required to enhance the performance of the system and a user's
manual for your reference. Insert the CD into a CD-ROM drive. The autorun screen will
appear. If after inserting the CD, “Autorun” did not automatically start, please go directly to
the root directory of the CD and double-click “Setup”. Please install all required drivers.
/
