Schacht Loom Bench Bags User manual

Brand: Schacht

Model: Loom Bench Bags

Type: User manual

This manual is also suitable for

Loom Bench Shown with Optional Bench Bags

Loom Bench

Assembly InstructIons

Find out more at schachtspindle.com

Schacht Spindle Company 6101 Ben Place Boulder, CO 80301

p. 303.442.3212 f. 303.447.9273

– 2 – – 3 –

Loom Bench

Assembly InstructIons

Hardware

4 – 3-1/4" x 1/4" carriage bolts

8 – 1/4" at washers

4 – 1/4" lock washers

4 – 1/4" hex nuts

4 – 2" x 1/4" truss head machine

screws

8 – 1/4" barrel nuts

2 – 5/16" x 6-1/2" hex bolts

2 – 5/16" hex nuts

10 – 1-3/4" phillips at head tapping

screws (there are two extra screws)

4 – 3-1/2" x 1/4" truss head machine

screws

required Tools

1/2" wrench

7/16" wrench

Phillips screwdriver

Flat screwdriver

Hammer or mallet

seat height

adjuster

seat support

slanted

position

at

position

uprights

middle supports

base

bench seat

– 2 – – 3 –

assembly

1. Before assembling the bench,

decide whether you want your bench

seat in a slanted or at position. For

a slanted seat position, assemble the

bench seat supports to the seat height

adjusters with the slanted part on

top. For a at seat position, follow the

same instructions, but with the at

position on top.

2. Attach each seat support to the

outside of each seat height adjuster

with two 3-1/4" carriage bolts. Insert

the bolts from the outside to the

inside and tap the head of the carriage

bolt into the wood with a hammer.

Place a at washer, lock washer and

1/4" hex nut on each bolt and tighten.

3. Assemble each base to an upright

using two 3-1/2" truss head machine

screws and two barrel nuts. Make

sure the grooves in the uprights

face the inside of the bench and the

grooves meet to form a “V”.

4. Assemble the middle supports to

the uprights by placing them in the

grooves and securing them with the

2" truss head machine screws and

barrel nuts.

5. Fit the seat height adjusters

between the uprights. For a bench

20" high, line up the holes in the top

of the uprights with the top holes in

the seat height adjusters. Slip a 5/6"

x 6-1/2" hex bolt with a at washer

through the holes. Put another at

washer on the end and thread on

a 5/16" hex nut. Arrange the seat

height adjuster so that it is vertical

and tighten the hex bolts.

6. Place the bench seats on top of

the bench seat supports. Be sure that

the countersunk holes are facing up,

and the rounded corners are on the

outside. Line up the holes in the seat

with the pre-drilled guide holes in

the bench seat supports. If needed,

readjust the seat height adjusters so

the holes in the bench seat and the

holes in the bench seat supports line

up. Screw the bench seat down with 8

of the 1 3/4" at head screws.

7. Your bench is now assembled with

a height of 20". Test this height with

your loom. If you want the bench to

be higher, pull out the hex bolts from

the top of the uprights, raise the seat

to the height you want and slip the

hex bolts back through the holes and

tighten them. The maximum bench

height is 24". •

at

position

– 4 – – PB –

Bench Bag

Assembly InstructIons

metal rod

cloth bag

wood bench bag end

wood bench

1. Rub a little bar soap along 1" of

each end of the steel rods.

2. Gently tap the steel rods into the

holes in the ends of your Schacht

bench seat. Place a scrap of wood be-

tween the hammer and the steel rods

to protect the ends of the rods.

ParTs

2 – steel rods

1 – wood bench bag end

1 – cloth bag

Tools

Hammer or mallet

Scrap wood

3. Slip the bench bag onto the rods.

4. Line up the holes in the wood

bench bag end with the steel rods.

Use the scrap wood as protection

between your hammer and the wood

bench bag end.

Schacht Loom Bench Bags User manual

Brand: Schacht

Model: Loom Bench Bags

Type: User manual

This manual is also suitable for

Download PDF

report

Schacht Loom Bench Bags User manual

This manual is also suitable for

Schacht Loom Bench Bags User manual

Related papers

Other documents