• Fitting Material: Pressed Steel.
• Motor: 40W
• Voltage: 220V - 240V ~ 50Hz.
• Protection against electric shock: Class 2 Does not Require earth connection.
• IP Rating: IP 20.Protected against solid foreign objects of 12.5mm and greater
Not for outdoor user in wet conditions and areas of high humidity.
• Dimensions: F26: (H) 1270mm X (W) 435mm X (D) 600mm
• Features: 3 Speed
Rotation / Lockable
2 Hours Time
1.9m Cable and plug top
3 Blades
SPECIFICATIONS ASSEMBLY INSTRUCTIONS
F26 - attachments:
If the external exible cable or cord of this luminaire is damaged, it should be exclusively replaced
by the manufacturer or his service agent or a similar qualied person in order to avoid a hazard.To
ensure that you get maximum longevity and maximum use out of your luminaire, please observe
the following safety instructions.
Electrical products can cause death, injury, or damage to property. Installation of the luminaire
must be carried out by a qualied electrician, in accordance with SANS 10142. On completion
of installation, ensure that the Certicate of Compliance is updated.
• Before connecting this luminaire, ensure that voltage indicated on the rating label corresponds
with the mains voltage in your home.
• When changing the lamp, ensure that the power is turned off.
• This luminaire is checked in full for conformity to the quality standards and safety requirements.
• The manufacturer / supplier is not responsible for any damage of properties and persons,
caused by the incorrect use or installation of the luminaire.
• Should you be unsure of how to install this luminaire correctly, please consult a professional
electrician or your supplier for assistance.
• Ensure all items/ components, threads and screws are tightly secured.
IMPORTANT:
• Tampering with this luminaire, IE. Using silicon sealers or incorrect cabling, will invalidate your
warranty. If one is not supplied within the carton, DO NOT use a solid speed control.
• Each blade set supplied is weighted and a complete set. If installing more than one fan, DO NOT
mix or add blades as this can cause your fan to wobble.
• Please check whether the connection of the power cord is safe and reliable before installation.
• Always ensure that the mains supply voltage is correct.
• Do not use the fan outdoors, in wet conditions or areas of high humidity.
• Do not insert objects or ngers through the bars of the grill.
• This appliance is not intended for use by young children or inrm persons unless they have been
adequately supervised by a responsible person.
• Always unplug the fan when cleaning or moving from one location to another.
• Always ensure that the fan is on an even, stable surface.
• To disconnect the appliance, unplug by rst turning off the mains power then unplugging the fan.
Do not pull on the cord ,always grap the plug.
IMPORTANT SAFEGUARDS
CLEANING
• Before cleaning always ensure the power supply is turned off and that the fan has
been unplugged.
• Do not immerse the fan in water.
• No abrasive products, solvents, detergent may be used to clean this fan.
• Ensure that the fan does not come in contact with corrosive chemicals, etc.
• Remove the front grill guard, blades and rear grill guard and wipe down parts with a damp cloth
to remove any dust.
• Ensure all parts are dry before reassembling your fan.
• The motor bearings are permanently sealed and do not require additional lubrication
• Oscillation Control
Push the oscillation knob to oscillate
Pull the oscillation knob to stop
• Operating instructions
Be sure to shut off electric supply at main switch or circuit breaker before installation.
Before doing anything ensure the fan is placed on a at and stable surface when operating
to avoid overturning.
Plug the power cord into a suitable socket
Tilt the head up or down to the required position by using a locking mechanism that will hold the
head in the desired position.
The fan is switched on using the push buttons on switch housing, i.e.
0 = Off,
1 = Low Speed,
2 = Medium Speed,
3 = High speed
• Special Attention:
1. If the supply cord is damaged, it must be replaced by the manufacturer, its service agent
or similarly qualied persons in
order to avoid a hazard.
2. This appliance is not intended for use by persons (including children) with reduced
physical, sensory or mental capabilities,
or lack of experience and knowledge, unless they have been given supervision or
instruction concerning use of the appliance
by a person responsible for their safety
3. Children should be supervised to ensure that they do not play with the appliance
• Assembly
1. Place Stand A on Stand B to form X-base.
2. Place lower pipe with pipe support on X-base with four screws provided.
3. Loosen and remove the pipe connector from lower pipe.
Slide plastic base ornament over lower pipe onto the base.
Extend upper (inner) pipe and slide pipe connector over upper pipe into lower pipe and tighten.
4. Attach the motor with switch housing onto the upper pipe.
Ensure the switch housing is pushed fully onto the upper pipe and secured with the
screw provided.
5. Loosen guard mounting nut from the motor housing.
6. Position rear guard rmly to motor housing and then fasten by turning guard mounting nut
clockwise tightly.
7. Remove and discard the PVC sleeve on the motor shaft.
8. Push the blade along motor shaft and fasten it rmly with spinner by turning counter clockwise.
9. Hang the front guard to rear guard with the position xer provided at the rim of guard and then
x together with screws and clips provided
1
2
RAMTONS RM/287 User manual
AirKing 4CH63D Operating instructions
Campomatic SF200R SF300R Owner's manual
United USF634 Operating instructions
Bahamas Breeze FS45-3ER Owner's manual
Lasko 1850 User manual
Lava Aire Fantom User manual
