INSTALLATION INSTRUCTIONS
INSTRUCTION SHEET NO. 17-5122C (9/2014)
PDV/PVR ARRESTERS
PDV/ PVR 避雷器
CAUTION
The equipment covered by these instructions should be installed and serviced only by competent personnel familiar
with good safety practices. This instruction is written for such personnel and is not intended as a substitute for
adequate training and experience in safe procedures.
WARNING
Prior to installing this product, check the nameplate information to verify that it is the correct product for the application.
Verify that the nameplate information corresponds to the information provided on the outline drawing.
The drawing below shows the typical information contained
on the nameplate (ANSI at left, IEC center). The nameplate
information is found on the top metal plate of the arrester.
The detailed view below (at right) shows the recommended
arrangement for fasteners attaching the NEMA crossarm
bracket and transformer mounting bracket (if used) to the
insulating base bracket of the arrester.
The recommended tightening torques for PDV/PVR
arrester fasteners are as follows:
3/8 inch 20 ft-lb (27 N-m)
1/2 inch or M12 40 ft-lb (54 N-m)
Model
type
Catalog
number
Arrester
class
Country of
origin
1/2 Hex nut
1/2 Lock washer*
Arrester
mounting
bracket
Short
circuit
rating
MCOV
Duty cycle
voltage rating
Country of
origin
COV
Rated voltage
Insulating
base
1/2 Round
head square
neck bolt
Date code
* The use of any other washer may result in
damage and is not recommended.
HUBBELL Power Systems • The Ohio Brass Company
1850 Richland Avenue, East Aiken, SC 29801
These instructions do not purport to cover all details or variations in equipment nor to provide
for every possible contingency to be met in connection with installation, operation or
maintenance. Should further information be desired or should particular problems arise which
are not covered sufficiently for the purchaser’s purposes, the matter should be referred to
Hubbell Power Systems.
©Copyright 2014 Hubbell Incorporated
安 装 作 业 指 导 书
作业指导书编号： 17-5122C (9/2014)
PDV/PVR 型 避 雷 器
注 意
本指南所涵盖的产品安装及维护作业应由熟知安全作业规程的专业人员完成. 本指南仅针对该类专业
人员编写，不得代替此类设备作业时所必须的有关安全作业规范的培训及经验.
警 告
在产品安装前请仔细核对铭牌信息以确认其符合实际要求，确认铭牌信息与产品外形图标识的信息一致.
下图所示为产品铭牌所包含的标准信息（左图为 ANSI
标准 ，中图为 IEC 标准).
铭牌信息请查看避雷器顶部金属铭牌.
推荐使用如下方右图所示方式连接避雷器底部绝缘支架与
NEMA横担及变压器安装支架（如使用的话）.
推荐采用如下所示力矩紧固PDV/PVR型避雷器产品：:
3/8” 27 N-m（20 ft-lb）
1/2” 或 M12 54 N-m (40 ft-lb)
产品
型号
产品
编号
避雷器
等级
产地
1/2”六角螺母
1/2’锁紧垫片*
避雷器安
装支架
额定短
路电流
最大
持续工作电压
额定电压
产地
持续工作电压
额定电压
绝缘底座
1/2”
圆头方颈螺栓
生产日期
*
如使用其他任何垫片可能导致事故，故不推荐.
HUBBELL Power Systems • The Ohio Brass Company
1850 Richland Avenue, East Aiken, SC 29801
该指南未涵盖设备的所有细节或工程变更，不包含涉及安装、运行或维护时可能出现的任何突
发状况
.
本指南仅针对最终用户的使用而编写，如需了解更多产品信息或遇到本指南中未提及
的特定问题，请咨询合保电气
.
©Copyright 2014 Hubbell Incorporated
-
1
-
2
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Hubbell 17-5122 Installation guide
-
-
-
-
-
-
-
-
-