• Fitting Material: Plastic.
• Class: Class 2
• IP Rating: IP 20
• Voltage: 220V - 240V ~ 50Hz
• Dimensions: FS276: (L)310mm x (W)48mm x (D)42mm
FS277: (L)452mm x (W)48mm x (D)42mm
• Lamp Type: FS276: 40 x Integrated LED 220 - 240V
FS277: 80 x Integrated LED 220 - 240V
• Battery: FS276: 3.7V 1.5Ah sealed Lithium-ion rechargeable battery
FS277: 3.7V 2.2Ah sealed Lithium-ion rechargeable battery
• Battery Charge time: FS276: 20 - 24 hours
FS277: 20 - 24 hours
• Battery Life: FS276: Up to 6 hours (Dim) / Up to 3 hours (Bright)
FS277: Up to 6 hours (Dim) / Up to 3 hours (Bright)
• The light source of this luminaire is not replaceable. When the light source reaches its end of life the
whole luminaire should be replaced, or the light source should only be replaced by the manufacturer.
SPECIFICATIONS
CLEANING
HOW TO OPERATE
HOW TO OPERATE
• Beforecleaningalwaysensurethepowersupplyisturnedo.
• Do not immerse the luminaire in water.
• No abrasive products, solvents, detergent may be used to clean this luminaire.
• Ensure that the luminaire does not come in contact with corrosive chemicals, etc.
1. Switch to either “LOW” or “HIGH” position, plug into AC socket, the luminaire will light up
automatically upon power failure.
2. Take out the plug from AC socket switch to “LOW/HIGH”position to light up the unit
3. Switch to OFF position when not in use.
1. Connect the power cord plug into the AC power socket and rechargeable light
2. The red LED indicator will be on when the lamp is being recharged
3. It needs approximately 20hours for a full charge
4. The built-in charger may become slightly warm during recharging, however, It is a normal phenomena.
Attachments:
Iftheexternalexiblecableorcordofthisluminaireisdamaged,itshouldbeexclusivelyreplacedby
themanufacturerorhisserviceagentorasimilarqualiedpersoninordertoavoidahazard.
To ensure that you get maximum longevity and maximum use out of your luminaire, please
observe the following safety instructions.
Electrical products can cause death, injury, or damage to property. Installation of the luminaire must
becarriedoutbyaqualiedelectrician,inaccordancewithSANS10142.Oncompletionof
installation,ensurethattheCerticateofComplianceisupdated.
• Before connecting this luminaire, ensure that voltage indicated on the rating label corresponds with the
mains voltage in your home.
• Whenchangingthelamp,ensurethatthepoweristurnedo.
• This luminaire is checked in full for conformity to the quality standards and safety requirements.
• The manufacturer / supplier is not responsible for any damage of properties and persons, caused by
the incorrect use or installation of the luminaire.
• Should you be unsure of how to install this luminaire correctly, please consult a professional electrician
or your supplier for assistance.
• Ensure all items/ components, threads and screws are tightly secured.
IMPORTANT:
• Tampering with this luminaire, i.e.using silicon sealers or incorrect cabling, will invalidate
your warranty.
• When the protection glass is damaged, it should be replaced immediately. The luminaire
must not be used without the protection glass.
• Please check whether the connection of the power cord is safe and reliable before installation.
• Always ensure that the mains supply voltage is correct.
• Always replace the lamp with one of an identical rating.
• Ensure that you do not place the luminaire near any combustible materials and / or surfaces.
• Choking hazard: May contain small parts. Keep away from children.
• Donotinsertyourngersoranypartofyourbodyintotheelectricalcontactandsocketsofthisproduct
whilst it is connected to the electricity supply.
• Item may vary slightly from the picture on the carton.
• Coastalhumiditymayeectthelongevityoftheluminaire.
• Outdoor luminaires must be cleaned to prevent rust occurring.
• Use a copper grease on all screws or strings.
IMPORTANT SAFEGUARDS