ZQP-TV51STDA

GODEER ZQP-TV51STDA User manual

Hello, I'm your chat assistant. I have read the user manual for this TV stand. This document provides assembly instructions and guidance, like how to make sure hardware is tightened, ensure proper screw alignment, and set up the LED lights. I am ready to answer any specific questions you may have about this product.
What should I check if the LED lights are not working?

What do I need to do with the A hardware?

40PCS 40PCS 32PCS 6PCS 1PCS 8PCS 20PCS40PCS 20PCS 5PCS

3*12

1PCS

①

②

③

④

⑤

⑥

⑦

⑦

⑧

⑧

⑨

⑩

⑪

⑪

⑫

⑫

⑫

⑬

⑭

⑭

⑮

⑯

12 3 4

5 6 7 8

9 10 11 12

13

1PCS

1PCS

1PCS 1PCS 1PCS 1PCS

2PCS2PCS1PCS

1PCS 2PCS 3PCS

2000*365 356*365

447*333

1051*60 250*60

1038*365

1968*365 356*365

340*365 340*365 470*370

1051*216 1700*60

14 15 16

459*350 1046*151 1046*192

1PCS 2PCS 1PCS 1PCS

Ⅰ Ⅱ

Ⅲ Ⅳ

Scan QR code for assembly video

1

①

②

②

⑪

⑪

⑩

Put A on board ①②⑩⑪

Put C on board ①②⑪

2

③

④

⑤

⑥

⑧

⑧

⑨

⑫

⑫

⑫

G

⑬

Put A on board ③④⑤⑥

Put C on board ③④⑤⑥⑫⑬

3

①

J

4

⑪

⑪

⑪

⑪

⑫

⑫

⑫

⑫

⑫

⑫

②

Make sure the arrow on the screw align to the hole on the side

Put B on board ⑪⑫

5

⑬

⑬

⑤

⑤

⑥

⑥

⑯

②

Put B on board ⑤⑥⑬

6

⑬

⑤②

⑥

⑤

⑬

⑥

②

③

③

④

④

⑭

⑭

⑮

Put B on board ②

7

①

①

③

③

⑤

⑤

⑬

⑥④

⑩

④

⑥

②

②

Put B on board ①③④⑤⑥

8

①

①

③

③

④

④

⑦

⑦

⑩

⑩

⑧

⑧

F

G

D

9

①

③⑧

⑧

⑨

⑨

⑤

②

⑩

E

G

10

①

⑭

⑭

⑮

⑯

If you can’t let the lights work successfully, please check the

following:

1. Please check the direction of the connect, try it in the opposite

direction, according to the following picture.

2. Please check the remote control, it need you to tear down the

plastic septum before use it.

3. Don’t let the remote control too far from the receiver, make sure

there is no obstruction between them.

LED Light

2108057ZBJMY

/

Other documents