Troy-Bilt 41AS99BS766 Owner's manual

Brand: Troy-Bilt

Model: 41AS99BS766

Type: Owner's manual

Troy-Bilt 41AS99BS766 is a versatile gas-powered leaf blower that can help you tackle a range of outdoor cleaning tasks. With its powerful 40:1 2-cycle engine, it generates impressive airflow for effective debris removal. It features a variable speed control, allowing you to adjust the airflow based on the task at hand. The unit comes with both a general use tube and a special use tube for concentrated airflow when needed. The special use tube is ideal for stubborn debris or hard-to-reach areas.

IMPORTANT: READ THE OPERATOR’S MANUAL THOROUGHLY AND FOLLOW

THE SAFE OPERATION PRACTICES WHILE OPERATING THE UNIT

778-13418 / 00

Lea la traducción en Español en el manual.

Unpacking the Unit

Set the unit on a flat, level

surface. Align the slot on the

upper blower tube with the tab

on the blower outlet. Push the

upper blower tube onto the

blower outlet until the tab locks

securely into the slot.

NOTE: Always install the upper

blower tube.

Assembling the Unit

1 2

Remove all contents from the

carton.

Align the tab on the general use tube

or special use tube with the hole on

the upper blower tube. Push the

general use tube or special use tube

into the upper blower tube until the

tab locks securely into the hole.

NOTE: Only use the special use tube

to concentrate and intensify the

air flow when needed. DO NOT

use the special use tube for

general work or for long periods.

NO ASSEMBLY TOOLS REQUIRED

Fuel Cap

Special Use Tube

Upper Blower Tube

General Use Tube

Mix thoroughly in a separate

fuel can:

– 3.2 fl. oz. of 2-cycle engine

oil

– 1 gallon of fresh unleaded

gasoline (less than 30 days

old)

NOTE: Do not mix directly in

the unit fuel tank.

Place the unit on a level

surface. Remove the fuel cap.

Fill the fuel tank. Replace the

fuel cap. Move the unit at least

30 ft. (9.1 m) from the fuel

container and the fueling site

before starting the engine.

5 6

40:1

Starting the UnitAssembling the Unit

Blower

Outlet

Starting the Unit

DO NOT squeeze the throttle

control. Crouch in the starting

position.

DO NOT squeeze the throttle

control. Pull the starter rope

with a controlled and steady

motion until the unit starts.

Idle the engine for 5 to 10

seconds. If the unit stops

during this time, squeeze and

hold the throttle control or

move the cruise control to the

FAST position, then pull the

starter rope in a controlled

and steady motion until the

unit starts.

Once the engine is properly

warmed, the cruise control

may be adjusted and the

throttle control can be used

normally.

12 14

Squeeze and hold the

throttle control or move the

cruise control to the

FAST position. Allow the

engine to warm up for 30 to

60 seconds.

DO NOT squeeze the throttle

control.

FAST

Move the cruise control to the

SLOW position.

DO NOT squeeze the throttle

control. Flip the choke lever

clockwise until it clicks into the

START position.

SLOW

Press the primer bulb 10 times,

or until fuel is visible.

Primer

Bulb

10 X

Primer Bulb

Throttle Control

Starter Rope

Grip

Choke Lever

Cruise Control

DIDN’T START?

Repeat the starting instructions.

If the unit still fails to start,

refer to the operator’s manual

for additional starting and

troubleshooting information.

Need Help?

Call 1-800-828-5500

Tab

Slot

Hole

Tab

Troy-Bilt 41AS99BS766 Owner's manual

Troy-Bilt 41AS99BS766 Owner's manual

Troy-Bilt 41AS99BS766 Owner's manual

Related papers

Other documents