Ohlins FGK227 Mounting Instruction

Category
Motorcycle Accessories
Type
Mounting Instruction
Front Fork Kit for Kawasaki ZX-6R 636
FGK 227
Mounting Instructions
Note!
Please note that this image is a general representation
of the product and may differ slightly from your product.
Note!
Please note that during storage and transportation,
especially at high ambient temperature, some of the oil
and grease used for assembling may leak and stain the
packaging. This is in no way detrimental to the product,
wipe off the excessive oil/grease with a cloth.
Note!
Before installing this product, check the contents
of the kit. If anything is missing, please contact an
Öhlins dealer.
Warning!
This kit should only be installed by an authorized Öhlins
dealer. The installation procedure requires certain tools.
Warning!
Before installing this product, read the Öhlins Owner’s
Manual. The shock absorber/front fork/steering damper
is an important part of your vehicle and will affect
the stability.
Kit Contents
Description Part No Pcs
Front fork kit FGK227 1
Sticker set Öhlins 1
Owner’s manual 07284-01 1
2/8
MOUNTING INSTRUCTIONS
Note!
The front fork is a very important part of the vehicle and
will therefore affect the stability.
Note!
Read and make sure that you understand the
information in this manual before you use this product.
If you have any questions regarding installation or
maintenance please contact your nearest Öhlins dealer.
Note!
Öhlins Racing AB can not be held responsible for any
damage to the front fork, vehicle, other property or
injury to persons, if the instructions for installing and
maintenance are not followed exactly.
Warning!
This product was developed and designed exclusively
for a specic vehicle model and should only be installed
on the intended vehicle model in its original condition as
delivered from the vehicle manufacturer.
After installing this product, take a test ride at low
speed to make sure that your vehicle has maintained its
stability.
Note!
When working on this product, always consult your
Vehicle Service Manual.
Note!
This Manual should be considered as a part of the
product and should therefore accompany the product
throughout its life cycle.
© Öhlins Racing AB. All rights reserved. Any reprinting
or unauthorized use without the written permission of
Öhlins Racing AB is prohibited.
Printed in Sweden.
Safety Symbols
In this manual, mounting instructions and
other technical documents, important
information concerning safety is distin
-
guished by the following symbols:
The Safety Alert Symbol means: Warning! Your
safety is involved.
Warning!
The Warning Symbol means: Failure to follow
warning instructions can result in severe or fatal
injury to anyone working with, inspecting or using
the front fork, or to bystanders.
Caution!
The Caution Symbol means: Special precautions
must be taken to avoid damage to the front fork.
Note!
The Note Symbol indicates information that is
important regarding procedures.
TOOLS
Tool 00797-08Tool 01765-03 Tool 01797-07 Tool 00786-08 (Ø41)
3/8
1 - REMOVE ORIGINAL FRONT FORK
Warning!
It is advisable to have an Öhlins dealer install the shock
absorber/front fork/steering damper.
Warning!
If working on a raised vehicle, ensure it is securely
supported so that it will not tip.
Note!
Before mounting this product clean the vehicle
thoroughly.
Note!
When working on this product, always see the Vehicle
Service Manual for vehicle specic procedures and
important data.
1.1
Put the motorcycle on a workstand so that the
front wheel barely touches the ground.
1.2
Remove the front fender, the brake calipers
and the front wheel.
1.3
Release the spring preload.
1.4
Loosen the upper triple clamp by loosening
the screws.
1.5
Loosen (do not remove) the top cap ½ turn.
1.6
Loosen the lower triple clamp by loosening the
screws.
1.7
Remove the front fork legs from the triple
clamps.
Screw
1/2 turn
1
4
3
5
2
4/8
2.1
Loosen the top cap from the outer tube.
2.2
Pull down the outer tube.
2.3
Remove the top cap by loosening it from the
shaft. Use appropriate tool according to your
vehicle service manual.
2.4
Loosen the seal head from the steel tube to
remove the cartridge. Use appropriate tool
according to your vehicle service manu
-
al.
Caution!
Make sure that the lose parts will not fall out when
draining the fork leg.
2.5
Drain the fork leg from oil. Remove the spring
and surrounding parts from the fork leg.
2.6
Loosen the steel tube lock screw at the fork
bottom.
Caution!
If the lock screw is not removed the steel tube will be
damaged.
Note!
Use a heat gun to soften the Loctite between the lock
screw and the fork bottom.
2.7
Push the outer tube as far up as possible. Use
tool 00786-05, install it close to the outer tube.
Loosen the steel tube from the fork bottom.
Note!
Use a heat gun to soften the Loctite between the steel
tube and the fork bottom.
Note!
Do not remove tool 00786-05 from the steel tube. You
will need it to reinstall the steel tube.
1 3
4
5
6
5
7
2 - DISASSEMBLE ORIGINAL FORK
5/8
2 - DISASSEMBLE ORIGINAL FORK
Caution!
Work with only one fork leg at a time. Do not mix the parts.
Caution!
The front fork kit is divided into one compression
cartridge and one rebound cartridge.
Important:
► Install the cartridge marked Reb (Rebound)
in the right side fork leg.
► Install the cartridge marked Comp
(Compression) in the left side fork leg.
3.1
Remove the top cap.
3.2
Remove the spring support and the preload tube.
3.3
Remove the cylinder tube from the cartridge.
Caution!
Be careful not to damage the piston ring.
3.4
Loosen the steel adaptor from the cylinder
tube’s adaptor.
3.5
Install the steel adaptor.
Note!
Make sure to install the adaptor correctly. See gure.
Note!
The original steel washer (Removed in step 2.8) shall
not be reinstalled.
2.8
Remove the o-ring and the steel washer from
the fork bottom.
Note!
The steel washer will not be used for the Öhlins kit and
shall therefore not be reinstalled.
3 - INSTALL ÖHLINS FRONT FORK KIT
8
Spring
support
Preload
tube
1
2
3
Adaptor
4
5
6
6/8
3 - INSTALL ÖHLINS FRONT FORK KIT
3.6
Apply red grease on the original o-ring and
install it into the fork bottom.
3.7
Reinstall the steel tube.
Loctite 2701.
Tightening torque 130 Nm.
3.8
Reinstall the steel tube lock screw.
Loctite 2701.
Tightening torque 3 Nm.
3.9
Put the cylinder tube carefully into the fork leg.
Use an extended 17 mm allen key to tight
-
en the cylinder tube’s adaptor to the steel
adaptor.
Loctite 243 (on the adaptor thread)
Tightening torque 40 Nm.
Caution!
Be careful not to damage the inside of the cylinder tube
when tightening with the extended allen key.
3.10
Pour 0,5 litre Öhlins Front Fork fuid into the
fork leg.
3.11
Put the cartridge carefully in the fork
leg. Tighten to the cylinder tube with tool
01797-07. Apply red grease on the seal head
thread. Tightening torque 20 Nm.
Caution!
Make sure that the piston ring is in its correct position
and be careful not to damage it.
3.12
Open the compression and the rebound
adjuster fully. Install the top cap directly to the
shaft extension (No spring or preload tube).
Pull up the outer tube and tighten it to the top
cap. Handtighten only.
10
7
8
11
9
17 mm allen
key
7/8
3.13
Pump out all air from the cartridge by pulling
the outer tube up and down 10-15 times.
3.14
Remove the top cap from the fork leg.
3.15
Make sure the shaft assembly is in the bottom
of the fork leg and that the outer tube is in its
bottom position. Measure the oil level with a
ruler. See set-up data and oil level-force dia
-
gram in this folder.
3.16
Fasten tool 01765-03 on the top of the shaft
extensioner, install preload tube,spring and
upper spring support by leading them over the
tool. See the Owner’s Manual for available
springs.
3.17
Pull up the shaft assembly and grab the spring
support with a 19 mm wrench.
3.18
Make sure that the comp/rebound adjusters
are fully open before installing the top cap.
Remove the pull-up tool and install the top cap
to the shaft extensioner. Torque 15 Nm.
3.19
Pull up the outer tube. Make sure the fork
leg is in a fully extended position. Use
tool 00797-08 to tighten the top cap to the
outer tube. Tightening torque 10 Nm.
3.20
Set the spring preload, rebound and compres
-
sion adjusters according to adjustments and
set-up data in this manual.
3.21
Install the front fork legs into the triple clamps
at the position recommended in set-up data
(Fork leg position). Tightening torque:
According to your vehcle service manual.
Note!
Measure the fork leg extension from the upper triple
clamp to the top of the outer tube.
Spring
support
Spring
Preload
tube
Spring
support
16
16
17
18
19
XXX mm
13 15
Fork leg
position
3 - INSTALL ÖHLINS FRONT FORK KIT
Öhlins Racing AB
Box 722
S-194 27 Upplands Väsby, Sweden
Phone +46 8 590 025 00
fax +46 8 590 025 80
© Öhlins Racing AB. All rights
reserved. Any reprinting or
unauthorized use without the written
permission of Öhlins Racing AB
is prohibited.
Öhlins products are subject to
continuous improvement and
development, therefore, although
these instructions include the most
up-to-date information available at
the time of printing, minor updates
may occur.
To nd the latest information
contact an Öhlins distributor.
Please contact Öhlins if you have
any questions regarding the
contents in this document.
DIAGRAM - OIL LEVEL/SPRING FORCE
SET-UP DATA
Part no. MI_FGK227_1
Issued 2017-01-01
Rebound 12 clicks
Compression 12 clicks
Spring preload 5 mm
Spring rate 9.5 N/mm
Oil level 170 mm
Fork leg position stand. pos.
Öhlins front fork uid 01309-01
0
50
100
150
200
250
300
350
400
450
500
550
0102030405060708090100 110120 130
Force [N]
Stroke [mm]
Force vs Stroke
130
140
150
160
170
180
190
200
210
220
230
240
250
260
270
280
290
300
Oillevel
1 / 1

Ohlins FGK227 Mounting Instruction

Category
Motorcycle Accessories
Type
Mounting Instruction

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Ask the document